ASME B16.

5
Templates for drilling class 1500 pipe flanges

Flange

Drilling

Nominal pipe Outside diameter of Diameter of bolt Diameter of bolt

Number of bolts. Diameter of bolts, IN.
size (NPS) flange, O circle, W holes, IN.

1/2 120 82,6 7/8 4 3/4

3/4 130 88,9 7/8 4 3/4
1 150 101,6 1 4 7/8
1 1/4 160 111,1 1 4 7/8
1 1/2 180 123,8 1 1/8 4 1
2 215 165,1 1 8 7/8
2 1/2 245 190,5 1 1/8 8 1
3 265 203,2 1 1/4 8 1 1/8
4 310 241,3 1 3/8 8 1 1/4
5 375 292,1 1 5/8 8 1 1/2
6 395 317,5 1 1/2 12 1 3/8
8 485 393,7 1 3/4 12 1 5/8
10 585 482,6 2 12 1 7/8
12 675 571,5 2 1/8 16 2
14 750 635,0 2 3/8 16 2 1/4
16 825 704,8 2 5/8 16 2 1/2
18 915 774,7 2 7/8 16 2 3/4
20 985 831,8 3 1/8 16 3
24 1170 990,6 3 5/8 16 3 1/2
ASME B16.5
Templates for drilling class 1500 pipe flanges

Point height [Note (1)]

Stud Bolt With Nuts

Length of bolts, L

7-mm raised face Male and female/tongue and groove Ring joint

110 100 110

115 110 115
125 120 125
125 120 125
140 135 140
145 140 145
160 150 160
180 170 180
195 190 195
250 240 250
260 255 265
290 285 300
335 330 345
375 370 385
405 400 425
445 440 470
495 490 525
540 535 565
615 610 650

The values, unless otherwise indicated, are to be considered in millimeters

Note 1: The length of the stud bolt does not include the height of the points.
ASME B16.5
Dimensions of class 1500 flanges

Threaded Slip-On Welding

Socket Welding
(NPS 1/2 to 3 Only)

Length through hub

Outside Minimum Hub diameter Threaded /

Nominal pipe Diameter Welding Number
diameter of thickness beginning of chamfer slip-on /socket Lapped, Y
size (NPS) of hub, X neck ,Y of bolts.
flange, O of flange, tf welding neck, Ah welding, Y

1/2 120 22,3 38 21,3 32 32 60 4

3/4 130 25,4 44 26,7 35 35 70 4
1 150 28,6 52 33,4 41 41 73 4
1 1/4 160 28,6 64 42,2 41 41 73 4
1 1/2 180 31,8 70 48,3 44 44 83 4
2 215 38,1 105 60,3 57 57 102 8
2 1/2 245 41,3 124 73,9 64 64 105 8
3 265 47,7 133 101,6 --- 73 117 8
4 310 54 162 114,3 --- 90 124 8
5 375 73,1 197 141,3 --- 105 156 8
6 395 82,6 229 168,3 --- 119 171 12
8 485 92,1 292 219,1 --- 143 213 12
10 585 108 368 273,0 --- 178 254 12
12 675 123,9 451 323,8 --- 219 283 16
14 750 133,4 495 355,6 --- 241 298 16
16 825 146,1 552 406,4 --- 260 311 16
18 915 162 597 457,0 --- 276 327 16
20 985 177,8 641 508,0 --- 292 356 16
24 1170 203,2 762 610,0 --- 330 406 16
ASME B16.5
Dimensions of class 1500 flanges

Welding Neck Lapped

Blind

Bore

Minimum thread Minimum Corner bore radius Minimum

Minimum Welding neck/socket Depth
length threaded slip-on/socket of lapped flange counterbore
lapped, B welding, B of socket, D
flange, T welding, B and pipe, r threaded flange, Q

23 22,2 22,9 To be specified by the purchaser 3 23,6 10

26 27,7 28,2 To be specified by the purchaser 3 29 11
29 34,5 34,9 To be specified by the purchaser 3 35,8 13
31 43,2 43,7 To be specified by the purchaser 5 44,4 14
32 49,5 50,0 To be specified by the purchaser 6 50,6 16
39 61,9 62,5 To be specified by the purchaser 8 63,5 17
48 74,6 75,4 To be specified by the purchaser 8 76,2 19
--- --- 104,1 To be specified by the purchaser 10 --- ---
--- --- 116,8 To be specified by the purchaser 11 --- ---
--- --- 144,4 To be specified by the purchaser 11 --- ---
--- --- 171,4 To be specified by the purchaser 13 --- ---
--- --- 222,2 To be specified by the purchaser 13 --- ---
--- --- 277,4 To be specified by the purchaser 13 --- ---
--- --- 328,2 To be specified by the purchaser 13 --- ---
--- --- 360,2 To be specified by the purchaser 13 --- ---
--- --- 411,2 To be specified by the purchaser 13 --- ---
--- --- 462,3 To be specified by the purchaser 13 --- ---
--- --- 514,4 To be specified by the purchaser 13 --- ---
--- --- 616 To be specified by the purchaser 13 --- ---

The values, unless otherwise indicated, are to be considered in millimeters

Note 1: This dimension is for the large end of the hub, which may be straight or tapered. Taper shall not exceed 7 deg on
threaded, slip-on, socket-welding, and lapped flanges. This dimension is defined as the diameter at the intersection
between the hub taper and back face of the flange.
ASME B16.5
Templates for drilling class 2500 pipe flanges

Flange

Drilling

Nominal pipe Outside diameter of Diameter of bolt Diameter of bolt

Number of bolts. Diameter of bolts, IN.
size (NPS) flange, O circle, W holes, IN.

