TRANSLATIONS

Lot or Batch Size Batch size

Special Inspection Levels Special Inspection Levels
General Inspection Levels General inspection levels
Single Simple
Double Double
Multiple Multiple
Normal Normal
Tightened Rigorous
Reduced Reduced
Acceptable Quality Level Acceptable quality levels
Sample Size Sample size
Code Letters Letter code
Use the sampling plan
arrow. If sample size equals or immediately less than the arrow. If the
exceeds lot or batch size, do 100 sample size is equal to or
percent inspections superior to the batch, to do
100% inspection
Use the sampling plan above
arrow immediate above the arrow
Acceptance Number Acceptance number
Rejection Number Rejection number
Use corresponding single sampling
plan (or alternatively, use double simple corresponding (Or well,
sampling plan below, where possible, the plan of
available) lower double sampling
If, after the second sample
acceptance number has been exceeded
exceeded, but the rejection but without reaching the rejection, it
number has not been reached, accept the batch but it is reinstated
accept the lot, but reinstate normal inspection.
normal inspection
Use corresponding double employ the double sampling plan
sampling plan (or alternatively, corresponding (Or well, when
use the double sampling plan below, if possible, the sampling plan
where available lower double
Acceptance not permitted at this
sample size this sample size
 MIL-STD-105E Page 17 of 74

TABLE I– Sample Size code letters

(See 4.9.1 and 4.9.2)

Special inspection levels General inspection levels

Lot or batch size
S-1 S-2 S-3 S-4 I II III
2 To 8 A A A A A A B
9 To 15 A A A A A B C
16 To 25 A A B B B C D
26 To 50 A B B C C D E
51 To 90 B B C D D F G
91 To 150 B B C D D F G
151 To 280 B C D E E G H
281 To 500 B C D E F H J
501 To 1200 C C E F G J H
1201 To 3200 C D E G H K L
3201 To 10000 C D F G J L M
10001 To 35000 C D F H K M N
35001 To 150000 D E G J L N P
150001 To 500000 D E G J M P Q
500000 And Over D E H K N Q R

CODE LETTERS
 MIL-STD-105E

TABLE II-A – Single sampling plans for normal inspection (Master table)
See 4.9.3. and 4.9.4)
Acceptable Quality Levels (Normal Inspection)
Sample 0.010 0.015 0.025 0.040 0.065 0.10 0.15 0.25 0.40 0.65 1.0 1.5 2.5 4.0 6.5 10 15 25 40 65 100 150 250 400 650 1000
size Sample
Code size
Letters
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re

A 2 0 1 1 2 2 3 3 4 5 6 7 8 10 11 14 15 21 22 30 31
B 3 0 1 1 2 2 3 3 4 5 6 7 8 10 11 14 15 21 22 30 31 44 65
C 5 0 1 1 2 2 3 3 4 5 6 7 8 10 11 14 15 21 22 30 31 44 65
D 8 0 1 1 2 2 3 3 4 5 6 7 8 10 11 14 15 21 22 30 31 44 65
E 13 0 1 1 2 2 3 3 4 5 6 7 8 10 11 14 15 21 22 30 31 44 65
F 20 0 1 1 2 2 3 3 4 5 6 7 8 10 11 14 15 21 22
G 32 0 1 1 2 2 3 3 4 5 6 7 8 10 11 14 15 21 22
H 50 0 1 1 2 2 3 3 4 5 6 7 8 10 11 14 15 21 22
J 80 0 1 1 2 2 3 3 4 5 6 7 8 10 11 14 15 21 22
K 125 0 1 1 2 2 3 3 4 5 6 7 8 10 11 14 15 21 22
L 200 0 1 1 2 2 3 3 4 5 6 7 8 10 11 14 15 21 22
M 315 0 1 1 2 2 3 3 4 5 6 7 8 10 11 14 15 21 22
N 500 0 1 1 2 2 3 3 4 5 6 7 8 10 11 14 15 21 22
P 800 0 1 1 2 2 3 3 4 5 6 7 8 10 11 14 15 21 22
Q 1250 0 1 1 2 2 3 3 4 5 6 7 8 10 11 14 15 21 22

R 2000 1 2 2 3 3 4 5 6 7 8 10 11 14 15 21 22

= Use the first sampling plan below the arrow. If the sample size equals or exceeds the lot or batch size, conduct 100 percent inspections.
= Use the first sampling plan above the arrow.
Ac = Acceptance number
Re = Rejection number
SINGLE
NORMAL
 MIL-STD-105E Page 19 of 74
TABLE II-B– Single sampling plans for tightened inspection (Master table)
(See 4.9.3. and 4.9.4)
Acceptable Quality Levels (Normal Inspection)
Sample 0.010 0.015 0.025 0.040 0.065 0.10 0.15 0.25 0.40 0.65 1.0 1.5 2.5 4.0 6.5 10 15 25 40 65 100 150 250 400 650 1000
size Sample
Code size
Letters
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re

A 2 1 2 2 3 3 4 5 6 8 9 12 13 18 19 27 28
B 3 0 1 1 2 2 3 3 4 5 6 8 9 12 13 18 19 27 28 41 42
C 5 0 1 1 2 2 3 3 4 5 6 8 9 12 13 18 19 27 28 41 42
D 8 0 1 1 2 2 3 3 4 5 6 8 9 12 13 18 19 27 28 41 42
E 13 0 1 1 2 2 3 3 4 5 6 8 9 12 13 18 19 27 28 41 42
F 20 0 1 1 2 2 3 3 4 5 6 8 9 12 13 18 19
G 32 0 1 1 2 2 3 3 4 5 6 8 9 12 13 18 19
H 50 0 1 1 2 2 3 3 4 5 6 8 9 12 13 18 19
J 80 0 1 1 2 2 3 3 4 5 6 8 9 12 13 18 19
K 125 0 1 1 2 2 3 3 4 5 6 8 9 12 13 18 19
L 200 0 1 1 2 2 3 3 4 5 6 8 9 12 13 18 19
M 315 0 1 1 2 2 3 3 4 5 6 8 9 12 13 18 19
N 500 0 1 1 2 2 3 3 4 5 6 8 9 12 13 18 19
P 800 0 1 1 2 2 3 3 4 5 6 8 9 12 13 18 19
Q 1250 0 1 1 2 2 3 3 4 5 6 8 9 12 13 18 19
0 1
R 2000 01 1 2 2 3 3 4 5 6 8 9 12 13 18 19
S 3150 1 2
= Use the first sampling plan below the arrow. If the sample size equals or exceeds the lot or batch size, perform 100 percent inspections.
= Use the first sampling plan above the arrow.
Ac = Acceptance number
Regarding
= Rejection number
SINGLE
TIGHTENED
 MIL-STD-105E Page 20 of 74
TABLE II-C– Single sampling plans for reduced inspection (Master table)
See 4.9.3. and 4.9.4)
Acceptable Quality Levels (Reduced Inspection)
Sample 0.010 0.015 0.025 0.040 0.065 0.10 0.15 0.25 0.40 0.65 1.0 1.5 2.5 4.0 6.5 10 15 25 40 65 100 150 250 400 650 1000
size Sample
Code size
Letters
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re

