Product model Address Coding rule 01（Read Coil Status）

03（Read Holding Registers）

Changzhou Winpark Electronics Co., Ltd TPC-8C2─□ □ □ □ □ –SP□ □-V□ □ The address select switch use 8421 coding. 1 corresponds to 8; 2 corresponds to 4; 3
Supported command 05（Force Single Coil）
Address: 6th Floor of Tianan Industrial Village ⑴ ⑵ ⑶⑷⑸⑹ ⑺⑻ ⑼⑽ corresponds to 2; 4 corresponds to 1; When it is switched to ON, it means valid. The
06（Preset Single Register）
SN Name Explanation communication address is the sum of the valid numbers added a extra 20. For
A plus, Xinbei, Changzhou 213022, China example: （1：ON,2：OFF,3：ON,4：OFF）,（8+0+2+0）+20=30; Which means the
16（Preset Multiple Regs）
(1) Design code 8C2: 8C2series products
Tel: 0086-519-85132277 Email: [email protected] Alternating control area with
module address is 30. If there are several modules connected in the same BUS, the Address：80，words: 2-8
(2) Input method 0: thermocouple input touch screen
Fax: 0086-519-85108252 Web: www.cnwinpark.com address of modules should be different from each other.
Alternating status area with
(3) output method 0: break output Address：88
touch screen
8-Channel Temperature Control Module (4) Alarm method 0: upper limit upward alarm ：
Baud rate： Because the communication buffer area is relatively small in the module, please close
Operation Manual SW1,SW2 switch OFF,OFF OFF,ON ON,OFF ON,ON communication optimization function when programming touch screen configuration.
（苏）制 04000201 (5) Input type 0: K 1:E 4:Pt100 5:J status
Baud rate (BPS) 9600 19200 38400 57600
Basic data description
Version No.:V2.05 0: relay contacts output Version No. address of module software：W8600
1: nonisolated logic level output (to Paramet Explanation Read/w Addres Unit
(6) Output type control SSR)
 Parameter explanation
Thank you for using Winpark products. Please read this manual carefully before er rite s
2: Isolated logic level output (to Proportional Band: Proportional band of heat end ( when P=0, it is
operating the controller and always keep it around you to make it available easily P PV1 Channel 1 PV value R W48 0.1℃
control SSR) stepping control)
anytime. PV2 Channel 2 PV value R W49 0.1℃
I Integral Time: Integral Time of heating end ( Re-adjust time) PV3 Channel 3 PV value R W50 0.1℃
(7) (8) Special model code. **: Ordinary 2：K (0 ~1000° C)
Differential Time: Differential time of heating end (advance adjust time). PV4 Channel 4 PV value R W51 0.1℃
D
(9) (10) Software Version 01: Ordinary (“D” is return difference in stepping control) PV5 Channel 5 PV value R W52 0.1℃
WARNING Overshoot suppression: The smaller is this parameter, the smaller is the PV6 Channel 6 PV value R W53 0.1℃
IT
first overshoot, but it will take longer to reach the set temperature. PV7 Channel 7 PV value R W54 0.1℃
MTC-8C-EX1-□ proportional band separation: To prevent overshoot caused by Channel 8 PV value R
Wire connection PV8 W55 0.1℃
（1） ⑵ ⑶ SP
proportional function.