1/2 135 88,9 7/8 4 3/4

3/4 140 95,2 7/8 4 3/4
1 160 108,0 1 4 7/8
1 1/4 185 130,2 1 1/8 4 1
1 1/2 205 146,0 1 1/4 4 1 1/8
2 235 171,4 1 1/8 8 1
2 1/2 265 196,8 1 1/4 8 1 1/8
3 305 228,6 1 3/8 8 1 1/4
4 355 273,0 1 5/8 8 1 1/2
5 420 323,8 1 7/8 8 1 3/4
6 485 368,3 2 1/8 8 2
8 550 438,2 2 1/8 12 2
10 675 549,8 2 5/8 12 2 1/2
12 760 619,1 2 7/8 12 2 3/4
ASME B16.5
Templates for drilling class 2500 pipe flanges

Point height [Note (1)]

Stud Bolt With Nuts

Length of bolts, L

7-mm raised face Male and female/tongue and groove Ring joint

120 115 120

125 120 125
140 135 140
150 145 150
170 165 170
180 170 180
195 190 205
220 215 230
255 250 260
300 290 310
345 335 355
380 375 395
490 485 510
540 535 560

The values, unless otherwise indicated, are to be considered in millimeters

Note 1: The length of the stud bolt does not include the height of the points.
ASME B16.5
Dimensions of class 2500 flanges

Threaded
(NPS 1/2 to 2 1/2 Only)

Lapped

Length through hub

Hub diam. Beginning

Nominal pipe Outside diam. Min. Thickness Diam. Welding
of chamfer welding Threaded, Y Lapped, Y
size (NPS) of flange, O of flange, tf of hub, X neck ,Y
neck, Ah

1/2 135 30,2 43 21,3 40 40 73

3/4 140 31,8 51 26,7 43 43 79
1 160 35,0 57 33,4 48 48 89
1 1/4 185 38,1 73 42,2 52 52 95
1 1/2 205 44,5 79 48,3 60 60 111
2 235 50,9 95 60,3 70 70 127
2 1/2 265 57,2 114 73,9 79 79 143
3 305 66,7 133 101,6 --- 92 168
4 355 76,2 165 114,3 --- 108 190
5 420 92,1 203 141,3 --- 130 229
6 485 108,0 235 168,3 --- 152 273
8 550 127,0 305 219,1 --- 178 318
10 675 165,1 375 273,0 --- 229 419
12 760 184,2 441 323,8 --- 254 464
ASME B16.5
Dimensions of class 2500 flanges

Blind

Welding Neck

Bore

Corner bore radius

Minimum thread length Minimum counterbore
Min. lapped, B Welding neck, B of lapped flange
threaded flange, T threaded flange, Q
and pipe, r

29 22,9 To be specified by the purchaser 3 23,6

32 28,2 To be specified by the purchaser 3 29
35 34,9 To be specified by the purchaser 3 35,8
39 43,7 To be specified by the purchaser 5 44,4
45 50,0 To be specified by the purchaser 6 50,6
51 62,5 To be specified by the purchaser 8 63,5
58 75,4 To be specified by the purchaser 8 76,2
--- 104,1 To be specified by the purchaser 10 ---
--- 116,8 To be specified by the purchaser 11 ---
--- 144,4 To be specified by the purchaser 11 ---
--- 171,4 To be specified by the purchaser 13 ---
--- 222,2 To be specified by the purchaser 13 ---
--- 277,4 To be specified by the purchaser 13 ---
--- 328,2 To be specified by the purchaser 13 ---

The values, unless otherwise indicated, are to be considered in millimeters

ASME B16.5
Templates for drilling class 600 pipe flanges

Flange

Drilling

Nominal pipe Outside diameter of Diameter of bolt Diameter of bolt

Number of bolts. Diameter of bolts, IN.
size (NPS) flange, O circle, W holes, IN.

1/2 95 66,7 5/8 4 1/2

3/4 115 82,6 3/4 4 5/8
1 125 88,9 3/4 4 5/8
1 1/4 135 98,4 3/4 4 5/8
1 1/2 155 114,3 7/8 4 3/4
2 165 127 3/4 8 5/8
2 1/2 190 149,2 7/8 8 3/4
3 210 168,3 7/8 8 3/4
3 1/2 230 184,2 1 8 7/8
4 275 215,9 1 8 7/8
5 330 266,7 1 1/8 8 1
6 355 292,1 1 1/8 12 1
8 420 349,2 1 1/4 12 1 1/8
10 510 431,8 1 3/8 16 1 1/4
12 560 489 1 3/8 20 1 1/4
14 605 527 1 1/2 20 1 3/8
16 685 603,2 1 5/8 20 1 1/2
18 745 654 1 3/4 20 1 5/8
20 815 723,9 1 3/4 24 1 5/8
24 940 838,2 2 24 1 7/8
ASME B16.5
Templates for drilling class 600 pipe flanges

Point height [Note (1)]

Stud Bolt With Nuts

Length of bolts, L

7-mm raised face Male and female/tongue and groove Ring joint

75 70 75
90 85 90
90 85 90
95 90 95
110 100 110
110 100 110
120 115 120
125 120 125
140 135 140
145 140 145
165 160 165
170 165 170
190 185 195
215 210 215
220 215 220
235 230 235
255 250 255
275 265 275
285 280 290
330 325 335

The values, unless otherwise indicated, are to be considered in millimeters

Note 1: The length of the stud bolt does not include the height of the points.
ASME B16.5
Dimensions of class 600 flanges

Threaded Slip-On Welding

Socket Welding
(NPS 1/2 to 3 Only)

