FAKULTI PENDIDIKAN TEKNIKAL DAN VOKASIONAL
UNIVERSITI TUN HUSSEIN ONN MALAYSIA
86400 PARIT RAJA
BATU PAHAT JOHOR
AKTIVITI/
ACTIVITY KERTAS KERJA /WORK SHEET
NAMA PROGRAM DAN
NAMA KURSUS/ BBN10205-PRODUCT DEVELOPMENT
PROGRAM’S CODE & TECHNOLOGY
NAME
NO. DAN TAJUK UNIT
KOMPETENSI /
COMPETENCY UNIT NO.
AND TITLE
NO. DAN PENYATAAN
AKTIVITI KERJA / WORK LAB 2: OSCILLOSCOPE AND FUNCTION
ACTIVITIES NO. AND
STATEMENT GENERATOR
OBJEKTIF/
OBJECTIVES
1.
AHLI KUMPULAN/ 2.
GROUP MEMBERS 3.
ITEM MARKS
1. Attendance/Discipline
/ 10
2. Participation
UNTUK KEGUNAAN / 10
PENGAJAR SAHAJA/
3. Results
FOR INSTRUCTORS / 50
ONLY
4. Discussion
/ 20
5. Conclusion
/ 10
TOTAL MARKS / 100
Instructor’s Comment Submission Stamp and Date
1
TITLE : OSCILLOSCOPE
OBJECTIVES : At the end of this experiment, students should be
able to
i) Know the functions of oscilloscope .
ii) Use the oscilloscope.
EQUIPMENT LIST : i) Oscilloscope Tektronix model TDS 1002 or TDS 1012
ii) Instruction Manual
THEORY:
Oscilloscope is an electronic device which display the electrical signal such as
wave or pulse. The most commonly used in the laboratory are model TDS 1002 or
TDS 1012. Figure 1.1 and 1.2 show the oscilloscope Tektronix model TDS 1002 or
TDS 1012 respectively.
Figure 1.1: Oscilloscope model TDS 1002
Figure 1.2: Oscilloscope model TDS 1012
2
EQUIPMENT PANEL CONTROL
Refer to the User Manual and complete Table 1.1 to identify the certain sections of front
panel control and their functions of oscilloscope model TDS 1002 or TDS 1012.
1 2 3 4 5 6 7 8 9 10 11 12
13
14
15
16
17
18
19
20
21 22 23 24 25 26 27 28
Figure 1.3
Section
Name Function
Number
1
3
7
4
8
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Table 1.1
5
MEASUREMENT VOLTAGE PEAK TO PEAK (VPP)
3 Divisions
Wave A
VOLT/DIV = 100 mv
5 Divis ions
TIME/DIV = 1 ms
Wave B
ions
4 Divis
6 Divisions
Figure 1.4
Figure 1.4 is shown two sine wave with amplitude and different duration. Wave A form has
form wave peak to peak 5 vertical divisions. Wave B measured as 4 divisions peak to peak vertical
VOLT/DIV set by 100 mV.
Peak to peak voltage,Vpp (V) = Sum of peak to peak division x VOLT/DIV (1.1)
Root mean Square Voltage,Vrms (V) = 1 Vp or 0.7071 Vp (1.2)
2
Wave A,
V = 5 division x 100 mv = 1000 mv / 1000 div = 0.5v
V= 0.7071 x 2.5Vp = 1.76775v
Wave B,
V = 4 division x 100mv = 1000 mv / 1000 div = 0.4v
V = 0.7071 x 2Vp = 1.4142v
6
FREQUENCY DETERMINATION
Time duration,T and frequency, F can be calculated by the equation 1.3 and 1.4 respectively.
Period, T (s) = Sum of horizontal division/cycle x TIME/DIV (1.3)
1
Frequency, F (Hz) =
T (1.4)
Wave A,
T = ………………………………
f = ………………………………
Wave B,
T = …………………………………
f = ………………………………...
EXERCISE
1. VOLT/DIV = 10 mV, TIME/DIV = 2 ms. Based on waveforms in Figure 1.5 below, calculate
and complete Table 1.2:
i) Peak to peak voltage, Vpp
ii) Time duration, T
iii) Frequency, f
3 divisions
Wave A
4 divisions
Figure 1.5
Wave B
3 divisions
8 divisions
7
i) peak to peak voltage (V) ii) Time duration (s) iii) Frequency (Hz)
Table 1.2
2. VOLT/DIV = 10 mV, TIME/DIV = 4 ms. Based on waveforms in Figure 1.6 below, calculate
and complete Table 1.3 :
i) Peak to peak voltage, Vpp
ii) Time duration, T
iii) Frequency, f
4 divisions
Wave A
4 divisions
Figure 1.6
Wave B
2 s
division
8 divisions
i) peak to peak voltage (V) ii) Time duration (s) iii) Frequency (Hz)
Table 1.3
8
TITTLE : Function Generator
OBJECTIVES : At the end of this work sheet, student should be able to
i) Know the function of function generator.
ii) Use the function generator.
