VOLTAGE PROTECTION RELAY ACCURACY: KEY OPERATION MECHANICAL INSTALLATION

VPR 33-02A Class 1.0 (Standard) 1) To install the instrument on a DIN rail, raise the clamp at the
back of the instrument and place it on the rail. Now release
OUTPUT SPECIFICATION : FUNCTION PRESS KEY the clamp, so the instrument fits on the DIN rail.
OPERATOR MODE 2) Ensure proper fitting of the instrument by pulling it outwards.
Relay 2 nos. 3) To remove the instrument raise the clamp to release it from
To enter in parameter setting SET For 5 sec the DIN rail.
Relay Type 1 C/O (NO-C-NC) 4) The equipment in its installed state must not come in
5A, 230V AC Resistive Load close proximity to any heating source, caustic vapors, oil

<

<
Rating 24V DC To view individual phase voltage OR steam, or other unwanted process byproducts.
5) Do not connect anything to unused terminals.
ENVIRONMENT CONDITION :

<
To Scroll & Hold Page SET + MAINTENANCE
Operating Temp. 0°C to 55°C For 3 sec
1) The equipment should be cleaned regularly to avoid
UP to 95% RH To reset the relay contact in

<
Relative Humidity blockage of ventilating parts.
(non-condensing) manual mode after tripping 2) Clean the equipment with a clean soft cloth. Do not use
NETWORK CONNECTION : PARAMETER SETTING MODE isopropyl alcohol or any other cleaning agent.
It is used to set parameter value 3) Fusible resistor must not be replaced by operator.
3Ø-3W/3Ø-4W/1Ø-2W SET
and to be save & exit from menu INSTALLATION GUIDELINES
To increase value in parameter setting

<
Press 1Sec in Live fault value 1) Do not allow pieces of metal, wire clippings, or fine
MECHANICAL INSTALLATION metallic fillings from installation to enter the product or
To decrease value in parameter

<
else it may lead to a safety hazard that may in turn
setting & Press the key for 3 sec to endanger life or cause electrical shock to the operator.
TECHNICAL SPECIFICATION Front View(mm) Side View(mm) enter into last 5 fault history
2) Circuit breaker or mains switch must be installed
FEATURES : between power source and supply terminal to facilitate
61.5

Protection Available Asymmetry DISPLAY PAGE power ‘ON’ or ‘OFF’ function. However this mains switch
Over Voltage or circuit breaker must be installed at convenient place
Phase Loss 3Ø-4W 3Ø-3W 1Ø-2W normally accessible to the operator.
Under Voltage Phase Sequence 1) Voltage L1-N 1) Voltage L1-L2 1) Voltage L1-N
3) Use and store the instrument within the specified ambient
Over Frequency Neutral Loss temperature and humidity ranges as mentioned in this
Under Frequency Last 5 Fault History Indicate manual.
R1 R2 R1 R2 R1 R2

Reset Mode: Auto/ Manual 2) Voltage L2-N 2) Voltage L2-L3 2) Frequency

OR
Network Selection 3Ø-3W/3Ø-4W/1Ø2W ! SAFETY PRECAUTION
Time parameter: Power on delay, Trip delay TERMINAL CONNECTION
R1 R2 R1 R2 R1 R2 All safety related codifications, symbols and instructions
Recovery time (Auto Reset)
3) Voltage L3-N 3) Voltage L3-L1 that appear in this operating manual or on the equipment
INPUT SPECIFICATION : must be strictly followed to ensure the safety of the operating
160 to 300V AC (L - N) 3Ø-4W/1Ø-2W personnel as well as the instrument.
Direct Voltage AC
260 to 520V AC (L - L) 3Ø-3W R1 R2 R1 R2
If all the equipment is not handled in a manner specified
4) Voltage L1-L2 4) AVG Voltage
Frequency 45.0 Hz to 65.0 Hz by the manufacturer, it might impair the protection provided
Resolution 1 Volt VPR 33-02A by the equipment.
Power Supply: Self Powered Read complete instructions prior to installation
Accuracy Class 1.0 L1
R1 R2 R1 R2

