ME DISPLAYS

SPECIFICATIONS

FOR

LCD MODULE

CCM2040

MICRO ELECTRONICS CORPORATION

3375 Scott Blvd. Suite 222 Santa Clara CA 95054
Tel: 408-988-1101 Fax: 408-988-7626
Email: micro@[Link]
Http://[Link]
ME DISPLAYS CCM2040
20 x 4 lines Character

• FEATURES
Number of Characters 20 characters x 4 lines
Display Font 5 x 8 dots
Built-in Controller HD44780 or Comp
Input Data 4 Bits or 8-Bits Interface
Power Supply +5 V Single Power
Duty Cycle 1/16 Duty
Options EL/LED Backlight, TN/STN

• MECHANICAL PARAMETERS
Module Size 98.0W x 60.0H x 11.0T mm
Module Size with LED Backlight 98.0W x 60.0H x 12.7T mm
Viewing Area Size 76.0W x 25.2H mm
Dot Size 0.60 x 0.60 mm
Dot Pitch 0.65 x 0.65 mm

• ABSOLUTE MAXIMUM
Item Symbol Min. Max Unit
Power Supply for Logic Vdd -0.3 +7.0 V
Power Supply for LCD Drive Vlcd 0 13.5 V
Input Voltage Vi Vss Vdd V
Operating Temperature Ta 0 +50 C
Storage Temperature Tstg -20 +70 C

• ELECTRICAL CHARACTERISTICS
(Vdd=5.0V ± 5%, Ta=25C)
Item Symbol Conditions Min Typ Max U
Power Supply for Logic Vdd -- 4.5 -- 5.5 V
Op. Voltage for LCD Vdd-Vo -- -- 5.0 -- V
Input “High” Voltage Vih -- 2.2 -- Vdd V
Input “Low” Voltage Vil -- -0.3 -- 0.6 V
Output “High” Voltage Voh - Ioh = 0.2mA 2.4 -- -- V
Output “Low” Voltage Vol Iol = 1.2mA -- -- 0.4 V
Power Supply Current Idd Vdd = 5.0V -- 1.0mA 3.0 mA

Micro Electronics Corp Http://[Link]

ME DISPLAYS CCM2040
20 x 4 lines Character

• PIN ASSIGNMENT

No. Symbol Level Pin Description Function

1 Vss -- Ground 0V
2 Vdd -- Supply Voltage for Logic 5V
3 Vo -- LCD Contrast Adjust By User
4 RS H/L Register Select H: Data, L: Instruction Code
5 R/W H/L Read / Write H: Data Read, L: Data Write
6 E H, HL Enable Enable Signal
7 DB0 H/L Data Bit 0 8-Bit Interface
8 DB1 H/L Data Bit 1 8-Bit Interface
9 DB2 H/L Data Bit 2 8-Bit Interface
10 DB3 H/L Data Bit 3 8-Bit Interface
11 DB4 H/L Data Bit 4 4 or 8-Bit Interface
12 DB5 H/L Data Bit 5 4 or 8-Bit Interface
13 DB6 H/L Data Bit 6 4 or 8-Bit Interface
14 DB7 H/L Data Bit 7 4 or 8-Bit Interface
15 A -- Backlight Power Supply for Backlight
16 K -- Backlight Power Supply for Backlight

• BLOCK DIAGRAM

Micro Electronics Corp Http://[Link]

• DIAGRAM CCM2040
• ENVIRONMENTAL CONDITIONS

Item Operating Non-Operating Remarks

Min Max Min Max
Ambient 0°C 50°C -20°C 70°C Normal
Temperature Temperature Type
(Ta) -20°C 70°C -30°C 80°C Extended
Temperature Type
2
Vibration -- 0.5G -- 2G G=9.8 m/s
Shock -- 3G -- 50G XYZ Directions
Corrosion Gas No Corrosion Gas

• OPTICAL CHARACTERISTICS

TN TYPE
Item Symbol Condition Min Typ Max Unit
Viewing Angle ∅2-∅1 K=1.4 20 -- -- Deg
Contrast Ratio K ∅=25° -- 3 -- --
θ=0°
Response Time (Rise) tr ∅=25° -- 200 250 ms
θ=0°
Response Time (Fall) tf ∅=25 -- 200 300 ms
θ=0°

