SUBMITTAL FOR AERODUCT FLEXIBLE DUCT CONNECTOR

Project: U.G+G+3P+19+R RESIDENTIAL BUILDING W/ RETAIL AT GROUND

Location: Plot No. 6816166, AL BARSHA SOUTH FOURTH-681

Client: BASHAR MOHD TAISEER SAMHA

Consultant: CVTEC Consulting Engineers

Contractor: Al Wathba Building Cont. Co. LLC

MEP Subcontractor: M/S. Tariq Ziad Tech. Cont. LLC

P.O.Box 50673, Dubai Investments Park 2. | www.rhira.com | E: [email protected] | T: +971 4 8848 414
 Index

1. Product Catalogue and Technical Data

2. Compliance Statement and Schedule of Materials
3. Test Reports
4. Project Reference List
5. Project Approval Copies
6. Company Profile

P.O.Box 50673, Dubai Investments Park 2. | www.rhira.com | E: [email protected] | T: +971 4 8848 414
 1. Product Catalogue and Technical Data

P.O.Box 50673, Dubai Investments Park 2. | www.rhira.com | E: [email protected] | T: +971 4 8848 414
The Most
Comprehensive
Range of Ducting
Accessories
TABLE OF CONTENTS

Contents Page No.

Flexible Duct Connectors 1

Duct Fabric 4
Insulated Flexible Duct Connectors 5
Installation Guide – Flexible Duct Connectors 7
Flexible Ducts 8
Insulated Flexible Ducts 9
Uninsulated Flexible Ducts 11
Semi Rigid Flexible Ducts 12
PVC & Combo Flexible Ducts 13
Installation Guide – Flexible Ducts 15
Aeroduct Banding 16
Insulation Fasteners 17
Installation Guide – Insulation Fasteners 20
Project References 21

www.aeroduct.ae The Most Comprehensive Range of Ducting Accessories

 FLEXIBLE
DUCT
CONNECTOR
FLEXIBLE DUCT CONNECTORS

All mechanical equipment like Air Handling Units, Fan

Coil Units and Ventilation Fans generate noise and
vibrations when used. To eliminate the noise and
vibrations from transmitting through the air ducts, it is
necessary to install an airtight flexible joint between the
outlet of the equipment, and the inlet of the ducts.

The joint formed by attaching a layer of fabric to two

strips of metal on either side is called a "Flexible Duct
Connector".

The most critical part of this Flexible Duct Connector is

the fabric which has to be selected to suit the typical
requirements of each installation.

AERODUCT offers two types of dual lock of

metal-to-fabric mechanism:

1. Dual Lock Grip with 3 folds for 28 Gauge metal.

2. Dual Lock Grip with 2 folds for 24 Gauge metal.

Size
Length Metal
Part No. Metal x Fabric
(Feet) Gauge Specifications
x Metal (mm)

Vinyl

V-G8-145-75 45x75x45 75 28 Vinyl is the most commonly used

Fabric : Vinyl
V-G8-145-100 45x75x45 100 28 fabric for all air duct installations
Weight : 14oz./sq. yd (480 g/m2)
due to its high tear strength, and
V-G8-145-150 45x75x45 150 28 ± 5%
its high abrasion resistance.
V-G8-190-100 45x100x45 100 28 Tear Strength : 31 x 24 Kgs
Recommended for low to
62 x 53 lbs medium pressure ductwork
V-G8-230-100 70x100x70 100 28
Tensile Strength : 146 x 130 Kgs systems. Airtight and waterproof
V-G8-230-150 70x100x70 150 28 322 x 287 lbs construction.
V-G4-145-100 45x75x45 100 24 Burst Strength : 400 psi
V-G4-225-100 75x75x75 100 24 Temperature NFPA 701
V-G4-250-100 75x100x75 100 24 Range : -40deg C to 93 deg C
V-G4-300-100 75x150x75 100 24
V-G4-350-100 100x150x100 100 24

Neoprene

BSN-G8-145-100 45x75x45 100 28 Basic Fabric : Neoprene Neoprene is recommended for

Weight : 18oz./sq. yd (630 g/m2) use in application where high
BSN-G8-145-150 45x75x45 150 28 mechanical strength is required.
± 5%
BSN-G8-230-100 70x100x70 100 28 Tear Strength : 5.5 x 7 Kgs Neoprene is extremely resistant
12 x 15 lbs to most alkalies, gasoline and
BSN-G8-230-150 70x100x70 150 28 toxic fumes.
Tensile Strength : 592 x 350 Kgs
BSN-G4-145-100 45x75x45 100 24 1306 x 772 lbs Airtight and waterproof
construction.
BSN-G4-225-100 75x75x75 100 24 Burst Strength : 800 psi

BSN-G4-250-100 75x100x75 100 24 Temperature UV resistant.

BSN-G4-300-100 75x150x75 100 24 Range : -30deg C to 150 deg C

BSN-G4-350-100 100x150x100 100 24 Neoprene fabric does not

contain material that contribute
ODP or GWP

NFPA 701

www.aeroduct.ae The Most Comprehensive Range of Ducting Accessories 2

FLEXIBLE DUCT CONNECTORS

Size
Length Metal
Part No. Metal x Fabric Fabric Technical Specifications Features
(Feet) Gauge
x Metal (mm)

Silicon

Silicon fabric has a special Silicon

S-G8-145-100 45x75x45 100 28 Fabric : Silicon Rubber coating that has excellent
Weight : 16oz./sq. yd (560 g/m2) resistance to high and low
S-G8-230-100 70x100x70 100 28 ± 5% temperatures. Silicon is extremely
Tear Strength : 22 x 19 Kgs resistant to chemicals and ozone, and
emits very low smoke when burnt.
75x75x75 100 24 48 x 42 lbs
S-G4-225-100 Recommended for applications where
Tensile Strength : 228 x 171 Kgs high temperature is of main concern in
503 x 376 lbs both indoor and outdoor installations.
S-G4-250-100 75x100x75 100 24 Burst Strength : 450 psi Airtight and waterproof construction.
Temperature
S-G4-300-100 75x150x75 100 24 Range : -30 deg C to 300 deg C
UV resistant.

S-G4-350-100 100x150x100 100 24 Rated for use at 400 deg C for 2 hours

Achieves Class A when tested as

S-G4-145-100 45x75x45 100 24 per ASTM - E84 Surface Burning
Characteristics. NFPA 701

Canvas

Traditional Canvas cloth used for

C-G8-145-100 45x75x45 100 28 Fabric : Canvas air conditioning and ventilating
Weight : 16oz./sq. yd (535 g/m2) applications, indoors and
C-G8-220-75 60x100x60 75 28 ± 5% outdoors. Airtight and waterproof
Tear Strength : 4 x 4 Kgs construction.
C-G8-230-100 70x100x70 100 28 9 x 9 lbs
Tensile Strength : 127 x 96 Kgs
C-G8-280-100 70x150x70 100 28 280 x 210 lbs
Temperature
C-G8-300-100 75x150x75 100 28 Range : -40 deg C to 93 deg C

C-G4-300-100 75x150x75 100 24

Hypalon

Hypalon coated fabric has the

H-G8-145-100 45x75x45 100 28 Fabric : Woven Fiberglass
best resistance to ozone layer, and
Coating : Hypalon
is the first choice for outdoor
H-G8-230-100 70x100x70 100 28 Weight : 24oz./sq. yd (816 g/m2) applications. It has excellent
± 5% resistance to weathering, acids
H-G4-225-100 75x75x75 100 24 Tear Strength : 22 x 18 Kgs and is recommended for roof top
48 x 39 lbs applications. Airtight and
Tensile Strength : 102 x 136 Kgs waterproof construction.
H-G4-250-100 75x100x75 100 24
225 x 200 lbs
Burst Strength : 800 psi
H-G4-300-100 75x150x75 100 24
Temperature
Range : -40deg C to 121 deg C
H-G4-350-100 100x150x100 100 24

All AERODUCT Connectors have ODP = 0 & GWP < 5.

