Perfectly adapted to DENSOLEN ®
tapes and tape systems.
Outstanding resistance against
cathodic disbondment.
For steel and other metal surfaces.
Compatible with factory coatings
made of PE, PP, FBE, PU, CTE and
bitumen.
For the application with roller or
brush.
Dries fast and is easily processed.
For a century now, DENSO Group Germany represents experience, quality and reliability for corrosion prevention and sealing technology.
The success of the internationally leading corporation is based on the development of the "DENSO-Tape", which was already patented in 1927
as the first product worldwide for the passive corrosion prevention of pipelines. Since then, the DENSO Group Germany establishes and
guarantees the highest quality standards with technically trend-setting products. Research, development and production take place
exclusively in Germany. Our employees continuously implement safe and individual solutions in a personal cooperation with the customer.
DENSOLEN ®-HT/-MT Primer is an DENSOLEN ® -MT25 Primer) climatic DENSOLEN ® -HT/-MT Primer is
integral part of all DENSOLEN ® conditions. applied.
tape systems and is applied as
DENSOLEN ® - HT/-MT Primer pro- It is recommended to repeat the
prime coat before the wrapping of
vide a high yield. A thin covering prime coat at the latest after 6
the DENSOLEN ® tapes on the metal
coating is adequate. The areal cov- hours if the application of a
surface and adjacent factory coat-
erage is app. 0.2 liter per m². DENSOLEN ® tape system cannot be
ings.
started immediately after the dry-
DENSOLEN ® - HT/-MT Primer im-
DENSOLEN ®-HT/-MT Primer is ing of the primer.
proves the peel strength of
based on naphtha (petroleum
DENSOLEN ® tape systems on the DENSOLEN ® -HT/-MT Primer can be
spirit) and it includes butyl rubber
metal surface as well as on the processed with a brush or a paint-
as well as resins for an optimal
factory coating and therefore sup- er's roller.
adhesive connection between the
ports the permanent corrosion
DENSOLEN ® tapes and the pipe The prime coat must be dry before
protection.
surface. the application of the DENSOLEN ®
DENSOLEN ® -HT/-MT Primer can tapes. The drying time is approxi-
DENSOLEN ®-HT/-MT Primer is
also be used to temporarily protect mately 5 to 25 minutes depending
available on the basis of two sol-
sandblasted surfaces against a rust on the primer type, the ambient
vents with different volatilization
film. temperature, the air movement and
ranges. This means that optimal
the moisture.
processing conditions are achieved The surface must be cleaned (sur-
for cold (e.g., DENSOLEN ® -HT face cleanliness ST2 or SA 2.5 in
Primer as well as warm (e.g. accordance with ISO 8501-3) before
Typical values
Property Unit Test method
HT HT25 MT25
Petroleum Petroleum Petroleum
Solvents - -
spirit spirit spirit
Flash point °C (°F) -18 (-0.4) -18 (-0.4) +23 ( +73.4) DIN EN 57
Density +23°C/ +73.4°F g/cm 3 0.79 0.78 0.80 DIN 51757
Solids content wt% 30 24 24 ISO 1515
Aromatics content wt% <0.0005 <0.0005 <0.01 -
1)
Drying time for manual application min (app.) 5 to 10 5 to 10 20 to 25 -
Maximum waiting time for the DENSOLEN ® tape application h <8 <8 <8 -
Consumption l/m 2 0.2 0.2 0.2 -
2) -60 to +100 -60 to +100 -60 to +100
Operating temperature °C (°F) -
(-76 to +212) (-76 to +212) (-76 to +212)
1)
Depending on the temperature, humidity, air movement and surface temperature of the pipe.
2)
Depending on the DENSOLEN® tape system used.
Processing temperature
Environment -40°C to +60°C (-40°F to +140°F)
Pipe surface min. +3°C (+5.4°F) above the dew point max. +85°C (+185°F)
Packaging Content (l) Gross weight (kg)
4 cans per box 1 0.92
Metal bucket 5 4.70
Metal bucket 10 8.70
Barrel 180 168
DENSO GmbH
Our product information, our application recommendations and other The user is responsible for checking the applications of the product and
product related documents are made for your convenience only. verifying its suitability for the intended use.