If failure or error of this instrument could result in a critical accident of the SV1 Channel 1 SV value R/W W40 1℃
No. Name Explanation T Heat cycle time: Output one action in this cycle under break control
system, install an external protection circuit to prevent such an accident. SV2 Channel 2 SV value R/W W41 1℃
Choose fuse protection power supply wire and output wire to avoid strong ⑴ Design code 8C: 8C series product Refrigerating Proportional band: Proportional band of time proportional
PC SV3 Channel 3 SV value R/W W42 1℃
current strike which may cause failure or damage to the controller. ⑵ Mark EX1：expansion module control in refrigerating end SV4 Channel 4 SV value R/W W43 1℃
0：relay contact switch output Refrigerating Proportion band offset: Proportional band offset of time
Power supply ⑶ Output type SV5 Channel 5 SV value R/W W44 1℃
1：logic electrical level output (control SSR) PO
Please use the controller under rated power supply to avoid causing failure proportional control in refrigerating end SV6 Channel 6 SV value R/W W45 1℃
or damage to the controller. Refrigerating cycle time: Output one action in this cycle under break SV7 Channel 7 SV value R/W W46 1℃
CT
Don’t turn on thee power supply until all of the wiring is completed and Installation instruction control SV8 Channel 8 SV value R/W W47 1℃
checked again Temperature modification: Modify temperature when the position of
TPC-8C2 MTC8C-EX1 TR
Using sites limitation sensor or other factors affect measuring. ：STATUS（
Remark 1： （output status word））bit explanation
Actual size：145*90*72 Actual size：96*90*38
Don’t use this controller in the places subject to flammable or explosive gas Dead band control Channel output status corresponding to bit
to avoid cause fire. （picture is only for reference, please refer to actual size）
（Unit：㎜） DB Insensitive area of alarm. It can reduce the action times of alarm relay.
Don’t use this controller in dusty, corrosive and steam exhaust environment Bit 7 6 5 4 3 2 1 0
Range ; -10.0%~10.0%（Default 0.0%）
Don’t use this controller where there are strong shock and strike. High 8 CH8 CH7 CH6 CH5 CH4 CH3 CH2 CH1
Input filter factor
FIL used for input signal filter factor. The bigger is this factor the smoother is bit heat heat heat heat heat heat heat heat
the input. But it cause delay to the input. Press SET to enter next page.
Coil
B247 B246 B245 B244 B243 B242 B241 B240
General Electrical Data address
Refrigerating Parameter Description
Rated voltage 85V AC~265V AC PC: Refrigerating Proportional band; PO: Refrigerating offset (Unit: ° C); CT: Low 8 CH8 CH7 CH6 CH5 CH4 CH3 CH2 CH1
Refrigerating cycle time (Unit: Second)
Power consumption ≤5VA Installation slot
bit cool cool cool cool cool cool cool cool
Two types of refrigerating:
Power supply- input：1500V AC 1min 34.5 1. Step refrigerating Coil
Insulation Strength Input-relay output：1500V AC 1min PC=0，PO：Refrigerating offset， CT：Non-defined B255 B254 B253 B252 B251 B250 B249 B248
1

address
Power supply-relay output：1500V AC 1min For example: set SV=100, PO=10, when PV=110.5° C alarm outputs, when
7

Input-relay output：>20MΩ PV=109.5° C alarm stops. When PV=109.6° C ~110.4° C, it remains the original
status: which means Return Difference Value=1° C Remark 2：SWITCH（ （work switch））bit explanation
Insulation Resistance Input-power supply：>20MΩ Whether the channel corresponding to bit is controlling
Power supply-relay output：>20MΩ 2. Proportional refrigerating
PC= Proportional Band （%）， PO: Refrigerating offset (Unit: ° C), CT: temperature
Working Ambient temperature：0° C ~50° C Wire Connection Refrigerating cycle time (Unit: Second) Bit 7 6 5 4 3 2 1 0
Environment Relative humidity：35%~85%（no condensation） TPC-8C2 MTC8C-EX1 Refrigerating output = （actual temperature –set temperature- Refrigerating