Sizes other than the above can be manufactured on request.
Tolerance applicable ± 5%.

www.aeroduct.ae The Most Comprehensive Range of Ducting Accessories 3

DUCT FABRIC

The complete range of AERODUCT fabrics are also available without metal for customers who have the need
for only the fabric. Standard roll widths are given in the table and are available in lengths of 100 feet and 150
feet.

Fabric Model No. Width of Fabric Length

Vinyl V-75-100 3" (75 mm) 100 feet

Vinyl V-100-100 4" (100 mm) 100 feet
Vinyl V-150-100 6" (150 mm) 100 feet
Neoprene BSN-75-100 3” (75 mm) 100 feet
Neoprene BSN-100-100 4” (100 mm) 100 feet
Neoprene BSN-150-100 6” (150 mm) 100 feet
Silicon S-75-100 3” (75 mm) 100 feet
Silicon S-100-100 4" (100 mm) 100 feet
Silicon S-150-100 6" (150 mm) 100 feet

Sizes other than the above can be manufactured on request.

Tolerance applicable ± 5%.

Typical Application

1. Dual Lock Grip with 3 folds for 28 Gauge metal. 2. Dual Lock Grip with 2 folds for 24 Gauge metal.

www.aeroduct.ae The Most Comprehensive Range of Ducting Accessories 4

 INSULATED FLEXIBLE DUCT CONNECTORS

For acoustically treated ductwork and supply ducts, it is

important that the fabric of the connector is also insulated
in addition to the insulation fixed on the ducting. This
enables the Flexible Duct Connector to achieve maximum
effectiveness.

Externally insulating the fabric, may damage the coating

on it, and also make it stiff thereby affecting the noise and
vibration absorption properties of the fabric. AERODUCT
has a complete range of “Insulated Duct Connectors”
which use a 25mm thick fibreglass insulation of R Value
4.2, sandwiched between two layers of fabric. The various
options of fabrics offered in insulated models, ensure that
the Flexible Duct Connectors can be used for all possible
types of ductwork installations. Thicker and higher density
fibreglass can be provided on request.

All models of Insulated Duct Connectors from AERODUCT

are available in 24 Gauge and 28 Gauge Steel.

www.aeroduct.ae The Most Comprehensive Range of Ducting Accessories 5

INSULATED FLEXIBLE DUCT CONNECTORS

Size
Length Metal
Part No. Metal x Fabric Specifications
(Feet) Guage
x Metal (mm)

VINYL

Fabric Fiberglass Insulation

ISV-G8-145-100 45x75x45 100 28
Fabric : Vinyl Insulation : Fiberglass 16 kg/m3,
ISV-G8-230-100 70x100x70 100 28
Weight : 2 x 14oz./sq. yd 25mm thickness
ISV-G8-280-100 70x150x70 100 24 (480 g/m2) ± 5% R Value : 4.2
Tear Strength : 31 x 24 Kgs
ISV-G4-145-100 45x75x45 100 24 62 x 53 lbs
ISV-G4-225-100 75x75x75 100 24 Tensile Strength : 146 x 130 Kgs
322 x 287 lbs
ISV-G4-250-100 75x100x75 100 24 Burst Strength : 400 psi
Temperature
ISV-G4-300-100 75x150x75 100 24 Range : -40deg C to 93 deg C

NEOPRENE

ISBSN-G8-145-100 45x75x45 100 28 Fabric Fiberglass Insulation

Fabric : Neoprene Insulation : Fiberglass 16 kg/m3,
ISBSN-G8-230-100 70x100x70 100 28
Weight : 2 x 18oz./sq. yd 25mm thickness
ISBSN-G8-290-100 70x150x70 100 28 (630 g/m2) ± 5% R Value : 4.2
Tear Strength : 5.5 x 7 Kgs
ISBSN-G4-145-100 45x75x45 100 24 12 x 15 lbs
ISBSN-G4-225-100 75x75x75 100 24 Tensile Strength : 592 x 350 Kgs
1306 x 772 lbs
ISBSN-G4-250-100 75x100x75 100 24 Burst Strength : 800 psi
Temperature
ISBSN-G4-300-100 75x150x75 100 24 Range : -30deg C to 150 deg C

SILICON

ISS-G8-145-100 45x75x45 100 28 Fabric Fiberglass Insulation

ISS-G8-230-100 70x100x70 100 28 Fabric : Silicon Insulation : Fiberglass 16 kg/m3,
Weight : 2 x 16oz./sq. yd 25mm thickness
ISS-G8-290-100 70x150x70 100 28 R Value : 4.2
(560 g/m2) ± 5%
ISS-G4-145 -100 45x75x45 100 24 Tear Strength : 22 x 19 Kgs
48 x 42 lbs
ISS-G4-225-100 75x75x75 100 24
Tensile Strength : 228 x 171 Kgs
ISS-G4-250-100 75x100x75 100 24 503 x 376 lbs
Burst Strength : 450 psi
ISS-G4-300-100 75x150x75 100 24
Temperature
Range : -30 deg C to 300 deg C
Rated for use at 400 deg C for 2 hours

Sizes other than the above can be manufactured on request.

Tolerance applicable ± 5%.

INTERNATIONAL TEST CERTIFICATES

Flexible Duct Connectors Flexible Ducts

www.aeroduct.ae The Most Comprehensive Range of Ducting Accessories 6

INSTALLATION GUIDE – FLEXIBLE DUCT CONNECTORS

Ensure that the notched side of the connector faces outward and position the joint in the middle of a side
rather than at a corner.

2. Holding the seam

1. Remove the roll from portion upwards to
the box, and cut the an angle of 90
connector to the degrees, make
required length. notches at the points
where bending is
required.

4. From the end of the

3. Bend the connector connector, cut away
to form the required the metal portion
shape. exposing only the
fabric, with length of
around 2 inches.

5. Join the two ends of

the sheet metal by
using rivets or screws. 6. Round Flexible
Apply a liberal amount connections can also
of adhesive on the be fabricated using
fabric portion under the the same procedure.
tongue, and hold the
joint for few seconds to
ensure the seal.

One side of the connector to be fixed with rivets on the mouth of the equipment and the other side to be
fixed with rivets onto duct.

www.aeroduct.ae The Most Comprehensive Range of Ducting Accessories 7

FLEXIBLE
DUCTS
INSULATED FLEXIBLE DUCTS

Specification Data

Specifications Insulated Insulated Insulated

No.
MODEL No ADI1 ADI1M ADI2

Double laminated film, Double laminated Triple laminated Alupet Foil

with black pigmented Metallized film, with film with Metallized film,
adhesive, permanently permanently bonded to permanently bonded to
Inner Core
1 bonded to corrosion helix corrosion resistant steel corrosion resistant steel wire
resistant steel wire. wire helix. helix.

Strong vapour barrier Strong vapour barrier Strong vapour barrier

2. Outer Jacket made from metallized film made from metallized film made from metallized film
laminate. laminate. laminate.