P.O. Box 150120 | 51344 Leverkusen | Germany Since many installation factors are beyond our control, the user shall Our General Terms of Sale, which are available at www.denso.de, shall
determine the suitability of the products for the intended use and be decisive without any exception.
Phone: +49 214 2602-0 | Fax: +49 214 2602-217
assume all risks and liabilities in connection therewith. This is a translation from the original German product information.
www.denso.de | [email protected] All information contained in this document is to be used as a guide and In case of any discrepancy or any dispute arising on the interpretation of this
does not constitute a warranty of specification. The information contained product information, the German text of the respective German product
in the document is subject to change without notice. For this reason, no liability information, which is available at www.denso.de, shall be decisive.
can be accepted for inaccurate advice or any failure to provide advice. The legal relationship shall be governed by German law. 12.2016
Real co-extruded 3-ply tape.
No spiral corrosion hazard as com-
pared to the two-ply tape.
DIN-DVGW certified systems for class
B 50 in accordance with EN 12068.
Compatible with factory coatings
made of PE, PP, FBE, PU, CTE and bi-
tumen.
Outstanding tape elasticity and elon-
gation at break.
Cost effective system with outstand-
ing price/performance ratio.
For a century now, DENSO Group Germany represents experience, quality and reliability for corrosion prevention and sealing technology.
The success of the internationally leading corporation is based on the development of the "DENSO-Tape", which was already patented in 1927
as the first product worldwide for the passive corrosion prevention of pipelines. Since then, the DENSO Group Germany establishes and
guarantees the highest quality standards with technically trend-setting products. Research, development and production take place
exclusively in Germany. Our employees continuously implement safe and individual solutions in a personal cooperation with the customer.
DENSOLEN ®-AS30/-R20 MP is a cold (Reg.No.: NG-5180CP0056) area and creates a hose-type encase-
applied tape system for corrosion pre- EN 12068 B 50 ment, which results in a reliable and du-
vention of metal pipes and pipelines with rable corrosion protection.
®
The system DENSOLEN -AS30/-R20 MP
outstanding economic and qualitative An outstanding connection between the
consists of:
properties. Due to the innovative for - adhesive and the carrier film is guaran-
®
DENSOLEN - HT Primer
mula, the tapes grow completely together teed by the co-extruded intermediate
A solvent containing primer for corrosion
in the overlapping area and create a long - layer.
prevention in combination with
lasting hose-type encasement.
DENSOLEN ® tapes. For the processing in DENSOLEN ® -R20 MP
DENSOLEN ®-AS30/-R20 MP fulfills the re-
hot environments, the DENSOLEN ® -MT25 A co-extruded two-layer plastic tape
quirements of the impact resistance of
Primer can be used as an alternative. made from robust white polyethylene
class B 50 in accordance with EN 12068
Please refer to the separate product data carrier film with a single side butyl rubber
and even the indentation resistance of
sheet DENSOLEN ® - Primer. coating. An outstanding connection
class C 50.
DENSOLEN ®-AS30/-R20 MP is basically ® between the adhesive and the carrier film
DENSOLEN -AS30
impermeable for water vapor and oxygen is achieved by the co-extruded
A real co-extruded 3-ply plastic tape
and it is resistant against soil bacteria intermediate layer. The butyl rubber
made from stabilized polyethylene carrier
and electrolytes. adhesive layer grows completely together
materials with butyl rubber adhesive on
DENSOLEN ®-AS30/-R20 MP is compati- ® with the out- side layer of DENSOLEN ® -
both sides. DENSOLEN -AS30 grows
bele with factory coatings made of PE, PP, AS30.
completely together in the overlapping
FBE, PU, CTE und Bitumen.