A 2 0 1 1 2 2 3 3 4 5 6 7 8 10 11 14 15 21 22 30 31
B 2 0 1 0 2 1 3 2 4 3 5 5 6 7 8 10 11 14 15 21 22 30 31
C 2 0 1 0 2 1 3 1 4 2 5 3 6 5 8 7 10 10 13 14 17 21 24
D 3 0 1 0 2 1 3 1 4 2 5 3 6 5 8 7 10 10 13 14 17 21 24
E 5 0 1 0 2 1 3 1 4 2 5 3 6 5 8 7 10 10 13 14 17 21 24
F 8 0 1 0 2 1 3 1 4 2 5 3 6 5 8 7 10 10 13
G 13 0 1 0 2 1 3 1 4 2 5 3 6 5 8 7 10 10 13
H 20 0 1 0 2 1 3 1 4 2 5 3 6 5 8 7 10 10 13
J 32 0 1 0 2 1 3 1 4 2 5 3 6 5 8 7 10 10 13
K 50 0 1 0 2 1 3 1 4 2 5 3 6 5 8 7 10 10 13
L 80 0 1 0 2 1 3 1 4 2 5 3 6 5 8 7 10 10 13
M 125 0 1 0 2 1 3 1 4 2 5 3 6 5 8 7 10 10 13
N 200 0 1 0 2 1 3 1 4 2 5 3 6 5 8 7 10 10 13
P 315 0 1 0 2 1 3 1 4 2 5 3 6 5 8 7 10 10 13
Q 500 0 1 0 2 1 3 1 4 2 5 3 6 5 8 7 10 10 13

R 800 0 2 1 3 1 4 2 5 3 6 5 8 7 10 10 13

= Use the first sampling plan below the arrow. If the sample size equals or exceeds the lot or batch size, perform 100 percent inspections.
= Use the first sampling plan above the arrow.
Ac = Acceptance number
Re = Rejection number
= Use corresponding single sampling plan (or alternatively, use double sampling plan below, where available)
† = If, after the second sample, the acceptance number has been exceeded, but the rejection number has not been reached, accept the lot, but reinstate normal inspection (see [Link])
SINGLE
REDUCED
 MIL-STD-105E Page 21 of 74
TABLE III-A– Double sampling plans for normal inspection (Master table)
See 4.9.3. and 4.9.4)
Acceptable Quality Levels (Normal Inspection)

0.010 0.015 0.025 0.040 0.065 0.10 0.15 0.25 0.40 0.65 1.0 1.5 2.5 4.0 6.5 10 15 25 40 65 100 150 250 400 650 1000

Ac Re Ac Re This Go ahead About Re As it is As it is Ac Re Ac Re Ac Re Leave me To the thing As it is Regarding Ac Re Ac Re Ac Re As it is Ac Re As Re As it is As it is With regard toAbout Re As It Is It is

First 2 2 0 2 0 3 1 4 2 5 3 7 5 9 7 11 11 16 17 22 25 31
B 1 2 3 4 4 5 6 7 8 9 12 13 18 19 26 27 37 38 56 57
Second 2 4
First 3 3 0 2 0 3 1 4 2 5 3 7 5 9 7 11 11 16 17 22 25 31
C 1 2 3 4 4 5 6 7 8 9 12 13 18 19 26 27 37 38 56 57
Second 3 6
First 5 5 0 2 0 3 1 4 2 5 3 7 5 9 7 11 11 16 17 22 25 31
D 1 2 3 4 4 5 6 7 8 9 12 13 18 19 26 27 37 38 56 57
Second 5 10
First 8 8 0 2 0 3 1 4 2 5 3 7 5 9 7 11 11 16 17 22 25 31
E 1 2 3 4 4 5 6 7 8 9 12 13 18 19 26 27 37 38 56 57
Second 8 16
First 13 13 0 2 0 3 1 4 2 5 3 7 5 9 7 11 11 16
F 1 2 3 4 4 5 6 7 8 9 12 13 18 19 26 27
Second 13 26
First 20 20 0 2 0 3 1 4 2 5 3 7 5 9 7 11 11 16
G 1 2 3 4 4 5 6 7 8 9 12 13 18 19 26 27
Second 20 40
First 32 32 0 2 0 3 1 4 2 5 3 7 5 9 7 11 11 16
H 1 2 3 4 4 5 6 7 8 9 12 13 18 19 26 27
Second 32 64
First 50 50 0 2 0 3 1 4 2 5 3 7 5 9 7 11 11 16
J 1 2 3 4 4 5 6 7 8 9 12 13 18 19 26 27
Second 50 100
First 80 80 0 2 0 3 1 4 2 5 3 7 5 9 7 11 11 16
K 1 2 3 4 4 5 6 7 8 9 12 13 18 19 26 27
Second 80 160
First 125 125 0 2 0 3 1 4 2 5 3 7 5 9 7 11 11 16
L 1 2 3 4 4 5 6 7 8 9 12 13 18 19 26 27
Second 125 250
First 200 200 0 2 0 3 1 4 2 5 3 7 5 9 7 11 11 16
M 1 2 3 4 4 5 6 7 8 9 12 13 18 19 26 27
Second 200 400
First 315 315 0 2 0 3 1 4 2 5 3 7 5 9 7 11 11 16
N 1 2 3 4 4 5 6 7 8 9 12 13 18 19 26 27
Second 315 630
First 500 500 0 2 0 3 1 4 2 5 3 7 5 9 7 11 11 16
P 1 2 3 4 4 5 6 7 8 9 12 13 18 19 26 27
Second 500 1000
First 800 800 0 2 0 3 1 4 2 5 3 7 5 9 7 11 11 16
Q 1 2 3 4 4 5 6 7 8 9 12 13 18 19 26 27
Second 800 1600
First 1250 1250 0 2 0 3 1 4 2 5 3 7 5 9 7 11 11 16
R
Second 1250 2500 1 2 3 4 4 5 6 7 8 9 12 13 18 19 26 27
= Use the first sampling plan below the arrow. If the sample size equals or exceeds the lot or batch size, conduct 100 percent inspections.
= Use the first sampling plan above the arrow.
Ac = Acceptance number
Re = Rejection number
= Use corresponding single sampling plan (or alternatively, use double sampling plan below, where available)
DOUBLE
NORMAL
 MIL-STD-105E Page 22 of 74
TABLE III-B– Double sampling plans for tightened inspection (Master table)
See 4.9.3. and 4.9.4)
Acceptable Quality Levels (Tightened Inspection)†
0.010 0.015 0.025 0.040 0.065 0.10 0.15 0.25 0.40 0.65 1.0 1.5 2.5 4.0 6.5 10 15 25 40 65 100 150 250 400 650 1000

