INTERNATIONAL ISO
STANDARD 4034
Third edition
1999-08-15
Hexagon nuts — Product grade C
Écrous hexagonaux — Grade C
A
Licensed to /FATOR TORNILLERIA INDUSTRIAL
ISO Store order #:806824/Downloaded:2007-02-26
Single user licence only, copying and networking prohibited
Reference number
ISO 4034:1999(E)
ISO 4034:1999(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
International Standard ISO 4034 was prepared by Technical Committee ISO/TC 2, Fasteners.
This third edition cancels and replaces the second edition (ISO 4034:1986) which has been technically revised.
© ISO 1999
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet iso@[Link]
Printed in Switzerland
Licensed to /FATOR TORNILLERIA INDUSTRIAL
ISO Store order #:806824/Downloaded:2007-02-26
Single user licence only, copying and networking prohibited
ii
© ISO ISO 4034:1999(E)
Introduction
This International Standard is part of the complete ISO product standard series on external hexagon drive
fasteners. The series comprises:
a) hexagon head bolts (ISO 4014 to ISO 4016 and ISO 8765);
b) hexagon head screws (ISO 4017, ISO 4018 and ISO 8676);
c) hexagon nuts (ISO 4032 to ISO 4036, ISO 8673 to ISO 8675);
d) hexagon bolts with flange (ISO 4162 and ISO 15071);
e) hexagon nuts with flange (ISO 4161 and ISO 10663);
f) structural bolts and nuts (ISO 4775, ISO 7411 to ISO 7414 and ISO 7417).
Licensed to /FATOR TORNILLERIA INDUSTRIAL
ISO Store order #:806824/Downloaded:2007-02-26
Single user licence only, copying and networking prohibited
iii
Licensed to /FATOR TORNILLERIA INDUSTRIAL
ISO Store order #:806824/Downloaded:2007-02-26
Single user licence only, copying and networking prohibited
INTERNATIONAL STANDARD © ISO ISO 4034:1999(E)
Hexagon nuts — Product grade C
1 Scope
This International Standard specifies the characteristics of hexagon nuts with threads from M5 up to and including M64
and product grade C.
If, in special cases, specifications other than those listed in this International Standard are required, they should be
selected from existing International Standards, for example ISO 724, ISO 898-2, ISO 965-1 and ISO 4759-1.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this International Standard. For dated references, subsequent amendments to, or revisions of, any of these
publications do not apply. However, parties to agreements based on this International Standard are encouraged to
investigate the possibility of applying the most recent editions of the normative documents indicated below. For
undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC
maintain registers of currently valid International Standards.
ISO 225:1983, Fasteners — Bolts, screws, studs and nuts — Symbols and designations of dimensions.
ISO 724:1993, ISO general-purpose metric screw threads — Basic dimensions.
ISO 898-2:1992, Mechanical properties of fasteners — Part 2: Nuts with specified proof load values — Coarse
thread.
ISO 965-1:1998, ISO general purpose metric screw threads — Tolerances — Part 1: Principles and basic data.
ISO 3269:—1), Fasteners — Acceptance inspection.
ISO 4042:1999, Fasteners — Electroplated coatings.
ISO 4759-1:—2), Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B and C.
ISO 8992:1986, Fasteners — General requirements for bolts, screws, studs and nuts.
ISO 10683:—3), Fasteners — Non-electrolytically applied zinc flake coatings.
1) To be published. (Revision of ISO 3269:1988)
2) To be published. (Revision of ISO 4759-1:1978)
3) To be published.
Licensed to /FATOR TORNILLERIA INDUSTRIAL
ISO Store order #:806824/Downloaded:2007-02-26
Single user licence only, copying and networking prohibited
1
ISO 4034:1999(E) © ISO
3 Dimensions
See Figure 1 and Tables 1 and 2.
