12/26/24, 10:26 AM 200-301 Exam - Free Actual Q&As, Page 9 | ExamTopics

Question #1201 Topic 1

What differentiates the Cisco OfficeExtend AP mode from the Cisco FlexConnect AP mode?

A. FlexConnect allows a personal SSID to be configured on the AP, and personal SSIDs are not supported with OfficeExtend.

B. OfficeExtend does not support DTLS tunneling of traffic to the WLC, and FlexConnect tunnels traffic to the WLC with DTLS.

C. FlexConnect must be deployed behind a router that NATs the client traffic, and OfficeExtend uses public IP sources.

D. OfficeExtend mode requires indoor APs with internal antennas, and indoor and outdoor APs use FlexConnect mode. Most Voted

Correct Answer: D

Community vote distribution

D (100%)

Question #1202 Topic 1

Refer to the exhibit. A network engineer is configuring a WLAN to connect with the 172.16.10.0/24 network on VLAN 20. The engineer wants to

limit the number of devices that connect to the WLAN on the USERWL SSID to 125. Which configuration must the engineer perform on the WLC?

A. In the Controller IPv6 configuration, set the Throttle value to 125.

B. In the WLAN configuration, set the Maximum Allowed Clients value to 125. Most Voted

C. In the Management Software activation configuration, set the Clients value to 125.

D. In the Advanced configuration, set the DTIM value to 125.

Correct Answer: B

Community vote distribution

B (100%)

https://www.examtopics.com/exams/cisco/200-301/view/9/ 1/28
12/26/24, 10:26 AM 200-301 Exam - Free Actual Q&As, Page 9 | ExamTopics

Question #1203 Topic 1

Refer to the exhibit. An LACP EtherChannel between two directly connected switches is in the configuration process. Which command must be

configured on switch SW2s Gi0/1-2 interfaces to establish the channel to SW1?

A. channel-group 1 mode on

B. channel-group 1 mode desirable

C. channel-group 1 mode active Most Voted

D. channel-group 1 mode auto

Correct Answer: C

Community vote distribution

C (100%)

https://www.examtopics.com/exams/cisco/200-301/view/9/ 2/28
12/26/24, 10:26 AM 200-301 Exam - Free Actual Q&As, Page 9 | ExamTopics

Question #1204 Topic 1

Refer to the exhibit. An administrator must connect SW_1 and the printer to the network. SW_2 requires DTP to be used for the connection to

SW_1. The printer is configured as an access port with VLAN 5. Which set of commands completes the connectivity?

A. switchport mode dynamic auto

switchport private-vlan association host 5

B. switchport mode trunk

switchport trunk pruning vlan add 5

C. switchport mode dynamic desirable

switchport trunk allowed vlan add 5 Most Voted

D. switchport mode dynamic auto

switchport trunk encapsulation negotiate

Correct Answer: C

Community vote distribution

C (100%)

Question #1205 Topic 1

Refer to the exhibit. Which per-hop QoS behavior is R1 applying to incoming packets?

A. marking

B. shaping

C. queuing Most Voted

D. policing

Correct Answer: C

Community vote distribution

C (71%) A (29%)

https://www.examtopics.com/exams/cisco/200-301/view/9/ 3/28
12/26/24, 10:26 AM 200-301 Exam - Free Actual Q&As, Page 9 | ExamTopics

Question #1206 Topic 1

What is the role of the root port in a switched network?

A. It replaces the designated port when the designated port fails.

B. It replaces the designated port when the root port fails.

C. It is the best path to the root from a nonroot switch. Most Voted

D. It is administratively disabled until a failover occurs.

Correct Answer: C

Community vote distribution

C (100%)

Question #1207 Topic 1

What is the temporary state that switch ports always enter immediately after the boot process when Rapid PVST+ is used?

A. forwarding

B. listening

C. learning

D. discarding Most Voted

Correct Answer: D

Community vote distribution

D (78%) C (22%)

Question #1208 Topic 1

What is used to identify spurious DHCP servers?

A. DHCPACK

B. DHCPREQUEST

C. DHCPOFFER

D. DHCPDISCOVER Most Voted

Correct Answer: D

Community vote distribution

D (80%) C (20%)

https://www.examtopics.com/exams/cisco/200-301/view/9/ 4/28
12/26/24, 10:26 AM 200-301 Exam - Free Actual Q&As, Page 9 | ExamTopics

Question #1209 Topic 1

Refer to the exhibit. A packet sourced from 10.10.10.1 is destined for 172.16.3.254. What is the subnet mask of the destination route?

