19 18 17 16 15 14 13 12 11 10

GENERAL NOTES ABBREVIATIONS NOTES

G1. ALL DIMENSIONS ARE IN MILLIMETRES UNO. APPROX. - APPROXIMATE RHS - RECTANGULAR HOLLOW SECTION
G2. ALL ANGLES ARE IN DEGREES UNO.
A.P.I. - AMERICAN PETROLEUM INSTITUTE RSA - ROLLED STEEL ANGLE
G3. ALL DIMENSIONS AND ANGLES ARE TRUE IN THE PLANE IN WHICH THE VIEW LIES UNO.
G4. IT IS THE RESPONSIBILITY OF THE FABRICATOR TO VERIFY ALL DIMENSIONS AND ANGLES, OTHER THAN MAIN LAYOUT DIMENSIONS, PRIOR TO FABRICATION. ARRGT. - ARRANGEMENT PFC - PARALLEL FLANGE CHANNEL
G5. FABRICATOR TO HIGHLIGHT ANY INCONSISTENCY IN SPECIFICATION AND / OR DRAWINGS AND RAISE A TECHNICAL QUERY TO OBTAIN CLARIFICATION. ASTM - AMERICAN SOCIETY FOR TESTING MATERIALS SCH. - SCHEDULE
G6. ALL DEPTHS IN METERS AND RELATIVE TO M.S.L. UNO ALL ELEVATIONS RELATIVE TO MUDLINE. A.W.S. - AMERICAN WELDING SOCIETY SECT. - SECTION
F G7. DIMENSIONS NOT TO BE SCALED FROM DRAWINGS. B.S. - BRITISH STANDARD SHT. - SHEET F
G8. LOW FRICTION MATERIAL TO BE MECHANICALLY FIXED IN PLACE AND SHARP EDGES REMOVED AS SPECIFIED ON DRAWINGS. B.O.P. - BOTTOM OF PIPE SIM. - SIMILAR
G9. GENERAL REQUIREMENTS FOR TRACEABILITY OF MATERIALS IN ACCORDANCE WITH W1 AND W8.
CAT - CATEGORY SIV. - SUBSEA INTERVENTION VALVE
G10. GENERAL REQUIREMENTS FOR STRUCTURAL MATERIALS IN ACCORDANCE WITH W1.
CEV - CARBON EQUIVALENT VALUE S.O.P. - SETTING OUT POINT
G11. GENERAL REQUIREMENTS FOR STRUCTURAL FABRICATIONS IN ACCORDANCE WITH REF. W1 AND W4 BASED ON AWS D1.1.
G12. GENERAL REQUIREMENTS FOR PIPING FABRICATIONS SHALL BE AS FOLLOWS: CHS - CIRCULAR HOLLOW SECTION SPEC. - SPECIFICATION
· EXPORT SPOOLS IN ACCORDANCE WITH DNVGL-ST-F101 AND W6. COL. - COLUMN SQ. - SQUARE
· FLET LARGE BORE PIPING AND INFIELD SPOOLS (>2" NPS) IN ACCORDANCE WITH DNVGL-ST-F101 AND REF. W3. CONN. - CONNECTION S.S. - STAINLESS
· FLET SMALL BORE PIPING (2" NPS) IN ACCORDANCE WITH ASME B31.8 AND REF. W3. CONT. - CONTINUED / CONTINUOUS STD. - STANDARD
CL - CENTRELINE STIFF. - STIFFENER
CTR. - CENTRE STRUCT. - STRUCTURAL
C/C - CENTRE TO CENTRE STWK. - STEELWORK
C/W. - COMPLETE WITH S.W.L. - SAFE WORKING LOAD
COATING, CORROSION & SURFACES
DET. - DETAIL SYM. - SYMMETRICAL
