Hand Held

Digital Tachometer
Model M740

M740
Inactive Design
Replaced by
Checkline Model DT205L-12
(570) 541-5063

Operating Manual
Avtron Industrial Automation, Inc.
8901 E. Pleasant Valley Road, Independence, Ohio 44131 U.S.A.
Phone: (1) 216-642-1230 Fax: (1) 216-642-6037
Email: tachs@[Link]

03/2007
NOTES Table of Contents
1.0 Introduction........................................................................................................................2

2.0 Overview.............................................................................................................................3

3.0 Contents of Complete Kit................................................................................................4

4.0 Installing/Replacing Batteries..........................................................................................5

5.0 Measuring RPM – Non-Contact Mode..........................................................................6

6.0 Measuring RPM – Contact Mode...................................................................................7

7.0 Measuring Surface Speed and Length............................................................................8

8.0 Built-in Memory System...................................................................................................9

9.0 Range and Accuracy........................................................................................................10

- 12 - -1-
1.0 Introduction

The M740 Hand-Held Digital Tachometer is a combination model designed for

Contact as well as Non-Contact operation. It employs a precise Optical Laser System Model/P/N M740 A27077
that permits measurement of RPM from up to 14 feet away, when operating in the Display Range 6 to 99,999 RPM
Non-Contact mode, and is supplied with a screw-in Contact Adapter for measuring Accuracy ±1 RPM: 6 to 8300 RPM
±2 RPM: 8300 to 25,000 RPM
RPM, surface speed and length in the Contact operating mode. Rotational speed is ±0.006% of reading ±1 digit (±6 RPM max.): 25,000 to 99,999 RPM
displayed in RPM units (revolutions per minute) while the surface speed and length
can be displayed in a variety of user-selected engineering units. Display 5 digit 0.47" (12mm) high LCD
Measuring Units RPM (on contact using adapter, included)
When operating in the Non-Contact mode, a small piece of reflective tape must be For YPM, mPM, FPM, IPM and Length: YRD, m, FT and IN
affixed to the rotating shaft or other rotating element. Refer to Operating Procedure. use 12" wheel with Contact adapter.

Measuring Distance 14' (4.2m) maximum

Memory System 13 readings are stored in memory and retained for 5 minutes
(last, max., min. and 10 extra measurements)
Detection Laser diode/contact

Non-Contact RPM System Control Single chip C-MOS microprocessor

Over Range Indicator Flashing numerals
Update Time 1 second (typical)
Batteries Included Size: 2 AA 1.5V
Life: Approx. 40 hrs.
Contact RPM Low Voltage Indicator Flashing “LO BAT” display
Operating Temperature 32º to 113ºF (0º to 45ºC)

Construction Die-cast aluminum housing

Weight 0.8 lb. (365g)
Surface Speed & Length Dimensions 6.6"L x 2.4"W x 1.8"H (167.5 mm x 60 mm x 46 mm)
Warranty 1 year
Standard Accessories Reflective tape, 2 cone adapters, 1 funnel adapter, calibration
certificate, instruction manual, carrying case, Contact adapter,
master wheel (12" cir.) and 3.5" extension shaft

NOTES

Do not point the laser beam into eyes as

permanent damage could result.

-2- - 11 -
9.0 Range and Accuracy 2.0 Overview

Model M740
R: Revolutions Single Range Accuracy Resolution
Non-Contact RPM 6 - 8,300 ±1 1
(rev./min) 8,300 - 25,000 ±2 Screw-In contact Adaptor
25,000 - 99,999 ±0.006% of reading, ±1 digit
(or ±6 RPM max.)
Contact RPM (rev./min.) 0.8 - 9,999.9 ±0.6% 0.1 Measure Button
10,000 - 25,000 ±0.006% of reading, ±1 digit 1 LCD Display on M740
(or ±2 RPM max.)

F: Feet Single Range Accuracy Resolution

F/M (feet/min.) 0.8 - 9,999.9 ±0.6% 0.1
10,000 - 25,000 ±1
FT (length:feet) 0.2 - 9,999.8 0.2
10,000 - 99,999 1

Y: Yard Single Range Accuracy Resolution

Y/M (yards/min.) 0.25 - 999.99 ±0.06 0.01
10,000 - 8,333.3 ±0.3 0.1
YD (length:yards) 0.05 - 999.95 0.05
1,000 - 9,999.9 0.1
10000 - 99,999 1

I: Inches Single Range Accuracy Resolution

I/M (inches/min.) 9 - 99,999 ±0.006% of reading, ±1 digit 1
(or ±6 RPM max.)
IN (length) 2 - 99,998 2

M: Meters Single Range Accuracy Resolution

m/M (meters/min.) 0.23 - 999.9 ±0.06 0.01
1,000.0 - 7,620.0 ±0.3 0.1
m (length:meters) 0.05 - 999.95 0.05
1,000.0 - 9,999.9 0.1
10,000 - 99,999 1
Note: When using the 12" master wheel, accuracy can be affected as much as 0.3% of reading

Although the tachometer alone is able to achieve the above ranges, Operating Mode Selector
the master wheel has a maximum speed limitation of 3,000 FPM
(for safety reasons).
Memory Switch
Use caution when working near moving machinery. Battery Compartment

- 10 - -3-
3.0 Contents of Complete Kit 8.0 Built-In Memory System

The M740 includes an automatic built-in memory system, capable of storing the
Last, Maximum, and Minimum readings for recall to the display. These values
are stored automatically and there is no need to press any buttons to store data.
G
Note:
D • When utilizing the Length Measurement functions, only
the Last reading is retained in the display.
• The stored data will be deleted when the Tachometer
B automatically powers off.