3. Insulation thickness 25mm / 38mm / 50mm 25mm / 38mm / 50mm 25mm / 38mm / 50mm

4. Density 16kg/m3 / 24kg/m3 16kg/m3 / 24kg/m3 16kg/m3 / 24kg/m3

5. R value 4.2 4.2 4.2

Maximum 10"w.g. - 4" - 16" 10" w.g.- 4" to 16" 10"w.g. - 4" - 16"
6.
Positive Pressure 6"w.g. - 18" - 20" 6" w.g. - 18 to 20" 6"w.g. - 18" - 20"

Maximum
7. 3/4"w.g. - All diameters 3/4"w.g. - All diameters 3/4"w.g. - All diameters
Negative Pressure

8. Maximum Velocity 5000 fpm 5000 fpm 5000 fpm

Operating -30 deg C to +150 deg C -30 deg C to +150 deg C -30 deg C to +150 deg C
9.
Temperature -20 deg F to +300 deg F -20 deg F to +300 deg F -20 deg F to +300 deg F

10. Standard Length 25 feet 25 feet 25 feet

11. Diameter 4" to 20" 4" to 20" 4" to 20"

BS 476, part 6 Class 0

12. Fire Rating - BS 476, part 6 Class 0 BS 476, part 7 Class1
BS 476, part 7 Class1 ASTM - E84

Sizes other than the above can be manufactured on request.

Tolerance applicable ± 5%.

www.aeroduct.ae The Most Comprehensive Range of Ducting Accessories 9

INSULATED FLEXIBLE DUCTS

Specification Data

Insulated - Reinforced Insulated - Reinforced Insulated - Reinforced

Specifications
No. Barrier Barrier Barrier
MODEL No ADIR1 ADIR2 ADIRA

Double laminated film, Triple laminated Alupet Foil

with black pigmented Film with Metallized Film,
adhesive, permanently permanently bonded to Multilayer Alupet foil film
1 Inner Core permanently bonded with
bonded to corrosion corrosion resistant steel
resistant steel wire helix. wire helix. galvanized steel helix wire.

Double laminated Double laminated Strong vapor barrier made

metallized film with metallized film with from multi-layer Alupet film
2. Outer Jacket fiberglass scrim reinforced fiberglass scrim reinforced combined with separate
vapour barrier. vapour barrier. strong fiberglass Reinforced
scrim.

3. Insulation thickness 25mm / 38mm / 50mm 25mm / 38mm / 50mm 25mm / 38mm / 50mm

4. Density 16kg/m3 / 24kg/m3 16kg/m3 / 24kg/m3 24kg/m3

5. R value 4.2 4.2 4.2/6/8

Maximum 10"w.g. - 4" - 16" 10"w.g. - 4" - 16"

6. 10"w.g.
Positive Pressure 6"w.g. - 18" - 20" 6"w.g. - 18" - 20"

Maximum
7. 3/4"w.g. - All diameters 3/4"w.g. - All diameters 3/4"w.g.
Negative Pressure

8. Maximum Velocity 5000 fpm 5000 fpm 3000 fpm

Operating -30 deg C to +150 deg C -30 deg C to +150 deg C -30 deg C to +150 deg C
9.
Temperature -20 deg F to +300 deg F -20 deg F to +300 deg F -20 deg F to +300 deg F

10. Standard Length 25 feet 25 feet 25 feet

11. Diameter 4" to 20" 4" to 20" 4" to 20"

UL181
BS 476, part 6 Class 0 BS 476, part 6 Class 0
ASTM E - 84
12. Fire Rating BS 476, part 7 Class1 BS 476, part 7 Class1
BS 476, part 6 Class 0
ASTM - E84
BS 476, part 7 Class1

Sizes other than the above can be manufactured on request.

Tolerance applicable ± 5%.

www.aeroduct.ae The Most Comprehensive Range of Ducting Accessories 10

UNINSULATED FLEXIBLE DUCTS

Specification Data

Specifications Uninsulated Uninsulated Uninsulated

No.
MODEL No ADUI3 ADUI4 ADUI5

Double laminated
Alupet foil film with Double laminated metallized Double laminated film
metallized film, film, permanently bonded to with black pigmented
1 Inner Core permanently bonded corrosion resistant steel adhesive, permanently
to corrosion resistant wire helix. bonded to corrosion
steel wire helix. resistant steel wire helix.

Maximum Positive 10" w.g.- 4" to 16" 10" w.g.- 4" to 16" 10" w.g.- 4" to 16"
2
Pressure 6" w.g.- 18" to 20" 6" w.g.- 18" to 20" 6" w.g.- 18" to 20"

Maximum Negative
3 1" w.g. All diameters 1" w.g. All diameters 1" w.g. All diameters
Pressure

4. Maximum Velocity 5000 fpm 5000 fpm 5000 fpm

Operating -30 deg C to + 150 deg C -30 deg C to + 150 deg C -30 deg C to + 150 deg C
5
Temperature -20 deg F to + 300 deg F -20 deg F to + 300 deg F -20 deg F to + 300 deg F

6 Standard Length 25 feet 25 feet 25 feet

7 Diameter 4" to 20" 4" to 20" 4" to 20"

8 Fire Rating BS 476, part 6 Class0 - -

BS 476, part 7 Class1

Sizes other than the above can be manufactured on request.

Tolerance applicable ± 5%.

www.aeroduct.ae The Most Comprehensive Range of Ducting Accessories 11

SEMI RIGID FLEXIBLE DUCTS

Specification Data

Specifications Uninsulated Insulated Insulated

No.
MODEL No ADSR ADISR ADISR1

Semi rigid aluminum Semi rigid aluminum flexible Semi rigid aluminum flexible
flexible duct is made from duct is made from aluminum duct is made from aluminum
1 Inner Core aluminum folded strips, folded strips, winded spirally. folded strips, winded spirally.
winded spirally. Aluminum Aluminum film sheet and leak Aluminum film sheet and leak
film sheet is leak proof proof interlock crimped. proof interlock crimped.
interlock crimped.

Strong vapour barrier made Strong vapour barrier made

2 Outer Core -
from Alupet foil film laminate. from Metallized film laminate.

3 Insulation thickness - 25mm 25mm

4 Density - 16kg/m 3 16kg/m3

5 R value - 4.2 4.2

6" wg or 1495 Pascal 6" wg or 1495 Pascal

- All diameters - All diameters
Maximum
6 - Flexible stretchable and ideal Flexible stretchable and ideal
Pressure for low and medium pressure for low and medium pressure
application. application.

7 Maximum Velocity 8000 fpm 8000 fpm or 40.6 m/s 8000 fpm or 40.6 m/s

Operating -30 deg C to + 250 deg C -30 deg C to + 250 deg C -30 deg C to + 250 deg C
8
Temperature -20 deg C to + 480 deg C -20 deg F to + 480 deg F -20 deg F to + 480 deg F

9 Standard Length 3 meter 3 meter 3 meter

10 Diameter 4" to 12.5" 4" to 12.5" 4" to 12.5"

BS 476, part 7 Class1 BS 476, part 7 Class1

11 Fire Rating ASTM E84
BS 476 part 6 Class0 BS 476 part 6 Class0

3-meter length is compressed to 900 –1100 mm with compression ratio of 1:3.

