Version 1.
05
(11.01.2021)
Installation instruction
Xenon Adapter
p
am
ch
on
R
50
Article no. 36752
02
36752-1
-7
R
33791
EU
40414
40415 ST
PA
E
U
N
VE
A
3
-4
ur
ko
ed
M
lim
Sa
se
en
lic
le
ng
Si
Audi A3 8P & 8P Sport
Audi TT 8J
www.kufatec.de
Kufatec GmbH • Dahlienstr. 15 • 23795 Bad Segeberg • e-mail: [email protected]
Contents
General advice..................................................................................................................................... 1
Safety instructions............................................................................................................................... 2
Notes for references of legal regulations for operation.........................................................................2
Installation instructions......................................................................................................................... 3
For vehicles before the 2008 model year (not LED technique).........................................................4
p
For vehicles from the 2008 model year–Facelift–LED technique (not for TT)...................................4
am
For vehicles from the 2010 model year–Facelift–LED technique (not for TT)...................................4
ch
Coding................................................................................................................................................. 5
on
R
50
02
-7
General advice
R
EU
While developing this product, your personal safety combined with the best operating service,
modern design and an up-to-date production technique was especially taken into account.
Unfortunately, despite the utmost care injuries and/or damages might occur due to improper
ST
PA
installation and/or use.
E
Therefore please read with great care and completely this operating manual and store it
U
appropriately!
N
VE
For your safety all our products pass through a 100% control check.
A
We reserve the right to carry out technical changes which serve the improvement at any time.
3
-4
According to each article and purpose, it is sometimes necessary to check each country’s legal
regulations before installing and starting the unit.
ur
ko
In case of guarantee claims, the device has to be sent back to the seller in the original packaging
with the attached bill of purchase and detailed defect‘s description. Please pay attention to the
ed
manufacturer‘s return requirements (RMA). The legal warranty directions are valid.
M
The warranty claims as well as the operating permissions become invalid due to:
lim
a) unauthorized changes to the device or accessories which have not been approved or
Sa
carried out by the manufacturer or its partners
se
b) opening the device‘s frame
en
c) self-made repairs on the device
lic
d) improper use / operation
le
e) brute force to the device (drop, willful damage, accident etc.)
ng
During installation, please pay attention to all safety relevant and legal directions.
Si
The device has only to be installed by trained personnel or similarly qualified people.
1
Safety instructions
The installation can be executed only by trained qualified personnel. Before the installation
disconnect the power supply. Therefore cut off the battery from the vehicle electric system, follow the
manufacturer’s specification.
• Never use bolts, screws and other fastening elements from car’s safety devices or steering
wheel, brakes because it may influence your driving safety and cause accidents.
• Connect the device only to a 12V vehicle voltage with chassis ground to the car body. This
p
unit cannot be used in large trucks or other vehicles which use a DC 24 V battery wiring system
am
voltage.
ch
• Avoid to install the device in places where it could hinder the safe driving or functional
on
efficiency of the other units installed in the vehicle.
R
• This unit is only for the use with the following vehicles and model line; Only connections
50
described within this instruction manual are allowed or required to use for installation.
02
• For damage impact caused by faulty installation, unsuitable connections or assembling in
-7
inappropriate vehicle types or models Kufatec GmbH &Co.KG assumes no liability.
• We advise you that these units process data out of the CAN protocol from the vehicle. During
R
EU
the assembly of this unit we as supplier have access to a specific model and we as producer
don’t know the overall system you work with.
ST
• Especially in case of changes within the same model line and the same model year we don’t
PA
guarantee the usability of our products. In case of the usability of our products with the
manufacturer’s changes Kufatec GmbH assumes no liability.
E
U
• Kufatec GmbH assumes no liability that the assembly of the unit described in this manual is
N
approved according the warranty regulations of the single car manufacturers. Please check
VE
your manufacturer’s conditions and warranty before you begin the installation.
A
• Kufatec GmbH reserves the right to change the device specification without further notice.
3
-4
ur
ko
Notes for references of legal regulations for operation
ed
M
Use this unit in the intended domain only.
lim
If you use the unit in a foreign domain, if the unit is not installed properly, or if the unit will be
reconstructed the operating permit and warranty will expire.
Sa
se
en
lic
le
ng
Si
2
Installation instructions
p
am
ch
on
R
1 – On-board control unit 2, 3 – Xenon head lamps left, right
50
02
-7
Assemble the Xenon head lamps. Dismantle the battery (fig.1) (vehicle depending). Lay the single
wires into the interior through the boot situated behind (fig.2).
R
EU
ST
PA
E
U
N
VE
A
Fig. 1 Fig. 2
3
-4
ur
ko
NOTE: The laying of the wires into the interior can vary depending on the model.
ed
M
lim
Loosen the screws of the bottom covering (fig. 3) and take it out (fig. 4).
Sa
se
en
lic
le
ng
Si
Fig. 3 Fig. 4 Fig. 5
3
Take the plugs A+D out of the on-board control unit (fig. 5 - 7). Actuate the pink locking and
connect the wires as follows:
p
am
ch
on
R
Fig. 6 Fig. 7
50
For vehicles before the 2008 model year (not LED technique)
02
-7
Plug D (brown) 11-pin Plug A (black) 11-pin
R
PIN 6 (Bi-Xenon) Imprint C48 PIN 5 (Bi-Xenon) Imprint C49
EU
PIN 3 (day time running lights) Imprint C26 PIN 3 (day time running lights)Imprint A44
ST
PA
For vehicles from the 2008 model year–Facelift–LED technique (not for TT)
E
U
Plug D (brown) 11-pin Plug A (black) 11-pin
N
VE
PIN 6 (Bi-Xenon) Imprint C48 PIN 5 (Bi-Xenon) Imprint C49
PIN 10 (day time running light) Imprint C26 PIN 7 (day time running light) Imprint A44
A
3
-4
ur
ko
For vehicles from the 2010 model year–Facelift–LED technique (not for TT)
ed
Plug C (beige) Plug A (black)
M
PIN 26 PIN 44
lim
PIN 48
PIN 49
Sa
se
en
lic
le
ng
Si
4
Coding
In order to carry out the coding of the vehicle choose the vehicle self-diagnostics. Execute the
coding step-by-step according to the following figures.
p
am
ch
on
R
Vehicle self-diagnostics Self-diagnostics Address 09 (central electrics)
50
02
-7
R
EU
ST
PA
E
U
N
VE
Coding Master Select BIN Enter the coding value + confirm
A
3
On-board control unit (address 09)
-4
Bi-Xenon: Byte 17 - Bit 1 deactivation (additional upper beam with Bi-Xenon)
ur
Byte 00 - Bit 3 activation (day time running light - Scandinavian active) – Front + Rear
ko
Byte 00 - Bit 4 activation (day time running light – North America active) – Only Front
ed
M
Byte 21 – Bit 5 head lamp version (Bi-Xenon with apart TFL)
lim
Sa
Bi-Xenon: Byte 17 - Bit 1 deactivation (additional upper beam with Bi-Xenon)
(LED) Byte 00 - Bit 3 activation (day time running light - Scandinavian active) – Front + Rear
se
en
Byte 00 - Bit 4 activation (day time running light – North America active) – Only Front
lic
Byte 21 – Bit 6 head lamp version (Bi-Xenon with LED for TFL)
le
ng
Si
Powered by TCPDF (www.tcpdf.org)
