High Durability Series

Longer Life Cylinder RoHS

New technology offers at least

4 times better durability
4 times
or more ¡The maintenance intervals
will be extended
Durability (Life)

Longer life Existing model

(Air cylinder: CM2 series)
cylinder ∗ B
 ased on SMC’s specific
testing conditions

¡Employs the same specification and High Durability Series

dimensions as the existing models,

High Durability Series is the series
name for the “special specification” that
offers superior durability and
CM2 Air Cylinder series environmental resistance compared to
standard products.

Series Variations
Bore size
Series Action Model Cushion Standard stroke
20 25 32 40
Air cylinder
CM2 series
Double acting,
Single rod
CM2-XB24 V V V V Rubber bumper 25 to 300

CM2-XB24
CAT.ES20-286A
 High Durability Series

Longer Life Cylinder: Double Acting, Single Rod

CM2-XB24
ø20, ø25, ø32, ø40
How to Order

CM2 B 40 150 Z1 XB24

With auto switch CDM2 B 40 150 Z1 M9BW XB24
With auto switch
(Built-in magnet)
q w e r t y u i o
Longer life cylinder

q Mounting w Bore size e Port thread type r Cylinder stroke [mm] t Rod end thread
B Basic (Double-side bossed) 20 20 mm Nil Rc Refer to page 2 for standard strokes. Nil Male rod end
L Axial foot bracket 25 25 mm TN NPT F Female rod end
F Rod flange 32 32 mm TF G
G Head flange 40 40 mm
C Single clevis
D Double clevis y Pivot bracket u Rod end bracket i Auto switch
U Rod trunnion Nil No bracket Nil No bracket W Double knuckle joint Without auto
T Head trunnion Nil switch
N Pivot bracket V Single knuckle joint Q Rod end
E Integrated clevis
* O
 nly for “C”, “T”, “U”, “E”, “V”, and * No bracket is provided with the female rod end. * For applicable auto
V Integrated clevis (90°) “UZ” mounting types * A knuckle joint pin is not provided with the single knuckle switches, refer to the
BZ Boss-cut/Basic * T
 he pivot bracket is shipped together with joint. table below.
FZ Boss-cut/Rod flange the product but does not come assembled. * The rod end bracket is shipped together with the product
UZ Boss-cut/Rod trunnion but does not come assembled.
o Number of auto switches
Nil 2
S 1
n n * Refer to page 2 for the ordering example of cylinder assembly.

Applicable Auto Switches/Refer to the Web Catalog for further information on auto switches.
Load voltage Auto switch model Lead wire length [m]
Indicator light

Electrical Wiring Pre-wired

Type Special function 0.5 1 3 5 None Applicable load
entry (Output) DC AC Perpendicular In-line connector
(Nil) (M) (L) (Z) (N)
3-wire (NPN) M9NV M9N V V V v — v
5 V, 12 V IC circuit
Grommet 3-wire (PNP) M9PV M9P V V V v — v
M9BV M9B V V V v — v
Solid state auto switch

—— 2-wire 12 V —
Connector — H7C V — V V V —
Terminal 3-wire (NPN) 5 V, 12 V — G39A — — — — V — IC circuit
conduit 2-wire 12 V — K39A — — — — V — —
Relay,
Yes

3-wire (NPN) 24 V — M9NWV M9NW V V V v — v

Diagnostic indication 5 V, 12 V IC circuit PLC
(2-color indicator)
3-wire (PNP) M9PWV M9PW V V V v — v
2-wire 12 V M9BWV M9BW V V V v — v —
Grommet 3-wire (NPN) M9NAV*1 M9NA*1 v v V v — v
Water resistant 5 V, 12 V IC circuit
(2-color indicator)
3-wire (PNP) M9PAV*1 M9PA*1 v v V v — v
2-wire 12 V M9BAV*1 M9BA*1 v v V v — v —
With diagnostic output (2-color indicator) 4-wire (NPN) 5 V, 12 V — H7NF V — V v — v IC circuit
3-wire
— 5V — A96V A96 V V V V — v IC circuit —
Yes

(NPN equivalent)
A93V A93 V V V V — v*2
100 V —
Grommet
V V V V — v*2 IC circuit
Reed auto switch

A90V A90 100 V or less

No Yes No Yes No

— B54 100 V, 200 V

V — V V — — Relay,
—— — B64 200 V or less
V — V — — — — PLC
12 V — C73C V — V V V— —
Connector 2-wire 24 V
— C80C 24 V or less
V — V V V — IC circuit
Terminal — A33A — — — — V — — PLC
conduit — A34A — — — — V —
Yes

100 V, 200 V — Relay,

DIN terminal — A44A — — — — V —
PLC
Diagnostic indication (2-color indicator) Grommet — — — B59W V — V — — —
∗1 Water-resistant type auto switches can be mounted on the above models, but SMC cannot guarantee water resistance.
A water-resistant type cylinder is recommended for use in an environment which requires water resistance.
∗2 The load voltage used is 24 VDC.
* Lead wire length symbols: 0.5 m ·······Nil (Example) M9NW ∗ Auto switches marked with a “v” are produced upon receipt of order.
1 m ······· M (Example) M9NWM ∗ D
 o not indicate suffix “N” for no lead wire on the D-A3A/A44A/G39A/K39A models.
3 m ······· L (Example) M9NWL
5 m ······· Z (Example) M9NWZ
None ······· N (Example) H7CN
* Since there are applicable auto switches other than those listed above, refer to the Web Catalog for details.
* For details on auto switches with pre-wired connectors, refer to the Web Catalog.
* The D-A9mm/M9mmm auto switches are shipped together with the product but do not come assembled. (Only the auto switch mounting brackets are assembled before shipment.)
A 1
 High Durability Series

