Technical Data Sheet
Approved 46642;46662 1 46642 epoxy mastic ^(ValidationDate) 1
Penguard Midcoat M20 S
Product description
This is a two component polyamine cured epoxy coating. It is a micaceous iron oxide (MIO) pigmented, fast
drying, high solids, high build epoxy product. It offers good levelling and improved film appearance. Designed as
a mid coat in systems for new construction in atmospheric environments. Suitable in approved coating systems.
Typical use
Suitable for structural steel exposed to corrosive environments. Recommended for wind turbine towers,
refineries, power plants, buildings and mining equipment.
Other
Other variants available
Penguard Midcoat M20
Refer to separate TDS for each variant.
Colours
Light grey, off-white, RAL 7035, RAL 9001, RAL 9010, RAL 9018
Product data
Property Test/Standard Description
Solids by volume ISO 3233 77 ± 2 %
Gloss level (GU 60 °) ISO 2813 matt (0-35)
Flash point ISO 3679 Method 1 30 °C
Density calculated 1.6 kg/l
Region Regulation Test Standard VOC Value
China GB 30981-2020 Limit of harmful GB/T 23985-2009 8.3 167 g/l
substances of industrial protective coatings
The provided data is typical for factory produced products, subject to slight variation depending on colour.
Gloss description: According to Jotun Performance Coatings' definition.
Date of issue: 8 April 2024 Page: 1/5
This Technical Data Sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at [Link]
Technical Data Sheet
Penguard Midcoat M20 S
Film thickness per coat
Typical recommended specification range
Dry film thickness 100 - 250 μm
Wet film thickness 130 - 325 μm
Theoretical spreading rate 7.7 - 3.1 m²/l
For DFT below 100 µm more thinner should be added.
Surface preparation
Surface preparation summary table
Surface preparation
Substrate Minimum Recommended
Coated surfaces Clean, dry and undamaged compatible Clean, dry and undamaged compatible
coating coating
Optimum performance, including adhesion, corrosion protection, heat resistance and chemical resistance is
achieved with recommended surface preparation.
Application
Application methods
The product can be applied by
Spray: Use airless spray.
Brush: Recommended for stripe coating and small areas, care must be taken to achieve the
specified dry film thickness.
Product mixing ratio (by volume)
Penguard Midcoat M20 S Comp A 5 part(s)
Penguard Midcoat M20 S Comp B 1 part(s)
Date of issue: 8 April 2024 Page: 2/5
This Technical Data Sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at [Link]
Technical Data Sheet
Penguard Midcoat M20 S
Thinner/Cleaning solvent
Thinner: Jotun Thinner No. 17
Thinning is not normally required. Consult the local representative for advice during application in extreme
conditions. Do not thin more than allowed by local environmental legislation.
Guiding data for airless spray
Nozzle tip (inch/1000): 17 -27
Pressure at nozzle (minimum): 150 bar/2100 psi
Drying and Curing time
Substrate temperature 5 °C 10 °C 23 °C 40 °C
Surface (touch) dry 8h 5h 2h 1h
Walk-on-dry 24 h 12 h 5h 2h
Dry to over coat, minimum 24 h 12 h 5h 2h
Dried/cured for service 14 d 10 d 7d 3d
For maximum overcoating intervals, refer to the Application Guide (AG) for this product.
Drying and curing times are determined under controlled temperatures and relative humidity below 85 %, and
at average of the DFT range for the product.
Surface (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal
tackiness.
Walk-on-dry: Minimum time before the coating can tolerate normal foot traffic without permanent marks,
imprints or other physical damage.
Dry to over coat, minimum: The recommended shortest time before the next coat can be applied.
Dried/cured for service: Minimum time before the coating can be permanently exposed to the intended
environment/medium.
Induction time and Pot life
Paint temperature 23 °C
Pot life 1h
Date of issue: 8 April 2024 Page: 3/5
This Technical Data Sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at [Link]
Technical Data Sheet
Penguard Midcoat M20 S
Heat resistance
Temperature
Continuous Peak
Dry, atmospheric 120 °C 140 °C
Peak temperature duration max. 1 hour.
The temperatures listed relate to retention of protective properties. Aesthetic properties may suffer at these
temperatures.
Product compatibility
Depending on the actual exposure of the coating system, various primers and topcoats can be used in
combination with this product. Some examples are shown below. Contact Jotun for specific system
recommendation.
Previous coat: inorganic zinc silicate shop primer, zinc epoxy, epoxy
Subsequent coat: polyurethane, epoxy, acrylic
Packaging (typical)
Volume Size of containers
(litres) (litres)
Penguard Midcoat M20 S Comp A 15 20
Penguard Midcoat M20 S Comp B 3 3
The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary
due to local regulations.
Storage
The product must be stored in accordance with national regulations. Keep the containers in a dry, shaded, cool,
well-ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed.
Handle with care.
Shelf life at 23 °C
Penguard Midcoat M20 S Comp A 24 month(s)
Penguard Midcoat M20 S Comp B 24 month(s)
In some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf
life, thereafter the paint quality is subject to re-inspection.
Date of issue: 8 April 2024 Page: 4/5
This Technical Data Sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at [Link]
Technical Data Sheet
Penguard Midcoat M20 S
Caution
This product is for professional use only. The applicators and operators shall be trained, experienced and have
the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun's technical
documentation. Applicators and operators shall use appropriate personal protection equipment when using this
product. This guideline is given based on the current knowledge of the product. Any suggested deviation to suit
the site conditions shall be forwarded to the responsible Jotun representative for approval before commencing
the work.
Health and safety
Please observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do
not inhale spray mist. Avoid skin contact. Spillage on the skin should immediately be removed with suitable
cleanser, soap and water. Eyes should be well flushed with water and medical attention sought immediately.
Colour variation
When applicable, products primarily meant for use as primers or antifoulings may have slight colour variations
from batch to batch. Such products and epoxy based products used as a finish coat may chalk when exposed to
sunlight and weathering.
Colour and gloss retention on topcoats/finish coats may vary depending on type of colour, exposure
environment such as temperature, UV intensity etc., application quality and generic type of paint. Contact your
local Jotun office for further information.
Disclaimer
The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and
practical experience. Jotun's products are considered as semi-finished goods and as such, products are often
used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the product
itself. Minor product variations may be implemented in order to comply with local requirements. Jotun reserves
the right to change the given data without further notice.
Users should always consult Jotun for specific guidance on the general suitability of this product for their needs
and specific application practices.
If there is any inconsistency between different language issues of this document, the English (United Kingdom)
version will prevail.
Date of issue: 8 April 2024 Page: 5/5
This Technical Data Sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at [Link]