C1. STRUCTURAL STEEL PROTECTION & PAINTING TO BE IN ACCORDANCE WITH SPECIFICATION NORSOK M-501 7B. DIA. OR ∅ - DIAMETER SMYS. - SPECIFIED MINIMUM YIELD STRENGTH
C2. ALL COLOURS AND MARKINGS TO BE IN ACCORDANCE WITH NORSOK M-501 SYSTEM 7.
E DIAG. - DIAGONAL T&B - TOP AND BOTTOM E
C3. ANY DAMAGE TO PAINTED OR COATED SURFACES TO BE REINSTATED IN ACCORDANCE WITH SPECIFICATION IN NORSOK M-501 SYSTEM 7.
DIM. - DIMENSION THK or t - THICK
C4. EXTERNAL MUDMAT SKIRTS, MUDMAT STIFFENERS SHALL BE PAINTED WITHIN 50 mm OF BOTTOM EDGE OF BOTTOM PLATE. UNDERSIDE/INSIDE OF MUDMAT
SHALL NOT BE PAINTED UNO. DPI - DYE PENETRANT INSPECTION T.O.P.
L - TOP OF PLATING
C5. CONTACT SURFACES BENEATH WASHERS/NUTS SHALL BE MASKED PRIOR TO PAINTING TO GUARANTEE ELECTRICAL CONTINUITY FOR BOLTED CONNECTIONS. ALL DRG. - DRAWING T.O.S. - TOP OF STEEL
MASKINGS REMOVED PRIOR TO INSTALLING OF FASTENERS. E - EASTING TYP. - TYPICAL
C6. COLOUR SCHEDULE AS FOLLOWS: EEMUA - ENGINEERING EQUIPMENT & MATERIALS UNO - UNLESS NOTED OTHERWISE
USERS ASSOCIATION VERT. - VERTICAL
COLOUR SCHEDULE (UNO) EL. - ELEVATION W.P. - WORKPOINT
EN - EUROPEAN STANDARD W.T. - WALL THICKNESS
ITEM/AREA COLOUR RAL CODE EQUIP. - EQUIPMENT - INDICATES THROUGH MEMBER
EQUIV. - EQUIVALENT - INDICATES PRINCIPAL DIRECTION OF ROLLING OF STEEL
STRUCTURAL MEMBERS AND PLATE YELLOW 1004 GOLDEN YELLOW
E.R.S. - EXTERNAL RING STIFFENERS
PIPING YELLOW 1004 GOLDEN YELLOW E.W. - EACH WAY
F.F. - FAR FACE
PADEYES & ROV INTERVENTION POINTS ORANGE 2004 PURE ORANGE F.S. - FAR SIDE
D G.A. - GENERAL ARRANGEMENT D
LETTERING BLACK 9017 TRAFFIC BLACK
GALV. - GALVANISED
LETTERING WHITE 9002 GREY WHITE GR. - GRADE
HEA, HEB - EUROPEAN WIDE FLANGE BEAMS
C7. FLET PIPING ANTI-CORROSION PAINT (EXCEPT PRE COATED CPI) TO BE IN ACCORDANCE WITH BAS-101 0665. HRC - ROCKWELL HARDNESS
C8. WELL JUMPERS FJC TO HAVE COATING IN ACCORDANCE WITH TFMC ANTI CORROSION; W13 AND INSULATION COATING; W14. HORIZ. - HORIZONTAL
C9. SPOOLS FJC TO FOLLOW INSULATION REQUIREMENTS DRAWING IN ACCORDANCE WITH : I.D. - INSIDE DIAMETER
· IMPP FJC ON MAIN PIPING IN ACCORDANCE WITH W15 & W16.
IDC - INTER DISCIPLINE CHECK
· SILICONE FJC WITH CONNECTOR ACCORDANCE WITH W12.