Regarding From here In fact As it is About Re Ac Re Ac Re Ac Re Thank you The Field Ac Re It is Re Ac Re Hi It is Ac Re Ac Re Ac Re Ac Re On the way As it is About Re Ac Re This is Ac Re As It Is

A
First 2 2 0 2 0 3 1 4 2 5 3 7 6 10 9 14 15 20 23 29
B
Second 2 4 1 2 3 4 4 5 6 7 11 12 15 16 23 24 31 33 34 35
First 3 3 0 2 0 3 1 4 2 5 3 7 6 10 9 14 15 20 23 29
C 1 2 3 4 4 5 6 7 11 12 15 16 23 24 31 33 34 35
Second 3 6
First 5 5 0 2 0 3 1 4 2 5 3 7 6 10 9 14 15 20 23 29
D 1 2 3 4 4 5 6 7 11 12 15 16 23 24 31 33 34 35
Second 5 10
First 8 8 0 2 0 3 1 4 2 5 3 7 6 10 9 14 15 20 23 29
E one2 3 4 4 5 6 7 11 12 15 16 23 24 31 33 34 35
Second 8 16
First 13 13 0 2 0 3 1 4 2 5 3 7 6 10 9 14
F 1 2 3 4 4 5 6 7 11 12 15 16 23 24
Second 13 26
First 20 20 0 2 0 3 1 4 2 5 3 7 6 10 9 14
G 1 2 3 4 4 5 6 7 11 12 15 16 23 24
Second 20 40
First 32 32 0 2 0 3 1 4 2 5 3 7 6 10 9 14
H 1 2 3 4 4 5 6 7 11 12 15 16 23 24
Second 32 64
First 50 50 0 2 0 3 1 4 2 5 3 7 6 10 9 14
J 1 2 3 4 4 5 6 7 11 12 15 16 23 24
Second 50 100
First 80 80 0 2 0 3 1 4 2 5 3 7 6 10 9 14
K 1 2 3 4 4 5 6 7 11 12 15 16 23 24
Second 80 160
First 125 125 0 2 0 3 1 4 2 5 3 7 6 10 9 14
L 1 2 3 4 4 5 6 7 11 12 15 16 23 24
Second 125 250
First 200 200 0 2 0 3 1 4 2 5 3 7 6 10 9 14
M 1 2 3 4 4 5 6 7 11 12 15 16 23 24
Second 200 400
First 315 315 0 2 0 3 1 4 2 5 3 7 6 10 9 14
N 1 2 3 4 4 5 6 7 11 12 15 16 23 24
Second 315 630
First 500 500 0 2 0 3 1 4 2 5 3 7 6 10 9 14
P 1 2 3 4 4 5 6 7 11 12 15 16 23 24
Second 500 1000
First 800 800 0 2 0 3 1 4 2 5 3 7 6 10 9 14
Q 1 2 3 4 4 5 6 7 11 12 15 16 23 24
Second 800 1600
First 1250 1250 0 2 0 3 1 4 2 5 3 7 6 10 9 14
R
Second 1250 2500 1 2 3 4 4 5 6 7 11 12 15 16 23 24
First 2000 2000 0 2
S
Second 2000 4000 1 2
= Use first sampling plan below arrow. If sample size equals or exceeds lot or batch size, perform 100 percent inspections.
= Use the first sampling plan above the arrow.
Ac = Acceptance number
Re = Rejection number
= Use the corresponding single sampling plan (or alternatively, use the double sampling plan below, where available)
DOUBLE
TIGHTENED
 MIL-STD-105E Page 23 of 74
TABLE III-C– Double sampling plans for reduced inspection (Master table)
See 4.9.3. and 4.9.4)
Acceptable Quality Levels (Reduced Inspection)
0.010 0.015 0.025 0.040 0.065 0.10 0.15 0.25 0.40 0.65 1.0 1.5 2.5 4.0 6.5 10 15 25 40 65 100 150 250 400 650 1000

Ac Re As it is Ac Re As it is Water as it is As Re Ac Re Ac Re As It Is Ac Re Oh Yes Regarding As it is Ac Re About Re About the matter As

Make It Re This is a resource it is Ac Re Oh God Ac Re
Regarding the matter Ac Re Come Here

A
B
C

First 2 2 0 2 0 3 0 4 0 4 1 5 2 7 3 8 5 10 7 12 11 17
D 0 2 0 4 1 5 3 6 4 7 6 9 8 12 12 16 18 22 26 30
Second 2 4
First 3 3 0 2 0 3 0 4 0 4 1 5 2 7 3 8 5 10 7 12 11 17
E 0 2 0 4 1 5 3 6 4 7 6 9 8 12 12 16 18 22 26 30
Second 3 6
First 5 5 0 2 0 3 0 4 0 4 1 5 2 7 3 8 5 10
F 0 2 0 4 1 5 3 6 4 7 6 9 8 12 12 16
Second 5 10
First 8 8 0 2 0 3 0 4 0 4 1 5 2 7 3 8 5 10
G 0 2 0 4 1 5 3 6 4 7 6 9 8 12 12 16
Second 8 16
First 13 13 0 2 0 3 0 4 0 4 1 5 2 7 3 8 5 10
H 0 2 0 4 1 5 3 6 4 7 6 9 8 12 12 16
Second 13 26
First 20 20 0 2 0 3 0 4 0 4 1 5 2 7 3 8 5 10
J 0 2 0 4 1 5 3 6 4 7 6 9 8 12 12 16
Second 20 40
First 32 32 0 2 0 3 0 4 0 4 1 5 2 7 3 8 5 10
K 0 2 0 4 1 5 3 6 4 7 6 9 8 12 12 16
Second 32 64
First 50 50 0 2 0 3 0 4 0 4 1 5 2 7 3 8 5 10
L 0 2 0 4 1 5 3 6 4 7 6 9 8 12 12 16
Second 50 100
First 80 80 0 2 0 3 0 4 0 4 1 5 2 7 3 8 5 10
M 0 2 0 4 1 5 3 6 4 7 6 9 8 12 12 16
Second 80 160
First 125 125 0 2 0 3 0 4 0 4 1 5 2 7 3 8 5 10
N 0 2 0 4 1 5 3 6 4 7 6 9 8 12 12 16
Second 125 250
First 200 200 0 2 0 3 0 4 0 4 1 5 2 7 3 8 5 10
P 0 2 0 4 1 5 3 6 4 7 6 9 8 12 12 16
Second 200 400
First 315 315 0 2 0 3 0 4 0 4 1 5 2 7 3 8 5 10
Q 0 2 0 4 1 5 3 6 4 7 6 9 8 12 12 16
Second 315 630
First 500 500 0 2 0 3 0 4 0 4 1 5 2 7 3 8 5 10
R
Second 500 1000 0 2 0 4 1 5 3 6 4 7 6 9 8 12 12 16
= Use the first sampling plan below the arrow. If the sample size equals or exceeds the lot or batch size, perform 100 percent inspections.
= Use the first sampling plan above the arrow.
Ac = Acceptance number
Re = Rejection number
= Use the corresponding single sampling plan (or alternatively, use the double sampling plan below, where available)
† = If, after the second sample, the acceptance number has been exceeded, but the rejection number has not been reached, accept the lot, but reinstate normal inspection (see [Link])
DOUBLE
REDUCED
 MIL-STD-105E Page 24 of 74
TABLE IV-A– Multiple sampling plans for normal inspection (Master table)
See 4.9.3. and 4.9.4)
Acceptable Quality Levels (Normal Inspection)†
0.010 0.015 0.025 0.040 0.065 0.10 0.15 0.25 0.40 0.65 1.0 1.5 2.5 4.0 6.5 10 15 25 40 65 100 150 250 400 650 1000