（cooling output module）
） 16 CH8 CH7 CH6 CH5 CH4 CH3 CH2 CH1
offset）/（ （Proportion band %）*500）
High switch switch switch switch switch switch switch switch
For example: PC=5，PO=5，CT=30，SV=100，Actual temperature =108
AC85-265V

Measuring Data Refrigerating output =（108-100-5）/（5%*500）=0.12

8 bit
Coil
Permissible input resistance thermocouple：≤ 100Ω Because Refrigerating cycle time CT=30 seconds，in refrigerating cycle the valid B263 B262 B261 B260 B259 B258 B257 B256
C F
output time=30*0.12=3.6seconds address
8421 S S Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8
O
M G N L
W W 扩展口
地址 1 2 Low 8
Measuring range 0 ~600° C or 0 ~1000° C COM CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8
输出公共端

bit
Display accuracy 0.1° C Basic communication protocol： Modicon Modbus Protocol，RTU
Slave Mode
tolerance ±0.5%FS
(Note: If the touch screen has the function of fragment communication
电源指示灯
optimization, please close this optimization function)
Address Assignment of system parameter
RS485 输出端子指示灯 Communication Name Address Explanation
 Output data +- T1+T1-T2+T2-T3+T3-T4+T4-T5+T5-T6+T6-T7+T7-T8+T8-
RS485 Data bit 8
CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 POW 扩展口 connection
Capacity of relay output 3A 220V；
CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 Parity bit even Stop bit 1 IN_TYPE Input type W164 0：K，1：E，5：J
contacts Resistive load or designated
SCR Zero cross trigger Baud rate 9600BPS-57600BPS
100mA ：
Remark： OUT_TYPE Output type W165 See appended Instructions
signal
Output voltage: 12V±3V 1）nonisolated logic level output: the COM terminal of main module is 12V and Equipment address 20+ the value of address coding switch
SSR Trigger signal connect to the anode of SSR; Q1~Q8 connect to the cathode of SSR;
Output current：35mA Exist in form of holding register（HR）, show in 2 PRECISION Display accuracy B296 See appended Instructions
2）isolated logic level output: the COM terminal of main module connect 24V Parameter, variable bytes 16 hexadecimal complement, address shows
input(Anode), Q1~Q8 connect to the anode of SSR; the cathode of SSR connect to as Wxxxx
earth terminal of 24V power supply.
Control switch, bit status Exist in form of coil, show in 1 bit, value 1 means
3）The above mentioned two ways can’t be mixed, otherwise there might be damage
valid., address shows as Bxxxx
to module.
1 2 3 4
 Address Assignment of control parameter per channel 2 Measuring radix point control Channel 3 manual output W058 0~100.0 10.2 Word parameter
CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 Function Address control value Function Address
P W100 W200 W300 W400 W500 W600 W700 W800 Channel 4 manual output W059 0~100.0
Measuring value When the bit=0，the unit of PV output value is 1℃ control value Range 0~100 correspond to 0%~100% power,
I W101 W201 W301 W401 W501 W601 W701 W801 B296
radix point control When the bit=1，the unit of PV output value is0. 1℃ Channel5 manual output W060 0~100.0 Power when power restriction is enabled and the actual
D W102 W202 W302 W402 W502 W602 W702 W802
control value restriction W022 temperature is below the power restriction
IT W103 W203 W303 W403 W503 W603 W703 W803
3 Output mode Channel 6 manual output W061 0~100.0 value temperature, to restrict the max output power
SP W104 W204 W304 W404 W504 W604 W704 W804 control value lower than this power.
3.1 （W165）
Address（ ）
T W105 W205 W305 W405 W505 W605 W705 W805 Bit 7 6 5 4 3 2 1 0 Channel 7 manual output W062 0~100.0 Power 0~400 correspond to 0~400℃，when temperature
PC W106 W206 W306 W406 W506 W606 W706 W806 control value restriction W023 exceeds this number, power restriction function is
expansion module output main module output
Channel 8 manual output W063 0~100.0 temperature canceled.
