Readthismanualcarefullybeforeoperatingthekitchen.

Instruction Manual and Warranty

Administration and factory Av. 25 de Mayo No. 1400
(1650) – San Martín Prov. of Buenos Aires.
Tel./ fax: 4754-1122
(10 rotating lines)
eScorial

Ppalace

Escorial

The ESCORIAL kitchens are products approved by the Argentine Gas Institute.
under NAG -312 norm - Year 2010- Enargas, for domestic use, regulated for a
Pressure of 1.76 kPa (180 mmCa) in natural gas and 2.74 kPa (280 mmCa) in gas.
packaging.
Congratulations and thank you for choosing us. To ensure the correct functioning and
to avoid inconveniences remember that:
The installation must be carried out by a registered installer and in
everything in accordance with the established provisions and regulations
minimums for the execution of home installations.
You have acquired a device of:
CLASS 2 - SUBCLASS 1 - ASSEMBLY DEVICE TO FIT BETWEEN TWO
FURNITURE.

Chapter 1: Instructions for the Installer.

Before installation, ensure that local distribution conditions are met (nature
the gas expression) and the adjustment of the devices should be compatible.
The adjustment conditions of this device are inscribed on the label (or plate of
marked), placed on the inner side of the side.
This device must not be connected to a product evacuation device.
combustion. Its installation and connection must be carried out in accordance with the regulations of
installation in force. Special attention must be paid to ventilation
in locations without permanent ventilation" and having doubts about the efficiency of the
existing ventilation, do not install the device without first consulting with a dedicated professional
this item.
To connect
Before we begin, we want to inform you that any material alteration performed
during installation, it voids the warranty.
This task begins with closing the shutoff valve that supplies gas to the installation.
Before connecting the gas, the appliance must be secured; for this purpose, you must take the
grandpa, (provided in the "fixing kit"), attach it to the back of the kitchen by bending the
tab, as shown in illustration 'A', then bring the kitchen closer to the wall, mark the
hole position, remove the stove, and with a drill perform the wall drilling, for the
wedge, then position the kitchen. Place the screw to anchor the clamp to the wall with a
side and the kitchen on the other. The device must be separated from the back wall by 20 mm. And
10 mm. From the side counters, this will allow for adequate ventilation and
It will protect the side coverings of the furniture.

1
Then connect the household gas supply to the bar, threaded entry piece for the
kitchen, (½” gas thread) taking it with a clamp, after threading, and with another, adjustment to
take from your home installation, once the task is finished, open the shut-off valve
of gas and check that there are no leaks.
See scheme: B

Lower tongue according to

model
Mod: Candor
Palace

Mod: Master

Scheme: A Scheme: B
When connecting the kitchen to the gas supply, you must act on the inlet.
the crossbar, without forcing the set (crossbar, connection, crossbar). The deformations
caused by operating without due care, making the warranty null and void.

The kitchen consists of a system of

couplings for connections of
aluminum.
If for some reason it needs to be changed the
tap, or disconnect the connection, to
reconnect the aluminum pipe to
faucet, or the elbow injector port,
insert it all the way in and then check
Injector that there are no gas leaks,
He/She works on moistening with a sponge and water
slippery in the encounters to control,
security observing that no occurs any
bubbling.
o-ring If you need to change any connection of
aluminum, purchase from the manufacturer or
representative, the original spare part, of
Connector pipe this way will avoid problems of
made of aluminum losses.

In the case of replacing the injectors, ensure their tightness.

return the screws to the injector port, by means of a chemical lock or thread seal.

2
Cleaning and maintenance
Clean the exterior surface with a dry cloth and remove any stains with water and
detergent.
Stainless steel parts should be dried with a soft cloth or chamois. If
there are still marks use a little hot vinegar, rinse and dry.
In the case of the burners, it is advisable to periodically clean the covers and the
bodies of the same, immersing them in soapy water and rubbing them with a
non-metallic brush or sponge.
It must be well dried before placement.

Useful tips
Always use containers with a minimum base diameter of 180mm for the
large burner and 90mm. for the small burners, in this case remember to put the
always call at minimum.
If you use the oven or the stovetop, do not allow children to get close, it will prevent
of such accidents.
If any gas leak is detected, close the shut-off valve immediately, call
qualified personnel to verify the device, all the connections and the proper
operation of the gas regulator.
Remember that 'this artifact should not be used as a heating element'.

EASY CLEAN OVEN

The interior parts of your kitchen are tiled with an "easy clean" system.
which has a special finish with very low levels of porosity, made up of
antacids, and a capacity to retain the fatty vapors that normally
they adhere to the walls, ceilings, and floors of an oven, in the same way it facilitates in a manner
consider the cleaning. Once the oven has been used, let it cool for a while not
less than 30 minutes, then clean the entire surface with a sponge and detergent
inside the oven, finish the action by wiping the surface with a clean, dry cloth
(European system).
3
Injector reference marking
For the proper identification of the injectors, they were marked.
with a series of grooves on the vertical faces, as shown in the diagram.

Chapter 2: User Instructions

Before starting this chapter, you should keep in mind that intense use and
extended operation of the device may require additional ventilation, for example
opening a window, or a more effective ventilation, or increasing the power of the
mechanical ventilation, it exists.
Any material alteration made during use, cleaning, or changing the bulb
it nullifies the warranty for proper operation.
It is important to know that the use of the device for any purpose other than the one for which it was
created causes the warranty to expire and also endangers your safety.
Instructions for lighting
To ignite the burner, turn the knob to the left to the maximum, then
Turn on, if it continues to spin the flame level will decrease to the minimum point of
consumption.

The oven is on and the stove is on.