Ac Re As It Is Ac Re AC Re Ac Re Oh Yes As is Oh, really Ac Re As It Is About Re Ac Re About Re What it is As Re Ac Re As It Is About Re Ac Re Ac Re Oh Yes Ac Re Ac Re It has been Ac Re Ac Re

A
B ‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡
C
‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡
First 2 2 ∞2 ∞2 ∞3 ∞4 0 4 0 5 1 7 2 9 4 12 6 16
Second 2 4 ∞2 0 3 0 3 1 5 1 6 3 8 4 10 7 14 11 19 17 27
Third 2 6 0 2 0 3 1 4 2 6 3 8 6 10 8 13 13 19 19 27 29 39
D Fourth 2 8 0 3 1 4 2 5 3 7 5 10 8 13 12 17 19 25 27 34 40 49
Fifth 2 10 1 3 2 4 3 6 5 8 7 11 11 15 17 20 25 29 36 40 53 58
Sixth 2 12 1 3 3 5 4 6 7 9 10 12 14 17 21 23 31 33 45 47 65 68
Seventh 2 14 2 3 4 5 6 7 9 10 13 14 18 19 25 26 37 38 53 54 77 78
First 3 3 ∞2 ∞2 ∞3 infinity 4 0 4 0 5 1 7 2 9 4 12 6 16
Second 3 6 ∞2 0 3 0 3 1 5 1 6 3 8 4 10 7 14 11 19 17 27
Third 3 9 0 2 0 3 1 4 2 6 3 8 6 10 8 13 13 19 19 27 29 39
E Fourth 3 12 0 3 1 4 2 5 3 7 5 10 8 13 12 17 19 25 27 34 40 49
Fifth 3 15 1 3 2 4 3 6 5 8 7 11 11 15 17 20 25 29 36 40 53 58
Sixth 3 18 1 3 3 5 4 6 7 9 10 12 14 17 21 23 31 33 45 47 65 68
Seventh 3 21 2 3 4 5 6 7 9 10 13 14 18 19 25 26 37 38 53 54 77 78
First 5 5 ∞2 ∞2 ∞3 infinity 4 0 4 0 5 1 7 2 9
Second 5 10 ∞2 0 3 0 3 1 5 1 6 3 8 4 10 7 14
Third 5 15 0 2 0 3 1 4 2 6 3 8 6 10 8 13 13 19
F Fourth 5 20 0 3 1 4 2 5 3 7 5 10 8 13 12 17 19 25
Fifth 5 25 1 3 2 4 3 6 5 8 7 11 11 15 17 20 25 29
Sixth 5 30 1 3 3 5 4 6 7 9 10 12 14 17 21 23 31 33
Seventh 5 35 2 3 4 5 6 7 9 10 13 14 18 19 25 26 37 38
First 8 8 ∞2 ∞2 ∞3 ∞4 0 4 0 5 1 7 2 9
Second 8 16 ∞2 0 3 0 3 1 5 1 6 3 8 4 10 7 14
Third 8 24 0 2 0 3 1 4 2 6 3 8 6 10 8 13 13 19
G Fourth 8 32 0 3 1 4 2 5 3 7 5 10 8 13 12 17 19 25
Fifth 8 40 1 3 2 4 3 6 5 8 7 11 11 15 17 20 25 29
Sixth 8 48 1 3 3 5 4 6 7 9 10 12 14 17 21 23 31 33
Seventh 8 56 2 3 4 5 6 7 9 10 13 14 18 19 25 26 37 38
First 13 13 Infinite two infinity ∞3
squared ∞4 0 4 0 5 1 7 2 9
Second 13 26 ∞2 0 3 0 3 1 5 1 6 3 8 4 10 7 14
Third 13 39 0 2 0 3 1 4 2 6 3 8 6 10 8 13 13 19
H Fourth 13 52 0 3 1 4 2 5 3 7 5 10 8 13 12 17 19 25
Fifth 13 65 1 3 2 4 3 6 5 8 7 11 11 15 17 20 25 29
Sixth 13 78 1 3 3 5 4 6 7 9 10 12 14 17 21 23 31 33
Seventh 13 91 2 3 4 5 6 7 9 10 13 14 18 19 25 26 37 38
First 20 20 infinity ∞2
squared ∞3 infinity 4 0 4 0 5 1 7 2 9
Second 20 40 ∞2 0 3 0 3 1 5 1 6 3 8 4 10 7 14
Third 20 60 0 2 0 3 1 4 2 6 3 8 6 10 8 13 13 19
J Fourth 20 80 0 3 1 4 2 5 3 7 5 10 8 13 12 17 19 25
Fifth 20 100 1 3 2 4 3 6 5 8 7 11 11 15 17 20 25 29
Sixth 20 120 1 3 3 5 4 6 7 9 10 12 14 17 21 23 31 33
Seventh 20 140 2 3 4 5 6 7 9 10 13 14 18 19 25 26 37 38
= Use the first sampling plan below the arrow. If the sample size is equal to or exceeds the lot or batch size, perform 100 percent inspections.
= Use the first sampling plan above the arrow.
Ac = Acceptance number
Re = Rejection number
= Use the corresponding single sampling plan (or alternatively, use the double sampling plan below, where available)
‡ = Use corresponding double sampling plan (or alternatively, use double sampling plan below, where available)
MULTIPLE
∞ = Acceptance not permitted at this sample size. NORMAL
 MIL-STD-105E Page 25 of 74
TABLE IV-A– Multiple sampling plans for normal inspection (Master table)
(Continued) See 4.9.3. and 4.9.4)
Acceptable Quality Levels (Normal Inspection)
0.01 0.06
0.010 0.025 0.040 0.10 0.15 0.25 0.40 0.65 1.0 1.5 2.5 4.0 6.5 10 15 25 40 65 100 150 250 400 650 1000
5 5