5) Voltage L2-L3 5) Frequency

and operation of the unit.
L2 To
DISPLAY AND KEY : Load
L3 WARNING : Risk of electric shock.
N
Display UPPER: 3 Digit, 7 Seg, 0.4"
R1 R2 R1 R2
LOWER: 3 Digit, 7 Seg, 0.28"
6) Voltage L3-L1 6) Asymmetry %
WARNING GUIDELINES
Keys SET, INC, DEC/RST L1 L2 L3 N
Voltage Range
GENERAL SPECIFICATION : ( L - L ) 260 To 520V AC WARNING : Risk of electric shock.
VPR 33 ( L - N ) 160 To 300V AC
Dimension (mm) 90 (H) x 35 (W) x 61.5 (D) mm R1 R2 R1 R2

1) To prevent the risk of electric shock, power supply to the

7) AVG Voltage
Network Connection equipment must be kept OFF while doing the wiring
Trip Setting Under Voltage : 260-520V AC 3Ø-3W 3Ø-4W, 3Ø-3W, 1Ø-2W
160-300V AC 3Ø-4W/1Ø-2W arrangement. Do not touch the terminals while power is
NO C1 NC NO C2 NC being supplied.
Over Voltage : 260-520V AC 3Ø-3W R1 R2

160-300V AC 3Ø4W/1Ø-2W RELAY 1 RELAY 2 2) To reduce electro magnetic interference, use wire with
8) Frequency
adequate rating and twists of the same of equal size shall
Under Frequency : 45.0 Hz To 65.0 Hz be made with shortest connection.
Over Frequency : 45.0 Hz To 65.0 Hz 3. Cable used for connection to power source, must have a
Phase Asymmetry : (2-30%) R1 R2
cross section of 1mm or greater. These wires should have
Hysteresis : (0-99V) 9) Asymmetry %
insulations capacity made of at least 1.5kV.
Power ON Delay Time : 0.0 To 99.9 Sec. 4) A better anti-noise effect can be expected by using
Time Parameter
Trip delay Time : 0.0 To 999 Sec. Made in india standard power supply cable for the instrument.
R1 R2
Recovery Time : 0.0 To 99.9 Sec.
Page -1
 Press SET key

<
Press For Key

<
<
Press For Key

<
Press For Key Press For Key (Password)

<

<
for 5 sec Press For Key Press For Key
(Relay1) (Relay 2)
R1 R2 (Config) (Config)
Enter Password 45 R1 R2
(Config) R1 R2 R1 R2 R1 R2
R1 R2

<
Press SET key Press SET key
Press For Key
Press SET key Press SET key Press SET key
Press SET key
R1 R2
(Hysterisis Of Voltage) (Power On Delay Time) (Factor Reset)
Press SET key (Over Voltage) (Relay1 / Relay2 Selection)
(Password)
(0 To 99V) (0.0 To 99.9 Sec) (Yes / No)
(Enable / Disable)
(Network) R1 R2
R1 R2
R1 R2 R1 R2 R1 R2 (Enable / Disable)
Press SET key Press SET key Press SET key Press SET key Press SET key
R1 R2
(Config)
Press SET key
If over (Over Voltage Value) (Over Voltage) (Hysterisis Of Asymmentry) Main Page Main Page
If Network
Voltage ( Percentage)
Press SET key is Disable (260 To 520V 3Ø3W) (Enable / Disable) Selection 1Ø2W (Enter Password)
R1 R2
(0 To 5 %)
R1 R2 (160 To 300V 3Ø4W/1Ø2W) R1 R2
(Network Selection) Press SET key Press SET key
Press SET key R1 R2
(3Ø3W / 3Ø4W/ 1Ø2W)
R1 R2 Press SET key
If over (Over Voltage Value) (Hysterisis Of Frequncy)
Press SET key (Under Voltage) Voltage (260 To 520V 3Ø3W)
is Disable
(160 To 300V 3Ø4W/1Ø2W)
Main Page
(Enable / Disable) R1 R2 (0.0 / 5.0 Hz)
Main Page R1 R2
R1 R2
Press SET key For 5 Sec
Press SET key Press SET key To Save Parameter
Press SET key