Longer Life Cylinder: Double Acting, Single Rod CM2-XB24

Specifications

Bore size [mm] 20 25 32 40

Type Pneumatic
Action Double acting, Single rod
Fluid Air
Proof pressure 1.5 MPa
Max. operating pressure 1.0 MPa
Min. operating pressure 0.05 MPa
Without auto switch: −10°C to 70°C
Ambient and fluid temperatures (No freezing)
With auto switch: −10°C to 60°C
Lubrication Not required (Non-lube)
Symbol
Stroke length tolerance*1
+1.4
0 mm
Double acting, Single rod Piston speed 50 to 750 mm/s
Cushion Rubber bumper
Allowable Rubber Male thread 0.27 J 0.4 J 0.65 J 1.2 J
kinetic energy bumper Female thread 0.11 J 0.18 J 0.29 J 0.52 J
*1 Does not include the amount of bumper change
* Operate the cylinder within the allowable kinetic energy.
The mounting pitch and shape of this product * For the allowable rod end lateral load, refer to the “Air Cylinders Model Selection” in the Web
Catalog.
with auto switch are the same as those of the
CM2 series with auto switch.
For details, refer to the Web Catalog.
• Auto Switch Proper Mounting Position Standard Strokes
(Detection at stroke end) and Mounting
Height
• Min. Stroke for Auto Switch Mounting Bore size Max. manufacturable
Standard stroke [mm]*1
• Operating Range [mm] stroke [mm]
• Auto Switch Mounting Brackets/Part Nos. 20
25
25, 50, 75, 100, 125, 150, 200, 250, 300 1000
32
40
*1 Intermediate strokes not listed above are produced upon receipt of order. The manufacturing
of intermediate strokes in 1 mm increments is possible. (Spacers are not used.)
* Applicable strokes should be confirmed according to the usage. For details, refer to the “Air
Cylinders Model Selection” in the Web Catalog. In addition, the products that exceed the
standard stroke might not be able to fulfill the specifications due to deflection, etc.

Option: Ordering Example of Cylinder Assembly

Cylinder model: CDM2C20-50Z1-NV-M9BW-XB24

Single clevis
Mounting C: Single clevis
Pivot bracket N: Yes
Rod end bracket V: Single knuckle joint
Single knuckle joint Auto switch D-M9BW: 2 pcs.

* P
 ivot bracket, single knuckle joint and auto
switch are shipped together with the product
but do not come assembled.

Precautions Pivot bracket * P

 ivot bracket is only available for “C”, “T”,
“U”, “E”, “V”, and “UZ” mounting types.
* No bracket is provided with the female rod
Refer to page 13 before handling the Auto switch
end.
products.

The allowable kinetic energy, allowable loads at the rod end, theoretical output, and weight
are equivalent to those of the Air Cylinder CM2 series. For details, refer to the Web Catalog.

2
 High Durability Series

CM2-XB24

Mounting and Accessories

Accessories Standard (mounted to the body) Standard (shipped together but does not come assembled) Option

Clevis pivot *5
(CM2E/CM2V)

(CM2E/CM2V)
*1

*7

*5

*5

*6
Single knuckle joint

Double knuckle joint

(For trunnion)
Foot bracket

Mounting nut
(Male thread)
Mounting nut

Rod end nut

bracket pin

(Male thread only)

Rod end
(Male thread only)
Clevis pivot

bracket pin
Mounting

clevis pin

Trunnion
bracket
Double

Double
Flange

bracket
Single
clevis

clevis
Body

Liner

Pivot

Pivot
nut
Mounting
B Basic (Double-side bossed) V(1 pc.) V(1 pc.) V(1 pc.) — — — — — — — — — — — — — V V V
L Axial foot bracket V(1 pc.) V(1 pc.)*2 V(1 pc.) — — — V(1 pc.)*2 V(2 pcs.) — — — — — — — — V V V
F Rod flange V(1 pc.) V(1 pc.) V(1 pc.) — — — — — V(1 pc.) — — — — — — — V V V
G Head flange V(1 pc.) V(1 pc.) V(1 pc.) — — — — — V(1 pc.) — — — — — — — V V V
C Single clevis V(1 pc.) — *3 V(1 pc.) V(1 pc.) — V(Max. 3 pcs.) — *3 — — — — — — — — — V V V
D Double clevis V(1 pc.) — *3 V(1 pc.) — V(1 pc.) V(Max. 3 pcs.) — *3 — — — — V(1 pc.) — — — — V V V
U Rod trunnion V(1 pc.) — *4 V(1 pc.) — — — — — — — — — V(1 pc.) V(1 pc.) — — V V V
T Head trunnion V(1 pc.) — *4 V(1 pc.) — — — — — — — — — V(1 pc.) V(1 pc.) — — V V V
E Integrated clevis V(1 pc.) — *3 V(1 pc.) — — — — *3 — — — — — — — — — V V V
V Integrated clevis (90°) V(1 pc.) — *3 V(1 pc.) — — — — *3 — — — — — — — — — V V V
BZ Boss-cut/Basic V(1 pc.) V(1 pc.) V(1 pc.) — — — — — — — — — — — — — V V V
Boss-cut/
FZ Rod flange V(1 pc.) V(1 pc.) V(1 pc.) — — — — — V(1 pc.) — — — — — — — V V V

