Piping Material Specification

01CS610 Rev: 2.0, Date: Sep 2016

SERVICE: Utility Air MATERIAL: Carbon Steel

RATING: Class 150, ASME B16.5 DESIGN CODE: ASME B31.3

TEMPERATURE LIMIT: -20°F to 350°F X-RAY: 5% Random

CORROSION 0.0625 inch STRESS RELIEF: None

ALLOWANCE:

PRESSURE - TEMPERATURE RATINGS (For NPS 1/2 through NPS 24)

TEMP °F -20 to 100 200 300 400
PSIG 285 260 230 200

(Full flange ratings per latest approved editions of ASME B16.5)

ITEM NOTES NPS Range SCH / RAT ENDS DESCRIPTION MDMT/CODE
PIPE Start End
181 ½" 1" 80 T&C CS, SMLS, ASTM A106 Gr B, Galv -20°F

1½" 2" 80 T&C CS, SMLS, ASTM A106 Gr B, Galv -20°F

118 3" 8" STD BE CS, SMLS, ASTM A53 Gr. B -20°F

NIPPLES Start End

Pipe 181 ½" 1" 80 TBE CS, SMLS, ASTM A106 Gr B, Galv

Pipe 1½" 2" 80 TBE CS, SMLS, ASTM A106 Gr B, Galv

Swage 181 ½" 1" 80 TBE CS, SMLS, ASTM A106 Gr B, Galv

Swage 1½" 2" 80 TBE CS, SMLS, ASTM A106 Gr B, Galv

FITTINGS Start End

BW Cap 3" 8" STD BW CS, ASTM A234 WPB

BW Conc Red 3" 8" STD BW CS, ASTM A234 WPB

BW Ecc Red 3" 8" STD BW CS, ASTM A234 WPB

BW LR 45 Ell 3" 8" STD BW CS, ASTM A234 WPB

BW LR 90 Ell 3" 8" STD BW CS, ASTM A234 WPB

BW Red Tee 3" 8" STD BW CS, ASTM A234 WPB

BW Tee 3" 8" STD BW CS, ASTM A234 WPB

Compression 41, ½" 4 LOKRING permanent type (non-separable)

122, compression fittings, CS, MAS3000 series
283
Plug ½" 1½" THRD CS, ASTM A105, Solid Bar Stock, Galvanized Long Style

SCRD 45 Ell ½" 2" 3000 SCRD CS, ASTM A105, Galvanized

SCRD 90 Ell ½" 2" 3000 SCRD CS, ASTM A105, Galvanized

SCRD Cap ½" 2" 3000 SCRD CS, ASTM A105, Galvanized

SCRD Full Coupling ½" 2" 3000 SCRD CS, ASTM A105, Galvanized

SCRD Red Tee ½" 1½" 3000 SCRD CS, ASTM A105, Galvanized

SCRD Tee ½" 2" 3000 SCRD CS, ASTM A105, Galvanized

SCRD Union ½" 2" 3000 SCRD CS, ASTM A105, Galv (ground joint)

Threadolet ½" 2" 3000 SCRD CS, ASTM A105, Galvanized

Weldolet 3" 3" STD BW CS, ASTM A105

PRIVATE/PROPRIETARY: Not for use or disclosure outside Enterprise Products Company and/or its affiliates Page 1 of 6
without express, prior, written permission.
 Piping Material Specification
01CS610 Rev: 2.0, Date: Sep 2016

ITEM NOTES NPS Range SCH / RAT ENDS DESCRIPTION MDMT/CODE

VALVES Start End
Ball Flg: Qtr Turn 2" 8" Class 150 RF CS, Forged or Cast, Full Port, Trunnion (-20°F to VB-014F
325°F)

Ball Flg: Rising Stem 1" 8" Class 150 RF CS, Cast, ASTM A216 WCC, Full Port VB-016F

Ball Flg: Rising Stem 2" 8" Class 150 RF CS, Cast, ASTM A216 WCC, Reduced Port VB-016

Ball SCRD: Qtr Turn ½" 2" Class 1500 SCRD CS, Forged or Cast, Three-piece Bolted Body KSB-151

Check Flg 2" 8" Class 150 RF CS, Cast, ASTM A216 WCB, Swing Check VC-016

Check SCRD ½" 2" Class 800 SCRD CS, Forged, ASTM A105, Piston Check, Spring KSCP-081
Loaded