Ac Re Here it is What is it Ac Re Regarding Ac Re Oh well As It Is Ac Re Here it is About Re Ac Re Ac Re I am Ac Re As it is As it is Oh Yes About Re Regarding Ac Re Acre Here's to you Ac Re Regarding About Re

∞2 ∞2 ∞3 ∞4 0 4 0 5 1 7 0 2
First 32 32
1 6 3 8 4 10 7 14
Second 32 62 ∞2 0 3 0 3 1 5
3 8 6 10 8 13 13 19
Third 32 0 2 0 3 1 4 2 6
K Fourth 32 128 1 4 2 5 3 7 5 10 8 13 12 17 19 25
0 3 7 11 11 15 17 20 25 29
Fifth 32 160 1 3 2 4 3 6 5 8
Sixth 32 192 3 5 4 6 7 9 10 12 14 17 21 23 31 33
1 3 13 14 18 19 25 26 37 38
Seventh 32 224 2 3 4 5 6 7 9 10
First 50 50 ∞2 ∞2 ∞3 ∞4 0 4 0 5 1 7 0 2
50 100 1 6 3 8 4 10 7 14
Second ∞2 0 3 0 3 1 5
3 8 6 10 8 13 13 19
Third 50 150 0 3 1 4 2 6
0 2 5 10 8 13 12 17 19 25
L Fourth 50 200 1 4 2 5 3 7
0 3 7 11 11 15 17 20 25 29
Fifth 50 250 2 4 3 6 5 8
1 3 10 12 14 17 21 23 31 33
Sixth 50 300 3 5 4 6 7 9
50 350 1 3 13 14 18 19 25 26 37 38
Seventh 2 2 3 4 5 6 7 9 10
First 80 80 ∞2 ∞2 ∞3 ∞4 0 4 0 5 1 7 0 2
80 160 1 6 3 8 4 10 7 14
Second ∞2 0 3 0 3 1 5
3 8 6 10 8 13 13 19
Third 80 240 0 3 1 4 2 6
0 2 5 10 8 13 12 17 19 25
M Fourth 320 1 4 2 5 3 7
0 3 7 11 11 15 17 20 25 29
Fifth 80 400
560 2 4 3 6 5 8
80 480 1 3 10 12 14 17 21 23 31 33
Sixth 1 3 3 5 4 6 7 9
Seventh 80 560 4 5 6 7 9 10 13 14 18 19 25 26 37 38
2 3
First 125 125 ∞2 ∞2 ∞3 ∞4 0 4 0 5 1 7 0 2
1 6 3 8 4 10 7 14
Second 125 250 ∞2 0 3 0 3 1 5
3 8 6 10 8 13 13 19
Third 1525 31755 0 2 0 3 1 4 2 6
N Fourth 125 500 1 4 2 5 3 7 5 10 8 13 12 17 19 25
0 3 7 11 11 15 17 20 25 29
Fifth 125
125 625 1 3 2 4 3 6 5 8
Sixth 125 750 3 5 4 6 7 9 10 12 14 17 21 23 31 33
1 3 13 14 18 19 25 26 37 38
Seventh 125 875
35 4 5 6 7 9 10
2 3
First 200 200 ∞2 ∞2 ∞3 ∞4 0 4 0 5 1 7 0 2
200 400 1 6 3 8 4 10 7 14
Second ∞2 0 3 0 3 1 5
3 8 6 10 8 13 13 19
Third 200 600 0 3 1 4 2 6
0 2 5 10 8 13 12 17 19 25
P Fourth 200 800 1 4 2 5 3 7
200 1000 0 3 7 11 11 15 17 20 25 29
Fifth 1 3 2 4 3 6 5 8
Sixth 200 1200 3 5 4 6 7 9 10 12 14 17 21 23 31 33
200 1400 1 3 13 14 18 19 25 26 37 38
Seventh 8 2 3 4 5 6 7 9 10
First 315 315 ∞2 ∞2 ∞3 ∞4 0 4 0 5 1 7 0 2
315 630 7 14
Second
315 945
∞2 0 3 0 3 1 5 1 6 3 8 4 10
13 19
Third 0 2 0 3 1 4 2 6 3 8 6 10 8 13
Q Fourth 5 10 8 13 12 17 19 25
0 3 1 4 2 5 3 7
Fifth 315 1575 7 11 11 15 17 20 25 29
1 3 2 4 3 6 5 8
Sixth 315 1890 10 12 14 17 21 23 31 33
1 3 3 5 4 6 7 9
Seventh 315 2205 13 14 18 19 25 26 37 38
2 3 4 5 6 7 9 10
First 00 0505 ∞2 ∞2 ∞3 ∞4 0 4 0 5 1 7 0 2
Second 500 1000 ∞2 0 3 0 3 1 5 1 6 3 8 4 10 7 14
Third 500 1500 0 2 0 3 1 4 2 6 3 8 6 10 8 13 13 19
R Fourth 500 2000 0 3 1 4 2 5 3 7 5 10 8 13 11 15 19 25
Fifth 500 2500 2 4 3 6 5 8 7 11 11 15 17 20 25 29
1 3
Sixth 500 3000 3 5 4 6 7 9 10 12 14 17 21 23 31 33
1 3
Seventh 500 3500 4 5 6 7 9 10 13 14 18 19 25 26 37 38
2 3
= Use first sampling plan below arrow. If sample size equals or exceeds lot or batch size, do 100 percent inspections.
= Use the first sampling plan above the arrow.
Ac = Acceptance number
Re = Rejection number
MULTIPLE
= Use corresponding single sampling plan (or alternatively, use double sampling plan below, where available) NORMAL
∞ = Acceptance not permitted at this sample size.
 MIL-STD-105E Page 26 of 74
TABLE IV-B– Multiple sampling plans for tightened inspection (Master table)
See 4.9.3. and 4.9.4)
Acceptable Quality Levels (tightened inspection)†
0.010 0.015 0.025 0.040 0.065 0.10 0.15 0.25 0.40 0.65 1.0 1.5 2.5 4.0 6.5 10 15 25 40 65 100 150 250 400 650 1000