Boss-cut/
UZ Rod trunnion V(1 pc.) — *4 V(1 pc.) — — — — — — — — — V(1 pc.) V(1 pc.) — — V V V

Standard (mounted to the body) Option

Mounting: C
Pivot bracket symbol: N V
V(1 pc.) — *3 V(1 pc.) V(1 pc.) — — *3 — — V(2 pcs.) V(1 pc.) — — — — — V V V
(Max. 3 pcs.)
Single clevis + Pivot bracket + Pin
Mounting: T, U, UZ
Pivot bracket symbol: N V(1 pc.) — *4 V(1 pc.) — — — — *3 — — V(2 pcs.) — — V(1 pc.) V(1 pc.) — — V V V
Trunnion + Pivot bracket
Mounting: E
Pivot bracket symbol: N V(1 pc.) — *3 V(1 pc.) — — — — *3 — — — — — — — V(1 pc.) V(1 pc.) V V V
Integrated clevis + Pivot bracket + Pin
Mounting: V
Pivot bracket symbol: N V(1 pc.) — *3 V(1 pc.) — — — — *3 — — — — — — — V(1 pc.) V(1 pc.) V V V
Integrated clevis (90°) + Pivot bracket + Pin
*1 A rod end nut is not provided with the female rod end. *6 A pin and retaining rings (split pins for ø40) are included.
*2 Two mounting nuts are included. *7 This is the part(s) used to adjust the clevis angle. Mounting quantity can vary.
*3 A mounting nut is not included with the clevis. * Stainless steel mounting brackets and accessories are also available.
*4 A
 trunnion nut is included with “T”, “U”, and “UZ” mounting types. Refer to the Web Catalog for details.
*5 Retaining rings are included.

Mounting Brackets/Part Nos.

Min. Bore size [mm]
Mounting bracket order Contents (for Min. order quantity)
quantity 20 25 32 40
Foot bracket*1 2 CM-L020B CM-L032B CM-L040B 2 foot brackets, 1 mounting nut
Foot bracket*2 1 CMZ1-L020B CMZ1-L032B CMZ1-L040B 1 foot bracket
Flange 1 CM-F020B CM-F032B CM-F040B 1 flange
Single clevis*3 1 CM-C020B CM-C032B CM-C040B 1 single clevis, 3 liners
1 double clevis, 3 liners,
Double clevis (with pin)*3, *4 1 CM-D020B CM-D032B CM-D040B
1 clevis pin, 2 retaining rings
Double clevis pin 1 CDP-1 CDP-2 1 clevis pin, 2 retaining rings (split pins)
Trunnion (with nut) 1 CM-T020B CM-T032B CM-T040B 1 trunnion, 1 trunnion nut
Rod end nut 1 NT-02 NT-03 NT-04 1 rod end nut
Mounting nut 1 SN-020B SN-032B SN-040B 1 mounting nut
Trunnion nut 1 TN-020B TN-032B TN-040B 1 trunnion nut
Single knuckle joint 1 I-020B I-032B I-040B 1 single knuckle joint
1 double knuckle joint,
Double knuckle joint 1 Y-020B Y-032B Y-040B
1 knuckle pin, 2 retaining rings
Rod end 1 KJ8D KJ10D KJ14D 1 rod end
Double knuckle joint pin 1 CDP-1 CDP-3 1 knuckle pin, 2 retaining rings (split pins)
Clevis pivot bracket pin (For CM2E/CM2V) 1 CD-S02 CD-S03 1 clevis pin, 2 retaining rings
Clevis pivot bracket (For CM2E/CM2V) 1 CM-E020B CM-E032B 1 clevis pivot bracket, 1 clevis pin, 2 retaining rings
Pivot bracket (For CM2C) 1 CM-B032 CM-B040 2 pivot brackets (1 of each type)
Pivot bracket pin (For CM2C) 1 CDP-1 CD-S03 1 pin, 2 retaining rings
Pivot bracket (For CM2T/CM2U) 1 CM-B020 CM-B032 CM-B040 2 pivot brackets (1 of each type)
*1 Order two foot brackets per cylinder. For dimensions of accessories (options),
*2 A single foot bracket is available. refer to the Web Catalog.
*3 3 liners are included with a clevis bracket for adjusting the mounting angle.
*4 A clevis pin and retaining rings (split pins for ø40) are included.
3
 High Durability Series

Longer Life Cylinder: Double Acting, Single Rod CM2-XB24

Basic (Double-side Bossed) (B)