Check SCRD 228 1" 1" 3000 CWP SCRD 316 SS, Cracking Check, Spring Loaded KSCP-305SS

Check: Wafer, 2" 24" Class 150 RF CS, Cast, ASTM A216 WCB, Double-flanged VCW-014DF
Double-flanged
Check: Wafer, Lug- 2" 24" Class 150 RF CS, Cast, ASTM A216 WCB, Lug-type, Drilled VCW-014LU
type Through

Gate Flg 231 ¾" 2" Class 150 RF CS, Forged, ASTM A105, Wedge Gate V-017

Gate Flg 260 2" 8" Class 150 RF CS, Cast, ASTM A216 WCB, Wedge Gate V-016

Gate SCRD 231 ½" 2" Class 800 SCRD CS, Forged, ASTM A105, Reduced Port, Wedge KS-081
Gate

Gate SCRD ½" 2" Class 800 SCRD CS, Forged, ASTM A105, Full Port, Wedge Gate KS-081F

Globe Flg ½" 2" Class 150 RF CS, Forged, ASTM A105 VG-017

Globe Flg 2" 8" Class 150 RF CS, Cast, ASTM A216 WCB VG-016

Globe SCRD ½" 2" Class 800 SCRD CS, Forged, ASTM A105 KSG-081

FLANGES Start End

½" 2" Class 150 RFSE ASTM A105, galvanized

3" 8" Class 150 RFWN ASTM A105, bore to match pipe

Blind ½" 8" Class 150 RFBLD CS, ASTM A105, ASME B16.5

ORIFICE FLANGE Start End

1" 8" Class 300 RFWN CS, ASTM A105, per ANSI B16.36, bore to match
pipe, ½" scrd taps

STUD BOLTS Start End

½" 8" PTFE Coated, ASTM A193 B7 with two ASTM A194
2H heavy hex nuts each

GASKETS Start End

½" 8" Class 150 1/8" thick Spiral-Wound Type 304 SS, Flexible
graphite filler, ASME B16.20 (Gray Stripe), Flexitallic
Style "CG" or Company approved equal

1" 8" Class 300 1/8" thick Spiral-Wound Type 304 SS, Flexible
graphite filler, ASME B16.20 (Gray Stripe), Flexitallic
Style "CG" or Company approved equal

SEALANT Start End

Pipe Thread Sealant 294 450°F and less use Full Density PTFE tape or an
equal PTFE sealant compound.

MISCELLANEOUS Start End

Figure-8 Blind ½" 8" Class 150 RF CS, ASTM A515 Gr. 70, ASME B16.48, face finish
per ASME B16.5

Paddle Blind ½" 8" Class 150 RF CS, ASTM A515 Gr. 70, ASME B16.48, face finish
per ASME B16.5

PRIVATE/PROPRIETARY: Not for use or disclosure outside Enterprise Products Company and/or its affiliates Page 2 of 6
without express, prior, written permission.
 Piping Material Specification
01CS610 Rev: 2.0, Date: Sep 2016

ITEM NOTES NPS Range SCH / RAT ENDS DESCRIPTION MDMT/CODE

MISCELLANEOUS Start End
Paddle Spacer ½" 8" Class 150 RF CS, ASTM A515 Gr. 70, ASME B16.48, face finish
per ASME B16.5

PRIVATE/PROPRIETARY: Not for use or disclosure outside Enterprise Products Company and/or its affiliates Page 3 of 6
without express, prior, written permission.
 Piping Material Specification
01CS610 Rev: 2.0, Date: Sep 2016

NOTES
41 Do not use where crevice corrosion will occur.

107 Hot Taps not permitted in this service.

118 Instrument bridles require S/80 min.

122 LOKRING connections shall be made in accordance with procedures established by LOKRING under the supervision of a
LOKRING representative or personnel qualified by a LOKRING representative.

181 Sch. 160 Requirements:

A. High point vents, low point drains, and instrument connections to be S/160 minimum thru block valve.
B. Process piping to be installed as S/160 minimum to first valve or fitting (control valve bypasses excluded).
C. All swages required for the above applications to be XXH minimum.

