Cylindrical Type Tool Setter for Small CNC Machining Centers
TM26 12 / 20 Contact Type
Tool setters for small CNC machining centers are used for
precise blade positioning, and detection of the wear and
breakage.
12 20
Standard specifications unit:mm Precautions
Product name TM26 Although a protective cover is provided with the sensor, an
Contact diameter 12 20 extra cover is needed separately to prevent high pressure
coolant or heavy cuttings from entering inside and
Stationary type
accumulating in the body.
Surface finishing Grinding 4s
Rubber materials used in products are applicable to
Contact material Tungsten carbide water-soluble coolants and alkaline liquids. (Refer to P5-4)
Contact structure NC (Normally closed)
Output mode NO (Normally open) Precautions statement for Tool Setters ……… P2-3
Pretravel Approx. 0 How to replace Air Blow Pipe …………………… P2-4
Stroke 5 Precautions for sensor connecting …………… P5-1
Cable options ……………………………………… P5-2
Repeatability 0.003 (Recommended
speed of 50 - 200mm/min)
operating
Technical guide …………………………………… P5-3
Contact life time 3 million
IP67
Contact force 2.5N (Installation position : Vertical)
DC5V - DC24V 10mA (Max20mA)
Contact rating
resistance load
Oil resistant 4.8 / 6 cores
Cable
Tensile strength 30N, Minimum bending R7
LED lamp Default : LED OFF / Operating : LED ON
Over travel signal (built-in microswitch)
NC (Normally closed)
Output mode
"About 2.5mm from skip signal"
Contact rating DC24V 100mA resistance load
2-17 No.C4-1E
[Link]
12 Contact Type
Outer dimensions
TM26B-112
Circuit diagram
Built-in I/F unit (Standard)
RED DC24V
2- 4.5
LED
BROWN NO (Inverted-output)
I/F Photo Mos
NC ORANGE AC / DC
GRAY 0V
NC
40
GREEN
Over travel signal
BLUE
Power supply voltage : DC24V
Power consumption : 10mA
Output capacity : DC60V 100mA (Resistance load)
AC60V 100mA (Peak value)
0.01/12 A Contact 12 500mW (Max)
Air Blow Pipe I/F Unit Not Required (Optional)
LED
NC
ORANGE +
Output
33 BLACK −
Hose Nipple
(68)
NC
65
YELLOW
Over travel signal
32
LED Lamp GREEN
30 Cable : 5 / 4cores
17
8
50 6.5 22
A
81 42 528 1442
Specification sheet E-mail : touchsensor@[Link]
Please send us your inquiry by fax/e-mail after copying this page, and filling in necessary infomation. Sample :
Optional specifications (Bold:Standard) Date:(mm,dd,yy)
Output mode NO : Normally open NC : Normally closed
I/F unit Built-in Not required (Contact structure = Output mode)
Cable options (1m/unit)
Length / Protective cable m / Unnecessary Protective tube m (Upper limit :15m)
Connector (Refer to P5-2) Not required Connector
Machine side cable option Length m
from connector (if desired) Protective cable Not required Protective tube m (Upper limit :15m)
Company : Ordering and Inquiries
[Link] [Link] [Link] [Link]
Dept. / Title : OK! /Metrol
Customer name :
or or or
E-mail E-mail E-mail Placement
Address : of order
T24E-04-19
Tel : Fax : Send the drawing(s)
Select/confirm the
Metrol sends the
quote,and the
of specific model
Fill out the specifi- based on spec sheet specific model by customer places the
the customer.
E-mail : cation sheet and
send to Metrol.
received. order for the same.
E-mail to : touchsensor@[Link]
Other (if any) : Download PDF sheet : [Link]
- Copy this page and use repeatedly -
No.C4-1E
2-18
[Link]
20 Contact Type
Outer dimensions
TM26D-120
Circuit diagram
Built-in I/F unit (Standard)
2- 4.5
RED DC24V
LED
BROWN NO (Inverted output)
I/F Photo Mos
NC ORANGE AC / DC
GRAY 0V
40
NC
GREEN
Over travel signal
BLUE
Power supply voltage : DC24V
Power consumption : 10mA
Output capacity : DC60V 100mA (Resistance load)
0.01/20 A Contact 20 AC60V 100mA (Peak value)
500mW (Max)
Air Blow Pipe I/F Unit Not Required (Optional)
LED
Hose Nipple NC
ORANGE +
Output
33 −
BLACK
(70)
67
NC
YELLOW
Over travel signal
32
LED Lamp GREEN
30 Cable : 5 / 4cores
17
8
22
A 50 6.5
81 42 528 1442
Specification sheet E-mail : touchsensor@[Link]
Please send us your inquiry by fax/e-mail after copying this page, and filling in necessary infomation. Sample :
Optional specifications (Bold:Standard) Date:(mm,dd,yy)
Output mode NO : Normally open NC : Normally closed
I/F unit Built-in Not required (Contact structure = Output mode)
Cable options (1m/unit)
Length / Protective cable m / Not required Protective tube m (Upper limit :15m)
Connector (Refer to P5-2) Not required Connector
Machine side cable option Length m
from connector (if desired) Protective cable Not required Protective tube m (Upper limit :15m)
Company : Ordering and Inquiries
[Link] [Link] [Link] [Link]
Dept. / Title : OK! /Metrol
Customer name :
or or or
E-mail E-mail E-mail Placement
Address : of order
T24E-04-19
Tel : Fax : Send the drawing(s)
Select/confirm the
Metrol sends the
quote,and the
of specific model
Fill out the specifi- based on spec sheet specific model by customer places the
the customer.
E-mail : cation sheet and
send to Metrol.
received. order for the same.
E-mail to : touchsensor@[Link]
Other (if any) : Download PDF sheet : [Link]
- Copy this page and use repeatedly -
2-19 No.C4-1E