A. 0.0.0.0

B. 255.255.254.0 Most Voted

C. 255.255.255.0

D. 255.255.255.255

Correct Answer: B

Community vote distribution

B (80%) A (16%) 4%

https://www.examtopics.com/exams/cisco/200-301/view/9/ 5/28
12/26/24, 10:26 AM 200-301 Exam - Free Actual Q&As, Page 9 | ExamTopics

Question #1210 Topic 1

Refer to the exhibit. IPv6 must be implemented on R1 to the ISP. The uplink between R1 and the ISP must be configured with a manual assignment,

and the LAN interface must be self-provisioned. Both connections must use the applicable IPv6 networks. Which two configurations must be

applied to R1? (Choose two.)

A. interface Gi0/0

ipv6 address 2001:db8:0F1B:FCCB:ACCE:FCED:ABCD:FA03:/127

B. interface Gi0/0

ipv6 address 2001:db8:0:AFFF::/64 eui-64 Most Voted

C. interface Gi0/1

ipv6 address 2001:db8:0F1B:FCCB:ACCE:FCED:ABCD:FA02:/127

D. interface Gi0/0

ipv6 address 2001:db8:1:AFFF::/64 eui-64

E. interface Gi0/1

ipv6 address 2001:db8:0F1B:FCCB:ACCE:FCED:ABCD:FA00:/127 Most Voted

Correct Answer: BE

Community vote distribution

BE (76%) BC (24%)

https://www.examtopics.com/exams/cisco/200-301/view/9/ 6/28
12/26/24, 10:26 AM 200-301 Exam - Free Actual Q&As, Page 9 | ExamTopics

Question #1211 Topic 1

Refer to the exhibit. What does the host do when using the IPv4 Preferred function?

A. It forces the DNS server to provide the same IPv4 address at each renewal.

B. It requests the same IPv4 address when it renews its lease with the DHCP server. Most Voted

C. It prefers a pool of addresses when renewing the IPv4 host IP address.

D. It continues to use a statically assigned IPv4 address.

Correct Answer: B

Community vote distribution

B (100%)

https://www.examtopics.com/exams/cisco/200-301/view/9/ 7/28
12/26/24, 10:26 AM 200-301 Exam - Free Actual Q&As, Page 9 | ExamTopics

Question #1212 Topic 1

Refer to the exhibit. What is preventing host A from reaching the internet?

A. LAN and WAN network segments are different.

B. The domain name server is unreachable. Most Voted

C. The default gateway should be the first usable IP address.

D. IP address assignment is incorrect.

Correct Answer: B

Community vote distribution

B (100%)

https://www.examtopics.com/exams/cisco/200-301/view/9/ 8/28
12/26/24, 10:26 AM 200-301 Exam - Free Actual Q&As, Page 9 | ExamTopics

Question #1213 Topic 1

What are two capabilities provided by VRRP within a LAN network? (Choose two.)

A. redundancy Most Voted

B. granular QoS

C. load sharing Most Voted

D. dynamic routing updates

E. bandwidth optimization

Correct Answer: AC

Community vote distribution

AC (100%)

Question #1214 Topic 1

Which AP mode is used for capturing wireless traffic and forwarding that traffic to a PC that is running a packet analyzer?

A. bridge

B. monitor

C. rouge detector

D. sniffer Most Voted

Correct Answer: D

Community vote distribution

D (74%) B (26%)

https://www.examtopics.com/exams/cisco/200-301/view/9/ 9/28
12/26/24, 10:26 AM 200-301 Exam - Free Actual Q&As, Page 9 | ExamTopics

Question #1215 Topic 1

Refer to the exhibit. The IPv6 address for the LAN segment on router R2 must be configured using the EUI-64 format. When configured which ipv6

address is produced by the router?

A. 2001:db8:d955:1008:12D8:BAFE:FF01:1

B. 2001:db8:d955:1008:4598:785F:FE25:1

C. 2001:db8:d955:1008:1030:ABFF:FECC:1

D. 2001:db8:d955:1008:10D8:BAFF:FEC2:1 Most Voted

Correct Answer: D

Community vote distribution

D (100%)

https://www.examtopics.com/exams/cisco/200-301/view/9/ 10/28
12/26/24, 10:26 AM 200-301 Exam - Free Actual Q&As, Page 9 | ExamTopics

Question #1216 Topic 1

SIMULATION

Guidelines

This is a lab item in which tasks will be performed on virtual devices.