GROUP - C:\Work\#Vault\#CAD\Projects\AUP\Santos\AA0043\#DR\AA0043-DR-AA-10002 - 30-Jun-22 - 12:06 PM - Ahmad Syah Hasbullah

C10. GAS EXPORT SPOOL FJC TO BE COATED IN ACCORDANCE WITH CLIENT DATASHEET W5 OR W17. INT. - INTERNAL
IPE - EUROPEAN NARROW FLANGE BEAMS
ITA - INLINE TEE ASSEMBLY
BOLTS & FASTENERS ASSEMBLY LAT - LOWEST ASTRONOMICAL TIDE
BF1. ALL STRUCTURAL BOLTS/STUDS AND FASTENERS C/W NUTS AND WASHERS UNO. LG. - LONG
BF2. ALL PRESSURE RETAINING BOLTS/STUDS AND FASTENERS C/W NUTS AND WASHERS UNO L.H. - LEFT HAND
C BF3. FASTENERS TO BE SNUG TIGHT CONDITION UNO (RCSC SPECIFICATION). Izuddin
Muhamm
Digitally signed by
Izuddin Muhammad
PP CVL

C
Date: 2022.07.05 [Link]

LOC'N - LOCATION
+08'00'
ad

BF4. FASTENERS TO HAVE ANTI-SEIZE/GREASE (MOLYKOTE 1000 OR SIMILAR) OR COEFFICIENT OF FRICTION (i.e. 0.13) APPLIED UNO. 1 [Link].22 IFC ASH ALH IMU MT
m - METRES
BF5. HINGE ASSEMBLIES AND TRUNNION CONNECTIONS ARE TO HAVE GREASE/LUBE (MOLYKOTE 1000 OR SIMILAR) OR COEFFICIENT OF FRICTION (i.e. 0.13) A.2 [Link].22 RE-IDC MHI DJS IMU MT
APPLIED AND RUNNING FREE. mm - MILLIMETRES
A.1 [Link].22 RE-IDC MHI DJS IMU MT
BF6. ALL SUBSEA FASTENERS/BOLTS TO BE PLAIN FINISH(UNCOATED) UNO. ALL FASTENERS PLAIN (BLACK FINISH), UNLESS STATED ON DRAWING TO BE XYLAN COATED. MAT'L - MATERIAL
NO FASTENERS TO BE GALVANISED. A [Link].21 IDC ALH DJS IMU MT
MAX. - MAXIMUM
BF7. FASTENERS TO SCHEDULE AS FOLLOWS(W1). DRN D.O. ORG ENG
MIN. - MINIMUM REV DATE DESCRIPTION
BY CHK ENG APP
MK. - MARK
FASTENER SCHEDULE MKD. - MARKED REVISION HISTORY
MPa - MEGA PASCALS
NUT M.P.I. - MAGNETIC PARTICLE INSPECTION
BOLT DESCRIPTION
(WASHER)
M.T.O. - MATERIAL TAKE OFF
MISC. - MISCELLANEOUS
ASTM A194 GRADE 7M +S3/S4/S5 FOR SUBSEA PRESSURE CONTAINING
ASTM A320 L7M MUT - MANUAL ULTRASONIC TESTING
(ASME PCC-1 US CUSTOMARY) (SOUR SERVICE)
N - NORTHING
NDE - NON DESTRUCTIVE EXAMINATION
B ASTM A320 L7
ASTM A194 GRADE 7 +S3/S4/S5 FOR SUBSEA PRESSURE CONTAINING CLIENT B
(ASME PCC-1 US CUSTOMARY) (NON-SOUR SERVICE) NDT - NON DESTRUCTIVE TESTING
SANTOS
N.F. - NEAR FACE
PROJECT
ASTM A194 GRADE 2H N.S. - NEAR SIDE
ASTM A193 B7
(ISO 7089 300 HV)
FOR STRUCTURAL APPLICATIONS
NOM. - NOMINAL
BAROSSA PROJECT SURF T&I
NTS - NOT TO SCALE
OPP. - OPPOSITE
BF8. ALL STRUCTURAL AND PRESSURE RETAINING FASTENERS TO BE SUPPLIED WITH EN 10204:2004 TYPE 3.1 CERTIFICATE, EXTENDING TO COATINGS. O.D. - OUTSIDE DIAMETER
BF9. CARBON AND LOW ALLOY STEEL BOLTING MATERIALS SHALL BE CVN TESTED:
O/A - OVERALL Subsea 7 owns the copyright of this document which is supplied in confidence and
· TESTING TEMPERATURE -35°C OR LESS.
· CVN IMPACT RESULTS TO MEET OR EXCEED AVERAGE > 50 J AND MIN > 40 J. O/O - OUT OF must not be used for any purpose other than that for which it is supplied and
must not be reproduced without express permission in writing from the owners.
BF10. ALL PRESSURE RETAINING STUDS OR HEAVY HEX BOLTS TO BE FULLY UNC THREADED, AND TO ASME B18.2.1 DIMENSIONS. PCM - PARAMETER FOR CRACK MEASUREMENT
TITLE
BF11. ALL PRESSURE RETAINING NUTS TO BE HEAVY HEX UNC TYPE, AND TO ASME B18.2.2 DIMENSIONS. P.C.D. - PITCH CIRCLE DIAMETER
BF12. ALL STRUCTURAL HEX BOLTS TO BE FULLY THREADED, AND TO ISO 4017 DIMENSIONS. PLT., PL - PLATE
BF13. ALL STRUCTURAL HEX NUTS, AND TO ISO 4032 DIMENSIONS. PLET - PIPELINE END TERMINATION GENERAL NOTES & SPECIFICATIONS
BF14. ALL STRUCTURAL HEXAGON SOCKET COUNTERSUNK FLAT SCREWS TO BE FULLY THREADED, TO ISO 10642 DIMENSIONS. PTFE - POLYTETRAFLUOROETHYLENE
A BF15. RESTRICTIONS FOR SOUR SERVICE APPLY ACCORDING TO ISO 15156 WHEN APPLICABLE. ALL MANDATORY REQUIREMENTS IN ISO 15156-2/3 SHALL APPLY. QTY. - QUANTITY A
BF16. MAXIMUM HARDNESS SHALL NOT EXCEED 35 HRC FOR CARBON AND LOW ALLOY STEELS. P.W.H.T. - POST WELD HEAT TREATMENT SIZE SCALE U.O.S. SHEET

