INTERNATIONAL ISO
STANDARD 4753
Second edition
1999-12-01
Fasteners — Ends of parts with external
ISO metric thread
Éléments de fixation — Extrémités des éléments à filetage extérieur
métrique ISO
iTeh STANDARD PREVIEW
([Link])
ISO 4753:1999
[Link]
9694-d56683090d11/iso-4753-1999
A Reference number
ISO 4753:1999(E)
ISO 4753:1999(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
International Standard ISO 4753 was prepared by Technical Committee ISO/TC 2, Fasteners, Subcommittee SC 7,
Reference Standards for fasteners (mainly covering terminology, dimensioning, sizes and tolerancing).
This second edition cancels and replaces the first edition (ISO 4753:1983) which has been technically revised.
iTeh STANDARD PREVIEW
([Link])
ISO 4753:1999
[Link]
9694-d56683090d11/iso-4753-1999
© ISO 1999
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet iso@[Link]
Printed in Switzerland
ii
INTERNATIONAL STANDARD © ISO ISO 4753:1999(E)
Fasteners — Ends of parts with external ISO metric thread
1 Scope
This International Standard specifies the form and dimensions of ends of parts with external ISO metric screw
thread (e.g., bolt and screw ends) recommended for use. They apply to standardized or non-standardized threaded
parts if they are specified at the time of order.
iTeh STANDARD PREVIEW
For each end type a symbol is specified and it is recommended to use these symbols when specifying one of the
ends for threaded fasteners.
([Link])
ISO 4753:1999
2 Normative references
[Link]
9694-d56683090d11/iso-4753-1999
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this International Standard. For dated references, subsequent amendments to, or revisions of, any of these
publications do not apply. However, parties to agreements based on this International Standard are encouraged to
investigate the possibility of applying the most recent editions of the normative documents indicated below. For
undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC
maintain registers of currently valid International Standards.
ISO 225:1983, Fasteners — Bolts, screws, studs and nuts — Symbols and designations of dimensions.
ISO 4027:1993, Hexagon socket set screws with cone point.
3 Dimensions
See Figures 1 and 2 and Tables 1 to 4.
Symbols and designations of dimensions are specified in ISO 225.
1
ISO 4753:1999(E) © ISO
3.1 Ends which are included in the nominal length of the fastener
As-rolled end (RL) Chamfered end (CH) Rounded end (RN)
Flat point (FL) Short dog point (SD) Long dog point (LD)
Cone point (CN) Truncated cone point (TC) Cup point (CP)
iTeh STANDARD PREVIEW
([Link])
ISO 4753:1999
[Link]
9694-d56683090d11/iso-4753-1999
Scrape point (SC)
re ª 1,4d v = 0,5d ± 0,5 mm ln ⭐ 5P
dn = d ⫺ 1,6P lk ⭐ 3P ln ⫺ lk ⭓ 2P (P is the pitch of thread)
NOTE 1 l is the nominal length of the fastener.
NOTE 2 Incomplete thread u ⭐ 2 P
NOTE 3 The 45° angle for the ends FL, SD, LD and CP applies only to the portion of the point below the root diameter of the
thread.
a End may be dimpled. c Slight radius
b Maximum diameter at the minor thread diameter. d 120° ± 2° for short length screws; see product standard, e.g. ISO 4027.