Ac Re Come Here As it is Oh Really As it is Regarding theAc Re Ac Re Ac Re Regarding Ac Re Ac Re About Re What a thing As it is To Re Ac Re About Re It was Ac Re To this Oh, King The King The Re This Is It About Re

A
B ‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡
C
‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡
First 2 2 2 # 2 # 3 4 0 4 0 6 1 8 3 10 6 15
Second 2 4 2 0 3 0 3 1 5 2 7 3 9 6 12 10 17 16 25
Third 2 6 0 2 0 3 1 4 2 6 4 9 7 12 11 17 17 24 26 36
D Fourth 2 8 0 3 1 4 2 5 3 7 6 11 10 15 16 22 24 31 37 46
Fifth 2 10 1 3 2 4 3 6 5 8 9 12 14 17 22 25 32 37 49 55
Sixth 2 12 1 3 3 5 4 6 7 9 12 14 18 20 27 29 40 43 61 64
Seventh 2 14 2 3 4 5 6 7 9 10 14 15 22 22 32 33 48 49 72 73
First 3 3 2 2 3 # 4 0 4 0 6 1 8 3 10 6 15
Second 3 6 # 2 0 3 0 3 1 5 2 7 3 9 6 12 10 17 16 25
Third 3 9 0 2 0 3 1 4 2 6 4 9 7 12 11 17 17 24 26 36
E Fourth 3 12 0 3 1 4 2 5 3 7 6 11 10 15 16 22 24 31 37 46
Fifth 3 15 1 3 2 4 3 6 5 8 9 12 14 17 22 25 32 37 49 55
Sixth 3 18 1 3 3 5 4 6 7 9 12 14 18 20 27 29 40 43 61 64
Seventh 3 21 2 3 4 5 6 7 9 10 14 15 22 22 32 33 48 49 72 73
First 5 5 2 # 2 3 4 0 4 0 6 1 8
Second 5 10 # 2 0 3 0 3 1 5 2 7 3 9 6 12
Third 5 15 0 2 0 3 1 4 2 6 4 9 7 12 11 17
F Fourth 5 20 0 3 1 4 2 5 3 7 6 11 10 15 16 22
Fifth 5 25 1 3 2 4 3 6 5 8 9 12 14 17 22 25
Sixth 5 30 1 3 3 5 4 6 7 9 12 14 18 20 27 29
Seventh 5 35 2 3 4 5 6 7 9 10 14 15 22 22 32 33
First 8 8 2 2 3 4 0 4 0 6 1 8
Second 8 16 2 0 3 0 3 1 5 2 7 3 9 6 12
Third 8 24 0 2 0 3 1 4 2 6 4 9 7 12 11 17
G Fourth 8 32 0 3 1 4 2 5 3 7 6 11 10 15 16 22
Fifth 8 40 1 3 2 4 3 6 5 8 9 12 14 17 22 25
Sixth 8 48 1 3 3 5 4 6 7 9 12 14 18 20 27 29
Seventh 8 56 2 3 4 5 6 7 9 10 14 15 22 22 32 33
First 13 13 # 2 2 # 3 4 0 4 0 6 1 8
Second 13 26 2 0 3 0 3 1 5 2 7 3 9 6 12
Third 13 39 0 2 0 3 1 4 2 6 4 9 7 12 11 17
H Fourth 13 52 0 3 1 4 2 5 3 7 6 11 10 15 16 22
Fifth 13 65 1 3 2 4 3 6 5 8 9 12 14 17 22 25
Sixth 13 78 1 3 3 5 4 6 7 9 12 14 18 20 27 29
Seventh 13 91 2 3 4 5 6 7 9 10 14 15 22 22 32 33
First 20 20 2 # 2 3 # 4 0 4 0 6 1 8
Second 20 40 2 0 3 0 3 1 5 2 7 3 9 6 12
Third 20 60 0 2 0 3 1 4 2 6 4 9 7 12 11 17
J Fourth 20 80 0 3 1 4 2 5 3 7 6 11 10 15 16 22
Fifth 20 100 1 3 2 4 3 6 5 8 9 12 14 17 22 25
Sixth 20 120 1 3 3 5 4 6 7 9 12 14 18 20 27 29
Seventh 20 140 2 3 4 5 6 7 9 10 14 15 22 22 32 33
= Use the first sampling plan below the arrow. If the sample size equals or exceeds the lot or batch size, perform 100 percent inspections.
= Use the first sampling plan above the arrow.
Ac = Acceptance number
Re = Rejection number
MULTIPLE
= Use corresponding single sampling plan (or alternatively, use double sampling plan below, where available) TIGHTENED
‡ = Use the corresponding double sampling plan (or alternatively, use the double sampling plan below, where available)
# = Acceptance not permitted at this sample size.
 MIL-STD-105E Page 27 of 74
TABLE IV-B– Multiple sampling plans for tightened inspection (Master table)
(Continued) See 4.9.3. and 4.9.4)
Acceptable Quality Levels (tightened inspection)†
0.010 0.015 0.025 0.040 0.065 0.10 0.15 0.25 0.40 0.65 1.0 1.5 2.5 4.0 6.5 10 15 25 40 65 100 150 250 400 650 1000

In the end As it is Ac Re It relates to To go back Ac Re Formal Re Ac Re Oh King Ac Re Regarding This Ac Re As Re Ac Re About Re Ac Re A Re Yes Ac Re Ac Re Oh Really As is Material Regarding So Be It About Re