Length through hub

Outside Minimum Hub diameter

Nominal pipe Diameter Threaded / slip-on / Number
diameter of thickness beginning of chamfer Lapped, Y
size (NPS) of hub, X socket welding, Y of bolts.
flange, O of flange, tf welding neck, Ah

1/2 95 14,3 38 21,3 22 22 52

3/4 115 15,9 48 26,7 25 25 57
1 125 17,5 54 33,4 27 27 62
1 1/4 135 20,7 64 42,2 29 29 67
1 1/2 155 22,3 70 48,3 32 32 70
2 165 25,4 84 60,3 37 37 73
2 1/2 190 28,6 100 73,9 41 41 79
3 210 31,8 117 88,9 46 46 83
3 1/2 230 35 133 101,6 49 49 86
4 275 38,1 152 114,3 54 54 102
5 330 44,5 189 141,3 60 60 114
6 355 47,7 222 168,3 67 67 117
8 420 55,6 273 219,1 76 76 133
10 510 63,5 343 273,0 86 111 152
12 560 66,7 400 323,8 92 117 156
14 605 69,9 432 355,6 94 127 165
16 685 76,2 495 406,4 106 140 178
18 745 82,6 546 457,0 117 152 184
20 815 88,9 610 508,0 127 165 190
24 940 101,6 718 610,0 140 184 203
ASME B16.5
Dimensions of class 600 flanges

Welding Neck Lapped

Blind

Bore

Minimum thread Minimum Corner bore radius Minimum

Minimum Welding neck/socket Depth
length threaded slip-on/socket of lapped flange counterbore
lapped, B welding, B of socket, D
flange, T welding, B and pipe, r threaded flange, Q

16 22,2 22,9 To be specified by the purchaser 3 23,6 10

16 27,7 28,2 To be specified by the purchaser 3 29 11
18 34,5 34,9 To be specified by the purchaser 3 35,8 13
21 43,2 43,7 To be specified by the purchaser 5 44,4 14
23 49,5 50,0 To be specified by the purchaser 6 50,6 16
29 61,9 62,5 To be specified by the purchaser 8 63,5 17
32 74,6 75,4 To be specified by the purchaser 8 76,2 19
35 90,7 91,4 To be specified by the purchaser 10 92,2 21
40 103,4 104,1 To be specified by the purchaser 10 104,9 ---
42 116,1 116,8 To be specified by the purchaser 11 117,6 ---
48 143,8 144,4 To be specified by the purchaser 11 144,4 ---
51 170,7 171,4 To be specified by the purchaser 13 171,4 ---
--- 221,5 222,2 To be specified by the purchaser 13 --- ---
--- 276,2 277,4 To be specified by the purchaser 13 --- ---
--- 327 328,2 To be specified by the purchaser 13 --- ---
--- 359,2 360,2 To be specified by the purchaser 13 --- ---
--- 410,5 411,2 To be specified by the purchaser 13 --- ---
--- 461,8 462,3 To be specified by the purchaser 13 --- ---
--- 513,1 514,4 To be specified by the purchaser 13 --- ---
--- 616 616 To be specified by the purchaser 13 --- ---

The values, unless otherwise indicated, are to be considered in millimeters

Note 1: This dimension is for the large end of the hub, which may be straight or tapered. Taper shall not exceed 7 deg on
threaded, slip-on, socket-welding, and lapped flanges. This dimension is defined as the diameter at the intersection
between the hub taper and back face of the flange.
ASME B16.5
Templates for drilling class 150 pipe flanges

Flange

Drilling

Nominal pipe Outside diameter of Diameter of bolt Diameter of bolt

Number of bolts. Diameter of bolts, IN.
size (NPS) flange, O circle, W holes, IN.

1/2 90 60,3 5/8 4 1/2

3/4 100 69,9 5/8 4 1/2
1 110 79,4 5/8 4 1/2
1 1/4 115 88,9 5/8 4 1/2
1 1/2 125 98,4 5/8 4 1/2
2 150 120,7 3/4 4 5/8
2 1/2 180 139,7 3/4 4 5/8
3 190 152,4 3/4 4 5/8
3 1/2 215 177,8 3/4 8 5/8
4 230 190,5 3/4 8 5/8
5 255 215,9 7/8 8 3/4
6 280 241,3 7/8 8 3/4
8 345 298,5 7/8 8 3/4
10 405 362,0 1 12 7/8
12 485 431,8 1 12 7/8
14 535 476,3 1 1/8 12 1
16 595 539,8 1 1/8 16 1
18 635 577,9 1 1/4 16 1 1/8
20 700 635,0 1 1/4 20 1 1/8
24 815 749,3 1 3/8 20 1 1/4
ASME B16.5
Templates for drilling class 150 pipe flanges

Machine Bolt With Nuts

Point height [Note (1)]

Stud Bolt With Nuts

Length of bolts, L
Stud bolts Machine bolts

2-mm raised face Ring joint 2-mm raised face

55 --- 50
65 --- 50
65 75 55
70 85 55
70 85 65
85 95 70
90 100 75
90 100 75
90 100 75
90 100 75
95 110 85
100 115 85
110 120 90
115 125 100
120 135 100
135 145 115
135 145 115
145 160 125
160 170 140
170 185 150

The values, unless otherwise indicated, are to be considered in millimeters

Note 1: The length of the stud bolt does not include the height of the points.
ASME B16.5
Dimensions of class 150 flanges

Threaded Slip-On Welding

Socket Welding
(NPS 1/2 to 3 Only)