STN TYPE
Item Symbol Condition Min Typ Max Unit
Viewing Angle ∅2-∅1 K=1.4 40 -- -- Deg
Contrast Ratio K ∅=25° 3 -- -- --
θ=0°
Response Time (Rise) tr ∅=25° -- 200 300 ms
θ=0°
Response Time (Fall) tf ∅=25 -- 250 350 ms
θ=0°

Micro Electronics Corp Http://[Link]

• BACKLIGHT CHARASTERISTICS

EL BACKLIGHT
Electrical Data
Parameter Description
Power Supply Up to max. 230 RMS
Wave Shape Sinusoidal
Frequency Up to max. 3 KHz
Efficiency η (dvA/cd)
Capacity 0.50 nF/cm2
Operating Current 160mA

Optical Data
Parameter Description
Power Supply 110v 400Hz sinusoidal
Luminous Intensity 69.3 cd/m2 resp 20.4fl
Emission Color Green/Blue 500nm
x=0.173, y=0.407
Homogenity ± 5%
Useful Life Unlimited
Brightness Uniformity 1000h approx. 80%
(Relative Humidity <80%) 5000h approx. 50%

Micro Electronics Corp Http://[Link]

LED BACKLIGHT
Characterisitcs
Low Voltage Driving (DC) is available without invertor
No noise occurrence
Life : 20K Hours
Item Symbol Conditions Rating Unit
Power Dissipation Pmax -- 1960 mW
Forward Voltage Vf Type 4.4 V
Reverse Voltage Vr min Ir=1400uA 10 V
Average Forward Current If max Vf=4.4V 350 mA

• AC CHARACTERISTICS
(Vdd=5V ± 10%, Vss=0V, Ta=25°C)
Write Mode (Writing data from Micom to KS070B)
Item Symbol Min Max Unit
Enable Cycle Time TCYCE 500 -- ns
Enable Pulse Width High Level PW EH 220 -- ns
Enable Rise/Fall Time tEr, tEf -- 25 ns
Address Set-up Time RS, R/W to E tAS 40 -- ns
Address Hold Time tAH 10 -- ns
Data Set-up Time tDSW 60 -- ns
Data Hold Time (Writing) tH 10 -- ns
Data Hold Time (Reading) tDHR 10 -- ns

• TIMING CHARACTERISTICS

Micro Electronics Corp Http://[Link]

• CONTROL AND DISPLAY COMMAND
Command RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Remark
Display Clear L L L L L L L L L H
Return Home L L L L L L L L H X Cursor Moves to First Digit
Entry Mode L L L L L L L H I/D SH I/D: Set Cursor Move
Set Direction
H-Increase L-Decrease
SH: Specifies Shift of
Display
H-Display is Shifted
L-Display is Not Shifted
Display L L L L L L H D C B D: Display (H-on, L-off)
On/Off C: Cursor (H-on, L-off)
B: Blinking (H-o, L-off)
Shift L L L L L H S/C R/L X X SC: (H-Display Shift, L-
Cursor Move)
R/L: (H-Right Shift, L-Left
Shift)
Set Function L L L L H DL N F X X DL: (H-8 Bits Interface, L-4
Bits Interface)
N: (H-2 Line Display, L-1
Line Display)
F: (H-5 x 10 Dots, L-5 x7
Dots)
Set CG RAM L L L H CG RAM Address CG RAM Data is Sent and
Address (corresponds to address) Received After this Setting
Set DD RAM L L H DD RAM Data is Sent and
Address DD RAM Address Received After this Setting
Read Busy L H BF BF: (H-Busy, L-Ready)
Flag & -- Reads BF: Indicates
Address Address Counter Used for Both DD & CG Internal Operation is Being
RAM Address Performed.
-- Read Address Counter
Contents
Write Data H L Write Data Write Data into DD or CG RAM
Read Data H H Read Data Read Data from DD or CGRAM