CP4N

4-Series™ Control System

Modular Programming Architecture
The CP4N provides a modular programming architecture that
allows the CP4N to run up to ten programs simultaneously.
Programmers can develop and run independent,
device-specific programs, enabling each program to be
optimized for a specific function and allowing for changes to
be made to one program without affecting the whole system.
Dedicated Control Subnet
l 4-Series™ control system with 2 GB SDRAM and 8 GB flash The Crestron Control Subnet is a Gigabit Ethernet network
memory dedicated to Crestron devices. Via the Control Subnet port, an
l Embedded 4-Series multicore CPU processor installer can connect a single touch screen or wireless gateway
or can add a Crestron PoE switch (CEN-SW-POE-5 or
l iPhone®, iPad®, and Android™ device control app support CEN-SWPOE-16, both sold separately) to handle multiple
l XPanel computer and web based control touch screens, gateways, AV components, and other devices.
l Modular programming architecture Automatic configuration of the entire subnet is performed by
the CP4N, discovering each device and assigning IP addresses
l Onboard IR/serial, COM, I/O, relay, Cresnet® network, and without any extra effort from the installer.
high-speed gigabit Ethernet control ports
l Control subnet port providing a dedicated local network for NOTE: The Control Subnet port does not supply any PoE
Crestron® devices power to connected devices
l High-speed USB 2.0 host port memory card slot
l Support for Crestron Fusion® software and XiO Cloud® A separate LAN port provides a single-point connection to the
service local network, requiring only one IP address for the entire
l Enterprise-class network security and authentication control system. The LAN port allows for interconnectivity
between devices on the local subnet and other devices,
l SNMP V3 remote IT management support systems, servers, and WAN/internet connections outside the
l Native BACnet network/IP support local subnet. For sensitive applications that require
l Installer setup via software, web browser, or cloud heightened security, the entire Control Subnet can be isolated
completely from the local network.
l IPv6 ready
Onboard Control Ports
l Integrates with Apple® HomeKit® technology
Through a full complement of onboard control ports, the
l Rack mountable
CP4N can be integrated with a wide variety of audio, video,
The CP4N is a secure, high-performance control processor lighting, motorized shades, thermostats, door locks, sensors,
with a powerful 4-Series™ control engine. The CP4N is security systems, and other equipment.
designed to integrate and automate technology within any l Gigabit Ethernet provides an interface for connecting to
modern networked home, commercial building, or government
the building network and controlling Crestron AV
facility. An isolated control subnet port provides a Gigabit
switchers, audio processors, power controllers, and other
Ethernet LAN dedicated to Crestron devices.
IP controllable equipment.
4-Series Control Engine l Cresnet® network connectivity provides support for
4-Series control systems come equipped with an upgraded Crestron lighting dimmers, motorized shades, sensors,
multicore CPU, delivering a sizable speed and performance thermostats, keypads, and more.
increase compared to all Crestron 3-Series® control l Onboard RS-232, IR/serial, relay, and Versiport I/O control
processors. The improved performance allows 4-Series control ports enable direct integration with all types of
systems to handle the increasing demands of an advanced third-party equipment.
automated system. Crestron 4-Series delivers a dynamic and
secure control system platform capable of managing a room Expanded connectivity can be provided to the CP4N via
full of disparate technologies. Crestron control port expansion modules, Ethernet to Cresnet
bridges, wired Ethernet I/O modules, wireless network I/O
Reliable networking and IP control afford seamless modules, or infiNET EX® network wireless gateways (all sold
integration with other systems and devices, with add-on separately).
control capability using Crestron touch screens, wireless
remotes, and mobile device apps, as well as remote
management through Crestron Fusion® software and the
XiO Cloud® service.
CP4N
4-Series™ Control System
Crestron Fusion Room Monitoring and Scheduling Apple HomeKit Integration
Crestron Fusion provides an integrated platform for creating The CP4N supports integration with an Apple® HomeKit®
smart buildings that save energy and enhance worker technology system. Once the CP4N is paired with a HomeKit
productivity. As part of a complete managed network in a system via SIMPL programming, a Crestron TSR-310 can be
corporate enterprise, college campus, convention center, or used to control supported Apple devices. A pairing QR code is
any other facility, the CP4N works with Crestron Fusion to affixed to the CP4N that makes it easy to pair the control
enable remote scheduling, monitoring, and control of rooms system directly to the Apple Home app.2
and technology from a central help desk or mobile app. It also
enables organizations to reduce energy consumption by
tracking real-time usage and automating control of AV,
lighting, shades, and HVAC. For more information about
Crestron Fusion, visit www.crestron.com/fusion.
XiO Cloud Provisioning and Management
4-Series control systems leverage the power and flexibility of
XiO Cloud services, enabling users to remotely provision,
monitor, and manage Crestron devices across an enterprise
network. XiO Cloud can be used to configure and load
programs to the control system before it is received, making
the control system fully functional as soon as it is connected
to the network. XiO Cloud is built on the Microsoft® Azure®
software platform and utilizes Microsoft's industry leading
Azure IoT Hub technology. XiO Cloud enables installers and IT
managers to deploy and manage thousands of devices in the
time it previously took to manage just one. Unlike other virtual
machine based cloud solutions, Azure services provide
unlimited scalability to suit the ever growing needs of an
enterprise. For more information, visit
www.crestron.com/xiocloud.
Enhanced Enterprise-Grade Security
The CP4N is an enterprise-class control processor that can be
deployed across hundreds of spaces and set up easily using a
web browser, Crestron Toolbox™ software, or XiO Cloud. It
employs standard network security protocols, including 802.1X
network access control, Active Directory® service
authentication, SSH, TLS, and HTTPS to ensure reliability and
compliance with your organization’s IT policies.
The CP4N is configured to meet Crestron's enhanced security
standards right out of the box. The CP4N ships with
authentication enabled and requires that an administrator
account be created before access is granted to device
configuration and control interfaces.
SNMP V3 Support
Built-in SNMP V3 support enables integration with third-party
IT management software, allowing network administrators to
manage and control Crestron systems on the network in an
IT-friendly format.
BACnet Support
Native support for the BACnet communication protocol
provides a direct interface to third-party building
management systems over Ethernet, simplifying integration
with HVAC, security, and other systems. Using BACnet, each
system runs independently but communicates together on one
platform.1
CP4N
4-Series™ Control System
Specifications Connectors and Card Slots