Tolerance applicable ± 5%.

www.aeroduct.ae The Most Comprehensive Range of Ducting Accessories 12

PVC & COMBI FLEXIBLE DUCTS

Specification Data

Insulated Uninsulated Uninsulated

Specifications
No. Pvc Flexible Duct Pvc Flexible Duct Combi Flexible Duct
MODEL No ADI07 ADUI07 ADUI06
1 Inner Core PVC Permanently bonded PVC Permanently bonded Double Laminated PVC with
to corrosion resistant steel to corrosion resistant steel Aluminium Foil Polyester film,
wire wire Permanently bonded to
corrosion resistant steel wire
helix.

2 Outer Jacket LDPE - -

3 Nominal Diameter (ID) 3" to 12.5" (80 mm - 315 mm) 3" to 12.5" (80 mm - 315 mm) 3" to 12.5" (80 mm - 315 mm)

4 Insulation Thickness 25 mm - -

5 Insulation Density 16 kg/m - -

6 R Value 4.2 - -

6 Standard Length 5 - 10 Meter & 25 Feet 5 - 10 Meter & 25 Feet 5 - 10 Meter & 25 Feet

7 Heating Temperature 20-100 °C 25-150 °C 25-150 °C

8 Operating Pressure 1495 Pascal - all diameters 1495 Pascal - all diameters 2000 Pascal max- all diameters

9 Operating Temperature -20°C to + 80°C -20°C to + 80°C -20°C to + 80°C

10 Maximum Air Velocity 20 m/s max 20 m/s max 25 m/s max

11 Available Options Upon Grey Standard Color & Grey Standard Color & Black Standard Color &
Request Customized Color Options Customized Color Options Customized Color Options
Customized lengths Customized lengths Customized lengths

Tolerance applicable ± 5%.

www.aeroduct.ae The Most Comprehensive Range of Ducting Accessories 13

FLEXIBLE DUCTS

Main Features
Economical solution to connecting equipment in air conditioning and ventilation systems, across a broad
spectrum of applications such as residential, commercial and industrial projects
Flexible construction renders ease of installation in areas where rigid ducts cannot be fixed
Ideal for use in low to medium pressure ductwork systems
Options for insulated and uninsulated models
Tear and puncture resistant construction

Pressure Loss Diagram

www.aeroduct.ae The Most Comprehensive Range of Ducting Accessories 14

INSTALLATION GUIDE – FLEXIBLE DUCTS

CONNECTIONS SPLICES

Cut completely around and through the duct with Fold Fold back jacket and insulation from core. Butt 2
knife or scissors. Cut the wire with wire cutters. Fold cores together on a standard 4" (100mm) length
back the jacket and insulation metal sleeve.

Slide at least 1" (25mm) of core over fitting and past Use atleast 2 wraps of duct tape to tape the jacket.
the bead. Seal core to cover with 2 wraps of duct Secure the connection with Aeroduct clamp placed
tape. Secure the connection with Aeroduct clamp over the core and tape and past the bead.
placed over the core and tape and past the bead.

Pull jacket and insulation back over the core. Use Pull jacket and insulation back over cores. Use atleast
atleast 2 wraps of duct tape to tape the jacket. You 2 wraps of duct tape to tape the jacket.
may use a clamp along with or instead of the duct
tape.

Precautions during installation:

Aeroduct insulated ducts use fiberglass insulation which is classified as a possible cancer hazard by
inhalation. In addition fiberglass insulation may cause temporary irritation to the eyes and skin. Kindly ensure
that protective clothing, face mask and gloves are used while handling or installing the flexible ducts. Wash
hands properly with soap and water after use.

www.aeroduct.ae The Most Comprehensive Range of Ducting Accessories 15

AERODUCT BANDING

Model Size Packaging per box

ADGSB09-6-30 0.6mm (Thickness) x 09mm (Width) 30 MTR

ADBL09 09mm (Width) 50 Pieces

Tolerance applicable ± 5%.

GALVANIZED STEEL
Aeroduct Banding are galvanized zinc protected steel. This is most popular clip in our
range. Ideally suited for most day requirements for joining hose in areas such as the
HVAC industry and the automotive aftermarket, agricultural application, such as
irrigation and farm machinery, pneumatic and hydraulic application in the industrial
sector, hardware/DIY applications and in construction.

www.aeroduct.ae The Most Comprehensive Range of Ducting Accessories 16

INSULATION FASTENERS
INSULATION FASTENERS

Insulation Fasteners (IF) / PERFORATED BASE HANGERS (PIF)

Base : 28 Gauge Metal Pin: Aluminium Plated
Size : 50mm x 50mm Packaging: 500 pieces per box with Steel Washers

Self Adhesive Perforated Pin Length Use for

Base Type Base Type (inches/mm) Insulation size
Model No. Model No.

IFAS34 PIFAS 34 0.75" / 19mm 1/2"

IFAS114 PIFAS 114 1.25" / 32mm 1"

IFAS 134 PIFAS 134 1.75" / 45nnm 11/2"

IFAS200 PIFAS 200 2.0" / 51 mm 11/2" Self Adhesive Type - Aluminium Nail
Reinforced and plain base options
IFAS250 PIFAS 250 2.5" / 65mm 2"

IFAS300 PIFAS 300 3.0" / 75mm 2.5"

IFAS80M PIFAS 80M 80mm 3"

IFAS400 PIFAS 400 4.0" / 100mm 3.5"

IFAS450 PIFAS 450 4.5" / 110mm 4"

IFAS120M PIFAS 120M 120mm 4"

Self adhesive type-Aluminium nail
IFAS130M PIFAS 130M 130mm 4.5"
Easy to bend and cut
IFAS140M PIFAS 140M 140mm 5"

IFAS 150M PIFAS 150M 150mm 5.5"

IFAS160M PIFAS 160M 160mm 6"

Tolerance applicable ± 5%.

Note: 1 inch is equivalent to 25mm.

Custom lengths available upon request.
Perforated Base Type Available
in Aluminium nail.

Insulation Fasteners Compact (IFCAS)

Base : 28 Gauge Metal Pin: Aluminium Plated
Size : 35mm x 35mm Packaging : 1000 pieces per box with two boxes of Steel Washers

Pin Length Use for

Model No.
(inches) Insulation size

IFCAS 114 1.25 1"

IFCAS 134 1.75 11/2"
IFCAS 200 2.0 11/2"
IFCAS 250 2.5 2"

Tolerance applicable ± 5%.

The steel base is made from 28 Gauge metal, a steel pin and double sided self adhesive tape having high
shear strength. The use of this pin prevents corrosion on the sheet metal which is caused by the welding
fasteners.

www.aeroduct.ae The Most Comprehensive Range of Ducting Accessories 18

INSULATION FASTENERS

SW Washers

Model No. Description pieces per box

SW Steel Washers 28 Gauge Galvanized 500

Tolerance applicable ± 5%.

Adhesive Tape Technical Details

Base Material : Polyethylene foam with aggressive pressure sensitive solvent acrylic adhesive
Service Temperature: -5 deg C to +65 Deg C.
Highly resistant to abrasion, corrosion and moisture.
Confirms to European Directive 2000/53 (Lead, Chromium VI, Mercury, Cadmium free)
10 Minute 180 degree Peel Adhesion: 30 N/25mm
500 Hour Static Shear (Stainless Steel): 0.8 kg/cm2

Duct Liner Installation

Dimensions
Velocity
A B C D E

0-2500 FPM 3" 12" 4" 6" 18"

(0-12.7 MPS) (76.2) (305) (102) (152) (457)
2501-6000 FPM 3" 6" 4" 6" 16"
(12.7-30.5 MPS) (76.2) (152) (102) (152) (406)

Metal Nosing Channel or Zee

Interior width of 8"(200mm) and less does not require pins

www.aeroduct.ae The Most Comprehensive Range of Ducting Accessories 19

INSTALLATION GUIDE – INSULATION FASTENERS

Ensure that the surface is clean and dry, Remove protection paper from
free from oil, grease or any dust particles the base of the insulation fastener.

