Chapter 5

Heat Exchangers

1
 Chapter 6: Heat exchangers
Introduction
• Device that facilitate the exchange of heat
between fluids that are at different temperatures
while keeping them from mixing with each other.

• Heat exchanger involves convection in each

fluid and conduction through wall that separating
the two fluids

• It is convenient to use an overall heat transfer

coefficient (U)
2
HEAT EXCHANGERS
Hot In Hot Out

Cold Out Cold In

3
 Liquid Flow

Gas Flow Plate

Tube 4
 Heat Exchangers
The most common types of energy conversion
systems (e.g. internal combustion engines,
gas/steam turbines, boilers) consist of three parts:

1. a combustion process generating heat and

kinetic energy (K.E.)
2. a device for converting K.E. to mechanical
(useful) energy
3. heat exchangers to recuperate the heat
either for heating purposes or to increase
efficiency.
5
 Heat Exchangers are classified according to
their function and geometry:

Function:
1. Recuperative: two fluids separated by a solid
wall (this is the most common type)
2. Evaporative: enthalpy of evaporation of one
fluid is used to heat or cool the other fluid
(condensers/evaporators and boilers)
3. Regenerative: use a third material which
stores/releases heat

Types: 1. Double Tube (concentric- tube)

2. Shell and Tube
3. Cross-flow
4. Compact
6
1. Double Pipe Heat Exchangers

7
Advantages:

- low pressure loss

- small applications (simple, cheap to build)
- counter flow: high effectiveness; parallel flow:
quick (short) fetches.

Disadvantage:

- requires large surface area (footprint on floor) if

large heat transfer rates are needed.

8
2. Shell-and-Tube Heat Exchangers:

9
 One-shell passes and one-tube passes

10
One-shell passes and two-tubes passes
11
12
Advantages:

- ideal for large scale applications

- commonly used in petrochemical industry where
dangerous substances are present (protective
shell)
- compact design or double tube heat exchanger.

Disadvantages:

- very bulky (heavy construction), baffles are used

to increase mixing
- subject to water hammer and corrosion (behind
baffles)
- high pressure loses (recirculation behind baffles)
13
 3. Cross flow heat exchangers

Both fluids unmixed One fluid unmixed

14
Both fluids unmixed
Overview: Cross-flow and compact heat
exchangers are used where space is limited. These
aim to maximize the heat transfer surface area.

Cross-flow Heat Exchangers:

Commonly used in gas (air) heating applications.
The heat transfer is influenced by whether the
fluids are unmixed (i.e. confined in a channel) or
mixed (i.e. not confined, hence free to contact
several different heat transfer surfaces).
e.g.: both fluids unmixed: air-conditioning devices
e.g.: both fluids mixed: boilers 15
Advantage: large
Cross-Flows
surface area-good may be mixed
for transferring or unmixed

heat to gases
Disadvantages:
heavy, high
pressure losses

In a cross-flow heat exchanger the direction of fluids are

perpendicular to each other. The required surface area,
Across for this heat exchanger is usually calculated by
using tables. It is between the required surface area for
counter-flow (Acounter) and parallel-flow (Aparallel) i.e.
16
Acounter< Across <Aparallel
4. Compact heat exchangers

17
Compact heat exchangers

18
Compact heat exchangers: These are cross-flow
heat exchangers characterized by very large heat
transfer area per unit volume. In fact, the contact
area is so large that much of the flow behaves as
duct or channel flow.

For this reason, the heat-transfer is dominated by

wall effects and the characteristics cannot be
evaluated as for the other types.

For these heat exchangers, the heat transfer rate is

directly related to pressure loss.

19
Advantages:
- very small
- ideal for transferring heat to/from fluids with
very low conductivity or where the
heat transfer must be done in very small
spaces (e.g. electronic component cooling,
cryogenic cooling, domestic furnaces).