Length through hub

Hub diameter
Nominal Outside Minimum Minimum Threaded /
Diameter beginning Lapped, Welding
pipe size diameter thickness of thickness lap slip-on /socket
of hub, X of chamfer Y neck, Y
(NPS) of flange, O flange, tf joint, tf welding, Y
welding neck, Ah
1/2 90 9,6 11,2 30 21,3 14 16 46
3/4 100 11,2 12,7 38 26,7 14 16 51
1 110 12,7 14,3 49 33,4 16 17 54
1 1/4 115 14,3 15,9 59 42,2 19 21 56
1 1/2 125 15,9 17,5 65 48,3 21 22 60
2 150 17,5 19,1 78 60,3 24 25 62
2 1/2 180 20,7 22,3 90 73,9 27 29 68
3 190 22,3 23,9 108 88,9 29 30 68
3 1/2 215 22,3 23,9 122 101,6 30 32 70
4 230 22,3 23,9 135 114,3 32 33 75
5 255 22,3 23,9 164 141,3 35 36 87
6 280 23,9 25,4 192 168,3 38 40 87
8 345 27,0 28,6 246 219,1 43 44 100
10 405 28,6 30,2 305 273,0 48 49 100
12 485 30,2 31,8 365 323,8 54 56 113
14 535 33,4 35 400 355,6 56 79 125
16 595 35 36,6 457 406,4 62 87 125
18 635 38,1 39,7 505 457,0 67 97 138
20 700 41,3 42,9 559 508,0 71 103 143
24 815 46,1 47,7 663 610,0 81 111 151
ASME B16.5
Dimensions of class 150 flanges

Welding Neck Lapped

Blind

Bore

Minimum thread Minimum Welding Corner bore

Minimum Depth
length slip-on/socket neck/socket radius of lapped
lapped, B of socket, D
threaded, T welding, B welding, B flange and pipe, r

16 22,2 22,9 15,8 3 10

16 27,7 28,2 20,9 3 11
17 34,5 34,9 26,6 3 13
21 43,2 43,7 35,1 5 14
22 49,5 50 40,9 6 16
25 61,9 62,5 52,5 8 17
29 74,6 75,4 62,7 8 19
30 90,7 91,4 77,9 10 21
32 103,4 104,1 90,1 10 ---
33 116,1 116,8 102,3 11 ---
36 143,8 144,4 128,2 11 ---
40 170,7 171,4 154,1 13 ---
221,5 222,2 202,7 13 ---
276,2 277,4 254,6 13 ---
327 328,2 304,8 13 ---
359,2 360,2 To be specified by the purchaser 13 ---
410,5 411,2 To be specified by the purchaser 13 ---
461,8 462,3 To be specified by the purchaser 13 ---
513,1 514,4 To be specified by the purchaser 13 ---
616 616 To be specified by the purchaser 13 ---

The values, unless otherwise indicated, are to be considered in millimeters

Note 1: This dimension is for the large end of the hub, which may be straight or tapered. Taper shall not exceed 7 deg on
threaded, slip-on, socket-welding, and lapped flanges. This dimension is defined as the diameter at the intersection
between the hub taper and back face of the flange.
ASME B16.5
Templates for drilling class 300 pipe flanges

Flange

Drilling

Nominal pipe Outside diameter of Diameter of bolt Diameter of bolt

Number of bolts. Diameter of bolts, IN.
size (NPS) flange, O circle, W holes, IN.

1/2 95 66,7 5/8 4 1/2

3/4 115 82,6 3/4 4 5/8
1 125 88,9 3/4 4 5/8
1 1/4 135 98,4 3/4 4 5/8
1 1/2 155 114,3 7/8 4 3/4
2 165 127,0 3/4 8 5/8
2 1/2 190 149,2 7/8 8 3/4
3 210 168,3 7/8 8 3/4
3 1/2 230 184,2 7/8 8 3/4
4 255 200,0 7/8 8 3/4
5 280 235,0 7/8 8 3/4
6 320 269,9 7/8 12 3/4
8 380 330,2 1 12 7/8
10 445 387,4 1 1/8 16 1
12 520 450,8 1 1/4 16 1 1/8
14 585 514,4 1 1/4 20 1 1/8
16 650 571,5 1 3/8 20 1 1/4
18 710 628,6 1 3/8 24 1 1/4
20 775 685,8 1 3/8 24 1 1/4
24 915 812,8 1 5/8 24 1 1/2
ASME B16.5
Templates for drilling class 300 pipe flanges

Machine Bolt With Nuts

Point height [Note (1)]

Stud Bolt With Nuts

Length of bolts, L
Stud bolts Machine bolts

2-mm raised face Ring joint 2-mm raised face

65 75 55
75 90 65
75 90 65
85 95 70
90 100 75
90 100 75
100 115 85
110 120 90
110 125 95
115 125 95
120 135 110
120 140 110
140 150 120
160 170 140
170 185 145
180 190 160
190 205 165
195 210 170
205 220 185
230 255 205

The values, unless otherwise indicated, are to be considered in millimeters

Note 1: The length of the stud bolt does not include the height of the points.
ASME B16.5
Dimensions of class 300 flanges

Threaded Slip-On Welding

Socket Welding
(NPS 1/2 to 3 Only)