Apply glue to the base of the perforated Firmly press the base of the pin at the
hanger and fix to the surface required position on to the stell surface

Fix the insulation over the pins Lock the insulation firmly to the steel
surface using the steel washers provided.

www.aeroduct.ae The Most Comprehensive Range of Ducting Accessories 20

PROJECT REFERENCES

WORLD TRADE CENTER WADI AL SAFA

DUBAI, UAE DUBAI, UAE

AETERNITAS TOWER ABU DHABI AIRPORT,

DUBAI, UAE UAE

DAS ISLAND RESIDENTIAL REEM MALL

DEVELOPMENT, ABU DHABI, UAE ABU DHABI, UAE

BALGHAIYLAM DEVELOPMENT KING KHALID AIRPORT,

ABU DHABI, UAE KSA

www.aeroduct.ae The Most Comprehensive Range of Ducting Accessories 21

PROJECT REFERENCES

SAUDI ENTERTAINMENT SULIMAN AL HABIB HOSPITAL,

VENTURES, KSA KSA

DIRIYAH GATE, KSA AMAN HOSPITAL,

QATAR

BURJ DAMAC SEAR VIEWS WALDROF ASTORIA,

APARTMENT, QATAR QATAR

MARINA MIX 004 TOWER PROJECT, LUSAIL PLAZA TOWERS,

QATAR QATAR

www.aeroduct.ae The Most Comprehensive Range of Ducting Accessories 22

CERTIFICATES

www.aeroduct.ae The Most Comprehensive Range of Ducting Accessories 23

 GLOBAL FOOTPRINT

CATALOG_AERODUCT_UAE_22MAY25

www.rhira.com
 2. Compliance Statement & Schedule of Materials

P.O.Box 50673, Dubai Investments Park 2. | www.rhira.com | E: [email protected] | T: +971 4 8848 414
 COMPLIANCE STATEMENT
Project: U.G+G+3P+19+R RESIDENTIAL BUILDING W/ RETAIL AT GROUND
Location: Plot No. 6816166, AL BARSHA SOUTH FOURTH-681
Client: BASHAR MOHD TAISEER SAMHA
Consultant: CVTEC Consulting Engineers
Contractor: Al Wathba Building Cont. Co. LLC
MEP Subcontractor: M/S. Tariq Ziad Tech. Cont. LLC

SR. SPECIFICATION PROPOSAL REMARKS

NO.

2.9 FLEXIBLE CONNECTORS

A. General: Flame-retarded or Proposed Aeroduct flexible duct Comply

noncombustible fabrics, coatings, and connector is having UL classified fabric
adhesives complying with UL 181,
Class 1.

B. Standard Metal-Edged Connectors: Proposed models of Aeroduct flexible Comply

Factory fabricated with a strip of fabric duct connector will have 100mm wide
89 mm wide attached to two strips of fabric attached with two strips of 75mm
70-mm- wide, 0.7-mm- thick, metal of 24 guage galvanized steel.
galvanized, sheet steel or 0.8-mm alu-
minum sheets. Select metal
compatible with connected ducts.

C. Conventional, Indoor System Flexible Proposed Aeroduct Flexible duct Comply as

Connector Fabric: Glass fabric double connector BSN-G4-250-100. It is proposed
coated with polychloroprene. having neoprene fabric
1. Minimum Weight: 880 g/sq. m. 1. Weight : 630 gms/sqmtr
2. Tensile Strength: 84 N/mm in 2. Tensile strength : 592 x 350 kgs
the warp, and 63 N/mm in the filling.

D. Conventional, Outdoor System Flexible Proposed Aeroduct Flexible duct Comply as

Connector Fabric: Glass fabric double connector S-G4-250-100. It is having proposed
coated with a synthetic- rubber, Silicon fabric
weatherproof coating resistant to the 3. Weight : 560 gms/sqmtr
sun's ultraviolet rays and ozone 4. Tensile strength : 81 x 90 kgs
environment.
1. Minimum Weight: 880 g/sq. m.
2. Tensile Strength: 93 N/mm in
the warp, and 77 N/mm in the filling.

P.O.Box 50673, Dubai Investments Park 2. | www.rhira.com | E: [email protected] | T: +971 4 8848 414
 SCHEDULE OF MATERIALS

Project: U.G+G+3P+19+R RESIDENTIAL BUILDING W/ RETAIL AT GROUND

Location: Plot No. 6816166, AL BARSHA SOUTH FOURTH-681
Client: BASHAR MOHD TAISEER SAMHA
Consultant: CVTEC Consulting Engineers
Contractor: Al Wathba Building Cont. Co. LLC
MEP Subcontractor: M/S. Tariq Ziad Tech. Cont. LLC

SR. MATERIAL PROPOSED MATERIAL

NO.

1 Flexible Duct Connector for Indoor Proposing Aeroduct flexible duct

use connector model BSN-G4-250-100,
75mm x 100mm x 75mm with Neoprene
fabric

Proposing Aeroduct flexible duct

2 Flexible Duct Connector for Outdoor and
connector model S-G4-250-100, 75mm
Fire area use x 100mm x 75mm with Silicon fabric

P.O.Box 50673, Dubai Investments Park 2. | www.rhira.com | E: [email protected] | T: +971 4 8848 414
 3. Test Reports

P.O.Box 50673, Dubai Investments Park 2. | www.rhira.com | E: [email protected] | T: +971 4 8848 414
 CERTIFICATE OF COMPLIANCE
Certificate Number 20130329-R27561
Report Reference R27561-20130329
Issue Date 2013-MARCH-29

Issued to: HIRA INDUSTRIES L L C

DUBAI INVESTMENTS PARK - 2
DUBAI UNITED ARAB EMIRATES

This is to certify that AIR DUCT VIBRATION ISOLATION CONNECTORS

representative samples of Aeroduct Vibration Isolation Connectors identified as Vinyl,
Silicon Coated Fiberglass and Neoprene Coated
Fiberglass.

Have been investigated by UL in accordance with the

Standard(s) indicated on this Certificate.

Standard(s) for Safety: NFPA 701- Standard Methods of Fire Tests for Flame
Propagation of Textiles and Films – Methods 1 and 2
Additional Information: See the UL Online Certifications Directory at
www.ul.com/database for additional information

Only those products bearing the UL Classification Mark should be considered as being covered by
UL’s Classification and Follow-Up Service.

The UL Classification Mark includes: UL in a circle: with the word “CLASSIFIED” (as shown); a control
number (may be alphanumeric) assigned by UL; a statement to indicate the extent of UL’s evaluation of
the product; and the product category name (product identity) as indicated in the appropriate UL
Directory.

Look for the UL Classification Mark on the product.

William R. Carney, Director, North American Certification Programs

UL LLC

Any information and documentation involving UL Mark services are provided on behalf of UL LLC (UL) or any authorized licensee of UL. For questions, please
contact a local UL Customer Service Representative at www.ul.com/contactus

Page 1 of 1
 ffil
ililrmxare
IlGml5ilE{

TEST REPORT
LAB ANALYSIS OF AERODUCT VINYL FABRIC

Report date: 11 lO8l2O13

Report number 9/13/395/J Source : CLIENT

Client HIRA INDUSTRIES

Sample description as AERODUCT VINYL Sampled by : MUMBAI LAB
identified bv the client FABRIC
Sample Marked As AERODUCT VINYL FABRIC
Location DUBAI Date tested 17 t07 12013 TO 22t07 t2013
Sampling method N/A Sample Quantity N/A

CHEMIGAL ANALYSIS:-

Result
Sr. No Test Done

01, Ozone Depletion Potential ODP 0

02. Global Warming Potential GWP <5

Note: Sample Consumed during testing.