PO W107 W207 W307 W407 W507 W607 W707 W807 Output 0000：refrigerating output 0000：relay or SSR output
control value
CT W108 W208 W308 W408 W508 W608 W708 W808 mode 0001：User-defined output, the low 8 0001：SCR controlled AC cycle
byte content of address (W096) register proportional output
11 Full switch on/off function
TR W132 W232 W332 W432 W532 W632 W732 W832 6.3 Remark： ： Channel manual output control value: user 11.1 Bit paramete
content is the output of expansion relay.
DB W133 W233 W333 W433 W533 W633 W733 W833 defines output value under manual status（ （ 0~100.0）
）; Function Address
“1” means relay pickup
FIL W134 W234 W334 W434 W534 W634 W734 W834 display output value calculated by PID under automatic All B184 This bit=1, all temperature control channels are
mode（ （0~100.0）） temperature on, this bit reset automatically.
4 bit address of direct logic point output
control on
Appended Instructions： 4.1 bit parameter
6.4 When break coupling mark is showed, manual output is All B185 This bit=1, all temperature control channels are
CH8 CH7 CH6 CH5 CH4 CH3 CH2 CH1 forbidden and no heating output.
1 High/low temperature alarm temperature off, this bit reset automatically.
W096 control off
1.1 Bit parameter Corresponding bit address（B）
（lowbyte） 7 Auto-tuning mark
Enable high/low “1” means 1551 1550 1549 1548 1547 1546 1545 1544
CH8 CH7 CH6 CH5 CH4 CH3 CH2 CH1 7.1 Bit parameter 12 ，-10.0~10.0 correspond to -10.0%~10.0%
Dead band control，
temperature alarm relay pickup
W017 Correspond bit address（B） CH8 CH7 CH6 CH5 CH4 CH3 CH2 CH1 ）
（default 0.0%）
12.1 Word parameter
（highbyte）Enable high 279 278 277 276 275 274 273 272 5 Sensor abnormal protection W013（highbyte） Corresponding bit address（B）
temperature alarm: Enable Auto-tuning mark 215 214 213 212 211 210 209 208
Function Address
5.1 Judging by heating power and temperature rising time When this value is positive, there is dead band in
high temperature alarm of 5.1.1 temperature rise threshold value 3.0 degree (fixed) (1 means
the corresponding corresponding 2-way output, which means the actual output=0,
5.1.2 setting parameter when the absolute value of calculated output
channel, when the value is 5.1.3 bit parameter channel is under
set to 1, it means the auto-tuning status, CH1 dead value is smaller than this value; when this value
W010 CH8 CH7 CH6 CH5 CH4 CH3 CH2 CH1 W133
function is enabled. could be set.) band control is negative, there is overlapping with 2-way
Corresponding bit address（B） output, the actual output value equals to sum of
（lowbyte）Enable low 287 286 285 284 283 282 281 280 Alarm status 167 166 165 164 163 162 161 160 this value and the absolute value of calculated
temperature alarm: Enable
Alarm clear: set to 1 to 175 174 173 172 171 170 169 168
8 Break coupling mark
output value
low temperature alarm of
clear corresponding
8.1 Bit parameter
CH2 dead W233
the corresponding CH8 CH7 CH6 CH5 CH4 CH3 CH2 CH1
alarm output, control band control
channel, when the value is W013（lowbyte） Corresponding bit address（B）
bit resets to zero CH3 dead W333
set to 1, it means the Break coupling 223 222 221 220 219 218 217 216
automatically. band control
function is enabled. mark
CH4 dead W433
5.1.4 Word parameter （1 means
band control
high/low temperature alarm corresponding
CH8 CH7 CH6 CH5 CH4 CH3 CH2 CH1 Function Address CH5 dead W533
output channel is under
Heating power W020 0~1000 correspond with 0~100.0% band control
W014 Correspond bit address（B） valve value Break coupling
（ highbyte ） high 231 230 229 228 227 226 225 224 CH6 dead W633
status）
Temperature rise W021 0~3600 correspond with 0~3600 seconds, if set band control
temperature alarm output:
valve value to 0, the alarm function is invalid. CH7 dead W733
When the value is 1, it 9 2-way PID Paramete
means the corresponding band control
5.2 Working theory 9.1 Bit parameter CH8 dead W833
channel is in high
5.2.1 When the heating power is continuously bigger CH8 CH7 CH6 CH5 CH4 CH3 CH2 CH1
band control
temperature alarm state.