Length through hub

Hub diameter
Nominal Outside Minimum Minimum Threaded /
Diameter beginning Lapped, Welding
pipe size diameter thickness of thickness lap slip-on /socket
of hub, X of chamfer Y neck, Y
(NPS) of flange, O flange, tf joint, tf welding, Y
welding neck, Ah
1/2 95 12,7 14,3 38 21,3 21 22 51
3/4 115 14,3 15,9 48 26,7 24 25 56
1 125 15,9 17,5 54 33,4 25 27 60
1 1/4 135 17,5 19,1 64 42,2 25 27 64
1 1/2 155 19,1 20,7 70 48,3 29 30 67
2 165 20,7 22,3 84 60,3 32 33 68
2 1/2 190 23,9 25,4 100 73,9 37 38 75
3 210 27 28,6 117 88,9 41 43 78
3 1/2 230 28,6 30,2 133 101,6 43 44 79
4 255 30,2 31,8 146 114,3 46 48 84
5 280 33,4 35 178 141,3 49 51 97
6 320 35,0 36,6 206 168,3 51 52 97
8 380 39,7 41,3 260 219,1 60 62 110
10 445 46,1 47,7 321 273,0 65 95 116
12 520 49,3 50,8 375 323,8 71 102 129
14 585 52,4 54 425 355,6 75 111 141
16 650 55,6 57,2 483 406,4 81 121 144
18 710 58,8 60,4 533 457,0 87 130 157
20 775 62 63,5 587 508,0 94 140 160
24 915 68,3 69,9 702 610,0 105 152 167

68
ASME B16.5
Dimensions of class 300 flanges

Welding Neck Lapped

Blind

Bore

Minimum thread Minimum Welding Corner bore

Minimum Depth Depth
length slip-on/socket neck/socket radius of lapped
lapped, B of socket, D of socket, D
threaded, T welding, B welding, B flange and pipe, r

16 22,2 22,9 15,8 3 23,6 10

16 27,7 28,2 20,9 3 29 11
18 34,5 34,9 26,6 3 35,8 13
21 43,2 43,7 35,1 5 44,4 14
23 49,5 50 40,9 6 50,3 16
29 61,9 62,5 52,5 8 63,5 17
32 74,6 75,4 62,7 8 76,2 19
32 90,7 91,4 77,9 10 92,2 21
37 103,4 104,1 90,1 10 104,9 ---
37 116,1 116,8 102,3 11 117,6 ---
43 143,8 144,4 128,2 11 144,4 ---
47 170,7 171,4 154,1 13 171,4 ---
221,5 222,2 202,7 13 222,2 ---
276,2 277,4 254,6 13 276,2 ---
327 328,2 304,8 13 328,6 ---
359,2 360,2 To be specified by the purchaser 13 360,4 ---
410,5 411,2 To be specified by the purchaser 13 411,2 ---
461,8 462,3 To be specified by the purchaser 13 462 ---
513,1 514,4 To be specified by the purchaser 13 512,8 ---
616 616 To be specified by the purchaser 13 614,4 ---

The values, unless otherwise indicated, are to be considered in millimeters

Note 1: This dimension is for the large end of the hub, which may be straight or tapered. Taper shall not exceed 7 deg on
threaded, slip-on, socket-welding, and lapped flanges. This dimension is defined as the diameter at the intersection
between the hub taper and back face of the flange.

69
ASME B16.5
Templates for drilling class 900 pipe flanges

Flange

Drilling

Nominal pipe Outside diameter of Diameter of bolt Diameter of bolt

Number of bolts. Diameter of bolts, IN.
size (NPS) flange, O circle, W holes, IN.

3 240 190,5 1 8 7/8

4 290 235,0 1 1/4 8 1 1/8
5 350 279,4 1 3/8 8 1 1/4
6 380 317,5 1 1/4 12 1 1/8
8 470 393,7 1 1/2 12 1 3/8
10 545 469,9 1 1/2 16 1 3/8
12 610 533,4 1 1/2 20 1 3/8
14 640 558,8 1 5/8 20 1 1/2
16 705 616,0 1 3/4 20 1 5/8
18 785 685,8 2 20 1 7/8
20 855 749,3 2 1/8 20 2
24 1040 901,7 2 5/8 20 2 1/2
ASME B16.5
Templates for drilling class 900 pipe flanges

Point height [Note (1)]

Stud Bolt With Nuts

Length of bolts, L

7-mm raised face Male and female/tongue and groove Ring joint

145 140 145

170 165 170
190 185 190
190 185 195
220 215 220
235 230 235
255 250 255
275 265 280
285 280 290
325 320 335
350 345 360
440 430 455

The values, unless otherwise indicated, are to be considered in millimeters

Note 1: The length of the stud bolt does not include the height of the points.
ASME B16.5
Dimensions of class 900 flanges
x

tf tf

tf tf
Blind

Welding Neck

Hub diameter
Outside Minimum
Nominal pipe Diameter beginning
diameter thickness Welding neck , Y Welding neck, B
size (NPS) of hub, x of chamfer
of flange, O of flange, tf
welding neck, Ah
3 240 38,1 127 88,9 102 To be specified by the purchaser
4 290 44,5 159 114,3 114 To be specified by the purchaser
5 350 50,8 190 141,3 127 To be specified by the purchaser
6 380 55,6 235 168,3 140 To be specified by the purchaser
8 470 63,5 298 219,1 162 To be specified by the purchaser
10 545 69,9 368 273,0 184 To be specified by the purchaser
12 610 79,4 419 323,8 200 To be specified by the purchaser
14 640 85,8 451 355,6 213 To be specified by the purchaser
16 705 88,9 508 406,4 216 To be specified by the purchaser
18 785 101,6 565 457,0 229 To be specified by the purchaser
20 855 108 622 508,0 248 To be specified by the purchaser
24 1040 139,7 749 610,0 292 To be specified by the purchaser

The values, unless otherwise indicated, are to be considered in millimeters

ASME B16.5
Dimensions of facings (other than ring joints, all pressure rating classes)

End Flange Facings

Flange Thickness and Center-to-End Dimensions
Classes 150 through 2500
ASME B16.5
Dimensions of facings (other than ring joints, all pressure rating classes)

End Flange Facings

Flange Thickness and End-to-End Dimensions
Lapped Joints
ASME B16.5
Dimensions of facings (other than ring joints, all pressure rating classes)