Remark: - Pertaining to doesn't Contain materials that contribute to ODP or GWP.

#,$ s;\{o,'
a f.*sr6c\
o,o r'r.0

qr tr)
.::ljr'^$
ts - ts1"

S.A DUBAI

We Eureau Veritas certify that the above tests were carried out in an accredited lab, in accordance with official Methods of and witnessed
by Bureau Veritas.
 4. Project Reference List

P.O.Box 50673, Dubai Investments Park 2. | www.rhira.com | E: [email protected] | T: +971 4 8848 414
 5. Project Approval Copies

P.O.Box 50673, Dubai Investments Park 2. | www.rhira.com | E: [email protected] | T: +971 4 8848 414
007
 *tA,$fti
fl ur,*Jl f{l Iirr,tr..;;i:r;..
ti."'rtiit
p; .,.e.*,* *.*
H
!P
B',*** --

PROJECT [rl0: 694

PLOT NO.JVC12MHRS006 AREA :Jumeirah Viiltage Community, Dubai
CLIEhIT CONSULTANT COhITRACTCIR
R.S. Properties Managernent ALMAKTAB AL ASRI Tean: ErigineerinE
tri
[ 0 [- ENGINEERING CONSULT'ANT Enterprises Ltd"

RET NO. MATERIAI. SUB MITTAI. DATE

lv{ECH-AC-013 M"E.P 1 -Jun-1 7

Materiel Attachrnents {Reference

Flexible Dr";ci Connecior- B.O Q Scecifications

(ri) Brochure '13
Section "l 5820
Manufacturer (r,) Cataloque
( ) Guarantee Use
lr4ls Aeroduct lndustries LLC (V)Sample r\i nlana For purpose
Atlachment: 3 Sets Hard Copy +
Sample Duct conirectiern Prevention of Vibration
guFplier $pecified Alternative Froposal
Material Material Reason
:#sl*Sh" NIA I'J/A

"'#Sffips)\ Coltrafiof*sname Approval requested Consuitant"s recipt

'frfffi1 ><,}/ /Stamp & bv ( Date ) Dale.esRrr\

Siq.n-

\4'\'-'i#rv-"'J-.1:-
C)

&**S**'.'iY
For Consultant's Use
Approved Apprr:veC \"r' rieje cted
Subiect to Conimenls
Comnrents

APPROVED, subject to Coniractor's responsibility for:

. The material approvalfrom all authorities.
. Compliance with specs, contract & regulations.
o Coordination and proper application on site.
c Following manufacturer's inEtruction$.
. Tests to be applied as it may be required.
o uL (}-rlif i"J e> Wr SW€s-
Stamp & Sign Stamo & Sion Sign Upon Fixing*
( Proiect Enqineer ) ( Executiv&[nan"a o"rX ( Prcject Engineer
' NOTE Upcn fixing this material at site,rfift?NactorAffiil-ediain t)9e consultanf's re-
a1-rprovai vrithout which palmerrt mav\ot Ce'dteasec ii; '.t'l ',.,i (€ fl Vtl:
,' -/f"
(:(""n fil{ "r 7 JUflv znl"r

\nh
Material Approval Request (MAR) Form
Document Ref. No. 60020-MAT-S105400-HV-000024(1) Confidential ☐ Yes ‫ ܈‬No

Project Name Expo 2020 Development Package Project Reference No. S10

Thematic District Main

Contract No. 60020 Contract Title
Contractor

Contractor Name Al Futtaim Carillion Inspection Request No. Inspection Req. No.

Material Details
Name Model Number Supplier

Material Submittal for Flexible

Ramesh Hira
Insulated Duct
Manufacturer Country of Origin Sample Location

Aeroduct UAE N/A

Description Drawing Reference Specification

Material Submittal for Flexible Supporting Specification Information

Click here to enter text.
Insulated Duct Rev.A

Attachments Yes/No Comments

Related IFC Drawings (or Standard Drawing
YES Enter comments
from Authority/s), Specifications and BOQ

Technical Literature/Data Sheet YES Enter comments

Material/Lab Test Certificate YES Enter comments

Previous Test Results NO Enter comments

ISO 9001, ISO 14001 & OHSAS 18001 YES

Enter comments
Certificates

Trade or Commercial Licence YES Enter comments

Certificate of Compliance (For Individual NO

Enter comments
Material)

Compliance Statement (For Final/Finished YES

Enter comments
Product)

Sustainability Standard Certificate YES Enter comments

Environmental Product Declaration (For NO

Enter comments
Steel and Concrete only)

Chain of Custody Certificate (For Timber) YES Enter comments

Social and Environmental Policies NO Enter comments

Fire Fighting Certificate (For Exposed NO

Enter comments
Material)

PMC Template/Form
05007-FRM-P990000-QL-000013 Revision 4 Page 1 of 3
 Document Ref. No. 60020-MAT-S105400-HV-000024(1) Confidential ☐ Yes ‫ ܈‬No

Material Safety Data Sheet (MSDS) NO Enter comments

Samples YES Enter comments

Previous Authority Approval YES Enter comments

Details of Warranty YES Enter comments

Others YES Specify here.

Note:
x The requirements of above supporting documents shall be reviewed in accordance with the contract’s technical
specifications and the programme Assurance Minimum Standards. Where other supporting documents are
required but not in the list, it shall be provided under “Others”.
x The material submission shall be to the satisfaction of the engineer that the material offered is equal or superior to
and fully comply with the material specified in the contract’s technical specification. If full suppoting
documentation is not available at the time of submission, the contractor shall indicate on this form when the
respective documentation will be available for formal submission to the engineer.
x The material approval process is explained in the PMDS Activity Guide - Material Submission (Ref. 05007-ATG-
P990000-QL-000004).

Contractor’s Comment(s) or Additional Notes, if any.

Click here to enter text.

To Be Completed By the Engineer

Reviewer Name Position Comments Signature Date

Approved with Comments interms of Sustainability
Ashraf Ali Khan LEED AP 8-Feb-18
Perspective
1. Please confirm the compliance of Dubai Green
Building Regulations (DGBR) 502.11.
No objection for the proposed material subject with
comments.
1. Provide sample in the sample room for checking Felix Bordon 12-02-2018
Felix Bordon Mechanical
and approval.
2. Highlight the require density in the catalog as per
your proposed model number.(AD12) and specified
the pressure rating against the specification
requirements.
3.Contractor to ensure the specific location as
require in the approved drawing requirement in
accordance with the project specification and
standard.
4. Contractor to include the accessories in the
submittal for installations and provide sample @ site
for inspection and obtain approval from the
engineers.
5. Contractor to raise MIR upon the delivery
materials @ site and provide delivery note to obtain
PMC Template/Form approval from engineers and maintain proper
05007-FRM-P990000-QL-000013 Revision 4 handling/storage of approved materials to avoid Page 2 of 3
damages.
 Document Ref. No. 60020-MAT-S105400-HV-000024(1) Confidential ☐ Yes ‫ ܈‬No

Approver Name Position Comments Signature & Stamp Date

Gary White S.RE 24/02/2018

Engineer’s Comments

Please refer to & comply with the Engineer's comments on Page 2 of this document.
Material sample aaccepted.