• Refer to the Tasks tab to view the tasks for this lab item.

• Refer to the Topology tab to access the device console(s) and perform the tasks.

• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.

• All necessary preconfigurations have been applied.

• Do not change the enable password or hostname for any device.

• Save your configurations to NVRAM before moving to the next item.

• Click Next at the bottom of the screen to submit this lab and move to the next question.

• When Next is clicked, the lab doses and cannot be reopened.

Topology

Tasks

Refer to the topology. All physical cabling is in place. Routers R3 and R4 are fully configured and inaccessible. Configure static routes for various

connectivity to the ISP and the LAN, which

resides on R4.

1. Configure a default route on R2 to the ISP

https://www.examtopics.com/exams/cisco/200-301/view/9/ 11/28
12/26/24, 10:26 AM 200-301 Exam - Free Actual Q&As, Page 9 | ExamTopics

2. Configure a default route on R1 to the ISP

3. Configure R2 with a route to the Server at 10.0.41.10

4. Configure R1 with a route to the LAN that prefers R3 as the primary path to the LAN

Correct Answer:

Question #1217 Topic 1

Which components are contained within a virtual machine?

A. physical resources, including the NIC, RAM, disk, and CPU

B. configuration files backed by physical resources from the Hypervisor Most Voted

C. applications running on the Hypervisor

D. processes running on the Hypervisor and a guest OS

Correct Answer: B

Community vote distribution

B (76%) A (18%) 6%

Question #1218 Topic 1

Which interface IP address serves as the tunnel source for CAPWAP packets from the WLC to an AP?

A. service

B. trunk

C. AP-manager Most Voted

D. virtual AP connection

Correct Answer: C

Community vote distribution

C (100%)

https://www.examtopics.com/exams/cisco/200-301/view/9/ 12/28
12/26/24, 10:26 AM 200-301 Exam - Free Actual Q&As, Page 9 | ExamTopics

Question #1219 Topic 1

What does a switch search for in the CAM table when forwarding a frame?

A. source MAC address and aging time

B. destination MAC address and flush time

C. source MAC address and source port

D. destination MAC address and destination port Most Voted

Correct Answer: D

Community vote distribution

D (100%)

Question #1220 Topic 1

Which port type does a lightweight AP use to connect to the wired network when configured in FlexConnect mode with local switching and VLAN

tagging?

A. trunk Most Voted

B. LAG

C. EtherChannel

D. access

Correct Answer: A

Community vote distribution

A (100%)

https://www.examtopics.com/exams/cisco/200-301/view/9/ 13/28
12/26/24, 10:26 AM 200-301 Exam - Free Actual Q&As, Page 9 | ExamTopics

Question #1221 Topic 1

Refer to the exhibit. PC A is communicating with another device at IP address 10.227.151.255. Through which router does router Y route the

traffic?

A. router A

B. router B

C. router C

D. router D Most Voted

Correct Answer: D

Community vote distribution

D (100%)

https://www.examtopics.com/exams/cisco/200-301/view/9/ 14/28
12/26/24, 10:26 AM 200-301 Exam - Free Actual Q&As, Page 9 | ExamTopics

Question #1222 Topic 1

Refer to the exhibit. VoIP is being implemented in the network using VLAN ID 73 and named "VoIP". Each user needs a Cisco IP phone at their

desk. Switchport e0/0 has been configured as an access port in the data VLAN. Cisco Discovery Protocol is enabled globally. Which command

sequence completed the configuration?

A. vlan73

name VoIP

e0/0

switchport voice vlan dot1p

B. vlan 73

name VoIP

e0/0

switchport trunk allowed vlan 72,73

switchport voice vlan 73

C. vlan 73

name VoIP

e0/0

switchport mode trunk

channel-group 73 mode active

D. vlan 73

name VoIP

e0/0

switchport voice vlan 73 Most Voted

Correct Answer: D

Community vote distribution

D (100%)

https://www.examtopics.com/exams/cisco/200-301/view/9/ 15/28
12/26/24, 10:26 AM 200-301 Exam - Free Actual Q&As, Page 9 | ExamTopics

Question #1223 Topic 1

Refer to the exhibit. Which IP route command created the best path for a packet destined for 10.10.10.3?