Outside diameter Outside diameter

Raised face Inside

Nominal Inside diameter Large female Small
large male Small male, Small diameter of Small
pipe size of small tongue and large female, X
and large S [note 1] tongue, T large and small groove, Y
(NPS) [note 1] groove, W [note 1]
tongue, R tongue, U
1/2 34,9 18,3 35,1 25,4 --- 36,5 19,9 36,5
3/4 42,9 23,8 42,9 33,3 --- 44,4 25,4 44,4
1 50,8 30,2 47,8 38,1 --- 52,4 31,8 49,2
1 1/4 63,5 38,1 57,2 47,6 --- 65,1 39,7 58,7
1 1/2 73 44,4 63,5 54 --- 74,6 46 65,1
2 92,1 57,2 82,6 73 --- 93,7 58,8 84,1
2 1/2 104,8 68,3 95,2 85,7 --- 106,4 69,8 69,8
3 127 84,1 117,5 108 --- 128,6 85,7 119,1
3 1/2 139,7 96,8 130,2 120,6 --- 141,3 98,4 131,8
4 157,2 109,5 144,5 131,8 --- 158,8 111,1 146
5 185,7 136,5 173 160,3 --- 187,3 138,1 174,6
6 215,9 161,9 203,2 190,5 --- 217,5 163,5 204,8
8 269,9 212,7 254 238,1 --- 271,5 214,3 255,6
10 323,8 266,7 304,8 285,8 --- 325,4 268,3 306,4
12 381 317,5 362 342,9 --- 382,6 319,1 363,5
14 412,8 349,2 393,7 374,6 --- 414,3 350,8 395,3
16 469,9 400 447,5 425,4 --- 471,5 401,6 449,3
18 533,4 450,8 511,2 489 --- 535 452,4 512,8
20 584,2 501,6 558,8 533,4 --- 585,8 503,2 560,4
24 692,2 603,2 666,8 641,4 --- 693,7 604,8 668,3
ASME B16.5
Dimensions of facings (other than ring joints, all pressure rating classes)

Minimum outside diameter of raised

Height
portion [notes 6, 7]

Inside diameter Large and small Depth of groove

Raised face Small female Large female Nominal pipe
of large and male and tongue or female
[notes 2,3] and groove, K and groove, L size (NPS)
small groove, Z [notes 2,4] [notes 1, 5]

23,8 --- --- --- 44 46 1/2

31,8 --- --- --- 52 54 3/4
36,5 --- --- --- 57 62 1
46 --- --- --- 67 75 1 1/4
52,4 --- --- --- 73 84 1 1/2
71,4 --- --- --- 92 103 2
84,1 --- --- --- 105 116 2 1/2
106,4 --- --- --- 127 138 3
119,1 --- --- --- 140 151 3 1/2
130,2 --- --- --- 157 168 4
158,8 --- --- --- 186 197 5
188,9 --- --- --- 216 227 6
236,5 --- --- --- 270 281 8
284,2 --- --- --- 324 335 10
341,3 --- --- --- 381 392 12
373,1 --- --- --- 413 424 14
423,9 --- --- --- 470 481 16
487,4 --- --- --- 533 544 18
531,8 --- --- --- 584 595 20
639,8 --- --- --- 692 703 24

The values, unless otherwise indicated, are to be considered in millimeters

Note 1: For small male and female joints, care should be taken in the use of these dimensions to ensure that the inside
diameter of the fitting or pipe is small enough to permit sufficient bearing surface to prevent the crushing of the
gasket. This applies particularly on lines where the joint is made on the end of the pipe. The inside diameter of the
fitting should match the inside diameter of the pipe as specified by the purchases. Threaded companion flanges
for small male and female joints are furnished with plain face and are threaded with American National Standard
Locknut Thread (NPSL).
Note 2: See para. 6.4.3 and Fig. 7 of ASME B 16.5 for thickness and outside diameters of laps.
Note 3: The height of the raised face is either 2 mm or 7 mm ( see para. 6.4.1).
Note 4: The height of the large and small male and tongue is 7 mm.
Note 5: The depth of the groove or female is 5 mm.
Note 6: The raised portion of the full face may be furnished unless otherwise specified on order.
Note 7: Large male and female faces and large tongue and groove are not applicable to Class 150 because of potential
dimensional conflicts.
ASME B16.5
Dimensions of ring-joint facings (all pressure rating classes)

23 deg

[Note (1)]

Approximate
distance
between flanges

Nominal pipe size (NPS)

Class 150 Class 300 Class 400 Class 600 Class 900 Class 1500 Class 2500 Groove number

--- 1/2 --- 1/2 --- --- --- R11

--- --- --- --- --- 1/2 --- 12
--- 3/4 --- 3/4 --- --- 1/2 13
--- --- --- --- --- 3/4 --- 14
1 --- --- --- --- --- --- 15
--- 1 --- 1 --- 1 3/4 16
1 1/4 --- --- --- --- --- --- 17
--- 1 1/4 --- 1 1/4 --- 1 1/4 1 18
1 1/2 --- --- --- --- --- --- 19
--- 1 1/2 --- 1 1/2 --- 1 1/2 --- 20
--- --- --- --- --- --- 1 1/4 21
2 --- --- --- --- --- --- 22
--- 2 --- 2 --- --- 1 1/2 23
--- --- --- --- --- 2 --- 24
2 1/2 --- --- --- --- --- --- 25
--- 2 1/2 --- 2 1/2 --- --- 2 26
--- --- --- --- --- 2 1/2 --- 27
--- --- --- --- --- --- 2 1/2 28
3 --- --- --- --- --- --- 29
--- [NOTE 2] --- [NOTE 2] --- --- --- 30
--- 3 [NOTE 2] --- 3 [NOTE 2] 3 --- --- 31
--- --- --- --- --- --- 3 32
3 1/2 --- --- --- --- --- --- 33
--- 3 1/2 --- 3 1/2 --- --- --- 34
--- --- --- --- --- 3 --- 35
4 --- --- --- --- --- --- 36
--- 4 4 4 4 --- --- 37
--- --- --- --- --- --- 4 38
--- --- --- --- --- 4 --- 39
5 --- --- --- --- --- --- 40
--- 5 5 5 5 --- --- 41
--- --- --- --- --- --- 5 42
6 --- --- --- --- --- --- 43
--- --- --- --- --- 5 --- 44
ASME B16.5
Dimensions of ring-joint facings (all pressure rating classes)