BF17. THE HARDNESS OF BOLTS AND NUTS SHALL BE VERIFIED FOR EACH LOT (I.E. BOLTS OF THE SAME SIZE AND MATERIAL, FROM EACH HEAT OF STEEL AND HEAT RAD. - RADIUS A1 NTS 1 OF 3
TREATMENT BATCH) AND BE TRACEABLE BACK TO HEAT NUMBER. REF. - REFERENCE CLIENT Drg No. REV
BF18. PRESSURE RETAINING BOLTING SHALL BE QUALIFIED, MANUFACTURED AND MARKED IN ACCORDANCE WITH API 20E BSL2. REQ'D - REQUIRED BAS-263 2510
BF19. TO ACHIEVE THE DESIRED TENSILE PRELOAD IN THE STUDS, THE STUD THREADS AND THE BEARING FACE OF THE NUTS SHALL BE WELL LUBRICATED.
REV. - REVISION
- RIGHT HAND
SUBSEA 7 Drg No. 1
R.H. AA0043-DR-AA-10002
19 18 17 16 15 14 13 12 11 10
 29 28 27 26 25 24 23 22 21 20
STRUCTURAL STEEL FABRICATION CATHODIC PROTECTION NOTES
SS1. REMOVE ALL SHARP EDGES & BURRS, MINIMUM RADIUS 2mm. CP1. SACRIFICIAL ANODES SHALL BE AL-ZN-IN MATERIAL IN ACCORDANCE WITH W2 1. THIS DRAWING IS TO BE READ IN CONJUNCTION WITH SHEET 1.
SS2. ALL TUBULARS ARE CALLED UP BY OUTSIDE DIAMETER AND WALL THICKNESS, E.G. 168.3 X 12.7 WT. CP2. ELECTRICAL CONTINUITY OF ALL PERMANENT ITEMS ATTACHED TO THE STRUCTURES (INCLUDING BOLTING, HINGE PINS, YOKE) SHALL BE MEASURED BY
SS3. STRUCTURAL FABRICATION/WELDING IN ACCORDANCE WITH AWS D1.1, W1, W4 AND API RP 2A-LRFD. RECORDING THE ELECTRICAL RESISTANCE BETWEEN EACH INDIVIDUAL ITEM AND THE STRUCTURE. NO ITEM SHALL HAVE A RESISTANCE GREATER THAN 0.1 OHM.
SS4. WELD FILLER MATERIAL TO BE SELECTED FROM TABLE 3.1 OF AWS D1.1 BASED ON MINIMUM BASE MATERIAL GRADE. ULTIMATE TENSILE CAPACITY AND YIELD ALL RESULTS SHALL BE INCLUDED IN THE FINAL AS-BUILT DOCUMENTATION REQUIREMENTS. NO REQUIREMENT FOR CONTINUITY OF TEMPORARY ITEMS
STRENGTH TO OVER-MATCH BASE MATERIAL. CP3. WHERE CONTINUITY STRAPS ARE USED, LUG SHALL BE CRIMPED AND SOLDERED / BRAZED TO CABLE.
SS5. EXCEPT WHERE NOTED ON FABRICATION DRAWING, STRUCTURAL FABRICATION TOLERANCES TO BE IN ACCORDANCE WITH W4. CP4. CONTINUITY STRAPS SHALL BE INSTALLED AS INDICATED ON DRAWING ON THE FOLLOWING BASIS.
F TOLERANCES SHALL BROADLY BE IN ACCORDANCE WITH AWS D1.1. · IN ACCORDANCE WITH W1 F
SS6. ALL WELDING SYMBOLS ARE IN ACCORDANCE WITH AWS A2.4. · H07V-K PVC INSULATED, 70 mm² COPPER CABLES, MULTI-STRAND AND FLEXIBLE TYPE, TO BE USED SUBJECT TO REVIEW AND APPROVAL
SS7. TRANSITIONS IN STRUCTURAL PLATE TO BE TAPERED 1:4 UNO. · TWO STRAPS WITH INDEPENDENT ATTACHMENT POINTS TO ALLOW FOR REDUNDANCY
SS8. RAT HOLES (ACCESS HOLES, COPE HOLES) IN ACCORDANCE WITH AWS D1.1, WITH BUYER APPROVAL REQUIRED. SEE RAT HOLE DETAILS ON SHEET 3. · CABLES TO BE OF SUFFICIENT LENGTH TO FACILITATE INSTALLATION AND OVERAGE TO BE SECURED TO STRUCTURE TO MINIMIZE SNAG RISK
SS9. ALL FILLET WELDS SHALL BE MINIMUM 6 mm CONTINUOUS UNO. CP5. PIN-BRAZED CONNECTED COPPER CABLES ON PIPING TO USE SUITABLE LUG.
SS10. ALL INTERNAL BOXED/SEALED AREAS AND INTERNAL WELDS SHALL BE INSPECTED AND SUBJECT TO NDT PRIOR TO WELDING COVER PLATES. INTERNAL SURFACES CP6. MECHANICALLY CONNECTED CABLES ON STRUCTURAL FRAMES HAVE DETAILS SHOWN BELOW.
MAY REMAIN UNCOATED UNO.
SS11. ALL STRUCTURAL WELDING SHALL BE PERFORMED TO PROCEDURES THAT HAVE BEEN QUALIFIED BY AN APPROVED PROCEDURE QUALIFICATION RECORD. COPPER LUG c/w BRAZED M12 ASTM A193 B7
SS12. WELDING SHALL BE A LOW HYDROGEN PROCESS. CABLE END HEX HD x 20 LG c/w 2
SS13. ALL FILLET WELDS SHALL BE CONTINUOUS AROUND EDGES OF PLATE & THROUGH RAT/COPE HOLES UNO. No. SERRATED WASHER
SS14. WHERE ACCESS IS FOUND UNACCEPTABLY RESTRICTIVE BETWEEN STIFFENERS OR WHERE CLOSURES ARE FORMED THEN FILLET WELDS MAY BE SUBSTITUTED BY
SINGLE SIDED FULL PENETRATION GROOVE WELDS.
SS15. AS A MINIMUM ALL BOXES, TUBULARS AND CLOSED SECTIONS TO HAVE 2 NO. 35 DIA. HOLES AT THEIR UPPER AND LOWER MOST POSITION (AT 50 mm MINIMUM
FROM EACH END OR ADJOINING MEMBER). SEE NOTE SS16 AND SS17 ALSO.
SS16. FREE FLOODED AND SEALED MEMBERS (WHERE SPECIFIED) TO BE FITTED WITH FLOOD GROMMETS, REFER TO FLOOD GROMMET DETAIL IN THIS SHEET. SINGLE CORE 70mm² PVC COPPER STRUCTURE
GROMMETS TO BE CEMENTED IN PLACE WITH BIOHESIVE 225 SILICONE ADHESIVE. CABLE CRIMPED AND BRAZED INTO (NO PAINT LOCAL TO
SS17. FREE FLOODED HOLLOW MEMBERS TO HAVE ROEMEX RX-5720 CORROSION/BIOCIDE STICKS ADDED TO ACHIEVE 500 PPM CONCENTRATION AFTER FLOODING. SUITABLE LUG TYPE CABLE END AS WASHER/CABLE)
E SS18. ANY UNDEFINED WELDS TO BE CLARIFIED WITH BUYER AND COMPANY. SHOWN OR SUITABLE EQUIVALENT. E
LENGTH TO BE DETERMINED ON SITE.

