INTERNATIONAL ISO
STANDARD 582
Third edition
1995-05-15
AMENDMENT 1
2013-07-01
Rolling bearings — Chamfer
dimensions — Maximum values
AMENDMENT 1
Roulements — Dimensions des arrondis — Valeurs maximales
AMENDEMENT 1
iTeh STANDARD PREVIEW
([Link])
ISO 582:1995/Amd 1:2013
[Link]
357d7ac34106/iso-582-1995-amd-1-2013
Reference number
ISO 582:1995/Amd.1:2013(E)
© ISO 2013
ISO 582:1995/Amd.1:2013(E)
iTeh STANDARD PREVIEW
([Link])
ISO 582:1995/Amd 1:2013
[Link]
357d7ac34106/iso-582-1995-amd-1-2013
COPYRIGHT PROTECTED DOCUMENT
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@[Link]
Web [Link]
Published in Switzerland
ii © ISO 2013 – All rights reserved
ISO 582:1995/Amd.1:2013(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International
Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies
casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
Amendment 1 to ISO 582:1995 was prepared by Technical Committee ISO/TC 4, Rolling bearings,
Subcommittee SC 4, Tolerances, tolerance definitions and symbols (including GPS).
iTeh STANDARD PREVIEW
([Link])
ISO 582:1995/Amd 1:2013
[Link]
357d7ac34106/iso-582-1995-amd-1-2013
© ISO 2013 – All rights reserved iii
iTeh STANDARD PREVIEW
([Link])
ISO 582:1995/Amd 1:2013
[Link]
357d7ac34106/iso-582-1995-amd-1-2013
ISO 582:1995/Amd.1:2013(E)
Rolling bearings — Chamfer dimensions — Maximum values
AMENDMENT 1
Page 1, Normative references
Replace the reference to ISO 355:1977 with the following:
ISO 355, Rolling bearings — Tapered roller bearings — Boundary dimensions and series designations
Page 4, Clause 5
Replace Table 4 with the following new table, thus adding new rows with first column values of 0,5, 3,3,
7 and 8 for rs min, or r1s min.
iTeh STANDARD PREVIEW
([Link])
ISO 582:1995/Amd 1:2013
[Link]
357d7ac34106/iso-582-1995-amd-1-2013
© ISO 2013 – All rights reserved 1
ISO 582:1995/Amd.1:2013(E)
Dimensions in millimetres
rs min or r1s min1) d or D rs max or r1s max
Directions
radial axial
d or D ≤ 40 0,7 1,4
0,3
d or D > 40 0,9 1,6
d or D ≤ 40 1,1 1,7
0,5
d or D > 40 1,2 1,9
d or D ≤ 40 1,1 1,7
0,6
d or D > 40 1,3 2
d or D ≤ 50 1,6 2,5
1
d or D > 50 1,9 3
d or D ≤ 120 2,3 3
1,5 120 < d (or D) ≤ 250 2,8 3,5
d or D > 250 3,5 4
d or D ≤ 120 2,8 4
2 120 < d (or D) ≤ 250 3,5 4,5
d or D > 250 4 5
d or D ≤ 120 3,5 5
2,5 120 < d (or D) ≤ 250 4 5,5
d or D > 250 4,5 6
iTeh STANDARD
d or D ≤ 120 PREVIEW
4 5,5
120 < d (or D) ≤ 250 4,5 6,5
3 ([Link])
250 < d (or D) ≤ 400 5 7
d or D > 400 5,5 7,5
d orISO
D ≤582:1995/Amd
120 1:20134,3 6,3
120 < d (or D) ≤ 250 4,8 6,8
[Link]
3,3
250 < d (or D) ≤ 400
357d7ac34106/iso-582-1995-amd-1-2013 5,3 7,3
d or D > 400 5,8 7,8
d or D ≤ 120 5 7
120 < d (or D) ≤ 250 5,5 7,5
4
250 < d (or D) ≤ 400 6 8
d or D > 400 6,5 8,5
d or D ≤ 180 6,5 8
5
d or D > 180 7,5 9
d or D ≤ 180 7,5 10
6
d or D > 180 9 11
d or D ≤ 180 10 12,5
7
d or D > 180 11,5 13,5
d or D ≤ 180 12,5 15,5
8
d or D > 180 14,5 17,5
1) See Clause 5 for maximum shaft and housing fillet radii.
2 © ISO 2013 – All rights reserved
iTeh STANDARD PREVIEW
([Link])
ISO 582:1995/Amd 1:2013
[Link]
357d7ac34106/iso-582-1995-amd-1-2013
ISO 582:1995/Amd.1:2013(E)
iTeh STANDARD PREVIEW
([Link])
ISO 582:1995/Amd 1:2013
[Link]
357d7ac34106/iso-582-1995-amd-1-2013
ICS 21.100.20
Price based on 2 pages
© ISO 2013 – All rights reserved
