GTU-GSET 5/2/2024
Advance Steel Design
Subject Code: 3722007
8th Lecture
Dr. Kaushik Gondaliya
Assistant Professor,
Graduate School of Technology and Engineering,
Gujarat Technological Engineering,
Chandkheda, Ahmedabad - 382424.
Course Contents
• Properties of Steel: (5%)
• Mechanical Properties, Hysteresis, Ductility.
• Compactness and noncompactness, slenderness, residual stresses.
• Plastic Behavior of Structural Steel: (15%)
• Introduction
• Plastic theory
• Plastic hinge concept
• Plastic collapse load, conditions of plastic analysis
• Theorem of Plastic collapse
• Methods of Plastic analysis
5/2/2024 Advance Steel Design (372207) 2
Advance Steel Design (372207) 1
GTU-GSET 5/2/2024
Course Contents
• Design of Industrial Buildings: (20%)
• Introduction, selection of bay width, structural framing, purlins, girts and eave
strut, plane trusses
• Design of gantry girders
• Design of Cold-Formed Sections: (25%)
• Advantages, stiffened and unstiffened elements,
• local buckling and post buckling strength, shear lag and flange curling,
• unusually wide flange section, short span sections, members subjected to axial
tension, compression and bending.
• Design of beams and columns,
• Introduction to pre-engineered buildings using cold formed sections.
5/2/2024 Advance Steel Design (372207) 3
Course Contents
• Design of Steel Stacks: (20%)
• Introduction
• Proportioning of stack, Codal provisions
• Loads on Stacks, Load combinations, Stresses in Self-supporting stacks
• Design procedure for self-supporting stacks, Guyed steel stacks
• Design of Composite Structures: (15%)
• Composite Floor and Roof System Design, Composite beam
• Open web steel joist / joist girder, Serviceability requirements
5/2/2024 Advance Steel Design (372207) 4
Advance Steel Design (372207) 2
GTU-GSET 5/2/2024
Grading
• Two Quizzes (30% each) (Before and after mid-term)
• Mid-term Exam (30%)
• Final Exam (30%)
• Homework and Assignments (10%)
5/2/2024 Advance Steel Design (372207) 5
Contents
• Design of Steel Stacks: (20%)
• Introduction
• Proportioning of stack, Codal provisions
• Loads on Stacks, Load combinations, Stresses in Self-supporting stacks
• Design procedure for self-supporting stacks, Guyed steel stacks
5/2/2024 Advance Steel Design (372207) 6
Advance Steel Design (372207) 3
GTU-GSET 5/2/2024
Homework
5/2/2024 Advance Steel Design (372207) 7
8th Assignment
1. Classify the types of steel stacks based on the construction and
explain it. Which criteria should we consider for stability of
chimney.
2. Calculate and list out the wind load acting on self-supporting stack
of height 70 m above foundation. The diameter of the cylindrical
part of the chimney is 3 m. The chimney is situated on almost flat
terrain with category 1 at Ahmedabad. Divide entire chimney into
sections of 7 m height to find out wind load.
3. Explain in detail Vertical and Horizontal Forces acting on Steel
Stack.
5/2/2024 Advance Steel Design (372207) 8
Advance Steel Design (372207) 4
GTU-GSET 5/2/2024
8th Assignment
4. Write the design steps of Self-supporting steel stacks.
5. Design a self supported steel chimney (neglect seismic forces)
having a height of 50 m using following data. Take average wind
pressure = 1.2 kN/m2
a) Diameter of steel stack-= 3 m
b) Diameter of flare = 4 m
c) Height of flare = 14 m
d) Thickness of fire brick lining = 100 mm
e) Corrosion allowance = 3 mm
5/2/2024 Advance Steel Design (372207) 9
Thank you!!!
5/2/2024 Advance Steel Design (372207) 10
Advance Steel Design (372207) 5
