User Manual
K8
Before using this product pleasereadtheinstructions carefully
Foreword
Respected user:
Thank you for choosing our electric scooter. Please read
the operation manual :
[Link] charge before using for the first time.
[Link] red number on the key lock shows the voltage:
67V is full power, 50V is no power.
[Link] in deep water is strictly prohibited.
[Link] of unauthorized modification of vehicles.
[Link] wear a safety helmet when riding and pay
attention to safety!
Installation diagram
[Link] out the scooter and press the red fold button. Lift the
scooter handle. Then fasten the black folding hook.
Installation diagram
[Link] the vehicle handle and fender and tighten the screws
switch state
Notice: Because Of The Product Upgrade,
There May Be Some Difference Between The Product
Actually Get And The Instruction Manual.
Not Affecting The Normal Usage
Instrument and function introduction
[Link]
There are two buttons on the display panel, namely power button / boot
button and function button / mode mutton
[Link]
Long press to turn on the power, the battery power and speed are
displayed instantaneously according to the running status of the scooter, and the single
mileage and cumulative
1 mileage in the display are displayed according to the selected
function.
After the display panel is turned on, if there is no signal input for a long time (3
minutes), the panel will automatically turn off the power; when the panel shows CA
2:00, it means that it enters the countdown state, and will shutdown after 2hours.
Short press the function button to change the display content. The characters
TIME, TRIP, ODO, DST, VOL, CH 2:00 and so on appear respectively. When
appeared TIME, it means time, when appeared TRIP, it means single mileage, when
appeared ODO, it means accumulated mileage, when appeared DST, it means
remaining mileage (the electric scooter can still run range is based on the current
battery remaining capacity and the running status of the electric scooter in the last few
minutes). When VOL is appeared, it indicates the battery voltage; when CH 2:00 is
appeared, it indicates that it has entered a 2-hour shutdown countdown state (some
models do not have this). As time passes, the time display decreases.
Long press function button, clearance the single mileage (under TRIP content).
Short press power button, the gear number will flash, then press mode
button will change the gear, 1 is slow speed, 2 is medium speed, 3 is faster speed
gears. When the panel is turned on, long press power button to turn off the
power.
[Link] setting
When function button and power button at the same time, the panel
parameter setting state is entered:
When P0 is displayed, short press the function button again, P1 will be
displayed, and then short press function key, P2, P3, P4, P5, P6, P7 will be
displayed in turn; And they respectively indicated :
P0: the wheel diameter setting;
P1:the underpressure point setting;
P2: the magnetic pole logarithm setting;
P3: the speed measurement signal selection setting;
P4:KM or MILE selection setting;
P5: the non-zero start and zero start selection setting;
P6: the cruise and no cruise selection setting;
P7: the soft start and hard start Choose settings
1
When P0 is displayed, short press power button, the wheel diameter will be
displayed. To change the wheel diameter, press function button to increase by
1, or press power button to decrease by 1. After a few seconds, it will
automatically exit.
When P1 is displayed, short press power button to display the voltage value of
the battery undervoltage point; if it displays 315, it means that the undervoltage
value is 31.5 volts; to change the undervoltage value, press function button to
add 0.5, press power button to decrease 0.5;
When P2 is displayed, short press function button, the number of pole pairs of
the motor will be displayed,. You can press function button to increase 1 or
you can press power button to subtract 1;
When P3 is displayed, short press power button, it will display 0 or 1; it
indicates the speed measurement signal selection setting. When 0 is displayed (0
is generally selected), it indicates that the motor Hall signal is selected for speed
measurement. When 1 is displayed, the external signal is selected;
When P4 is displayed, short press power button, it will display 0 or 1,
indicating km / mile selective setting. When 0 is displayed, select kilometers, km
/ h will be displayed; when 1 is displayed, select miles, mp /h will be displayed;
When P5 is displayed, short press power button, 0 or 1 will be displayed,
indicating the choice of zero and non-zero start (some models do not have); when
0 is displayed, it indicates zero start; when 1 is displayed, PAS will appear,
indicating non-zero Zero start;
When P6 comes out, press power button, it will display 0 or 1 (some models
do not); it means there are cruise and no cruise options, when it shows 0, it means
no cruise; when it shows 1, it means there is cruise;
When P7 is displayed,
1
0 or 1 will be displayed, indicating hard start and soft zero
start selection (some models do not); when 0 is displayed, it indicates soft start
(soft when starting); when 1 is displayed, it indicates hard start (great momentum
at the start).
4. Fault display
When electric scooter broken down, the display panel will show the failed accessories,
including brake failure 、motor failure 、handlebar failure 、controller
failure etc.
Check before riding
1. The saddle must be adjusted in the correct position and the bolts must be locked.
2. The indicator is correct, the lamp and horn work normal.
3. The brake lever must be flexible and reliable, and the motor can be powered off
when braking.
4. The accelerator works flexibly and the reset function is normal.
5. The tires of the front and rear wheels have sufficient air volume without serious
wear and tear.
6. Flexible steering function without hindrance.
7. The front and rear wheel nuts are tight not loose.
8. Check whether the battery is fully charged before riding or whether the remaining
battery is enough to ride.
9. Whether the folding switch of the scooter rod is fastened.
How to use the charger correctly
1. When charging with the charger, the charging port of the scooter should be
connected first. (Please align the the output port of the charger with the scooter's
charging port).
2. The charging place should be far away from children, and ensure that the charging
environment is ventilated, dry, and away from flammable and explosive materials.