CM2B Bore size Stroke Z1-XB24

G
Width across flats B2 H2 G 2xP 2 x NN
Width across flats B1 H1 (Rc, NPT, G) I

ø
2 x øEh8

NA
øD

MM Effective thread length

AL NA
2 x FL
Width across flats KA A K F
H S + Stroke F
ZZ + Stroke

Boss-cut

ZZ + Stroke

Female rod end

Female thread MM
Thread depth A1

3.5
H
ZZ + Stroke

[mm]
Bore size A AL B1 B2 D E F FL G H H1 H2 I K KA MM NA NN P S ZZ
20 18 15.5 13 26 8 20−​00.033 13 10.5 8 41 5 8 28 5 6 M8 x 1.25 24 M20 x 1.5 1/8 62 116
25 22 19.5 17 32 10 26−​00.033 13 10.5 8 45 6 8 33.5 5.5 8 M10 x 1.25 30 M26 x 1.5 1/8 62 120
32 22 19.5 17 32 12 26−​00.033 13 10.5 8 45 6 8 37.5 5.5 10 M10 x 1.25 34.5 M26 x 1.5 1/8 64 122
40 24 21 22 41 14 32−​00.039 16 13.5 11 50 8 10 46.5 7 12 M14 x 1.5 42.5 M32 x 2 1/4 88 154

Boss-cut [mm] Female Rod End [mm]

Bore size ZZ Bore size A1 H MM ZZ
20 103 20 8 20 M4 x 0.7 95
25 107 25 8 20 M5 x 0.8 95
32 109 32 12 20 M6 x 1 97
40 138 40 13 21 M8 x 1.25 125
* W
 hen a female thread is used, use a thin
wrench when tightening the piston rod.
* W
 hen a female thread is used, depending on the
material of the workpiece, use a washer etc., to
prevent the contact part at the rod end from being
deformed.

4
 High Durability Series

CM2-XB24

Axial Foot Bracket (L)

CM2L Bore size Stroke Z1-XB24
H
A K F G 2xP
Width across flats B1 AL H2 (Rc, NPT, G) G F
H1
Width across flats KA
øD

øI
2 x øLC

B
LH
Width across flats B2 4 x øLD
MM Width across flats NA
Y X S + Stroke X Y LX
LT

Z LS + Stroke LZ
ZZ + Stroke

Female rod end

ZZ + Stroke
H
3.5
Female thread MM
Thread depth A1

[mm]
Bore size A AL B B1 B2 D F G H H1 H2 I K KA LC LD LH LS LT LX LZ MM NA P S X Y Z ZZ
20 18 15.5 40 13 26 8 13 8 41 5 8 28 5 6 4 6.8 25 102 3.2 40 55 M8 x 1.25 24 1/8 62 20 8 21 131
25 22 19.5 47 17 32 10 13 8 45 6 8 33.5 5.5 8 4 6.8 28 102 3.2 40 55 M10 x 1.25 30 1/8 62 20 8 25 135
32 22 19.5 47 17 32 12 13 8 45 6 8 37.5 5.5 10 4 6.8 28 104 3.2 40 55 M10 x 1.25 34.5 1/8 64 20 8 25 137
40 24 21 54 22 41 14 16 11 50 8 10 46.5 7 12 4 7 30 134 3.2 55 75 M14 x 1.5 42.5 1/4 88 23 10 27 171

Female Rod End [mm]

Bore size A1 H MM ZZ
20 8 20 M4 x 0.7 110
25 8 20 M5 x 0.8 110
32 12 20 M6 x 1 112
40 13 21 M8 x 1.25 142
* W hen a female thread is used, use a thin
wrench when tightening the piston rod.
* When a female thread is used, depending on
the material of the workpiece, use a washer
etc., to prevent the contact part at the rod end
from being deformed.

* The bracket is shipped together with the product.

5
 High Durability Series

Longer Life Cylinder: Double Acting, Single Rod CM2-XB24

Rod Flange (F)

CM2F Bore size Stroke Z1-XB24
4 x øFD Width across flats B2
H2 G 2xP G
Mounting hole Width across flats B1 H1 NN
(Rc, NPT, G)

C2
FY

øD

øI
B

øE
2 x øFD FX MM Effective thread length FL
AL Width across flats NA 1.5
ø Mounting FZ Width across flats KA A K FT
hole
ø to ø Z
H S + Stroke F
ZZ + Stroke

Boss-cut

ZZ + Stroke

Female rod end

Female thread MM
Thread depth A1

3.5
H
ZZ + Stroke

[mm]
Bore size A AL B B1 B2 C2 D E F FL FD FT FX FY FZ G H H1 H2 I K KA MM NA NN P S Z ZZ
20 18 15.5 34 13 26 30 8 20−​00.033 13 10.5 7 4 60 − 75 8 41 5 8 28 5 6 M8 x 1.25 24 M20 x 1.5 1/8 62 37 116
25 22 19.5 40 17 32 37 10 26−​00.033 13 10.5 7 4 60 − 75 8 45 6 8 33.5 5.5 8 M10 x 1.25 30 M26 x 1.5 1/8 62 41 120
32 22 19.5 40 17 32 37 12 26−​00.033 13 10.5 7 4 60 − 75 8 45 6 8 37.5 5.5 10 M10 x 1.25 34.5 M26 x 1.5 1/8 64 41 122
40 24 21 52 22 41 47.3 14 32−​00.039 16 13.5 7 5 66 36 82 11 50 8 10 46.5 7 12 M14 x 1.5 42.5 M32 x 2 1/4 88 45 154

Boss-cut [mm] Female Rod End [mm]

Bore size ZZ Bore size A1 H MM ZZ
20 103 20 8 20 M4 x 0.7 95
25 107 25 8 20 M5 x 0.8 95
32 109 32 12 20 M6 x 1 97
40 138 40 13 21 M8 x 1.25 125
* W hen a female thread is used, use a thin
wrench when tightening the piston rod.
* When a female thread is used, depending on
the material of the workpiece, use a washer
etc., to prevent the contact part at the rod
end from being deformed.