TYPICAL CONTINUITY CONNECTION DETAIL

PIPING & SPOOL FABRICATION SCALE: NTS

PF1. FLET PIPING FABRICATION/WELDING IN ACCORDANCE WITH ASME B31.8 OR DNVGL-ST-F101 AND CLIENT STANDARD W3. CP7. WHERE THE STRUCTURE HAS A SLIDING INTERFACE WITH THE MUDMAT, THE RESISTANCE BETWEEN THE STRUCTURE & MUDMAT MUST BE MEASURED.
PF2. FLET PIPING FABRICATION TOLERANCE TO MEET PFI ES-3 UNLESS STATED OTHERWISE ON FABRICATION/ASSEMBLY DRAWINGS. CP8. NO ITEM SHALL HAVE A RESISTANCE GREATER THAN 0.1 OHM AT A MINIMUM TEST CURRENT OF 10 AMPS. ALL RESULTS SHALL BE INCLUDED IN THE FINAL AS-BUILT
PF3. PRODUCTION AND SERVICE SPOOL IN ACCORDANCE WITH DNVGL-ST-F101 AND CLIENT STANDARD W3. DOCUMENTATION REQUIREMENTS.
PF4. EXPORT SPOOL IN ACCORDANCE WITH DNVGL-ST-F101 CLIENT STANDARD W6.
PF5. PRODUCTION WELL JUMPERS IN ACCORDANCE WITH ASME B31.8 AND CLIENT STANDARD W11.
PF6. FLET LARGE BORE PIPING AND INFIELD SPOOLS (>2" NPS) IN ACCORDANCE WITH DNVGL-ST-F101 AND REF. W3.
PF7. FLET SMALL BORE PIPING (2" NPS) IN ACCORDANCE WITH ASME B31.8 AND REF. W3.