than threshold value and temperature rise doesn’t W024（lowbyte） Corresponding bit address（B）
（ lowbyte ） low 239 238 237 236 235 234 233 232
reach 3.0 degree in temperature rise threshold 2-way PID 399 398 397 396 395 394 393 392 External wiring instructions
temperature alarm output:
value time, alarm is output. control (1
When the value is 1, it
means 2-way 1. communication cable wiring instructions:
means the corresponding a) Communication cable should be shielded or twisted-pair cable.
6 Manual / Auto switch PID is enabled in
channel is in low Loose wires are forbidden
6.1 Bit parameter corresponding
temperature alarm state. b) Communication cable and power cable should be laid
W012 CH8 CH7 CH6 CH5 CH4 CH3 CH2 CH1 channel）
Machine high temperature when there are 2 or more channels of high separately.
B176 Corresponding bit address（B） 9.2 Word parameter
alarm bit temperature alarm, the bit=1
Automatic reset control: set 199 198 197 196 195 194 193 192 Function Address 2. thermocouple wiring instructions
Machine low temperature when there are 2 or more channels of low
B177 to 1, in the next action cycle, a) Compensation wire should be used to connect thermocouple
alarm bit temperature alarm, the bit=1
the program will 2-way PID W025 Range 0~100 correspond to 0.1~10.0, when the and module input port. Or use shielded or twisted-pair wire
Machine high temperature when this bit=1, the eighth channel of
automatically clear enabled refrigerating set data <1.0, it means lower refrigerating output at least, but this would cause temperature difference in
alarm expansion module B288 expansion module is forced to be used as measuring.
bits of itself and manual. power output power; when the set data>1.0, it means higher
output enable Machine high temperature alarm b) The connection wire for 8 channels of thermocouple should be
The channel would enter to factor refrigerating output power
Machine low temperature when this bit=1, the seventh channel of auto control status steadily laid concentratedly to enhance the stability of temperature
alarm expansion module B289 expansion module is forced to be used as then.
measuring.
output enable Machine low temperature alarm
10 Power restriction c) Thermocouple wiring should be laid separately from the power
Manual enable control: set to 207 206 205 204 203 202 201 200 10.1 Bit parameter line
1, the corresponding channel CH8 CH7 CH6 CH5 CH4 CH3 CH2 CH1
1.2 Word parameter enter to manual status; set to W024 3. Solid state output wiring instructions
Function Address 0 to enter to auto status. All Corresponding bit address（B） a) The common port of solid state output can’t be connected to
（highbyte）
Unit: ℃，if high temperature alarm of this channel is channels are in auto status the common port of other modules or circuits.
high Power 391 390 389 388 387 386 385 384
temperature
enabled, when(PV-SV) ≥Value of high temperature when power on. b) The control line of solid state output could only be connected
restriction
W026 alarm deviation, the high temperature alarm of this with corresponding SSR.
alarm control (1
channel output=1. if high temperature alarm 6.2 Word parameter c) Solid state 8output line should be laid concentratedly and
deviation means Power separated from the power line.
deviation=0, it means high temperature alarm is invalid. Function Address restriction is
W027 Unit: ℃，if low temperature alarm of this channel is
low Channel 1 manual output W056 0~100.0 enabled in
enabled, when(PV-SV) ≥Value of low temperature
temperature control value corresponding
alarm deviation, the low temperature alarm of this
alarm Channel 2 manual output W057 0~100.0 channel）
channel output=1. if low temperature alarm
deviation control value
deviation=0, it means low temperature alarm is invalid.
7 8
5 6