EQUIPMENT LIST : i) Topward 8150 Function Generator 10MHz
ii) Instruction Manual
THEORY :
A function generator is an electronic equipment which is to generate electrical waveforms
as shown in Figure 1.7.
Figure 1.7: Topward 8150 Function Generator 10MHz
The most common waveform is a sine wave, square wave, triangular wave and sawtooth as
shown in Figure 1.8.
9
Figure 1.8 : Function Generator Output Waveform
An oscilloscope is then used to measure the output waveform of the function generators
using BNC connector as shown in Figure 1.9.
Figure 1.9 Male 50 Ω BNC connector
EQUIPMENT PANEL CONTROL
The front panel controls as shown in Figure 1.10 are functionally grouped and clearly
designated for ease of operation.
Refer to the instruction manual and complete Table 1.4 to identify the certain sections of
front panel control and their function.
1 2 3 4 5
12 11 10 9 8 7 6
Figure 1.10: Front Panel Control
10
SECTION SECTION
FUNCTION
NUMBER NAME
1
10
11
12
Table 1.4 Panel Control Section
11
EXPERIMENT : 01
TITLE : Oscilloscope And Function Generator
OBJECTIVES : At the end of this experiment, students should be able to
i) Give information about general construction of
oscilloscope.
ii) Give knowledge about functions of oscilloscope.
iii) Learn how to calculate voltage peak to peak
(Vpp) and frequency.
EQUIPMENT LIST : i) Oscilloscope Tektronix model TDS 1002 or TDS 1012
ii) Function Generator model 8150
THEORY :
INTRODUCTION TO OSCILLOSCOPE
Oscilloscope is an electronic device which display the electrical signal such as wave or
pulse. It can be used to measure voltage, frequency, time and so on. The model TDS 1002 is a
small light weight and easy to use. It is a multipurpose Dual Oscilloscope with 6 inch and 2KV CRT.
It is a unique built-in component tester that allows testing of passive and active components such
as FETs, bipolars, zeners, capacitors or inductors by observing test waveforms on the CRT.
PROBE ADJUSTMENT
When applying the external signal, a probe is used to measure waveform as shown in Figure 1.8.
The applied waveform is displayed on the CRT of oscilloscope. The product has two points : there
are x 1 (direct connection) and x 10 (attenuation).
A x10 probe is used for high frequency measurement because of the reduction of input
capacity which distorts signal and reduces the load. Using any incorrectly calibrated probe may
cause error in the measurement.
12
PROCEDURES A:
Calibration.
1. Set the Probe obtion attenuation in the channel menu x 10. Set the switch to x10 on the
P2200 probe and connect the probe to channel oscilloscope.
2. Attach the probe tip top to the PROBE COMP - 5V connector and the reference lead to
the PROBE COMP Ground connector. Display the channel and the push the AUTOSET
button.
3. A square waveform (5 Vpp and 1 kHz) should be displayed.
4. Push the CH1 button and set the item below:
- Coupling - AC
- Probe - x10
5. Check the shape of the displayed waveform. If necessary, adjust the probe and repeat as
necessary.
6. Sketch the waveform in Table 1.5.
7. Calculate the voltage, period and frequency of the waveform.
RESULTS:
Waveform Voltage (V) Period (s) Frequency (Hz)
1
1 2 f=
Div = Div = T
0.5 0.5 = 1
Volt/Div = Time/Div = m
Vpp = 0.5 T= 1
V ms 1
f=
kHz
Table 1.5
13
PROCEDURES B:
Measuring the Period(T) and Frequency(Hz)
BNC to
Crocodile clip
OUTPUT CH 1 CH2
Oscilloscop
Function
Generator Oscilloscope
probe
Figure 1.11 : Connection
1. Connect the output of function generator to the CH 1 oscilloscope input using BNC to BNC
cable as shown in Figure 1.11.
2. Switch on the function generator and the oscilloscope.
3. Select the FUNCTION switch to choose sine wave as an output waveform.
4. Press FREQUENCY RANGE switch to select 10 kHz frequency range output.
5. Set output frequency of 1 kHz using the FREQUENCY COARSE and FINE controls.
6. Adjust the TIME/DIV on the oscilloscope and observe the sine wave output from the
oscilloscope.
Measuring the Amplitude (Voltage peak to peak).
7. Set the amplitude 3 Vpp using the AMPLITUDE on the function generator and VOLT/DIV on
the oscilloscope.
8. Observe the sine wave output from the oscilloscope.
9. Sketch the output waveform 1 kHz, 3 Vpp in Table 1.6.
10. Repeat procedure 5 to 10 for different voltages and frequencies as shown in Table 1.6.
14
No. Waveform Vpp (V) Period (s) Frequency (Hz)
1. 1 kHz, 3 Vpp
2. 15 kHz, 3 Vpp
3. 5 Vpp, 10 kHz
4. 10 Vpp, 10 kHz
Table 1.6
DISCUSSION:
When you change the voltage (Vpp) value or the frequency value, compare the signal difference. Give
the reason.
CONCLUSION:
REFERENCES:
15