* The bracket is shipped together with the product.

6
 High Durability Series

CM2-XB24

Head Flange (G)

CM2G Bore size Stroke Z1-XB24
Effective thread length FL
H2 Width across flats B2 2 x øFD
Width across flats B1 H1 NN G 2xP G 4 x øFD
Mounting hole

C2
(Rc, NPT, G) Mounting hole

FY
øD

øI

B
øE

MM AL Width across flats NA FX

Width across flats KA A K F FZ ø40
H S + Stroke FT ø20 to ø32
Z + Stroke
ZZ + Stroke

Female rod end

Female thread MM
Thread depth A1

3.5
H
ZZ + Stroke

[mm]
Bore size A AL B B1 B2 C2 D E F FL FD FT FX FY FZ G H H1 H2 I
20 18 15.5 34 13 26 30 8 20−​00.033 13 10.5 7 4 60 − 75 8 41 5 8 28
25 22 19.5 40 17 32 37 10 26−​00.033 13 10.5 7 4 60 − 75 8 45 6 8 33.5
32 22 19.5 40 17 32 37 12 26−​00.033 13 10.5 7 4 60 − 75 8 45 6 8 37.5
40 24 21 52 22 41 47.3 14 32−​00.039 16 13.5 7 5 66 36 82 11 50 8 10 46.5

[mm]
Bore size K KA MM NA NN P S Z ZZ
20 5 6 M8 x 1.25 24 M20 x 1.5 1/8 62 107 116
25 5.5 8 M10 x 1.25 30 M26 x 1.5 1/8 62 111 120
32 5.5 10 M10 x 1.25 34.5 M26 x 1.5 1/8 64 113 122
40 7 12 M14 x 1.5 42.5 M32 x 2 1/4 88 143 154

Female Rod End [mm]

Bore size A1 H MM ZZ
20 8 20 M4 x 0.7 95
25 8 20 M5 x 0.8 95
32 12 20 M6 x 1 97
40 13 21 M8 x 1.25 125
* W hen a female thread is used, use a thin
wrench when tightening the piston rod.
* When a female thread is used, depending on
the material of the workpiece, use a washer
etc., to prevent the contact part at the rod end
from being deformed.

* The bracket is shipped together with the product.

7
 High Durability Series

Longer Life Cylinder: Double Acting, Single Rod CM2-XB24

Single Clevis (C)

CM2C Bore size Stroke Z1-XB24
Effective thread length FL øCD
Width across flats B1 H1 NN G G
2xP
(Rc, NPT, G) øI

NA
øCI
øD
øE

MM AL CX
Width across flats KA A K F U NA
H S + Stroke L
Z + Stroke RR
ZZ + Stroke

Female rod end

Female thread MM
Thread depth A1

3.5
H
ZZ + Stroke

[mm]
Bore size A AL B1 CI CD CX D E F FL G H H1 I K KA L MM NA NN P RR S U Z ZZ
20 18 15.5 13 24 9 10 8 20−​00.033 13 10.5 8 41 5 28 5 6 30 M8 x 1.25 24 M20 x 1.5 1/8 9 62 14 133 142
25 22 19.5 17 30 9 10 10 26−​00.033 13 10.5 8 45 6 33.5 5.5 8 30 M10 x 1.25 30 M26 x 1.5 1/8 9 62 14 137 146
32 22 19.5 17 30 9 10 12 26−​00.033 13 10.5 8 45 6 37.5 5.5 10 30 M10 x 1.25 34.5 M26 x 1.5 1/8 9 64 14 139 148
40 24 21 22 38 10 15 14 32−​00.039 16 13.5 11 50 8 46.5 7 12 39 M14 x 1.5 42.5 M32 x 2 1/4 11 88 18 177 188

Female Rod End [mm]

Bore size A1 H MM ZZ
20 8 20 M4 x 0.7 121
25 8 20 M5 x 0.8 121
32 12 20 M6 x 1 123
40 13 21 M8 x 1.25 159
* W hen a female thread is used, use a thin
wrench when tightening the piston rod.
* When a female thread is used, depending on
the material of the workpiece, use a washer
etc., to prevent the contact part at the rod
end from being deformed.