Compliance against the Programme “Assurance Minimum Standards – Sustainability”:

‫ ܆‬Full Compliant
‫ ܆‬Part Compliant – Reasons: Specify here.
‫ ܆‬Not Compliant – Reasons: Specify here.

Material Approval Status:

‫ ܆‬Approved
‫܆‬
x Approved with Comments (Refer Engineer’s Comments Above)
‫ ܆‬Rejected

PMC Template/Form
05007-FRM-P990000-QL-000013 Revision 4 Page 3 of 3
 6. Company Profile

P.O.Box 50673, Dubai Investments Park 2. | www.rhira.com | E: [email protected] | T: +971 4 8848 414
 ® ®

1200
‘Hira Industries’ is dedicated to provide customers ‘Hira Industries’ aim’s to be a Global Leader in
in the Construction Sector with products of the niche products in building product industry. We
highest quality, by developing a successful aim to be the Market Leaders in the segments and
partnership with them, exceeding their expectations the regions we choose to compete in.
and gaining their trust through outstanding
performance by every member of our team. We
provide work environments where our employees
can meet their potential and thrive in an atmosphere
of professionalism. Our aim is to become the
“Employer of Choice” within the Building Product
HVAC Acessories
Industry.
 thermal

Hira Industries LLC embodies the factories for

rubber insulation, Aerofoam® NBR and for the cross
linked polyethylene insulation, Aerofoam® XLPE.
In both products, Hira Industries LLC controls the full
manufacturing process from foam extrusion up to
any value adding productive activity including
lamination, coating, compounding, conversion, etc.
Hira Industries LLC is the fastest growing foam
producing company within the GCC area, offering a
full range of quality products for the HVAC segment.
The permanent interest for new product
developments, the need of maintaining a competitive
price in the market and the wish to offer innovative
quality products make Hira Industries LLC one of the
few reliable solution-oriented players in the GCC,
Africa, Indian sub continent, Southeast Asia,
Americas, Australia and New Zealand. Hira
Industries LLC is committed to design, produce and
customize new generation thermal and acoustic
insulation foams used in the main HVAC fields.
ACOUSTIC SOLUTIONS
Providing adequate acoustic comfort has a substantial impact on our
well-being at home, as well as efficiency and concentration at work.
The most effective solution for acoustic comfort.

Compressor and Generator rooms

Hotels and manufacturing facilities

Wastewater pipe systems

Walls and Partitions

Air Ducts

Commercial and residential projects, Hospitals, Schools, etc.

FACTORY PREFABRICATED FITTINGS

Prefabricated AeroFittings are available in XLPE and flexible elastomeric foam.
These are made into different shapes such as Elbows, T and Y Sections.

Used for hot, chilled water pipes and air conditioning applications with
minimal cost of installation.

For outdoor application, Aerofoam® N-Clad fittings are recommended.

AIR BUBBLE FILMS
AeroPack consists of low density polyethylene film layers encapsulated with
air pockets in a symmetrical pattern.

Protective packing of fragile products

Courier, movers and logistics industries

Automobile industries

Retail supermarkets and malls

Furniture packaging

Packaging of electronic items (anti-static)

Packaging of pharmaceutical and dental products

Optical equipments

REFLECTIVE INSULATION
AeroReflect range is a thermal reflective insulation product which
prevents heat transfer by thermal radiations.

Residential constructions, new and retrofit – walls, ceilings, roofs, floors

and building crawl spaces.

Commercial complex, warehouse and shed walls, roofs and crawl

spaces.

Equipment sheds and pipe insulation

Garage, villas, auditorium, function halls, etc.

Dairy farm, animal kennels, poultry farm and livestock buildings

Temperature sensitive storage areas

Transport and recreational vehicles

MEP Installations

www.hirawalraven.com
Diamond Tapes, the Adhesive Tapes Division of Hira

Diamond Tapes has always opted for a service orient-

www.maicogulf.com
q c
HIRA CORPORATE OFFICE DUBAI, U.A.E.

HIRA WALRAVEN OFFICE DUBAI, U.A.E.

 HIRA RAK, U.A.E.

MAICO GULF, RAK, U.A.E.

 MAICO, INDIA

HIRA TECHNOLOGIES, INDIA

HIRA_COMPANYPROFILE_14SEP2020
 ‫رخصة صناعية‬
Industrial License
License Details / ‫تفاصيل الرخصة‬
License No. 536867 ‫رقم الرخصة‬

)‫م‬.‫م‬.‫ذ‬.‫هيرا للصناعة (ش‬ ‫اسم الشركة‬

Company Name HIRA INDUSTRIES )L.L.C(
)‫م‬.‫م‬.‫ذ‬.‫هيرا للصناعة (ش‬ ‫السم التجارى‬
Business Name HIRA INDUSTRIES )L.L.C(

Legal Type Limited Liability Company - Single Owner)LLC - SO( ).‫م‬.‫م‬.‫ الشخص الواحد (ذ‬- ‫شركة ذات مسؤولية محدودة‬ ‫الشكل القانونى‬
Expiry Date 19/08/2025 ‫تاريخ النتهاء‬ Issue Date 20/08/2002 ‫تاريخ الصدار‬

D&B D-U-N-S ® N 561246349 ‫الرقم العالمي‬ Main License No 536867 ‫رقم الرخصة الم‬
Register No. 1753156 ‫رقم السجل التجارى‬ DCCI No. 72664 ‫عضوية الغرفة‬

License Members / ‫الطراف‬

Share / ‫الحصص‬ Role / ‫الصفة‬ Nationality / ‫الجنسية‬ Name / ‫السم‬ No./‫رقم الشخص‬

100.00% Shares Owner / ‫مالك‬ British Virgin Islands / ‫جزر‬ ‫هيرا هولدينج كومباني ليمتد‬ 554141
‫حصص‬ ‫العذراء البريطانية‬
HIRA HOLDING COMPANY LTD
Manager / ‫مدير‬ India / ‫الهند‬ ‫بريان بيريرا‬ 1128510
BRYAN PEREIRA

License Activities / ‫نشاط الرخصة التجارية‬

Central Air-Conditioning Requisites Manufacturing ‫صناعة مستلزمات انظمة تكييف الهواء المركزية‬
Air-Conditioning Machines Manufacturing ‫صناعة أجهزة تكييف الهواء‬
Adhesives Manufacturing ‫صناعة مواد اللصق‬
Central Air-Conditioning Equipment Manufacturing ‫صناعة معدات تكييف الهواء المركزية‬
Unit Air-Conditioner Manufacturing ‫صناعة وحدات التكييف‬
Ventilation Equipment Manufacturing ‫صناعة معدات التهوية وتنقية الهواء‬
Insulation Materials Manufacturing ‫صناعة المواد العازلة‬
Rubber Products Manufacturing ‫صناعة المنتجات المطاطية‬

Print Date 19/08/2024 13:31 ‫تاريخ الطباعة‬ Receipt No. 15950266 ‫رقم اليصال‬
)‫اتصالت‬/‫ (دو‬6969 ‫ أرسل رقم الرخصة إلى‬،‫يمكنك الن تجديد رخصتك التجارية من خلل الرسائل النصية القصيرة‬
Get FREE access to
.‫للحصول على اذن الدفع‬
Zoho One for the first
Now you can renew your trade license by sending a text message )SMS(. Send your year
trade license number to 6969 )Du/ Etisalat( to receive payment voucher. - ‫احصل على زوهو ون مجانا‬
‫للسنة الولى‬ Zoho.com/det