A. ip route 10.10.0.0 255.255.252.0 g0/0

B. ip route 10.10.10.0 255.255.255.240 g0/0 Most Voted

C. ip route 10.0.0.0 255.0.0.0 g0/0

D. ip route 10.10.10.1 255.255.255.255 g0/0

Correct Answer: B

Community vote distribution

B (100%)

Question #1224 Topic 1

Which cable type must be used when connecting a router and switch together using these criteria?

• Pins 1 and 2 are receivers and pins 3 and 6 are transmitters.

• Auto detection MDI-X is unavailable.

A. crossover

B. rollover

C. console

D. straight-through Most Voted

Correct Answer: D

Community vote distribution

D (58%) A (42%)

https://www.examtopics.com/exams/cisco/200-301/view/9/ 16/28
12/26/24, 10:26 AM 200-301 Exam - Free Actual Q&As, Page 9 | ExamTopics

Question #1225 Topic 1

Which protocol does a REST API use to communicate?

A. SSH

B. STP

C. SNMP

D. HTTP Most Voted

Correct Answer: D

Community vote distribution

D (100%)

Question #1226 Topic 1

Which interface on the WLC is limited to one when LAG is in use?

A. service

B. virtual

C. trunk

D. AP-manager Most Voted

Correct Answer: D

Community vote distribution

D (100%)

https://www.examtopics.com/exams/cisco/200-301/view/9/ 17/28
12/26/24, 10:26 AM 200-301 Exam - Free Actual Q&As, Page 9 | ExamTopics

Question #1227 Topic 1

Refer to the exhibit. A newly configured PC fails to connect to the internet by using TCP port 80 to www.cisco.com. Which setting must be

modified for the connection to work?

A. Subnet Mask Most Voted

B. DNS Servers

C. Default Gateway

D. DHCP Servers

Correct Answer: A

Community vote distribution

A (100%)

Question #1228 Topic 1

Which fact must the engineer consider when implementing syslog on a new network?

A. Syslog defines the software or hardware component that triggered the message.

B. There are 16 different logging levels (0-15).

C. The logging level defines the severity of a particular message. Most Voted

D. By default, all message levels are sent to the syslog server.

Correct Answer: C

Community vote distribution

C (100%)

https://www.examtopics.com/exams/cisco/200-301/view/9/ 18/28
12/26/24, 10:26 AM 200-301 Exam - Free Actual Q&As, Page 9 | ExamTopics

Question #1229 Topic 1

In what way does a network supervisor reduce maintenance costs while maintaining network integrity on a traditionally managed network?

A. They install an automated network-monitoring system to provide early warning of network issues.

B. They employ additional network administrators to proactively manage the network.

C. They use automation to centralize network-management tasks. Most Voted

D. They automate change-management processes that verify issue resolution.

Correct Answer: C

Community vote distribution

C (76%) A (24%)

Question #1230 Topic 1

Which type of wired port is required when an AP offers one unique SSID, passes client data and management traffic, and is in autonomous mode?

A. trunk Most Voted

B. default

C. access

D. LAG

Correct Answer: A

Community vote distribution

A (78%) C (22%)

https://www.examtopics.com/exams/cisco/200-301/view/9/ 19/28
12/26/24, 10:26 AM 200-301 Exam - Free Actual Q&As, Page 9 | ExamTopics

Question #1231 Topic 1

Refer to the exhibit. A network engineer must configure the WLC to allow only DHCP and DNS packets for User1 and User2. Which configuration

must be used?

A. Enable Web Authentication for 802.1X standard in the Layer 2 Security configuration

B. Enable Fallback Policy with MAC filtering under the Layer 3 Security configuration

C. Enable Web policy and Authentication in the Layer 3 Security configuration. Most Voted

D. Enable Web Authentication under the AAA Server configuration on the WLAN.

Correct Answer: C

Community vote distribution

C (89%) 11%

Question #1232 Topic 1

Which connection type is used when an engineer connects to an AP without a configured IP address or dial-up number to manage the device?

A. AUX

B. Ethernet

C. VIY

D. console Most Voted

Correct Answer: D

Community vote distribution

D (100%)

https://www.examtopics.com/exams/cisco/200-301/view/9/ 20/28
12/26/24, 10:26 AM 200-301 Exam - Free Actual Q&As, Page 9 | ExamTopics

Question #1233 Topic 1

What is a function of a firewall on an enterprise network?