D D
INSPECTION & NDT FABRICATION MATERIALS
N1. INSPECTION OF STRUCTURAL WELDS SHALL COMPLY WITH AWS D.1.1. NDT EXTENT IN ACCORDANCE WITH W4. NDT FOR PIPING AND SPOOLS AS PER N3. M1. ALL STRUCTURAL STEEL SHALL MEET CLIENT STANDARD, W1 AS AMENDED BY TQD NO. BAS-SS7-STO-TQD-00061 UNLESS PRE-APPROVED BY BUYER AND CLIENT.
N2. REQUIREMENTS FOR EXTENT & TYPE OF INSPECTION & NDT FOR VARIOUS CATEGORIES OF STRUCTURAL WELDS ARE SUMMARISED THE FOLLOWING TABLE: M2. EN 10204:2004 TYPE 3.2 MATERIAL CERTIFICATE FOR ALL PRIMARY AND SECONDARY STEEL. TERIERY STEEL TO HAVE MINIMUM TYPE 3.1 MATERIAL CERTIFICATE,
UNLESS PRE-APPROVED BY BUYER AND CLIENT
M3. ALL PADEYE PLATE SHALL HAVE Z35 THROUGH THICKNESS PROPERTIES.
STEEL CLASSIFICATION TYPE OF CONNECTION VISUAL EXAMINATION UT MT M4. ANY SUBSTITUTION OF MATERIAL SHALL BE SUBJECT TO APPROVAL FROM BUYER.
M5. 4130/4140 STEEL TO MEET ASTM A193 GRADE B7, SMYS 515 MPa (75 ksi) MINIMUM, SMTS 690 MPa (100 ksi), HRC ≤ 35. MATERIAL TO BE PRE-CERTIFIED WITH
PRIMARY
FULL PENETRATION WELDS 100% CVN ≥ 50 J AT -20°C.
(ACCEPTANCE TO
100% 100% M6. ALL 4130/4140 PINS TO BE LOW STRESS STAMPED WITH SMYS = 515 MPa, UNO

GROUP - C:\Work\#Vault\#CAD\Projects\AUP\Santos\AA0043\#DR\AA0043-DR-AA-10002 - 30-Jun-22 - 12:06 PM - Ahmad Syah Hasbullah

AWS D1.1 CYCLICALLY FILLET WELD / PARTIAL
- M7. 4130/4140 GRADE STEEL IS NOT TO BE WELDED
LOADED STRUCTURE) PENETRATION WELD
M8. FOR STRUCTURAL STEEL MATERIALS REQUIRING THROUGH-THICKNESS PROPERTIES AND WITH THICKNESS EQUAL TO OR GREATER THAN 25MM (CV2Z), SHALL BE
SECONDARY Z35 GRADE, UNLESS OTHERWISE APPROVED BY BUYER.
FULL PENETRATION WELDS 20%
(ACCEPTANCE TO M9. MATERIAL IN TABLE BELOW TO MEET OR EXCEED API RP 2A-LRFD, TABLE C.2, C.3 AND C.4.
100% 20%
AWS D1.1 STATICALLY FILLET WELD / PARTIAL M10. ANY UNDEFINED MATERIAL TOUGHNESS CLASS TO BE CLARIFIED WITH BUYER AND COMPANY.
-
LOADED STRUCTURE) PENETRATION WELD
Digitally signed
Izuddin by Izuddin
Muhammad

TERTIARY
Muhammad

C
Date: 2022.07.05
PP CVL

C
[Link] +08'00'