‫لمراجعة صحة البيانات الواردة في الرخصة يرجي مسح رمزالستجابة السريعة‬. ‫وثيقة إلكترونية معتمدة وصادرة بدون توقيع من دائرة القتصاد والسياحة في دبي‬
this is a certified e-document issued without signature by the department of Economy and Tourism .Kindly Scan the QR Code to
Verify the certificate
 Address / ‫العنوان‬
Phone No 971-4-8848414 ‫تليفون‬ P.O. Box 50673 ‫صندوق بريد‬
Fax No 971-4-8848434 ‫فاكس‬ Parcel ID 0 ‫رقم القطعة‬
Mobile No 971-55-1091958 ‫هاتف متحرك‬ [email protected] Email / ‫البريد اللكتروني‬

‫م‬.‫م‬.‫ذ‬.‫مصنع ملك مجمع دبي للستثمار ش‬

Remarks / ‫الملحظات‬

Print Date 19/08/2024 13:31 ‫تاريخ الطباعة‬ Receipt No. 15950266 ‫رقم اليصال‬
)‫اتصالت‬/‫ (دو‬6969 ‫ أرسل رقم الرخصة إلى‬،‫يمكنك الن تجديد رخصتك التجارية من خلل الرسائل النصية القصيرة‬
Get FREE access to
.‫للحصول على اذن الدفع‬
Zoho One for the first
Now you can renew your trade license by sending a text message )SMS(. Send your year
trade license number to 6969 )Du/ Etisalat( to receive payment voucher. - ‫احصل على زوهو ون مجانا‬
‫للسنة الولى‬ Zoho.com/det

‫لمراجعة صحة البيانات الواردة في الرخصة يرجي مسح رمزالستجابة السريعة‬. ‫وثيقة إلكترونية معتمدة وصادرة بدون توقيع من دائرة القتصاد والسياحة في دبي‬
this is a certified e-document issued without signature by the department of Economy and Tourism .Kindly Scan the QR Code to
Verify the certificate
 ‫شهادة شهر قيد شركة فى السجل التجارى‬
Commercial Register
Register Details / ‫تفاصيل القــيد‬
Main Lice. Nr 536867 ‫ رقم الرخصة الم‬Register No. 1753156 ‫رقم القيد‬

Business Name )‫م‬.‫م‬.‫ذ‬.‫هيرا للصناعة (ش‬

HIRA INDUSTRIES )L.L.C(
Legal Type ‫الشكل القانونى‬
Limited Liability Company - Single .‫م‬.‫ الشخص الواحد (ذ‬- ‫شركة ذات مسؤولية محدودة‬
Owner)LLC - SO( ).‫م‬
Expiry Date 19/08/2025 ‫ تاريخ النتهاء‬Reg. Date 20/08/2002 ‫تاريخ الصدار‬
‫الرقم العالمي‬
D&B D-U-N-S ® No. 561246349

Capital Details / ‫تفاصيل راس المال‬

Nominated 300,000.00 ‫السمى‬
Paid 300,000 ‫المدفوع‬
No. of Shares 300 ‫عدد السهم‬
Currency UAE Dirhams ‫درهم اماراتي‬ ‫العملة‬

License Address / ‫عنوان الرخصة‬

‫م‬.‫م‬.‫ذ‬.‫مصنع ملك مجمع دبي للستثمار ش‬
Commerce Address / ‫عنوان السجل التجاري‬

‫م‬.‫م‬.‫ذ‬.‫مصنع ملك مجمع دبي للستثمار ش‬

Register Activities / ‫أنشطة السجل‬

Rubber Products Manufacturing ‫صناعة المنتجات المطاطية‬
Adhesives Manufacturing ‫صناعة مواد اللصق‬
Air-Conditioning Machines Manufacturing ‫صناعة أجهزة تكييف الهواء‬
Unit Air-Conditioner Manufacturing ‫صناعة وحدات التكييف‬
Ventilation Equipment Manufacturing ‫صناعة معدات التهوية وتنقية الهواء‬
Insulation Materials Manufacturing ‫صناعة المواد العازلة‬
Central Air-Conditioning Requisites Manufacturing ‫صناعة مستلزمات انظمة تكييف الهواء المركزية‬
Central Air-Conditioning Equipment Manufacturing ‫صناعة معدات تكييف الهواء المركزية‬
Insulation & Protection Materials Trading ‫تجارة المواد العازلة والواقية‬
Central Ventilators & Air-Filters Trading ‫تجارة معدات التهوية وتنقية الهواء المركزية‬
Air-Condition Trading ‫تجارة مكيفات الهواء‬
Rubber Trading ‫تجارة المطاط‬

Print Date 19/08/2024 13:31 ‫تاريخ الطباعة‬ Receipt No. 15950266 ‫رقم اليصال‬
)‫اتصالت‬/‫ (دو‬6969 ‫ أرسل رقم الرخصة إلى‬،‫يمكنك الن تجديد رخصتك التجارية من خلل الرسائل النصية القصيرة‬
Get FREE access to
.‫للحصول على اذن الدفع‬
Zoho One for the first
Now you can renew your trade license by sending a text message )SMS(. Send your year
trade license number to 6969 )Du/ Etisalat( to receive payment voucher. - ‫احصل على زوهو ون مجانا‬
‫للسنة الولى‬ Zoho.com/det

‫لمراجعة صحة البيانات الواردة في الرخصة يرجي مسح رمزالستجابة السريعة‬. ‫وثيقة إلكترونية معتمدة وصادرة بدون توقيع من دائرة القتصاد والسياحة في دبي‬
this is a certified e-document issued without signature by the department of Economy and Tourism .Kindly Scan the QR Code to
Verify the certificate
License no. 536867 536867 ‫رقم الرخصة‬

Membership no. 72664 72664 ‫رقم العضوية‬

Registration no. 1753156 1753156 ‫رقم السجل التجاري‬

Business Name HIRA INDUSTRIES (L.L.C) (‫م‬.‫م‬.‫ذ‬.‫هيرا للصناعة )ش‬ ‫السم التجاري‬

Legal Status Limited Liability Company - Sing ‫ الشخص‬- ‫شركة ذات مسؤولية محدودة‬ ‫الشكل القانوني‬

Activity Unit Air-Conditioner Manufacturing ‫صناعة وحدات التكييف‬ ‫نوع النشاط‬

Insulation Materials Manufacturing ‫صناعة المواد العازلة‬
Adhesives Manufacturing ‫صناعة مواد اللصق‬
Rubber Products Manufacturing ‫صناعة المنتجات المطاطية‬
Ventilation Equipment ‫صناعة معدات التهوية وتنقية الهواء‬
Manufacturing ‫صناعة أجهزة تكييف الهواء‬
Air-Conditioning Machines ‫صناعة مستلزمات انظمة تكييف الهواء‬
Manufacturing ‫المركزية‬
Central Air-Conditioning Requisites ‫صناعة معدات تكييف الهواء المركزية‬
Manufacturing
Central Air-Conditioning Equipment
Manufacturing

Member Since 20/08/2002 20/08/2002 ‫تاريخ النتساب‬

Date of Issue 20/08/2002 20/08/2002 ‫تاريخ الصدار‬

Expiry Date 19/08/2025 19/08/2025 ‫تاريخ النتهاء‬