Recall Stored Readings

To recall stored readings to the display, press the Memory Switch. A stored value
will alternately flash on the display with the memory location number (1, 2 …10).

C
F Clearing Stored Readings
To erase all stored readings, press and hold the Memory Switch for five (5) or more
A seconds until the display shows “CCCCC.” This indicates that the memory
was successfully erased.

A. Tachometer
B. 12" Surface Speed Wheel
C. Batteries (2 pcs. x AA)
D. 2 Cone Tip Adapters
E. Screw-In Contact Adapter
F. Reflective Tape
G. Carrying Case
Not shown
Instruction manual stored behind foam
Certificate of Calibration
Funnel Adapter
Shaft Extension
-4- -9-
7.0 Measuring Surface Speed & Length 4.0 Installing/Replacing Batteries

1. Select the 12-inch Surface Speed Wheel and 1. Loosen the two black screws at the bottom
carefully place it on the shaft of the Screw-in edge of the Tachometer using a slotted screw
Contact Adapter, making sure to align the pin driver or coin.
on the shaft with the slot on the wheel.
Warnings: The Shaft Extension Accessory should
not be used with the Surface Speed Wheel.

2. Rotate the Operating Mode Selector Switch to

the desired unit of measure for surface speed 2. Remove the battery compartment cover plate exposing the battery sleeve.
or length.
Select desired unit of
measure for Surface 3. Insert the AA batteries, observing the proper
Speed or Length. battery polarity indicated on a label inside the
battery compartment.

3. Position the wheel carefully on the moving

surface. Apply enough pressure to eliminate
any slip.

4. Press and hold the white Measure Button located Note: The M740 is designed to automatically power off after five (5) minutes of
on the right side of the Tachometer. “non-use” to conserve battery power.

5. The display will update approximately one time per second and show
the measured surface speed or length in the units selected by the
Operating Mode Selector Switch.

6. Release the Measure Button prior to removing the Tachometer from the
rotating shaft or moving surface. The last reading will be retained on
the display.
Readings will be retained in memory for 5 minutes. This time can be
extended indefinitely by re-pressing the Memory Switch within each
5-minute period.

-8- -5-
5.0 Measuring RPM – Non-Contact 6.0 Measuring RPM – Contact Mode
Mode
1. Place a small piece of reflective tape (included) on the rotating shaft, 1. Screw in the Contact Adapter onto the front
disc, pulley, etc. of the unit.
Notes on Measurements: 2. Rotate the Operating Mode Selector Switch to
• If the rotating element is highly reflective, it may be necessary the desired unit of measure for surface speed
to paint it a darker color in order to ensure reliable results. or length.
• If the sensing distance to the object is less than 5" (127 mm), Notes: The shaft extension accessory can
reflective tabs, optionally available, should be used instead of be used to help reach the end of the
the reflective tape included with the instrument. shaft; however, under no circumstances Cone Rubber Rip
should this extension be used with the
Surface Speed Wheel.
2. Aim the Tachometer at the target (Reflective
3. Rotate the Operating Mode Selector Switch to
Tape), keeping the Tachometer at least 5"
Contact RPM.
(127 mm) but not more than 14'(4.3 meters)
away from the reflective target. 4. Position the tip carefully on the end rotating
Shaft Pin
shaft, insuring that it is positioned in the
center of the shaft. When using the 12"
wheel: Position the wheel carefully on the
moving surface. Apply enough pressure to
eliminate slip.
3. Press and hold the Measure Button for several seconds to observe the 5. Press and hold the white Measure Button
display as it changes in accordance with the speed of the shaft or located on the right side of the Tachometer.
rotating element. As soon as the laser beam hits the target, the
Tachometer will begin displaying speed measurements. 6. The display will update approximately one
time per second and show the measured
If the laser beam is properly aligned with the target, the RPM indicator rotational speed in RPM. Use FPM when using
will be flashing. the 12-inch wheel.
4. Release the Measure Button prior to removing the Tachometer from the 7. Release the Measure Button prior to removing
rotating shaft. The last reading will be retained on the display. the Tachometer from the rotating shaft. The
Readings will be retained in memory for 5 minutes. This time can be last reading will be retained on the display.
extended indefinitely by re-pressing the Memory Switch within each Readings will be retained in memory for 5 minutes.
5-minute period. This time can be extended indefinitely by re-pressing
the Memory Switch within each 5-minute period.

-6- -7-