Figure 1
2
© ISO ISO 4753:1999(E)
Table 1 — Dimensions
Dimensions in millimetres
Thread diameter dp dt c dz z1 z2
+ IT14 d + IT14 d
da h14 b h16 h14 0 0
1,6 0,8 — 0,8 0,4 0,8
1,8 0,9 — 0,9 0,45 0,9
2 1 — 1 0,5 1
2,2 1,2 — 1,1 0,55 1,1
2,5 1,5 — 1,2 0,63 1,25
3 2 — 1,4 0,75 1,5
3,5 2,2 — 1,7 0,88 1,75
4 2,5 — 2 1 2
4,5 3 — 2,2 1,12 2,25
5 3,5 — 2,5 1,25 2,5
6 4 1,5 3 1,5 3
7 5 2 4 1,75 3,5
8 5,5 2 5 2 4
10 7iTeh STANDARD
2,5 PREVIEW
6 2,5 5
12 8,5 ([Link])
3 8 3 6
14 10 4 8,5 3,5 7
16 12 4
ISO 4753:1999 10 4 8
[Link]
18 13 5
9694-d56683090d11/iso-4753-1999 11 4,5 9
20 15 5 14 5 10
22 17 6 15 5,5 11
24 18 6 16 6 12
27 21 8 — 6,7 13,5
30 23 8 — 7,5 15
33 26 10 — 8,2 16,5
36 28 10 — 9 18
39 30 12 — 9,7 19,5
42 32 12 — 10,5 21
45 35 14 — 11,2 22,5
48 38 14 — 12 24
52 42 16 — 13 26
a For sizes ⬍ M1,6 dimensions and tolerances should be agreed as suitable.
b For nominal dimensions ⭐ 1 mm tolerance field h13 applies.
c For threads ⭐ M5 no flat part on the cone required; the point may be slightly rounded.
+ IT13
d For nominal dimensions ⭐ 1 mm tolerance field 0 applies.
3
ISO 4753:1999(E) © ISO
3.2 Ends which are added to the specified nominal length of the fastener
Pilot point, flat (PF) Pilot point with truncated cone (PC)
NOTE 1 Incomplete thread u ⭐ 2P
NOTE 2 The 20° angle applies only to the portion of the point below the root diameter of the thread.
a End may be dimpled.
iTeh STANDARD
Figure 2
PREVIEW
([Link])
ISO 4753:1999
Table [Link]
2 — Dimensions for flat pilot points; coarse pitch thread
9694-d56683090d11/iso-4753-1999 Dimensions in millimetres
Thread size M4 M5 M6 M8 M10 M12 M14 M16 M20 M24
dx a max. 2,9 3,8 4,5 6,1 7,8 9,4 11,1 13,1 16,3 19,6
min. 2,7 3,6 4,3 5,9 7,6 9,1 10,8 12,8 15,9 19,2
+ IT17
z3 0 2 2,5 3 4 5 6 7 8 10 12
a If, in special cases, a smaller diameter is required this must be agreed separately.
Table 3 — Dimensions for pilot points with truncated cone; coarse pitch thread
Dimensions in millimetres
Thread size M4 M5 M6 M8 M10 M12 M14 M16 M20 M24
dx a max. 2,9 3,8 4,5 6,1 7,8 9,4 11,1 13,1 16,3 19,6
min. 2,7 3,6 4,3 5,9 7,6 9,1 10,8 12,8 15,9 19,2
+ IT17
z4 0 2 2,5 3 4 5 6 7 8 10 12
z5 max. 1,0 1,50 2 2,5 3,0 3,5 4 4,5 5 6
min. 0,5 0,75 1 1,5 1,5 2,0 2 2,5 3 4
a If in special cases a smaller diameter is required this must be agreed separately.
4
© ISO ISO 4753:1999(E)
Table 4 — Dimensions for pilot points with truncated cone; fine pitch thread
Dimensions in millimetres
Thread size M8 × 1 M10 × 1 M12 × 1,5 M14 × 1,5 M16 × 1,5
dx max. 6,3 8,0 9,6 11,40 13,50
min. 6,08 7,78 9,38 11,13 13,23
+ IT17
z4 0 4 5 6 7 8
z5 max. 2,5 3 3,5 4 4,5
min. 1,5 1,5 2 2 2,5
iTeh STANDARD PREVIEW
([Link])
ISO 4753:1999
[Link]
9694-d56683090d11/iso-4753-1999
5
ISO 4753:1999(E) © ISO
iTeh STANDARD PREVIEW
([Link])
ISO 4753:1999
[Link]
9694-d56683090d11/iso-4753-1999
ICS 21.060.01
Price based on 5 pages