8
 High Durability Series

CM2-XB24

Double Clevis (D)

CM2D Bore size Stroke Z1-XB24
Effective thread length FL øCD hole H10 +0.058
0
Axis d9 −0.040
CL
Width across flats B1 H1 NN G 2xP G −0.076
(Rc, NPT, G) øI

NA
øCI
øD
øE

MM AL U CX
Width across flats KA A K F CZ
H S + Stroke L NA
Z + Stroke RR
ZZ + Stroke

Female rod end

Female thread MM
Thread depth A1

3.5
H
ZZ + Stroke

[mm]
Bore size A AL B1 CD CI CL CX CZ D E F FL G H H1 I K KA L MM NA NN P RR S U Z ZZ
20 18 15.5 13 9 24 25 10 19 8 20−​00.033 13 10.5 8 41 5 28 5 6 30 M8 x 1.25 24 M20 x 1.5 1/8 9 62 14 133 142
25 22 19.5 17 9 30 25 10 19 10 26−​00.033 13 10.5 8 45 6 33.5 5.5 8 30 M10 x 1.25 30 M26 x 1.5 1/8 9 62 14 137 146
32 22 19.5 17 9 30 25 10 19 12 26−​00.033 13 10.5 8 45 6 37.5 5.5 10 30 M10 x 1.25 34.5 M26 x 1.5 1/8 9 64 14 139 148
40 24 21 22 10 38 41.2 15 30 14 32−​00.039 16 13.5 11 50 8 46.5 7 12 39 M14 x 1.5 42.5 M32 x 2 1/4 11 88 18 177 188
* A clevis pin and retaining rings (split pins for ø40) are shipped together with the product.

Female Rod End [mm]

Bore size A1 H MM ZZ
20 8 20 M4 x 0.7 121
25 8 20 M5 x 0.8 121
32 12 20 M6 x 1 123
40 13 21 M8 x 1.25 159
* W hen a female thread is used, use a thin
wrench when tightening the piston rod.
* When a female thread is used, depending on
the material of the workpiece, use a washer
etc., to prevent the contact part at the rod
end from being deformed.

9
 High Durability Series

Longer Life Cylinder: Double Acting, Single Rod CM2-XB24

Rod Trunnion (U)

CM2U Bore size Stroke Z1-XB24
Width across flats B2
G 2xP G NN
Width across flats B1 H1 (Rc, NPT, G)
øTD

øD

øI
øTY

øE
MM Width across flats NA Effective thread length FL
TX AL
Width across flats KA A K TT
TZ
Z
H S + Stroke F
ZZ + Stroke

Boss-cut

ZZ + Stroke

Female rod end Female thread MM

Thread depth A1

3.5
H
ZZ + Stroke

[mm]
Bore size A AL B1 B2 D E F FL G H H1 I K KA MM NA NN P
20 18 15.5 13 26 8 20−​00.033 13 10.5 8 41 5 28 5 6 M8 x 1.25 24 M20 x 1.5 1/8
25 22 19.5 17 32 10 26−​00.033 13 10.5 8 45 6 33.5 5.5 8 M10 x 1.25 30 M26 x 1.5 1/8
32 22 19.5 17 32 12 26−​00.033 13 10.5 8 45 6 37.5 5.5 10 M10 x 1.25 34.5 M26 x 1.5 1/8
40 24 21 22 41 14 32−​00.039 16 13.5 11 50 8 46.5 7 12 M14 x 1.5 42.5 M32 x 2 1/4

[mm]
Bore size S TD TT TX TY TZ Z ZZ
20 62 8 10 32 32 52 36 116
25 62 9 10 40 40 60 40 120
32 64 9 10 40 40 60 40 122
40 88 10 11 53 53 77 44.5 154

Boss-cut [mm] Female Rod End [mm]

Bore size ZZ Bore size A1 H MM ZZ
20 103 20 8 20 M4 x 0.7 95
25 107 25 8 20 M5 x 0.8 95
32 109 32 12 20 M6 x 1 97
40 138 40 13 21 M8 x 1.25 125
* W hen a female thread is used, use a thin
wrench when tightening the piston rod.
* When a female thread is used, depending on
the material of the workpiece, use a washer
etc., to prevent the contact part at the rod
end from being deformed.

* The bracket is shipped together with the product.

10
 High Durability Series

CM2-XB24

Head Trunnion (T)

CM2T Bore size Stroke Z1-XB24
Effective thread length FL
NN G Width across flats B2
G 2xP
Width across flats B1 H1 (Rc, NPT, G)

øTD
øTY
øD

øI
øE

MM AL Width across flats NA TX

Width across flats KA A K F TZ
H S + Stroke TT
Z + Stroke
ZZ + Stroke

Female rod end

Female thread MM
Thread depth A1

3.5
H
ZZ + Stroke

[mm]
Bore size A AL B1 B2 D E F FL G H H1 I K KA MM NA NN P
20 18 15.5 13 26 8 20−​00.033 13 10.5 8 41 5 28 5 6 M8 x 1.25 24 M20 x 1.5 1/8
25 22 19.5 17 32 10 26−​00.033 13 10.5 8 45 6 33.5 5.5 8 M10 x 1.25 30 M26 x 1.5 1/8
32 22 19.5 17 32 12 26−​00.033 13 10.5 8 45 6 37.5 5.5 10 M10 x 1.25 34.5 M26 x 1.5 1/8
40 24 21 22 41 14 32−​00.039 16 13.5 11 50 8 46.5 7 12 M14 x 1.5 42.5 M32 x 2 1/4

[mm]
Bore size S TD TT TX TY TZ Z ZZ
20 62 8 10 32 32 52 108 118
25 62 9 10 40 40 60 112 122
32 64 9 10 40 40 60 114 124
40 88 10 11 53 53 77 143.5 154 * The bracket is shipped together with the product.