FULL PENETRATION WELDS 20%

(ACCEPTANCE TO 1 [Link].22 IFC MHI ALH IMU MT
100% 20%
AWS D1.1 STATICALLY FILLET WELD / PARTIAL A.2 [Link].22 RE-IDC MHI DJS IMU MT
LOADED STRUCTURE) - EN EQUIVALENT
PENETRATION WELD TOUGHNESS API A.1 [Link].22 RE-IDC MHI DJS IMU MT
MATERIAL STEEL GROUP
CLASS FORM / TYPE A [Link].21 IDC ALH DJS IMU MT
GRADE API 2A LRFD
API 2A LRFD
STANDARD GRADE SMYS(2) STANDARD GRADE SMYS(2) REV DATE DESCRIPTION
DRN D.O. ORG ENG
N3. INSPECTION OF PIPING AND SPOOL WELDS SHALL COMPLY WITH ASME B31.8 OR DNVGL-ST-F101 AS REQUIRED. NDT EXTENT IN ACCORDANCE WITH RELEVANT BY CHK ENG APP
CODE & REF. W3 & W6.
N4. ALL BACK GOUGING (AFTER GRINDING TO REMOVE DAMAGED/HEAT AFFECTED MATERIALS) OF FULL PENETRATION GROOVE WELDS TO HAVE MAGNETIC PARTICLE CV2Z EH36 + Z35 S355 K2 / N +Z35 REVISION HISTORY
INSPECTION PRIOR TO COMPLETION OF WELD ON SECOND SIDE.
ASTM A131 355
CV2 EH36 S355 K2 / N
350 II 355
PLATE EN 10025
CV1 AH36 S355 J2

LIFTING EQUIPMENT NT ASTM A572 Gr. 50 345 S355 J0

B L1. ALL LIFTING EQUIPMENT TO BE CLEARLY MARKED WITH SWL OR WLL. CLIENT B
250 I NT ASTM A131 A 235 S275 JR 275
L2. REQUIREMENTS FOR LIFTING EQUIPMENT SHALL BE IN ACCORDANCE WITH W7, W8, W9, W10. SANTOS
L3. LIFT RIGGING TOLERANCES, MANUFACTURE AND CERTIFICATION SHALL BE IN ACCORDANCE WITH DNVGL-ST-N001.
L4. TESTING AND NDT OF LIFT POINTS ON LIFTED ITEMS AND LIFTING APPLIANCES IS DETAILED IN DNVGL-ST-0378 TABLE 14-2. CV2 A S355 K2 / N PROJECT

L5. PADEYES TO HAVE NDT PERFORMED BEFORE AND AFTER LOAD TESTING. API 2MT2 BAROSSA PROJECT SURF T&I
350 II CV1 B 345 S355 J2 355
ROLLED SECTIONS EN 10025
APPLICABLE COMPANY STANDARD NT ASTM A572 Gr. 50 S355 J0
W1. BAS-101 0586 BAROSSA PROJECT, SUBSEA STRUCTURES FABRICATIONS SPECIFICATION.
250 I NT ASTM A36 36 250 S275 JR 275 Subsea 7 owns the copyright of this document which is supplied in confidence and
W2. BAS-101 0124 BAROSSA PROJECT, STRUCTURAL ANODES DATASHEET.
must not be used for any purpose other than that for which it is supplied and
W3. BAS-101 0585 BAROSSA PROJECT, SPOOL FABRICATION SPECIFICATION . must not be reproduced without express permission in writing from the owners.
W4. BAS-101 0524 BAROSSA PROJECT, STRUCTURAL STEEL WELDING AND NDT DATASHEET . CV2 X52 PSL2 (1) S355 K2H / NH TITLE
W5. BAS-101 0547 BAROSSA PROJECT, HIGH BUILD EPOXY COATING.
W6. BAS-101 0550 BAROSSA PROJECT, EXPORT PIPELINE SPOOL WELDING AND NDT DATASHEET.
350 II CV1 360 S355 J2H 355
W7. BAS-101 0213 BAROSSA PROJECT, FLET FUNCTIONAL SPECIFICATION.
W8. BAS-200 0325 BAROSSA PROJECT, EXHIBIT I, QUALITY REQUIREMENTS.
TUBULAR API 5L X52 PSL2 EN 10210 GENERAL NOTES & SPECIFICATIONS
W9. BAS-101 0221 BAROSSA PROJECT, FLOWLINE DISPLACEMENT INITIATOR FUNCTIONAL SPECIFICATION. NT S355 J0H
A W10. BAS-101 0247 BAROSSA PROJECT, RISER TETHER BASE FUNCTIONAL SPECIFICATION. A
W11. BAS-100 0027 BAROSSA SUBSEA EQUIPMENT - MATERIALS, CORROSION & WELDING REQUIREMENTS. 250 I NT B PSL2 245 S275 JRH 275 SIZE SCALE U.O.S. SHEET

