STUDENT NAME :

STUDENT NUMBER :

ASSIGNMENT 2
SUBJECT: ELECTRONICS II

SUBJECT CODE: EL2F06D

DUE DATE : 14/08/2025

TIME : 13H00.
INSTRUCTIONS TO CANDIDATES:
Answer all the questions. Fill in the answers in the spaces provided on the question paper.
All answers must be given in correct units.
Answers must be accurate to the first three significant figures.
Show all the rough work on the opposite page

EXAMINER: MR T D MATSHIBA
MODERATOR: MR T C TSHIPOTA

1
QUESTION 1 (9)

The above circuit represents a multi-stage operational amplifier. Fill in the following table:

What configuration is stage D?

A
Determine the output voltage at ... B

The voltage at Q in stage B

The current at S in stage A

The current at P in stage D

In what configuration is stage B?

2
QUESTION 2 (8)

10k
B
V1
2V 5k A U1 10k
C
10k

U3
F
V2
3V U2 10k

10k
E D
1k

5k

Analyze the circuit diagram above and complete the following table.
Voltage at A: 1 Voltage at B: 1
Voltage at C: 1 Voltage at D: 1
Voltage at E: 1 Voltage at F: 1
Current at A: 1 Current at D: 1

3
QUESTION 3 (6)
For circuit below, R1 = 1500 Ω; R2 = 2200 Ω; R3 = 2700 Ω; V1 = 4 V; V2 = V3 = 18 V; pin2
is inverting input; pin3 is non-inverting input; pin6 is output.

Complete the table below, making use of circuit above:

In what configuration is the operational amplifier connected?

What is the voltage gain of the amplifier?

What are the voltages / currents at the following points in the circuit?

Voltage at point X: Current at point X:

Current at point W: Current at point Y:

4
QUESTION 4 (6)

The following circuit is built with a TL071 operational amplifier:

The supply voltages are +15V and -15V on pin 7 and 4 respectively. Vin is a sine wave with
amplitude (from zero to peak) of 0.8V at 2400 Hz.

Complete the table below:

Av:

Amplitude of Vout: Period of the wave at Vout:

RMS value of Vout: In what configuration is the operational

What is the maximum RMS value of the voltage at Vin if the output wave should remain
undistorted, assuming the output swing can reach the supply voltage?

5
QUESTION 4 (14)

10.9V A Q1 B
RMS R1
120
𝑉𝑟(𝑝𝑝) = 2𝑉 RL
C1
Z1 84
𝛽 = 50 7.2V

4.1 Analyse the regulated power supply in the circuit diagram and complete the table below.

Vp(sec)= (1) Vp at point A= (1)

VDC at A= (1) VDC at point B= (1)

IRL= (1) IB= (1)

IR1= (1) IZ= (1)

IC= (1) I at point A= (1)

P Z= (1) PQ1= (1)

4.2 If the 5.1V zener diode has a 1W power rating, what is the maximum allowable zener
current? Show calculation. (2)

6
QUESTION 5 (10)

For the circuit above, the following information is given : VAB = 20VDC; 𝛽1 = 90; R1 =
1.5kΩ ; R2 = 2.2kΩ ; R3 = 5.6kΩ ; IL = 30mA ; VZ = 8.2V/1W.
Analyse the circuit and complete table below.
VRL RL

VB IR1

IR2 IE

IB IC

VCE VR2

7
QUESTION 6 (10)

Load current through RL: 200mA

(a) The purpose of the above circuit: (1)

(b) Explain the purpose of the following components:

The purpose of the Capacitor (C1): (1)

(c) Calculate and fill in the following for the circuit given: V(RL): (1)

V(R2): (1) V(R1): (1) V(Rs): (1)

VCE(Q1): (1) VCE(Q2): (1) IE(Q1):

8
QUESTION 7 (15)

7.1 Draw a complete ac to dc power supply block diagram, name each block and adding in a
corresponding wave-form starting from the ac to dc supplying the load. (10)

7.2 Draw a complete block diagram of a series regulator with unregulated input to regulated output.(5)