Control Engine RELAY OUTPUT (2) 8-pin 3.5 mm detachable terminal

1–8 blocks;
Crestron® 4-Series™; real-time, preemptive Comprises (8) normally open, isolated
multithreaded/multitasking kernel; Transaction-Safe relays;
Extended FAT file system; supports up to 10 simultaneously Rated 1A, 30VAC/VDC;
running programs MOV arc suppression across contacts
I/O 1–8 (1) 9-pin 3.5 mm detachable terminal
Communications block;
Ethernet 100/1000 Mbps, autoswitching, Comprises (8) Versiport digital
autonegotiating, autodiscovery, full/half input/output or analog input ports
duplex, industry-standard TCP/IP stack, (referenced to GND);
UDP/IP, CIP, DHCP, SSL, TLS, SSH, SFTP Digital Input: Rated for 0–24VDC, input
(SSH File Transfer Protocol), FIPS 140-2 impedance 20k Ω, logic threshold >3.125V
compliant encryption, IEEE 802.1X, low/0 and <1.875V high/1;
SNMP, BACnet and IP1, IPv4 or IPv6, Digital Output: 250 mA sink from
Active Directory® service authentication, maximum 24VDC, catch diodes for use
HTTPS web server, HTTPS web browser with real world loads;
setup and XiO Cloud® client, SMTP email Analog Input: Rated for 0–10VDC,
client protected to 24VDC maximum, input
impedance 21k Ω with pull-up resistor
Control Subnet 100/1000 Mbps Ethernet, autoswitching, disabled;
autonegotiating, autodiscovery, full/half Programmable 5V, 2k Ω pull-up resistor
duplex, DHCP server, DNS server, port per pin
forwarding, isolation mode
IR - SERIAL (2) 8-pin 3.5 mm detachable terminal
Cresnet® Cresnet primary mode OUTPUT 1–8 blocks;
Network Comprises (8) IR output ports;
USB Supports USB mass storage class devices IR output up to 1.2 MHz;
via the rear panel USB 2.0 host port, 1-way serial TTL/RS-232 (0–5V) up to
supports computer console via the front 115.2k baud;
panel USB 2.0 device port IRP2 IR emitters sold separately
RS-232/422/485 For 2-way device control and monitoring, COM 1 (1) 5-pin 3.5 mm detachable terminal
COM port supports RS-232 up to 115.2k block;
baud with software handshaking, one Bidirectional RS-232/422/485 port;
port also supports RS-422 or RS-485 and Up to 115.2k baud; hardware and
hardware handshaking software handshaking support
IR/Serial Supports 1-way device control via COM 2–3 (2) 3-pin 3.5 mm detachable terminal
infrared up to 1.2 MHz or serial TTL/RS- blocks;
232 (0–5V) up to 115.2k baud Bidirectional RS-232 ports;
Up to 115.2k baud; software handshaking
Memory support

SDRAM 2 GB MEMORY (1) SD memory card slot;