(Under Voltage)
(Under Voltage Value) Main Page
If Under
Voltage
is Disable (260 To 560V 3Ø3W)
(Enable / Disable) FAULT MESSAGE
R1 R2
R1 R2 (160 To 300V 3Ø4W/1Ø2W)
Press SET key
Press SET key
◘ Over Voltage in
If Under (Under Voltage Value)
(Over Frequency) Voltage (260 To 520V 3Ø3W) or VL2 (3Ø-4W)
is Disable
(160 To 300V 3Ø4W/1Ø2W)
(Enable / Disable)
R1 R2
R1 R2

Press SET key

OV Over Voltage Value=280V
Press SET key
◘ Under Voltage in
(Over Frequency)
(Over Frequency Value) VL1(3Ø-4W)
If Over
Frequency (Enable / Disable)
(45.0 To 65.0Hz) R1 R2
is Disable
R1 R2
UV Under Voltage Value=180V
Press SET key
Press SET key

(Over Frequency Value)

◘ Over Frequency Fault
If Over
(Under Frequency) Frequency
◘ Over Frequency
is Disable (45.0 To 65.0Hz)
R1 R2
(Enable / Disable) R1 R2
Value=55.0 Hz
Press SET key
Press SET key
(Under Frequency) ◘ Under Frequency Fault
If Under (Under Frequency Value)
Frequency
is Disable
(Enable / Disable) ◘ Under Frequency
(45.0 To 65.0Hz) R1 R2

R1 R2
Press SET key
Value=45.0 Hz
Press SET key
If Under
◘ Asymmentry Voltage
Frequency (Under Frequency Value)
(Asymmetry) is Disable
(45.0 To 65.0Hz) between y & B Phase
(Enable/Disable) R1 R2 ◘ Asymmentry Voltage
R1 R2 PA
Press SET key
Press SET key = 10 %
(Asymmetry) (Trip Delay)
If (Asymmetry Value) (0.0 - 999 Sec)
Asymmetry
(2 To 30%) If Network R1 R2
(Enable/Disable)
R1 R2
◘ L3 - Phase loss
is Disable
Selection 1Ø2W
If Network R1 R2 Press SET key
Selection 1Ø2W Press SET key PL
Press SET key
If
Asymmetry (Asymmetry Value) (Reset Mode)
(Phase Loss) (Reset Mode) is Disable (2 To 30%) (Auto / Manual)
(Enable/Disable) (Auto /Manual) R1 R2 R1 R2 ◘ Phase sequence Fault
R1 R2 R1 R2 Press SET key
Press SET key
Press SET key Press SET key PS

(Phase Loss) (Recovery Time

If Manual Auto Reset Mode)
(Phase Sequence)
If Manual (Recovery Time Mode) (Enable/Disable) Reset mode (0.0 To 99.9 Sec)
Note : LED Status- blinking LED LED on LED off
Reset mode ( Auto Reset mode) R1 R2
select R1 R2
(Enable/Disable) select (0.0 To 99.9 Sec)
R1 R2 R1 R2
Press SET key Press SET key NOTE :-
Press SET key Press SET key
(Phase Sequence) (Relay Fault Mode)
- For Hold & Scroll Press SET
+ key for 3 Sec.
(Trip Delay) (Relay Fault Mode) (ON / OFF) - If Relay 2 Mode Selected R1 Then Relay 2 Parameter
(Enable/Disable)
(0.0 - 999 Sec) (ON / OFF) R1 R2 R1 R2 R1 = R2
R1 R2 R1 R2
Press SET key Press SET key - Press +
key for 3 Sec & Enter Password 21 Fault
Press SET key Press SET key History Reset Yes / No
Main Page
Main Page