Female Rod End [mm]

Bore size A1 H MM ZZ
20 8 20 M4 x 0.7 97
25 8 20 M5 x 0.8 97
32 12 20 M6 x 1 99
40 13 21 M8 x 1.25 125
* W hen a female thread is used, use a thin
wrench when tightening the piston rod.
* When a female thread is used, depending on
the material of the workpiece, use a washer
etc., to prevent the contact part at the rod end
from being deformed.

11
 High Durability Series

Longer Life Cylinder: Double Acting, Single Rod CM2-XB24

Integrated Clevis (E)

CM2E Bore size Stroke Z1-XB24
LZ + Stroke
ZZ + Stroke
Z + Stroke LP
H S + Stroke L RR
A K F U NA
AL G 2xP G øCD CX
H1 (Rc, NPT, G)
øI

NA
øCI
øD
øE

LH
MM 2 x øLD
Width across flats B1 NN
Width across flats KA Effective thread length FL

LF LG

LT
LY LV
Refer to the Web Catalog for details
on the clevis pivot bracket.

Female rod end

Port 3.5
Integrated clevis (90°)(V) Female thread MM
Thread depth A1

H
* T
 he dimensions are the same as those for the ZZ + Stroke
integrated clevis (E).

[mm]
Bore size A AL B1 CD CI CX D E F FL G H H1 I K KA L MM NA NN
20 18 15.5 13 8 20 12 8 20−​00.033 13 10.5 8 41 5 28 5 6 12 M8 x 1.25 24 M20 x 1.5
25 22 19.5 17 8 22 12 10 26−​00.033 13 10.5 8 45 6 33.5 5.5 8 12 M10 x 1.25 30 M26 x 1.5
32 22 19.5 17 10 27 20 12 26−​00.033 13 10.5 8 45 6 37.5 5.5 10 15 M10 x 1.25 34.5 M26 x 1.5
40 24 21 22 10 33 20 14 32−​00.039 16 13.5 11 50 8 46.5 7 12 15 M14 x 1.5 42.5 M32 x 2

[mm]
Bore size P RR S U Z ZZ
20 1/8 9 62 11.5 115 124
25 1/8 9 62 11.5 119 128
32 1/8 12 64 14.5 124 136
40 1/4 12 88 14.5 153 165

Female Rod End [mm] Clevis Pivot Bracket [mm]

Bore size A1 H MM ZZ Bore size LD LF LG LH LP LT LV LY LZ
20 8 20 M4 x 0.7 103 20 6.8 15 30 30 37 3.2 18.4 59 152
25 8 20 M5 x 0.8 103 25 6.8 15 30 30 37 3.2 18.4 59 156
32 12 20 M6 x 1 111 32 9 15 40 40 50 4 28 75 174
40 13 21 M8 x 1.25 136 40 9 15 40 40 50 4 28 75 203
* W hen a female thread is used, use a thin
wrench when tightening the piston rod.
* When a female thread is used, depending on
the material of the workpiece, use a washer
etc., to prevent the contact part at the rod
end from being deformed.

12
 High Durability Series

CM2-XB24
Specific Product Precautions
Be sure to read this before handling the products. Refer to the back cover for safety
instructions. For actuator and auto switch precautions, refer to “Handling Precautions for
SMC Products” and the “Operation Manual” on the SMC website: [Link]

Handling

Warning Caution
1. Do not rotate the cover. 1. Cannot be disassembled
If a cover is rotated when installing a cylinder or screwing a fit- Cover and cylinder tube are connected to each other by caulk-
ting into the port, it is likely to damage the joint of the cover. ing method, thus making it impossible to disassemble. Parts
2. Operate the cylinder within the specified cylinder inside the cylinder, such as the rod seal, can never be re-
speed, kinetic energy, and lateral load at the rod placed.
end. 2. Do not touch the cylinder during operation.
3. The allowable kinetic energy is different between Use caution when handling a cylinder, which is running at a
the cylinders with male rod ends and with female high speed and a high frequency, because the surface of the
rod ends due to the different thread sizes. cylinder tube could get hot enough to burn you.

4. When a female rod end is used, depending on the 3. Do not use the air cylinder as an air-hydro cylinder.
material of the workpiece, use a washer etc., to pre- The use of turbine oil as a fluid for an air cylinder may result in
vent the contact part at the rod end from being de- oil leakage.
formed. 4. The oil stuck to the cylinder is grease.
5. Do not apply excessive lateral load to the piston rod. 5. The base oil of the grease may seep out.
Easy checking method The base oil of the grease in the cylinder may seep out of the
Min. operating pressure after the cylinder is mounted to the tube, cover, crimped part, or rod bushing depending on the op-
equipment (MPa) = Min. operating pressure of cylinder (MPa) erating conditions (ambient temperature 40°C or more, pres-
+ {Load mass (kg) x Friction coefficient of guide/Sectional area surized condition, low frequency operation).
of cylinder (mm2)}
6. When a rod end female thread is used, use a thin
If smooth operation is confirmed within the above value, the wrench when tightening the piston rod.
load on the cylinder is the resistance of the thrust only and it
can be judged as having no lateral load. 7. When using a rod end bracket and/or pivot bracket,
make sure they do not interfere with other brackets,
workpieces, rod section, etc.
8. Do not lubricate the cylinder.
Lubrication of the cylinder, using a lubricator, may cause mal-
function.
9. Do not wipe out the grease in the sliding part.
If grease applied to the sliding surface is removed, this can
cause malfunction and reduce the life of the cylinder.