A. It allows and denies ingress and egress traffic. Most Voted

B. It serves as a default gateway to hosts on the internet.

C. It processes traffic based on stateless inspection.

D. It acts as the intermediary device between the enterprise and its ISP.

Correct Answer: A

Community vote distribution

A (100%)

Question #1234 Topic 1

Which protocol is implemented when an organization must verify network performance, troubleshoot issues, and use an agent to communicate

between monitoring tools and end devices?

A. FIP

B. NIP

C. NFS

D. SNMP Most Voted

Correct Answer: D

Community vote distribution

D (100%)

Question #1235 Topic 1

What is a difference between an IPv6 multicast address and an IPv6 anycast address?

A. An IPv6 multicast address uses the prefix 2002::/15 and forwards to one destination, and an IPv6 anycast address uses the prefix ff00:/8

and forwards to any destination in a group.

B. A packet sent to an IPv6 multicast address is delivered to one or more destinations at once, but a packet sent to an IPv6 anycast address is

routed to the closest interface with that address. Most Voted

C. IPV6 multicast addresses are used to transition from IPv4 to IPv6, and IPv6 anycast addresses are used for address aggregation in an IPv6-

only environment.

D. An IPV6 multicast address is assigned to numerous interfaces within a subnet, but an IPv6 anycast address is used for a predefined group

of nodes in an all-IPv6 routers group.

Correct Answer: B

Community vote distribution

B (100%)

https://www.examtopics.com/exams/cisco/200-301/view/9/ 21/28
12/26/24, 10:26 AM 200-301 Exam - Free Actual Q&As, Page 9 | ExamTopics

Question #1236 Topic 1

Which syslog message logging level displays interface line protocol up/down events?

A. informational

B. alerts

C. debugging

D. notifications Most Voted

Correct Answer: D

Community vote distribution

D (100%)

Question #1237 Topic 1

Which device protects an internal network from the Internet?

A. router

B. firewall Most Voted

C. access point

D. Layer 2 switch

Correct Answer: B

Community vote distribution

B (100%)

Question #1238 Topic 1

Which encryption mode is used when a packet is sent from a site-to-site VPN connection where the source and destination IP address portion of a

packet is unencrypted?

A. PPTP

B. Secure Shell

C. Transport Most Voted

D. PPPoE

Correct Answer: C

Community vote distribution

C (100%)

https://www.examtopics.com/exams/cisco/200-301/view/9/ 22/28
12/26/24, 10:26 AM 200-301 Exam - Free Actual Q&As, Page 9 | ExamTopics

Question #1239 Topic 1

What is a reason why an administrator would choose to implement an automated network management approach?

A. Enable "box by box" configuration and deployment.

B. Decipher simple password policies.

C. Reduce inconsistencies in the network configuration. Most Voted

D. Increase recurrent management costs.

Correct Answer: C

Community vote distribution

C (100%)

Question #1240 Topic 1

Refer to the exhibit. The router R1 is in the process of being configured. Routers R2 and R3 are configured correctly for the new environment.

Which two commands must be configured on R1 for PC1 to communicate to all PCs on the 10.10.10.0/24 network? (Choose two.)

A. ip route 10.10.10.0 255.255.255.0 192.168.2.3

ip route 10.10.10.10 255.255.255.255 192.168.2.2 Most Voted

B. ip route 10.10.10.0 255.255.255.0 192.168.2.2

ip route 10.10.2.2 255.255.255.255 10.10.10.10

C. ip route 10.10.10.0 255.255.255.0 192.168.2.3

ip route 10.10.10.8 255.255.255.252 g0/0

D. ip route 10.10.10.0 255.255.255.248 192.168.2.2

ip route 10.10.2.8 255.255.255.252 g0/1

Correct Answer: A

Community vote distribution

A (100%)

https://www.examtopics.com/exams/cisco/200-301/view/9/ 23/28
12/26/24, 10:26 AM 200-301 Exam - Free Actual Q&As, Page 9 | ExamTopics

Question #1241 Topic 1

Refer to the exhibit. A packet sourced from 172.18.33.2 is destined for 172.18.32.38. Where does the router forward the packet?

A. 10.1.1.1

B. 10.1.1.3

C. Loopback0

D. GigabitEthernet0/0 Most Voted

Correct Answer: D

Community vote distribution

D (100%)

https://www.examtopics.com/exams/cisco/200-301/view/9/ 24/28
12/26/24, 10:26 AM 200-301 Exam - Free Actual Q&As, Page 9 | ExamTopics

Question #1242 Topic 1

Refer to the exhibit. An administrator is configuring a new WLAN for a wireless network that has these requirements:

• Dual-band clients that connect to the WLAN must be directed to the 5-GHz spectrum.