3. Please be sure to use the company's special charger for charging, otherwise it will
affect the life of the battery or damage the battery.
4. The maximum continuous
1 charging time shall not exceed 18 hours.
5. It is forbidden to connect the charger to the power supply without load.
6. After the charging is completed, you should first pull out the power plug before
pull out the plug of the scooter .
7. After the power is turned on, the red light indicates that the charging is in progress.
When the charger indicator turns to green, the charging is completed.
Safety instructions
1. This product is limited to one person, do not carry other people at the same time.
2. It’s better to wear safety helmets and other protective equipment when riding this
product, pay attention to riding safety.
3. Please practice in the flat and wide outdoor place with low traffic flow first, and
then drive on the road after you are proficient in the product.
4. Never ride this product in an unsafe or illegal place, and use it in accordance with
local traffic laws.
5. Do not turn off the power while riding the scooter.
6. Do not try to directly pass the steps with a gap of more than 5 cm, it may cause the
scooter to overturn, causing human injury or damage to the scooter.
For steps below 5 cm, try to avoid them. Try to ride on flat road.
7. Do not use this product in an environment below -5℃.
8. Keep your feet on the scooter as far as possible (and the support stand is retracted),
and pay attention to balancing your body's gravity.
9. When passing rough or uneven roads, please slow down and drive carefully.
10. Never ride scooter on the surface with oil or ice, beware of slipping, safety first.
11. The user must adjust the height of the product to an appropriate position, and all
parts that need to be locked must be locked, check it before riding, otherwise it will
cause injury or damage.
1
12. This product is waterproof, but not completely waterproof. Do not immerse the
product in deep water or be directly sprayed with water, as it may cause motor and
circuit failures.
13. Before riding, you must check and confirm that the brakes, frame, handlebars,
wheels, saddles and other components are securely locked to avoid accidents.
14. The electric scooter should avoid being placed in a place where the air is humid
and the temperature is too high as much as possible. Avoid prolonged sun exposure
and rain to avoid damage to the electrical components in the vehicle, resulting in
operation failure and accidents.
Regular Inspection & Maintenance
A: Check S: Adjust D: Replace L: Lubricate T: Tighten
Inspection Items 60 days 180days 360days
Whether the handlebar rotates and whether
S/T A/T A/L
the steering parts are loose or worn
Whether the tire is properly inflated and the
A A D
tire is worn
Front and rear axle gears, wheel axles are
T A/L A/L
deformed or worn
Whether the brake pad is worn
D D
Whether the rim is deformed or deflection
A A
Whether the frame and front fork are
A A
deformed or bruised
Is the braking effect good?
A A A
Whether the horn and headlights are
A A
working properly
Whether the charger or charging plug is
A A
damaged
Whether the normal tightening screws are
S S S
loose
Common Faults & Troubleshooting Methods
No. Specific failure Cause of issue Solution
conditions
The anti-theft device or key lock is Replace the anti-theft
The display damaged device or key lock
1 panel cannot
be turned on The battery voltage is too low Fully charge the battery
Blown fuse Replace fuse
Poor battery wiring Check and connect
Can be turned
2 The connection of the motor Check and connect
on but the
terminal is abnormal
motor does
not work The signal line of the panel is loose Check and connect
The wheels are flat To inflate
Insufficient
The battery is aged or damaged Replace the battery
cruising range
3 Charging is not full Check the charger and
battery power
Driving against the wind, many Driving on flat roads
hillsides, heavy weight
The charging plug is not plugged Check and clean the plug
The charger in
4 cannot be 1
charged The charger is damaged Replace the charger
The battery is damaged Replace or repair the
battery
When the fault cannot be Contact supplier or
Other eliminated according to the above repair station
5 problems guidelines
When the internal damage of the please do not open it
motor, controller, battery, etc. without authorization,
you may lose the
warranty
After-sales service
Part Name Service Term Warranty Approach
Motor 6 months Failure in normal use 6 months
warranty for
non-human damage
Battery 6 months Failure in normal use Normal attenuation
is not covered by
warranty
Instrument 6 months Quality issues 6 months
warranty for
accelerator non-human damage
Controller 6 months Quality issues 6 months
warranty for
non-human damage
Charger 6 months Quality issues Non-human damage
can be guaranteed
Trumpet 1 months No sound Non-human damage
can be guaranteed
Frame 6 months Desoldering, Non-human damage
non-artificial fracture can be guaranteed
Tire 1 months Air leakage Non-human damage
(non-artificial or can be guaranteed
pierced)
Shock-absorbing 6 months Performance failure Non-human damage
front fork can be guaranteed
Lamp pedal 3 months Performance failure Non-human damage
can be guaranteed
Power lock 1 months Non-human damage Non-human damage
failure can be guaranteed
Note: trade-in for the new one (within the warranty period)
No. What is not covered by the warranty
1 The warranty period has expired or no scooter purchase certificate
2 Commercial rental scooters are not warranted
3 The gifts are not covered by the warranty
4 Unauthorized modification, damage caused by replacement parts
5 The consumables of consumables are not guaranteed after one
month, and if the consumables are damaged and are not replaced
in time, the related parts will be damaged.
6 Improper maintenance of users or damage to parts caused by
collision damage, water ingress, burnout, overloaded use and
other expenses caused by abnormal riding are not warranted
7 Damage caused by force majeure factors such as natural disasters
will not be guaranteed
Thank you for reading this instruction manual
carefully, please pay attention
to the inspection and precautions before riding,
thank you for choosing our
products, and wish you a satisfied journey!