Durability of The Cylinder

The durability of a longer life cylinder has been
evaluated by comparison with the existing cylinders
under SMC’s test conditions.
The durability of a cylinder depends on the customer’s
operating conditions and operating environment.
Therefore, durability of four times or longer will not be
guaranteed under all conditions.

13
 These safety instructions are intended to prevent hazardous situations and/or
Safety Instructions equipment damage. These instructions indicate the level of potential hazard with
the labels of “Caution,” “Warning” or “Danger.” They are all important notes for
safety and must be followed in addition to International Standards (ISO/IEC)∗1),
and other safety regulations.
∗1) ISO 4414: Pneumatic fluid power – General rules relating to systems.
Caution indicates a hazard with a low level of risk which,
Caution: if not avoided, could result in minor or moderate injury.
ISO 4413: Hydraulic fluid power – General rules relating to systems.
IEC 60204-1: Safety of machinery – Electrical equipment of machines.
(Part 1: General requirements)
Warning indicates a hazard with a medium level of risk which,
Warning: if not avoided, could result in death or serious injury.
ISO 10218-1: Manipulating industrial robots – Safety.
etc.
Danger indicates a hazard with a high level of risk which,
Danger : if not avoided, will result in death or serious injury.

Warning Caution
1. The compatibility of the product is the responsibility of the 1. The product is provided for use in manufacturing industries.
person who designs the equipment or decides its The product herein described is basically provided for peaceful use in
specifications. manufacturing industries.
Since the product specified here is used under various operating conditions, If considering using the product in other industries, consult SMC beforehand
its compatibility with specific equipment must be decided by the person who and exchange specifications or a contract if necessary.
designs the equipment or decides its specifications based on necessary If anything is unclear, contact your nearest sales branch.
analysis and test results. The expected performance and safety assurance
of the equipment will be the responsibility of the person who has determined Limited warranty and Disclaimer/
its compatibility with the product. This person should also continuously
review all specifications of the product referring to its latest catalog Compliance Requirements
information, with a view to giving due consideration to any possibility of The product used is subject to the following “Limited warranty and Disclaimer” and
equipment failure when configuring the equipment. “Compliance Requirements”.
Read and accept them before using the product.
2. Only personnel with appropriate training should operate
machinery and equipment. Limited warranty and Disclaimer
The product specified here may become unsafe if handled incorrectly. The
assembly, operation and maintenance of machines or equipment including
1. The warranty period of the product is 1 year in service or 1.5 years after
our products must be performed by an operator who is appropriately trained
the product is delivered, whichever is first.∗2)
and experienced. Also, the product may have specified durability, running distance or
replacement parts. Please consult your nearest sales branch.
3. Do not service or attempt to remove product and machinery/ 2. For any failure or damage reported within the warranty period which is clearly our
equipment until safety is confirmed. responsibility, a replacement product or necessary parts will be provided.
1. The inspection and maintenance of machinery/equipment should only be This limited warranty applies only to our product independently, and not to any
performed after measures to prevent falling or runaway of the driven other damage incurred due to the failure of the product.
objects have been confirmed.
3. Prior to using SMC products, please read and understand the warranty terms
2. When the product is to be removed, confirm that the safety measures as and disclaimers noted in the specified catalog for the particular products.
mentioned above are implemented and the power from any appropriate
∗2) Vacuum pads are excluded from this 1 year warranty.
source is cut, and read and understand the specific product precautions
A vacuum pad is a consumable part, so it is warranted for a year after it is delivered.
of all relevant products carefully. Also, even within the warranty period, the wear of a product due to the use of the vacuum pad
3. Before machinery/equipment is restarted, take measures to prevent or failure due to the deterioration of rubber material are not covered by the limited warranty.
unexpected operation and malfunction.
4. Contact SMC beforehand and take special consideration of
Compliance Requirements
safety measures if the product is to be used in any of the 1. The use of SMC products with production equipment for the manufacture of
following conditions. weapons of mass destruction (WMD) or any other weapon is strictly prohibited.
1. Conditions and environments outside of the given specifications, or use 2. The exports of SMC products or technology from one country to another are
outdoors or in a place exposed to direct sunlight. governed by the relevant security laws and regulations of the countries involved
2. Installation on equipment in conjunction with atomic energy, railways, air in the transaction. Prior to the shipment of a SMC product to another country,
navigation, space, shipping, vehicles, military, medical treatment, assure that all local rules governing that export are known and followed.
combustion and recreation, or equipment in contact with food and
beverages, emergency stop circuits, clutch and brake circuits in press
applications, safety equipment or other applications unsuitable for the Caution
standard specifications described in the product catalog.
SMC products are not intended for use as instruments for legal
3. An application which could have negative effects on people, property, or metrology.
animals requiring special safety analysis. Measurement instruments that SMC manufactures or sells have not been
4. Use in an interlock circuit, which requires the provision of double interlock qualified by type approval tests relevant to the metrology (measurement) laws
for possible failure by using a mechanical protective function, and of each country. Therefore, SMC products cannot be used for business or
periodical checks to confirm proper operation. certification ordained by the metrology (measurement) laws of each country.

Safety Instructions Be sure to read the “Handling Precautions for SMC Products” (M-E03-3) and “Operation Manual” before use.