First 32 32 2 2 # 3 4 0 4 0 6 1 8
Second 32 64 2 0 3 0 3 1 5 2 7 3 9 6 12
Third 32 96 0 2 0 3 1 4 2 6 4 9 7 12 11 17
K Fourth 32 128 0 3 1 4 2 5 3 7 6 11 10 15 16 22
Fifth 32 160 1 3 2 4 3 6 5 8 9 12 14 17 22 25
Sixth 32 192 1 3 3 5 4 6 7 9 12 14 18 20 27 29
Seventh 32 224 2 3 4 5 6 7 9 10 14 15 21 22 32 33
First 50 50 2 # 2 3 # 4 0 4 0 6 1 8
Second 50 100 2 0 3 0 3 1 5 2 7 3 9 6 12
Third 50 150 0 2 0 3 1 4 2 6 4 9 7 12 11 17
L Fourth 50 200 0 3 1 4 2 5 3 7 6 11 10 15 16 22
Fifth 50 250 1 3 2 4 3 6 5 8 9 12 14 17 22 25
Sixth 50 300 1 3 3 5 4 6 7 9 12 14 18 20 27 29
Seventh 50 350 2 3 4 5 6 7 9 10 14 15 21 22 32 33
First 80 80 2 2 3 4 0 4 0 6 1 8
Second 80 160 2 0 3 0 3 1 5 2 7 3 9 6 12
Third 80 240 0 2 0 3 1 4 2 6 4 9 7 12 11 17
M Fourth 80 320 0 3 1 4 2 5 3 7 6 11 10 15 16 22
Fifth 80 400 1 3 2 4 3 6 5 8 9 12 14 17 22 25
Sixth 80 480 1 3 3 5 4 6 7 9 12 14 18 20 27 29
Seventh 80 560 2 3 4 5 6 7 9 10 14 15 21 22 32 33
First 125 125 2 2 3 4 0 4 0 6 1 8
Second 125 250 2 0 3 0 3 1 5 2 7 3 9 6 12
Third 125 375 0 2 0 3 1 4 2 6 4 9 7 12 11 17
N Fourth 125 500 0 3 1 4 2 5 3 7 6 11 10 15 16 22
Fifth 125 625 1 3 2 4 3 6 5 8 9 12 14 17 22 25
Sixth 125 750 1 3 3 5 4 6 7 9 12 14 18 20 27 29
Seventh 125 875 2 3 4 5 6 7 9 10 14 15 21 22 32 33
First 200 200 2 2 3 # 4 0 4 0 6 1 8
Second 200 400 2 0 3 0 3 1 5 2 7 3 9 6 12
Third 200 600 0 2 0 3 1 4 2 6 4 9 7 12 11 17
P Fourth 200 800 0 3 1 4 2 5 3 7 6 11 10 15 16 22
Fifth 200 1000 1 3 2 4 3 6 5 8 9 12 14 17 22 25
Sixth 200 1200 1 3 3 5 4 6 7 9 12 14 18 20 27 29
Seventh 200 1400 2 3 4 5 6 7 9 10 14 15 21 22 32 33
First 315 315 2 # 2 3 4 0 4 0 6 1 8
Second 315 630 # 2 0 3 0 3 1 5 2 7 3 9 6 12
Third 315 945 0 2 0 3 1 4 2 6 4 9 7 12 11 17
Q Fourth 315 1260 0 3 1 4 2 5 3 7 6 11 10 15 16 22
Fifth 315 1575 1 3 2 4 3 6 5 8 9 12 14 17 22 25
Sixth 315 1890 1 3 3 5 4 6 7 9 12 14 18 20 27 29
Seventh 315 2205 2 3 4 5 6 7 9 10 14 15 21 22 32 33
0 4
First 500 500 2 # 2 3 4 2 7 0 6 1 8
Second 500 1000 2 0 3 0 3 1 5 4 9 3 9 6 12
Third 500 1500 0 2 0 3 1 4 2 6 6 11 7 12 11 17
R Fourth 500 2000 0 3 1 4 2 5 3 7 9 12 10 15 16 22
Fifth 500 2500 1 3 2 4 3 6 5 8 12 14 17 22 25
Sixth 500 3000 1 3 3 5 4 6 7 9 14 18 20 27 29
Seventh 500 3500 2 3 4 5 6 7 9 10 14 21 22 32 33
15
S First 800 800 2
Second 800 1600 2
Third 800 2400 0 2
Fourth 800 3200 0 3
Fifth 800 4000 1 3
Sixth 800 4800 1 3
Seventh 800 5600 2 3
= Use the first sampling plan below the arrow. If the sample size is equal to or exceeds the lot or batch size, perform 100 percent inspections.
= Use the first sampling plan above the arrow. = Use corresponding single sampling plan (or alternatively, use double sampling plan below, where available) MULTIPLE
Ac = Acceptance number # Acceptance not permitted at this sample size.
Re = Rejection number TIGHTENED
 MIL-STD-105E Page 28 of 74
TABLE IV-C– Multiple sampling plans for reduced inspection (Master table)
See 4.9.3. and 4.9.4)
Acceptable Quality Levels (reduced inspection)†
0.010 0.015 0.025 0.040 0.065 0.10 0.15 0.25 0.40 0.65 1.0 1.5 2.5 4.0 6.5 10 15 25 40 65 100 150 250 400 650 1000

Ac Re As it is To be Ac Re As it is Regarding theAs It Is
matter Ac Re I have re Ac Re As It Is See you As it is Ac Re Ac Re Oh Really That is how it is Now As Re Here it is As it is Ac Re Ac Re According to Ac Re As it is

A
B
C
D
E ‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡
‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡
First 2 2 2 # 2 3 3 4 4 0 5 0 6
Second 2 4 2 3 3 0 4 0 5 1 6 1 7 3 9
Third 2 6 0 2 0 3 0 4 0 5 1 6 2 8 3 9 6 12
F Fourth 2 8 0 3 0 4 0 5 1 6 2 7 3 10 5 12 8 15
Fifth 2 10 0 3 0 4 1 6 2 7 3 8 5 11 7 13 11 17
Sixth 2 12 0 3 1 5 1 6 3 7 4 9 7 12 10 15 14 20
Seventh 2 14 1 3 1 5 2 7 4 8 6 10 9 11 13 17 18 22
First 3 3 2 # 2 3 3 # 4 4 0 5 0 6
Second 3 6 2 # 3 3 0 4 0 5 1 6 1 7 3 9
Third 3 9 0 2 0 3 0 4 0 5 1 6 2 8 3 9 6 12
G Fourth 3 12 0 3 0 4 0 5 1 6 2 7 3 10 5 12 8 15
Fifth 3 15 0 3 0 4 1 6 2 7 3 8 5 11 7 13 11 17
Sixth 3 18 0 3 1 5 1 6 3 7 4 9 7 12 10 15 14 20
Seventh 3 21 1 3 1 5 2 7 4 8 6 10 9 11 13 17 18 22
First 5 5 2 2 3 2 4 # 4 0 5 0 6
Second 5 10 # 2 # 3 3 2 0 5 1 6 1 7 3 9
Third 5 15 0 2 0 3 0 4 0 2 1 6 2 8 3 9 6 12
H Fourth 5 20 0 3 0 4 0 5 0 3 2 7 3 10 5 12 8 15
Fifth 5 25 0 3 0 4 1 6 1 3 3 8 5 11 7 13 11 17
Sixth 5 30 0 3 1 5 1 6 1 3 4 9 7 12 10 15 14 20
Seventh 5 35 1 3 1 5 2 7 2 3 6 10 9 11 13 17 18 22
First 8 8 2 2 3 2 4 # 4 0 5 0 6
Second 8 16 # 2 3 # 3 # 2 0 5 1 6 1 7 3 9
Third 8 24 0 2 0 3 0 4 0 2 1 6 2 8 3 9 6 12
J Fourth 8 32 0 3 0 4 0 5 0 3 2 7 3 10 5 12 8 15
Fifth 8 40 0 3 0 4 1 6 1 3 3 8 5 11 7 13 11 17
Sixth 8 48 0 3 1 5 1 6 1 3 4 9 7 12 10 15 14 20
Seventh 8 56 1 3 1 5 2 7 2 3 6 10 9 11 13 17 18 22
First 13 13 2 2 3 2 4 4 0 5 0 6
Second 13 26 2 3 3 2 0 5 1 6 1 7 3 9
Third 13 39 0 2 0 3 0 4 0 2 1 6 2 8 3 9 6 12
K Fourth 13 52 0 3 0 4 0 5 0 3 2 7 3 10 5 12 8 15
Fifth 13 65 0 3 0 4 1 6 1 3 3 8 5 11 7 13 11 17
Sixth 13 78 0 3 1 5 1 6 1 3 4 9 7 12 10 15 14 20
Seventh 13 91 1 3 1 5 2 7 2 3 6 10 9 11 13 17 18 22
= Use the first sampling plan below the arrow. If the sample size equals or exceeds the lot or batch size, perform 100 percent inspections.
= Use the first sampling plan above the arrow.
Ac = Acceptance number
Re = Rejection number
= Use corresponding single sampling plan (or alternatively, use double sampling plan below, where available) MULTIPLE
‡ = Use corresponding double sampling plan (or alternatively, use double sampling plan below, where available) REDUCED
RE
# = Acceptance not permitted at this sample size.
† = If, after the final sample, the acceptance number has been exceeded, but the rejection number has not been reached, accept the lot but reinstate normal inspection (See [Link])
 MIL-STD-105E Page 29 of 74
TABLE IV-C– Multiple sampling plans for reduced inspection (Master table)
(Continued) See 4.9.3. and 4.9.4)
Acceptable Quality Levels (reduced inspection)
0.010 0.015 0.025 0.040 0.065 0.10 0.15 0.25 0.40 0.65 1.0 1.5 2.5 4.0 6.5 10 15 25 40 65 100 150 250 400 650 1000