[Note (1)]

Groove dimensions Diameter of raised portion, K Approximate distance between flanges

Pitch Depth, Radius

Width, F Class 150 Class 300 400 600 Class 900 Class 1500 Class 2500 Class 150 Class 300 Class 400 Class 600 Class 900 Class 1500 Class 2500
diameter, P E [note 1] at bottom, r

34,14 5,54 7,14 0,8 --- 51 --- --- --- --- 3 --- 3 --- --- ---
39,67 6,35 8,74 0,8 --- --- --- 60,5 --- --- --- --- --- --- 4 ---
42,88 6,35 8,74 0,8 --- 63,5 --- --- 65 --- 4 --- 4 --- --- 4
44,45 6,35 8,74 0,8 --- --- --- 66,5 --- --- --- --- --- --- 4 ---
47,63 6,35 8,74 0,8 63,5 --- --- --- --- 4 --- --- --- --- --- ---
50,8 6,35 8,74 0,8 --- 70 --- 71,5 73 --- 4 --- 4 --- 4 4
57,15 6,35 8,74 0,8 73 --- --- --- --- 4 --- --- --- --- --- ---
60,33 6,35 8,74 0,8 --- 79,5 --- 81 82,5 --- 4 --- 4 --- 4 4
65,07 6,35 8,74 0,8 82,5 --- --- --- --- 4 --- --- --- --- --- ---
68,27 6,35 8,74 0,8 --- 90,5 --- 92 --- --- 4 --- 4 --- 4 ---
72,23 7,92 11,91 0,8 --- --- --- --- 102 --- --- --- --- --- --- 3
82,55 6,35 8,74 0,8 102 --- --- --- --- 4 --- --- --- --- --- ---
82,55 7,92 11,91 0,8 --- 108 --- --- 114 --- 6 --- 5 --- --- 3
95,25 7,92 11,91 0,8 --- --- --- 124 --- --- --- --- --- --- 3 ---
101,6 6,35 8,74 0,8 121 --- --- --- --- 4 --- --- --- --- --- ---
101,6 7,92 11,91 0,8 --- 127 --- --- 133 --- 6 --- 5 --- --- 3
107,95 7,92 11,91 0,8 --- --- --- 137 --- --- --- --- --- --- 3 ---
111,13 9,53 13,49 1,5 --- --- --- --- 149 --- --- --- --- --- --- 3
114,3 6,35 8,74 0,8 133 --- --- --- --- 4 --- --- --- --- --- ---
117,48 7,92 11,91 0,8 --- --- --- --- --- --- --- --- --- --- --- ---
123,83 7,92 11,91 0,8 --- 146 156 --- --- --- 6 --- 5 4 --- ---
127 9,53 13,49 1,5 --- --- --- --- 168 --- --- --- --- --- --- 3
131,78 6,35 8,74 0,8 154 --- --- --- --- 4 --- --- --- --- --- ---
131,78 7,92 11,91 0,8 --- 159 --- --- --- --- 6 --- 5 --- --- ---
136,53 7,92 11,91 0,8 --- --- --- 168 --- --- --- --- --- --- 3 ---
149,23 6,35 8,74 0,8 171 --- --- --- --- 4 --- --- --- --- --- ---
149,23 7,92 11,91 0,8 --- 175 181 --- --- --- 6 6 5 4 --- ---
157,18 11,13 16,66 1,5 --- --- --- --- 203 --- --- --- --- --- --- 4
161,93 7,92 11,91 0,8 --- --- --- 194 --- --- --- --- --- --- 3 ---
171,45 6,35 8,74 0,8 194 --- --- --- --- 4 --- --- --- --- --- ---
180,98 7,92 11,91 0,8 --- 210 216 --- --- --- 6 6 5 4 --- ---
190,5 12,7 19,84 1,5 --- --- --- --- 241 --- --- --- --- --- --- ---
193,68 6,35 8,74 0,8 219 --- --- --- --- 4 --- --- --- --- --- 4
193,68 7,92 11,91 0,8 --- --- --- 229 --- --- --- --- --- --- 3 ---
ASME B16.5
Dimensions of ring-joint facings (all pressure rating classes)

Nominal pipe size (NPS)

Class 150 Class 300 Class 400 Class 600 Class 900 Class 1500 Class 2500 Groove number