Disadvantages:
- high manufacturing costs
- very heavy
- extremely high pressure losses.
20
Overall heat transfer coefficient in
heat exchanger

21
22
23
24
25
 Underlying calculation approach
The heat transfer rate for most heat exchangers
can be calculated using the LMTD-method (Log
Mean Temperature Difference), if the inlet (T1) and
outlet (T2) temperatures are known:

Q  U A T
T2  T1
T  F
ln T2 / T1 
U = Overall heat transfer coefficient [ W/m2-oC ]
A = Effective heat transfer surface area [ m2 ]
F = Geometry correction factor
T = Log mean temperature difference 26
 General Formulation for Heat Exchanger
Analysis (LMTD-method)
Most heat exchangers are characterized relative to a
double-pipe heat exchanger (H = Hot, C = Cold):

T1
T2

27
 Q  U A T
T2  T1
T  F
ln T2 / T1 
T1  Th, i  Tc, i 
For parallel-flow heat exchanger:  
T2  Th, o  Tc, o 

For counter-flow heat exchanger: T1  Th, i  Tc, o 

 
T2  Th, o  Tc, i 

Comparison of parallel flow and counter-flow operations

• For the same inlet and outlet temperatures, ΔTlm, counterflow > ΔTlm, parallel flow.
Hence, counter-flow operation performs better than parallel flow operation.

• Tc,o can exceed Th,o for counter-flow but not for parallel flow.
28
We now want to derive the expression for LMTD
for a counter-flow double-pipe heat exchanger.
This will be done by considering the first law (for
counter flow):

First globally:

 CH THi  THo   m

Q  U A T  m  CC TCo  TCi 

Then locally: Apply the first law between points 1

and 2 (for counter-flow)

Heat lost by hot side = Heat gained by cold side

29
For counter-flow:

THo  THi   TCo  TCi  THo  TCi   THi  TCo 

QUA UA
 THo  TCi   THo  TCi 
ln   ln  
 THi  TCo   THi  TCo 

T2  T1
QUA
 T2 
ln  
 T1 

By using the notation 1 and 2, as shown on the

graphs, this definition is valid for both Counter-
current and Co-flow (parallel) double-pipe heat
exchangers.
30
 ξ-NTU (Effectiveness – Number of Transfer
Units) Method
If the inlet or outlet temperatures are not given,
the LMTD-method becomes cumbersome to use.
It is thus advisable to use the Effectiveness-NTU
method. The method can be formulated from
the following definitions:

Effectiveness:
Actual heat transfer Q
 
Theoretica l max . heat transfer Q max
UA
NTU 
m
 Cmin
Minimum thermal capacity
 max. temp. difference
31
NTU : Number of Transfer Units
In general:

Actual heat transfer is given by

 CH THi  THo   m

Q  m  CC TCo  TCi 

Theoretical maximum heat transfer by:

 Cmin THi  TCi 

Q  m
Hence, we obtain the effectiveness as:

m CH THi  THo  m CC TCo  TCi 

 
m Cmin THi  TCi  m
 Cmin THi  TCi 
32
For a counter-flow heat exchanger:

Let m
 CH  m
 Cmin

and m
 Cmin m
 CH
R 
m
 Cmax m
 CC

Which, on using the definition for LMTD, leads to

an expression for the effectiveness as:
 NTU 1  R 
1 e
  NTU 1  R 
1 R e 33
 Counter flow Parallel flow

m
 CC  m
 CH m
 CC  m
 CH 34
Similar expressions are used for other types of
geometry.

For example, for a parallel double-pipe heat

exchanger, the effectiveness is:
 NTU 1  R 
1 e

1 R

Next we shall look at some applications of these

concepts.
35
 Typical thermal design problems

• Problem #1
– Given the entrance temperature of the two
streams, given one exit temperature;
– Find heat transfer area, A.
• Problem #2
– Given entrance temperature of the two
streams, given the heat transfer area, A;
– Find the exit temperatures of the two
streams.

36
Objective: Calculation procedure and advantages
/ disadvantages of:
Double pipe
Shell and tube
Cross flow heat exchangers

1. Double Pipe Heat Exchangers:

37
Double Pipe Heat Exchangers
38
Arrangements:

39
2. Shell-and-Tube Heat Exchangers:

40
Heat transfer calculations:

Q  U A T

T2  T1
T  F
ln T2 / T1 

Using counter flow, double pipe heat exchanger

definition for the temperatures

T2  THo  TCi T1  THi  TCo

41
 Heat exchanger correction factor plot for one
shell pass and an even number of tube passes

= +

42
Heat exchanger correction factor plot for two shell
passes and twice an even number of tube passes

43
For n-shell passes with an even number of tubes:

Again, for boiling or evaporation R  0

so that  = 1 – e-NTU
44
 Cross flow heat exchangers

Both fluids unmixed One fluid unmixed

45
Both fluids unmixed
Cross-flow heat exchangers have the same
analysis equations as before:

Q  U A T
T2  T1
T  F
ln T2 / T1 

with F as the correction factor (see graphs). The

-NTU method may also be used

46
Heat exchanger correction factor plot for single
pass, cross-flow with one fluid mixed

47
Heat exchanger correction factor plot for single
pass, cross-flow with both fluids unmixed

48
Compact heat exchangers

49
To solve problems involving design and selection
(sizing) of compact heat exchangers it is first
required to find the effective pressure (static)
loss. This loss can be shown, based on
fundamental heat transfer principles, to be
directly related to the heat transfer rate based on
Colburn’s analogy:

f 2
jH   St Pr 3
8
f – friction factor, St – Stanton number,
Pr – Prandtl number and jH = Colburn factor
50
These calculations can be quite involved and so
most design or sizing applications use data in
tables and graphs.

All material properties are calculated at the bulk

average temperature, i.e. at (T1+T2)/2, if T1 = inlet,
T2 = exit
 
Pr andtl number Pr  
  Cp
dP
 DH
Friction factor f dx
 Umax
2
51
Reynolds number at the smallest diameter:

DH G m
Re  G
 Ac

DH = hydraulic diameter at smallest cross-section

= 4 Ac / P
Ac = smallest cross-sectional area
P = perimeter (circumference) of tube
µ = dynamic viscosity
 = thermal diffusivity
G = maximum mass flow rate flux
 = mass flow rate
m
52
 Ac h
 St 
A G Cp
 = ratio of open area to total frontal area (A)
h = heat transfer coefficient
Cp = specific heat capacity

V1 G2  2  V2  A Vm 
p   1      1  f 
2   V1  A c V1 
p = pressure loss through heat exchanger
Vm = (V2 + V1) / 2
53
Overall heat transfer coefficient UA is computed
from:
1 1 1
 
U A h A c h A h
(h A)h = hot fluid
(h A)c = cold fluid
A = effective heat transfer area

Then the heat transfer Q is:

Q  U A T
54
Heat transfer and friction factor for a finned flat tube
heat exchanger

55
Heat transfer and friction factor for a finned circulator-tube
heat exchanger (details on next slide)

56
57
Summary

58
 Summary of effectiveness equations

Heat exchanger Effectiveness:

type:

59
Heat exchanger Effectiveness:
type:

= +

60
Heat exchanger Effectiveness:
type:

61
Example questions

62
Example 1 – Finned flat tube heat exchanger

Air at 1 atm and 300 K enters a finned flat tube

heat exchanger (as in graph in an earlier slide)
with a velocity of 15 m/s. Calculate the heat
transfer coefficient (h).

Note at this temperature the air properties

(found from tables) are:

 = 1.1774 kg/m3
 = 1.983 x 10-5 kg/ms
Cp = 1.0057 kJ/KgoC
Pr = 0.708
63
Example 2 – Shell and tube heat exchanger

Hot oil at 100oC is used to heat air in a shell and

tube heat exchanger. The oil makes 6 tube passes
and the air makes 1 shell pass. 2.0 kg/s of air
(specific heat of 1009 J/kgoC) is to be heated from
20 to 80oC. The specific heat of the oil is 2100
J/kgoC and its flow rate is 3.0 kg/s. Calculate the
area required for the heat exchanger for U = 200
W/m2oC.

64
Example 3 – Finned-tube (both fluids unmixed)
cross-flow heat exchanger
A finned-tube exchanger is used to heat 2.36 m3/s
of air (specific heat of 1006 J/kgoC) at 1 atm from
15.55 to 29.44oC. Hot water enters the tubes at
82.22oC and the air flows across the tubes,
producing an average overall heat transfer
coefficient of 227 W/m2oC. The total surface area of
the exchanger is 9.29m2. Calculate the heat transfer
rate (kW) and the exit water temperature.
Note: We don’t know whether the air or the water is
the minimum thermal capacity fluid. So try with the
air as the minimum fluid first and see if the -NTU
equations give a possible solution. If not then we
have to use water as the minimum and iterate to a
solution. 65