228 This valve for Air and Nitrogen Injection Line (when specified).

231 This valve is suitable for vents, drains, and valved instrument connections.

240 To be used for specific UOP requirements only.

247 To use this specification, the Fluid Service Temperature must exceed the Pipe MDMT. If for certain pipe sizes, the Pipe
MDMT is greater than the Fluid Service Temperature, then another piping specification that meets the Pipe MDMT is to be
selected. Pipe MDMT is to be determined from ASME B31.3 Table 323.2.2A and Figures 323.2.2A and 323.2.2B. Fluid
Service Temperature (i.e. System Design Temperature (Tdesign)) is defined as the lesser of the system operating
temperature (including any design margin) or the local minimum ambient temperature (i.e. for cases where a pressurized
non-flowing system can essentially equalize at the ambient conditions). The minimum ambient temperature is to be
determined by Project Engineering and be a part of the Project Job Scope.

260 Use only if shown on P&ID.

283 For vibrating service, Lokring fitting installations must be approved in advance by the Enterprise Equipment Reliability
Group.

294 PTFE tape shall comply with Federal STD. A-A-58092, (formerly MIL-T-27730A). PTFE compound shall be certified to the
latest applicable ANSI and/or Federal standards.

PRIVATE/PROPRIETARY: Not for use or disclosure outside Enterprise Products Company and/or its affiliates Page 4 of 6
without express, prior, written permission.
 Piping Material Specification
01CS610 Rev: 2.0, Date: Sep 2016

BRANCH CONNECTION LEGEND

NOTES: 107
T Tee or Reducing Tee
TOL Thread-o-let
W Weld-o-let

BRANCH CONNECTION TABLE

BRANCH SIZE
HEADER ½" ¾" 1" 1½" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24" 30" 36" 42" 48"
SIZE
¾" T T

1" T T T

1½" T T T T

2" T T T T T

3" TOL TOL TOL TOL TOL T

4" TOL TOL TOL TOL TOL T T

6" TOL TOL TOL TOL TOL T T T

8" TOL TOL TOL TOL TOL W T T T

½" ¾" 1" 1½" 2" 3" 4" 6" 8"

PRIVATE/PROPRIETARY: Not for use or disclosure outside Enterprise Products Company and/or its affiliates Page 5 of 6
without express, prior, written permission.
 Piping Material Specification
01CS610 Rev: 2.0, Date: Sep 2016

ATTACHMENT REVISION LOG/RECORD

Revision Location of Type of Change Reason For Change Publish Date
Number Change
Revision 0.0 N/A N/A N/A Publish Date:
27 Mar 2011

Revision 0.1 Item: Valves Corrected Typo KSB-154 was changed to KSB-151 Publish Date:
26 Sep 2012

Item: Valves Corrected Typo VC-033SS was changed to KSCP-305SS

Revision 1.0 Item: Fittings Addition Added LOKRING compression fittings and applicable notes. Publish Date:
and Notes 06 Oct 2015

Item: Branch Revision Removed the note that says, "When two side connections on an
Connections instrument bridle are too close for two 3" reducing tee connections, a
4" bridle with o-let connections may be used."

Complete Update Numerous formatting changes, including renumbering and

Specification standardization of notes, were made due to the conversion of the
piping specifications into the "Pipe Solutions Database."

Revision 2.0 Item: Valves Revision The upper size range of small bore forged, SW or SCRD valves was Publish Date:
revised up to 2". 29 Sep 2016

Item: Valves Update Valve descriptions and size ranges have been evaluated and
standardized to agree with the valve specifications.

Item: Valves Update The size range was updated for all rising stem ball valves.

Item: Valves Addition Added valve line items for Type 'A' short face-to-face, Double-flanged
and Lug-type check valves, as defined by API 594.

Item: Valves Deletion Removed wafer-type (no lugs) check valve, VC-014.

Item: Flanges Addition A blind flange line item was added.

Item: Stud Revision ASTM A193 B7 plain bolts were revised to ASTM A193 B7 PTFE
Bolts coated.

Item: Gaskets Addition A Class 300 gasket line item was added for orifice flanges.

Item: Sealant, Revision The description for "Pipe Thread Sealant" was revised and a reference
Notes note was added to provide clear guidance when specifying pipe thread
sealants.

Item: Addition Added line items for Figure-8 Blinds, Paddle Blinds, and Paddle
Miscellaneous Spacers per ASME B16.48.

PRIVATE/PROPRIETARY: Not for use or disclosure outside Enterprise Products Company and/or its affiliates Page 6 of 6
without express, prior, written permission.