Ac Re Oh Yes Ac Re Ac Re With Re With regard toAc Re Oh Really As is Witch This is So be it It is As It Is About Re Ac Re Ac Re Ac Re Water Ac Re Concerning Ac Re Ac Re As it is So be it As Re

First 20 20 2 # 2 3 3 # 4 # 4 0 5 0 6
Second 20 40 # 2 3 # 3 0 4 0 5 1 6 1 7 3 9
Third 20 60 0 2 0 3 0 4 0 5 1 6 2 8 3 9 6 12
L Fourth 20 80 0 3 0 4 0 5 1 6 2 7 3 10 5 12 8 15
Fifth 20 100 0 3 0 4 1 6 2 7 3 8 5 11 7 13 11 17
Sixth 20 120 0 3 1 5 1 6 3 7 4 9 7 12 10 15 14 20
Seventh 20 140 1 3 1 5 2 7 4 8 6 10 9 14 13 17 18 22
First 32 32 # 2 2 3 3 4 4 0 5 4
Second 32 64 # 2 3 3 0 4 0 5 1 6 1 7 1 6
Third 32 96 0 2 0 3 0 4 0 5 1 6 2 8 3 9 2 8
M Fourth 32 128 0 3 0 4 0 5 1 6 2 7 3 10 5 12 3 10
Fifth 32 160 0 3 0 4 1 6 2 7 3 8 5 11 7 13 5 11
Sixth 32 192 0 3 1 5 1 6 3 7 4 9 7 12 10 15 7 12
Seventh 32 224 1 3 1 5 2 7 4 8 6 10 9 14 13 17 9 11
First 50 50 2 2 # 3 3 # 4 4 0 5 4
Second 50 100 2 3 3 0 4 0 5 1 6 1 7 1 6
Third 50 150 0 2 0 3 0 4 0 5 1 6 2 8 3 9 2 8
N Fourth 50 200 0 3 0 4 0 5 1 6 2 7 3 10 5 12 3 10
Fifth 50 250 0 3 0 4 1 6 2 7 3 8 5 11 7 13 5 11
Sixth 50 300 0 3 1 5 1 6 3 7 4 9 7 12 10 15 7 12
Seventh 50 350 1 3 1 5 2 7 4 8 6 10 9 14 13 17 9 11
First 80 80 2 2 3 3 4 4 0 5 4
Second 80 160 2 # 3 3 0 4 0 5 1 6 1 7 1 6
Third 80 240 0 2 0 3 0 4 0 5 1 6 2 8 3 9 2 8
P Fourth 80 320 0 3 0 4 0 5 1 6 2 7 3 10 5 12 3 10
Fifth 80 400 0 3 0 4 1 6 2 7 3 8 5 11 7 13 5 11
Sixth 80 480 0 3 1 5 1 6 3 7 4 9 7 12 10 15 7 12
Seventh 80 560 1 3 1 5 2 7 4 8 6 10 9 14 13 17 9 11
First 125 125 2 2 3 # 3 # 4 4 0 5 # 4
Second 125 250 2 3 3 0 4 0 5 1 6 1 7 1 6
Third 125 375 0 2 0 3 0 4 0 5 1 6 2 8 3 9 2 8
Q Fourth 125 500 0 3 0 4 0 5 1 6 2 7 3 10 5 12 3 10
Fifth 125 625 0 3 0 4 1 6 2 7 3 8 5 11 7 13 5 11
Sixth 125 750 0 3 1 5 1 6 3 7 4 9 7 12 10 15 7 12
Seventh 125 875 1 3 1 5 2 7 4 8 6 10 9 14 13 17 9 11
First 200 200 2 2 3 3 4 # 4 0 5 4
Second 200 400 2 # 3 3 0 4 0 5 1 6 1 7 1 6
Third 200 600 0 2 0 3 0 4 0 5 1 6 2 8 3 9 2 8
R Fourth 200 800 0 3 0 4 0 5 1 6 2 7 3 10 5 12 3 10
Fifth 200 1000 0 3 0 4 1 6 2 7 3 8 5 11 7 13 5 11
Sixth 200 1200 0 3 1 5 1 6 3 7 4 9 7 12 10 15 7 12
Seventh 200 1400 1 3 1 5 2 7 4 8 6 10 9 14 13 17 9 11
= Use the first sampling plan below the arrow. If the sample size equals or exceeds the lot or batch size, conduct 100 percent inspections.
= Use the first sampling plan above the arrow.
Ac = Acceptance number
Re = Rejection number
= Use corresponding single sampling plan (or alternatively, use double sampling plan below, where available) MULTIPLE
# = Acceptance not permitted at this sample size. REDUCED
† = If, after the final sample, the acceptance number has been exceeded, but the rejection number has not been reached, accept the lot but reinstate normal inspection (See [Link])