Standard designation:
Butyl rubber adhesive
PE carrier material PE carrier material
PE butyl rubber (co-extruded)
PE butyl rubber (coextruded)
Butyl rubber adhesive
Butyl rubber adhesive
®
Schematic cross section of DENSOLEN -AS30 ®
Schematic cross section of DENSOLEN -R20 MP
DENSOLEN ®-AS30 DENSOLEN ®- R20 MP
Property Unit Test method
Typical value Typical value
Carrier film color - Black White -
Butyl adhesive color inside - Gray Black -
Butyl adhesive color outside - Black - -
Total thickness mm 0.5 0.5
Carrier film thickness app. mm 0.3 0.3 ISO 4591
Inside adhesive layer thickness app. mm 0.2 0.2 ASTM D1000
Outside adhesive layer thickness mm 0.08 -
Elongation at break % 600 500 DIN 30672
Tape strength +23°C (+73.4°F) N / cm 65 65 EN 12068
Dielectric strength kV / mm 40 50 ASTM D149
DENSOLEN ® -AS30/-R20 MP with DENSOLEN ® -HT Primer
®
DENSOLEN -AS30/-R20 MP Required
Property Unit value Test method
Typical value
2 11 6
Specific electrical insulation resistance Ohm m 10 10 EN 12068
Volume resistivity Ohm cm 1016 Not stated ASTM D257
+23°C (+73.4°F) +50°C (+122°F)
Peel resistance
N / cm 15 2.0 4 0.4 EN 12068
metal/primer/tape
33 2.5 Not stated ASTM D1000
Peel resistance layer to layer
+23°C (73.4°F) +50°C (+122°F)
AS30 / AS30 N / cm 22 4.0 8 2 EN 12068
AS30 / R20 MP 22 3.5 8 2
R20 MP / R20 MP 4 3.5 2 2
Indentation resistance - residual layer thickness +50°C (+122°F)
for stamp load 1N / mm², stamp-Ø 5.65 mm mm > 1.3 (fulfills class B) > 0.6 EN 12068
for stamp load 10 N / mm², stamp-Ø 1.8 mm > 0.6 (fulfills class C) > 0.6
Impact resistance J 10 8 EN 12068
Cathodic disbondment resistance (radius) mm <2 < 20 EN12068
Lap shear strength +23°C (+73.4°F)
on steel N / cm2 8 5 EN 12068
on factory coating 8 5
Water vapor permeability g /m 2 24h < 0.2 Not stated ASTM E96
® ®
DENSOLEN tapes can be easily applied manually. The processing with the original DENSOMAT wrapping devices is even more effi-
cient. For DENSOLEN® tapes with width of > 50 mm, we recommend the use of the DENSOMAT® wrapping device to guarantee an
excellent processing quality.
Tape area Content per box
Core diameter Tape length
Width [mm] per roll Number Total tape Total tape App weight
(mm) [m]
(m 2 ) of rolls area (m²) length (m) (kg)
50 30 1.5 10 15 300 10
41 100 30 3.0 5 15 150 10
DENSOLEN ® -AS30 150 30 4.5 5 22.5 150 15
100 70 7 3 21 210 13
78
150 70 10.5 2 21 140 13
50 30 1.5 12 18 360 11
41 100 30 3.0 6 18 180 11
DENSOLEN ® -R20 MP
150 30 4.5 6 27 180 17
100 70 7 3 21 210 13
78
150 70 10.5 2 21 140 13
Additional dimensions available on request.
DENSO GmbH
Our product information, our application recommendations and other Our General Terms of Sale, which are available at www.denso.de, shall
product related documents are made for your convenience only. be decisive without any exception.
P.O. Box 150120 | 51344 Leverkusen | Germany Since many installation factors are beyond our control, the user shall This is a translation from the original German product information.
determine the suitability of the products for the intended use and In case of any discrepancy or any dispute arising on the interpretation of this
Phone: +49 214 2602-0 | Fax: +49 214 2602-217
assume all risks and liabilities in connection therewith. product information, the German text of the respective German product
www.denso.de | [email protected] All information contained in this document is to be used as a guide and information, which is available at www.denso.de, shall be decisive.
does not constitute a warranty of specification. The information contained The legal relationship shall be governed by German law. 10.2015
in the document is subject to change without notice.