W12. BAS-101 0665 BAROSSA PROJECT, FLOWLINE SPOOL AND FLET SILICONE BASED FIELD JOINT COATING DATASHEET. A1 NTS 2 OF 3
W13. BAS-252 0062 BAROSSA PROJECT, AMBIENT CURED COATING - APPLICATION AND INSPECTION - SPECIFICATION.
NOTES: CLIENT Drg No. REV
W14. BAS-252 0027 BAROSSA PROJECT, SUBSEA PRODUCTION SYSTEM - NOVOLASTIC XG THERMAL INSULATION - APPLICATION AND INSPECTION SPECIFICATION.
W15. BAS-101 0532 BAROSSA PROJECT, PRODUCTION FLOWLINE IMPP FIELD JOINT AND BEND COATING DATASHEET. BAS-263 2510
W16. BAS-101 0539 BAROSSA PROJECT, SERVICE FLOWLINE FIELD JOINT AND BEND COATING DATASHEET.
1.
2.
CNV TEST FOR CV2 AT -20°C MAXIMUM TEMPERATURE.
SMYS in MPa.
SUBSEA 7 Drg No. 1
W17. BAS-101 0546 BAROSSA PROJECT, EXPORT PIPELINE FIELD JOINT COATING DATASHEET. AA0043-DR-AA-10002
29 28 27 26 25 24 23 22 21 20
 39 38 37 36 35 34 33 32 31 30
TYPICAL BEAM ASSEMBLY RUBBER FLOOD GROMMET NOTES
1. THIS DRAWING IS TO BE READ IN CONJUNCTION WITH SHEET 1.

P
CU 2 5
TY
F KNIFE CUT BETWEEN F

T
HOLES
T < 25mm ℄

T ≥ 25mm

Xº
A A

> )
(N
30
TS

T
º
T
2 DIA HOLE TYP. 4 PLACES.

DETAILS OF RUBBER FLOOD GROMMET

AWS SCALE: NTS
s AWS s MATERIAL: SILICONE RUBBER
SYMBOL s AWS
s SYMBOL s SYMBOL SHORE A 60 ±5
AWS SEE FABRICATION NOTE SS16
E E
T

SYMBOL s

T
T < 25mm
∅50
T ≥ 25mm T ≥ 25mm

3
T < 25mm

R1

21
TYPICAL BEAM ASSEMBLY DET. 1 TYPICAL BEAM ASSEMBLY DET. 2
∅29
BEAM TO BEAM WITH EQUAL HEIGHTS BEAM TO BEAM WITH DIFFERENT HEIGHTS
"T" ≥ 25mm & Xº > 30º ∅35

D D
SECTION A-A
SCALE: NTS

RAT HOLE
R1. RATHOLES SHALL BE MINIMISED WHEREVER POSSIBLE.
R2. RATHOLE SIZES, UNLESS SPECIFICALLY DETAILED ON THE SHOP DRAWINGS, SHALL MEET TO AWS D1.1.
R3. RATHOLES OR CUTOUTS IN ANY TUBULAR MEMBER ARE STRICTLY PROHIBITED UNLESS SPECIFICALLY DETAILED ON DESIGN DRAWINGS.

GROUP - C:\Work\#Vault\#CAD\Projects\AUP\Santos\AA0043\#DR\AA0043-DR-AA-10002 - 30-Jun-22 - 12:06 PM - Ahmad Syah Hasbullah

R4. ALL WELDS TO BE CONTINUOUS THROUGH RATHOLES.
R5. FOR CLOSED SECTIONS CONTAINING BIOCIDE, RATHOLES TO BE BLANKED OFF BY 6MM COVER PLATE.

Izuddin Digitally signed by

PP CVL
C
Muhamm Izuddin Muhammad
Date: 2022.07.05

C
[Link] +08'00'
ad

1 [Link].22 IFC MHI ALH IMU MT

A.2 [Link].22 RE-IDC MHI DJS IMU MT
A.1 [Link].22 RE-IDC MHI DJS IMU MT
A [Link].21 IDC ALH DJS IMU MT
DRN D.O. ORG ENG
REV DATE DESCRIPTION
BY CHK ENG APP

REVISION HISTORY

B CLIENT B
SANTOS
PROJECT
BAROSSA PROJECT SURF T&I

Subsea 7 owns the copyright of this document which is supplied in confidence and
must not be used for any purpose other than that for which it is supplied and
must not be reproduced without express permission in writing from the owners.
TITLE

GENERAL NOTES & SPECIFICATIONS

A A
SIZE SCALE U.O.S. SHEET

A1 NTS 3 OF 3
CLIENT Drg No. REV

BAS-263 2510
SUBSEA 7 Drg No. 1
AA0043-DR-AA-10002
39 38 37 36 35 34 33 32 31 30