Turn the knob a quarter turn
to the left (position flame
maximum). Press firmly until the
otp.Keepithtesame
pressed, brought a match to the
ignition port inside the
oven.
Wait 15 seconds by pressing
rmfiyl,then,relase
slowly the knob and check that
the oven was left on.
The burners have a system of
similar security but it should only
hold the press for 5
seconds.
This device will not operate for more than 15 seconds. If the burner does not
turn on, stop acting on the device, open the door of the enclosure and wait for the
less than 1 minute before any new attempt to start.
In case of accidental flameout of the burner, close the control of
Do not attempt to relight the burner for at least 1 minute.

4
 ATTENTION: before turning on the burners of the iron
always check that the stove caps are well fitted.

For models with electronic light and ignition

Allmodelswithelectronicignitionandlightintheovencomewiththeir
respective approval of the electrical certification bodies according to the
current regulations.

A.C. 220 V
turned on
Switch of
lighting of
170mm double action
+-
Oven light

Setting
Do not place adapters, to the ground
I changed the original file.
provision.
Green

950mm

Respect the dimensions

installation girls of the
electric socket.
Grounding green)
The oven ignition
must be done with IRAM 2092 - 1: 96
10mm the open door. Oven 220 W - 50 HZ / 25W

Use of electronic power button

The power switch is a dual-action type. Pressing the top part, you
Activate the ignition by pressing the bottom, the oven light turns on.
The oven lamp is 25W and 220V. The replacement of the lamp must be the
same power and size. To perform this operation, first unplug the
electric stove, then unscrew the glass cover, replace the bulb
and replace the cover, ensuring that both the cover and the lamp
make sure they are well adjusted, thenPlug the stove back in.
The power outlet must be free of obstacles (shelves, utensils, etc.).
This device is not designed for use by people with reduced abilities.
physical, sensory, mental, or children with lack of experience and knowledge, to
less than they have been supervised or instructed about the use of the device by
people responsible for security.
Children must be supervised to ensure that they do not play with the device.
If the power cord is damaged, it must be replaced by the manufacturer.
authorized technical service or similar qualified person in order to avoid danger.

5
 Request mechanical service
The user must request directly from the mechanical service department.
from ESCORIAL by phone at 4754-1122, during the hours of
Monday to Friday from 9:00 to 3:00 PM, int: 112, citing the purchase invoice date,
address
Upon being visited, a photocopy of the invoice must be handed over to the technician, this being a condition.
indispensable for the completion of the work.
In case you receive a visit from the mechanical service at your home and you do not
find it, he will leave you a card and later you will need to reiterate the order of
mechanical service, needing to pay $40 for the 2nd visit.
Whoever cancels the visit voids the warranty.

Sale of spare parts

LOCALITY TELEPHONE TRADE ADDRESS

Boedo Dick's House 4942-5651 Catamarca 1467 (CABA)

Patricios Park Jarse House 4308-1838 Manuel García 154 (CABA)
Saint Martin Agras Jorge 4752-1327 Street 95 No. 1910 (1650)
Ramos Mejia Viano House 4469-1160 Bolivar 646 (1704)
Merlo Request 0220-4827570 Guemes 2225 (1722)
Quilmes South Road 4257-4190 Av. Mitre 4301 1882
Munro The Twins 4756-3683 Velez Sarfield 4935 (1605)
The highlighted business ships nationwide.

2014

6
Chapter 3: Product Guarantee

WARRANTY CERTIFICATE
This warranty is unique and extends to the entire territory of the Republic.
Argentina.
No person is authorized to act on behalf of ESCORIAL S.A.I.C.
responsibilities or obligations related to the sale of this unit, which do not
explicitly mentioned in this guarantee.
ESCORIAL S.A.I.C. manufactures and guarantees to the original buyer, the correct
operation and performance of this kitchen for 6 months, starting from the date of
delivery of the kitchen, presenting the corresponding invoice.
This warranty does not cover defects or breakages caused by improper use,
mistreatment, blows or intervention by third parties, nor if the defect were
consequence of the poor installation of the device, the excessive gas pressure
h e l l o t r a n s f o r m a t i o n o f a g a s a n o t h e r.
In the event that the device needs to be repaired, it will be done on site.
installed, within the radius of 50km. Starting from our
establishment, for Capital and Greater Buenos Aires.
Customers residing outside the mentioned radius must proceed
by phone to the mechanical service of ESCORIALS.A.I.C., who will advise them
regarding this.
If it is not possible to repair it at the designated location, it will be sent to
our factory or the nearest authorized service, with freight costs borne by
ESCORIALS.A.I.C.
The repair will be carried out within 30 days from the date.
evident, that the request for mechanical service has been made.
The customer cannot request the replacement of the appliance for minor defects or that
they are susceptible to repair without leaving any sequelae on him.

DOES NOT COVER THE WARRANTY

1) The glass and the glazing are expressly excluded from this warranty.
If a connection approved by I.G.A. is not used.
3) If this connection is pinched by bends or rotation,
blocking the normal flow of gas.
If the instructions 'TO CONNECT' are not followed.
If connecting the kitchen alters or changes any of its components
factory originals (such as if the back of the oven is cut to
establish the connection.)
6) If the kitchen is properly installed and shows no defects
technicians when calling technical service, but does not know how to operate to
turning it on, for not reading the instruction manual.
7) In case the regulator is in poor condition, there is pressure
excessive or insufficient gas, or having a damaged connection.
8) If you change the injectors on your own (when it is not appropriate to do so)
type of gas.
If you have any broken handle.
The position of the bar changes in some way.
11) Thermocouple misaligned or broken.