8 7 6 5 4 3 2 1

NEITHER TO BE REPRODUCED OR DISPLAYED TO OTHERS NOR USED FOR THE MANUFACTURE OF MATERIAL B
NOTE : THIS PRINT AND THE DESIGN THERE IN IS THE PROPERTY OF THE ELECTROTHERM (INDIA) LTD AHMEDABAD

UNLESS SPECIFICALLY SO AUTHORISED IN WRITING BY AN OFFICER OF ELECTROTHERM (INDIA) LTD.

O 1800

F
F

COIL ID O 1130
B
AND IS ISSUED WITH THE UNDER STANDING THAT IT SHALL BE HELD IN CONFIDENCE,

FORMER O 850
14
12
200

300
E
95

E
A

A
9
1339
VERTICAL CHANNEL HEIGHT 1550
MOUNTING HEIGHT 1830

1368 WITH MICA

D D
TOTAL HEIGHT 2037

1230
80.5
CONNECTION SIDE
32 HEX NUT M 16 [Link].10.9 40 2.57
COIL HEIGHT

31 [Link] M16 55 [Link].10.9 40 5.24

30 SPRING WASHER B16 M.S. 40 0.32
29 PLAIN WASHER A18 M.S. 80 0.85
28 HEX NUT M16 S.S.304 8 0.32
27 SPRING WASHER B16 S.S. 304 8 0.08
26 PLAIN WASHER A18 S.S.304 16 0.18
25 [Link] M16 50 S.S.304 8 0.96
24 PRESSURE PAD 00 136 03 15 57 4 0 24 36.32
C 23 PRESSURE BOLT 00 135 09 20 07 4 1 106 M.S. IS: 1364 24 11.36 C
22 [Link] M20 H.T. 4 0.34
200

21 HEX BOLT M20 70 HT Gr 10.9 4 0.99

O 750
20 SPRING WASHER B20 M.S. 4 0.03
19 PLAIN WASHER A22 [Link] 8 0.13
18 BRACKET 00 161 03 01 06 4 0 4 8.51
9

129

17 RAMMING MASS AS SHOWN 1 1853.33

175

16 FORMER 00 018 03 80 13 4 0 1 226.03

15 SPIDER 00 019 01 60 09 4 0 1 1.68
86

14 TOP RING ASSY DA 000563 02 92 5 1 963.30

13 CHECK NUT M24 M.S. 24 1.67
230

200
80

180

12 LAMI STACK ASSY - 3 XL 000241 02 35 1 1 180.11

11 LAMI STACK ASSY - 2 XL 000241 02 35 1 1 180.12
275

10 LAMI STACK ASSY - 1 XL 000241 02 35 1 10 1795.47

195

59

B 9 LAMINATION INSU. PAD DA 000563 02 79 3 12 72.26 B

8 HEX NUT M 14 H.T. GR 10.9 48 1.28
7 HEX BOLT M 14 50 H.T. GR 10.9 48 4.20
6 SPRING WASHER B14 M.S. 48 0.26
5 PLAIN WASHER A16 M.S. 96 0.80
4 VERTICAL CHANNEL DA 000563 02 32 2 12 492.37
3 COIL ASSEMBLY DA 002175 02 10 1 1 581.82
O 1640
2 MICA SATHERM + COJI FOIL 5 1130 1190 . 2 0.00
P.C.D. 1755 1 BOTTOM RING ASSY. DA 000563 02 91 5 1 1568.02

O 1800 ITEM DESIGNATION DRG. NO./ SIZE THK LENGTH WIDTH/ID HEIGHT/OD MATERIAL QTY WEIGHT
u5

P.C.D.(FAB.)
2500 --
1500 u3
2500
SECTION A-A --
5000
u2
1500
-- u10

FABRICATION
3500 u7
5000
2500 3500 u5
NOTE:- 1500 2500 u4
A 200 1500 u3
(1) ALL DIMENSIONS ARE IN mm -- 200 u1
(2) TOTAL APPROX. WEIGHT 5938 Kg (WITHOUT FORMER, SPIDER, & RAMMING MASS) 1000 2000 u1.2

MACHINING
315 1000 u0.8
(3) PRESSURE BOLT TIGHTENING TORQUE=80 Nm EACH, 120 315 u0.5
ALTERATIONS Name Date APPD REMARKS
SHOULD BE TIGHTEN WITH TORQUE WRENCH. 30 120 u0.3 SCALE Drawn DEE 17/01/2022

(4) BEFORE FASTENING THIS S.S. BOLT WITH S.S. NUT APPLY ONE COAT OF GREASE EP-2 6
0.5
30
6
u0.2
u0.1
FURNACE ASSEMBLY N.T.S.
Checked
Standard
FOR EASY REMOVE OF NUT & BOLT. ABOVE UPTO TOL. R
R DRG. No. SHEET 1 OF 1
TOLERANCES FOR

8 7 6 5 4
DIMENSIONS WITHOUT
SPECIFIED TOLERANCE. INDIA LTD. AHMEDABAD XL 000241 02 00 1
S.C.:- 580000052284