Accepts one SD or SDHC card up to
Flash 8 GB 32 GB for storage of log files
Memory Card Supports SD and SDHC cards up to 32 USB (1) USB Type A connector, female;
GB USB 2.0 port for storage devices
External Storage Supports USB storage devices up to 1 TB LAN (1) 8-pin RJ-45 connector, female;
100BASE-TX/1000BASE-T Ethernet
port;
CONTROL (1) 8-pin RJ-45 connector, female;
SUBNET 100BASE-TX/1000BASE-T Ethernet
port;
Provides a dedicated local network for
Crestron devices
CP4N
4-Series™ Control System
NET (1) 4-pin 3.5 mm detachable terminal Cresnet Power 15 W (0.625A @ 24VDC) when powered
block; Usage by a Cresnet power supply only
Cresnet primary port; Available Cresnet 24 W (1A @ 24VDC) when powered by the
Outputs power to Cresnet devices only if Power included power pack only
the included power pack is connected to
the 24VDC power input jack; Power 15 W (not including any connected
Alternately functions as a Cresnet power Consumption Cresnet devices)
input to power the unit from a Cresnet
power supply; Environmental
See "Power" section below for additional Temperature 41 to 113°F (5 to 45°C)
details
Humidity 10% to 90% RH (noncondensing)
24VDC 2.0A (1) 2.1 x 5.5 mm DC power connector;
24VDC power input; Heat Dissipation 50 BTU/hr
PW-2420RU power pack included;
Passes through to the NET port to power Enclosure
Cresnet devices;
Chassis Metal, aluminum, black finish
See "Power" section below for additional
details Faceplate Extruded metal, black finish,
polycarbonate label overlay
G (1) 6-32 screw;
Chassis ground lug Mounting Freestanding or 1 RU 19-in. rack
mountable (adhesive feet and rack ears
COMPUTER (1) USB Type B connector, female;
included)
(front) USB 2.0 computer console port;
For setup only
Dimensions
Controls and Indicators Height 1.70 in. (44 mm) without feet
PWR (1) Green LED, indicates operating power Width 17.28 in. (439 mm);
is supplied from the power pack or 19.00 in. (483 mm) with rack ears
Cresnet power supply Depth 6.56 in. (167 mm)
NET (1) Amber LED, indicates communication
with Cresnet devices Weight
MSG (1) Red LED, indicates control processor 3.12 lb (1.42 kg)
has generated an error message
HW-R (1) Recessed push button, initiates Compliance
hardware reset
Regulatory Model: M201903003;
SW-R (1) Recessed push button, initiates UL® Listed for US & Canada, CE, IC, FCC Part 15 Class B
software reset digital device
LAN (rear) (1) Bicolor green/amber and (1) Amber
LEDs;
Green/amber LED indicates Ethernet link Models
status and connection speed;
CP4N
Amber LED indicates Ethernet activity
4-Series™ Control System
CONTROL (1) Bicolor green/amber and (1) Amber
SUBNET (rear) LEDs;
Green/amber LED indicates Ethernet link Included Accessories
status and connection speed;
Amber LED indicates Ethernet activity PW-2420RU
Desktop Power Pack, 24VDC, 2.5A, 2.1 mm, Universal
Power
Power Source Power pack or Cresnet (connect only one) Available Accessories
Options
For supported accessories, visit the CP4N product page at
Power Pack Input: 100–240VAC, 50/60 Hz; www.crestron.com.
(included) Output: 2.5A @ 24VDC;
Model: PW-2420RU
CP4N
4-Series™ Control System
Notes:
1. A BACnet and IP license is required. A free license is available to support up
to 50 BACnet objects on a single 4-Series control system. Enabling support
for more than 50 BACnet objects requires the purchase of one
SW-3SERIES-BACNET-50+ license. The CP4N supports a maximum of
1000 BACnet objects when dedicated for BACnet use only. Actual
capabilities are contingent upon the overall program size and complexity.
To obtain the license, visit www.crestron.com/bacnetlicense.
2. This feature is only available when using the TSR-310. Other Crestron
touch screens, handheld remotes, and keypads are not supported. For
these interfaces, traditional IR or CEC control must be used to control
supported Apple devices.

This product may be purchased from select authorized Crestron dealers and
distributors. To find a dealer or distributor, please contact the Crestron sales
representative for your area. A list of sales representatives is available online at
www.crestron.com/How-To-Buy/Find-a-Representative or contact us for
additional information by visiting www.crestron.com/contact/our-locations for
your local contact.
The original language version of this document is U.S. English.
All other languages are a translation of the original document.
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed online at
www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific
information, please visit www.crestron.com/opensource.
Crestron, the Crestron logo, 3-Series, 4-Series, Cresnet, Crestron Fusion,
Crestron Toolbox, infiNET EX, and XiO Cloud are either trademarks or
registered trademarks of Crestron Electronics, Inc. in the United States and/or
other countries. Apple, HomeKit, iPad, iPhone, and iPod touch are either
trademarks or registered trademarks of Apple, Inc. in the United States and/or
other countries. Android is either a trademark or a registered trademark of
Google Inc. in the United States and/or other countries. Active Directory, Azure,
and Microsoft are either trademarks or registered trademarks of Microsoft
Corporation in the United States and/or other countries. UL is either a
trademark or a registered trademark of Underwriters Laboratories, Inc. in the
United States and/or other countries. Wi-Fi is either a trademark or registered
trademark of Wi-Fi Alliance in the United States and/or other countries. Other
trademarks, registered trademarks, and trade names may be used in this
document to refer to either the entities claiming the marks and names or their
products. Crestron disclaims any proprietary interest in the marks and names of
others. Crestron is not responsible for errors in typography or photography.
Specifications are subject to change without notice.
©2022 Crestron Electronics, Inc.
Rev 11/22/22
CP4N
4-Series™ Control System