• Wireless clients on this WLAN must be able to apply VLAN settings on the returned RADIUS attributes.

Which two actions meet these requirements? (Choose two.)

A. Enable the Client Band Select option. Most Voted

B. Enable the Coverage Hole Detection option.

C. Enable the Allow AAA Override option. Most Voted

D. Set the MFP Client Protection option to Required.

E. Enable the Aironet IE option

Correct Answer: AC

Community vote distribution

AC (100%)

Question #1243 Topic 1

How does a network administrator securely manage an AP in lightweight mode?

A. using the AP GUI via an in-band SSH connection

B. using the CLI via an out-of-band connection

C. using the CLI via a virtual interface with SSH

D. using the WLC GUI via HTTPS Most Voted

Correct Answer: D

Community vote distribution

D (100%)

https://www.examtopics.com/exams/cisco/200-301/view/9/ 25/28
12/26/24, 10:26 AM 200-301 Exam - Free Actual Q&As, Page 9 | ExamTopics

Question #1244 Topic 1

Which type of protocol is VRRP?

A. allows two or more routers to act as a default gateway Most Voted

B. uses Cisco-proprietary First Hop Redundancy Protocol

C. uses a destination IP address 224.0.0.102 for router-to-router communication

D. uses dynamic IP address assignment

Correct Answer: A

Community vote distribution

A (100%)

Question #1245 Topic 1

Refer to the exhibit. The switch cat9k-acc-1 connects users to the campus LAN. Printing services are inaccessible through the network. Which

interface issue is causing the connectivity problems?

A. A bad checksum is causing Ethernet frames to drop.

B. Excessive collisions are causing dropped frames.

C. A large number of broadcast packets are resulting in a port reset. Most Voted

D. The interface output queue cannot process the Ethernet frames.

Correct Answer: C

Community vote distribution

C (71%) A (29%)

https://www.examtopics.com/exams/cisco/200-301/view/9/ 26/28
12/26/24, 10:26 AM 200-301 Exam - Free Actual Q&As, Page 9 | ExamTopics

Question #1246 Topic 1

Which standard is required when more than one distribution system port and only one IP address are configured for a Cisco WLC?

A. 802.3ad Most Voted

B. 802.1q

C. 802.1d

D. 802.1af

Correct Answer: A

Community vote distribution

A (75%) B (25%)

Question #1247 Topic 1

Which capability does TFTP provide?

A. loads configuration files on systems without data storage devices Most Voted

B. provides authentication for data communications over a private data network

C. provides encryption mechanisms for file transfer across a WAN

D. provides secure file access within the LAN

Correct Answer: A

Community vote distribution

A (100%)

Question #1248 Topic 1

Which action protects a network from VLAN hopping attacks?

A. Implement port security on internet-facing VLANs.

B. Change the native VLAN to an unused VLAN ID. Most Voted

C. Enable dynamic ARP inspection.

D. Configure an ACL to prevent traffic from changing VLANs.

Correct Answer: B

Community vote distribution

B (100%)

https://www.examtopics.com/exams/cisco/200-301/view/9/ 27/28
12/26/24, 10:26 AM 200-301 Exam - Free Actual Q&As, Page 9 | ExamTopics

Question #1249 Topic 1

What should a network administrator consider when deciding to implement automation?

A. Automated systems may have difficulty expanding network changes at scale.

B. Network automation typically is limited to the configuration and management of virtual devices within a network.

C. Network automation typically increases enterprise management operating costs.

D. Manual changes frequently lead to configuration errors and inconsistencies. Most Voted

Correct Answer: D

Community vote distribution

D (100%)

Question #1250 Topic 1

Company has decided to require multifactor authentication for all systems. Which set of parameters meets the requirement?

A. personal 10-digit PIN and RSA certificate Most Voted

B. complex password and personal 10-digit PIN

C. password of 8 to 15 characters and personal 12-digit PIN

D. fingerprint scanning and facial recognition

Correct Answer: A

Community vote distribution

A (100%)

 Previous Questions Next Questions 

Browse atleast 50% to increase passing rate

Viewing page 9 out of 12 pages.

Viewing questions 401-450 out of 1395 questions

https://www.examtopics.com/exams/cisco/200-301/view/9/ 28/28