--- 6 6 6 6 --- --- 45

--- --- --- --- --- 6 --- 46
--- --- --- --- --- --- 6 47
8 --- --- --- --- --- --- 48
--- 8 8 8 8 --- --- 49
--- --- --- --- --- 8 --- 50
--- --- --- --- --- --- 8 51
10 --- --- --- --- --- --- 52
--- 10 10 10 10 --- --- 53
--- --- --- --- --- 10 --- 54
--- --- --- --- --- --- 10 55
12 --- --- --- --- --- --- 56
--- 12 12 12 12 --- --- 57
--- --- --- --- --- 12 --- 58
14 --- --- --- --- --- --- 59
--- --- --- --- --- --- 12 60
--- 14 14 14 --- --- --- 61
--- --- --- --- 14 --- --- 62
--- --- --- --- --- 14 --- 63
16 --- --- --- --- --- --- 64
--- 16 16 16 --- --- --- 65
--- --- --- --- 16 --- --- 66
--- --- --- --- --- 16 --- 67
18 --- --- --- --- --- --- 68
--- 18 18 18 --- --- --- 69
--- --- --- --- 18 --- --- 70
--- --- --- --- --- 18 --- 71
20 --- --- --- --- --- --- 72
--- 20 20 20 --- --- --- 73
--- --- --- --- 20 --- --- 74
--- --- --- --- --- 20 --- 75
24 --- --- --- --- --- --- 76
--- 24 24 24 --- --- --- 77
--- --- --- --- 24 --- --- 78
--- --- --- --- --- 24 --- 79
ASME B16.5
Dimensions of ring-joint facings (all pressure rating classes)

Groove dimensions Diameter of raised portion, K Approximate distance between flanges

Pitch Depth, Radius

Width, F Class 150 Class 300 400 600 Class 900 Class 1500 Class 2500 Class 150 Class 300 Class 400 Class 600 Class 900 Class 1500 Class 2500
diameter, P E [note 1] at bottom, r

211,12 7,92 11,91 0,8 --- 241 241 --- --- --- 6 6 5 4 --- ---
211,14 9,53 13,49 1,5 --- --- --- 248 --- --- --- --- --- --- 3 ---
228,6 12,7 19,84 1,5 --- --- --- --- 279 --- --- --- --- --- --- 4
247,65 6,35 8,74 0,8 273 --- --- --- --- 4 --- --- --- --- --- ---
269,88 7,92 11,91 0,8 --- 302 308 --- --- --- 6 6 5 4 --- ---
269,88 11,13 16,66 1,5 --- --- --- 318 --- --- --- --- --- --- 4 ---
279,4 14,27 23,01 1,5 --- --- --- --- 340 --- --- --- --- --- --- 5
304,8 6,35 8,74 0,8 330 --- --- --- --- 4 --- --- --- --- --- ---
323,85 7,92 11,91 0,8 --- 356 362 --- --- --- 6 6 5 4 --- ---
323,85 11,13 16,66 1,5 --- --- --- 371 --- --- --- --- --- --- 4 ---
342,9 17,48 30,18 2,4 --- --- --- --- 425 --- --- --- --- --- --- 6
381 6,35 8,74 0,8 406 --- --- --- --- 4 --- --- --- --- --- ---
381 7,92 11,91 0,8 --- 413 419 --- --- --- 6 6 5 4 --- ---
381 14,27 23,01 1,5 --- --- --- 438 --- --- --- --- --- --- 5 ---
396,88 6,35 8,74 0,8 425 --- --- --- --- 3 --- --- --- --- --- ---
406,4 17,48 33,32 2,4 --- --- --- --- 495 --- --- --- --- --- --- 8
419,1 7,92 11,91 0,8 --- 457 --- --- --- --- 6 6 5 --- --- ---
419,1 11,13 16,66 1,5 --- --- 467 --- --- --- --- --- --- 4 --- ---
419,1 15,88 26,97 2,4 --- --- --- 489 --- --- --- --- --- --- 6 ---
454,03 6,35 8,74 0,8 483 --- --- --- --- 3 --- --- --- --- --- ---
469,9 7,92 11,91 0,8 --- 508 --- --- --- --- 6 6 5 --- --- ---
469,9 11,13 16,66 1,5 --- --- 524 --- --- --- --- --- --- 4 --- ---
469,9 17,48 30,18 2,4 --- --- --- 546 --- --- --- --- --- --- 8 ---
517,53 6,35 8,74 0,8 546 --- --- --- --- 3 --- --- --- --- --- ---
533,4 7,92 11,91 0,8 --- 575 --- --- --- --- 6 6 5 --- --- ---
533,4 12,7 19,84 1,5 --- --- 594 --- --- --- --- --- --- 5 --- ---
533,4 17,48 30,18 2,4 --- --- --- 613 --- --- --- --- --- --- 8 ---
558,8 6,35 8,74 0,8 597 --- --- --- --- 3 --- --- --- --- --- ---
584,2 9,53 13,49 1,5 --- 635 --- --- --- --- 6 6 5 --- --- ---
584,2 12,7 19,84 1,5 --- --- 648 --- --- --- --- --- --- 5 --- ---
584,2 17,48 33,32 2,4 --- --- --- 673 --- --- --- --- --- --- 10 ---
673,1 6,35 8,74 0,8 711 --- --- --- --- 3 --- --- --- --- --- ---
692,15 11,13 16,66 1,5 --- 749 --- --- --- --- 6 6 6 --- --- ---
692,15 15,88 26,97 2,4 --- --- 772 --- --- --- --- --- --- 6 --- ---
692,15 20,62 36,53 2,4 --- --- --- 794 --- --- --- --- --- --- 11 ---

The values, unless otherwise indicated, are to be considered in millimeters

Note 1: The height of the raised portion is equal to the depth of the groove dimension, E, but is not subjected to the tolerances for E. Former full-face contour may be used.
Note 2: For ring joints with lapped flanges in Classes 300 and 600, ring and groove number R30 is used instead of R31.
Tolerances: E (depth) +0,04 /-0,0
F (width) ±0,2
P (pitch diameter) ±0,13
R (radius at bottom)
R ≤ 2 +0,8 / -0,0
R > 2 ±0,8
23 deg (angle) ± 1/2 deg
The data reported in this catalogue are for reference purpose only
T.A.L. Group reserves the right to modify without notice the information here contained
The technical department is at your disposal for any further technical and regulatory clarification.