Symbols and descriptions of dimensions are defined in ISO 225.
a b = 15∞ to 30∞
b Countersink at start of thread permissible
Figure 1
Table 1 — Preferred threads
Dimensions in millimetres
Thread (d) M5 M6 M8 M10 M12 M16 M20
Pa 0,8 1 1,25 1,5 1,75 2 2,5
dw min. 6,7 8,7 11,5 14,5 16,5 22 27,7
e min. 8,63 10,89 14,2 17,59 19,85 26,17 32,95
m max. 5,6 6,4 7,9 9,5 12,2 15,9 19,0
min. 4,4 4,9 6,4 8,0 10,4 14,1 16,9
mw min. 3,5 3,7 5,1 6,4 8,3 11,3 13,5
s nom. = max. 8,00 10,00 13,00 16,00 18,00 24,00 30,00
min. 7,64 9,64 12,57 15,57 17,57 23,16 29,16
Thread (d) M24 M30 M36 M42 M48 M56 M64
Pa 3 3,5 4 4,5 5 5,5 6
dw min. 33,3 42,8 51,1 60 69,5 78,7 88,2
e min. 39,55 50,85 60,79 71,3 82,6 93,56 104,86
m max. 22,3 26,4 31,9 34,9 38,9 45,9 52,4
min. 20,2 24,3 29,4 32,4 36,4 43,4 49,4
mw min. 16,2 19,4 23,2 25,9 29,1 34,7 39,5
s nom. = max. 36 46 55,0 65,0 75,0 85,0 95,0
min. 35 45 53,8 63,1 73,1 82,8 92,8
a P is the pitch of the thread.
Licensed to /FATOR TORNILLERIA INDUSTRIAL
ISO Store order #:806824/Downloaded:2007-02-26
Single user licence only, copying and networking prohibited
2
© ISO ISO 4034:1999(E)
Table 2 — Non-preferred threads
Dimensions in millimetres
Thread (d) M14 M18 M22 M27 M33 M39 M45 M52 M60
Pa 2 2,5 2,5 3 3,5 4 4,5 5 5,5
dw min. 19,2 24,9 31,4 38 46,6 55,9 64,7 74,2 83,4
e min. 22,78 29,56 37,29 45,2 55,37 66,44 76,95 88,25 99,21
m max. 13,9 16,9 20,2 24,7 29,5 34,3 36,9 42,9 48,9
min. 12,1 15,1 18,1 22,6 27,4 31,8 34,4 40,4 46,4
mw min. 9,7 12,1 14,5 18,1 21,9 25,4 27,5 32,3 37,1
s nom. = max. 21,00 27,00 34 41 50 60,0 70,0 80,0 90,0
min. 20,16 26,16 33 40 49 58,8 68,1 78,1 87,8
a P is the pitch of the thread.
4 Specifications and reference standards
See Table 3.
Table 3 — Specification and reference standards
Material Steel
General International ISO 8992
requirements Standard
Thread Tolerance 7H
International ISO 724, ISO 965-1
Standards
Mechanical Property d ⭐ M16: 5
properties classa M16 ⬍ d ⭐ M39: 4, 5
d ⬎ M39: as agreed
International d ⭐ M39: ISO 898-2
Standard d ⬎ M39: as agreed
Tolerances Product grade C
International ISO 4759-1
Standard
Finish and/or coating As processed
Requirements for electroplating are covered in ISO 4042.
Requirements for non-electrolytically applied zinc flake coatings are covered in
ISO 10683.
If different electroplating requirements are desired or if requirements are needed
for other finishes, they should be agreed between customer and supplier.
Acceptability For acceptance procedure, see ISO 3269.
a For other property classes see ISO 898-2.
Licensed to /FATOR TORNILLERIA INDUSTRIAL
ISO Store order #:806824/Downloaded:2007-02-26
Single user licence only, copying and networking prohibited
3
ISO 4034:1999(E) © ISO
5 Designation
EXAMPLE
A hexagon nut with thread M12 and property class 5 is designated as follows:
Hexagon nut ISO 4034 - M12 - 5
Licensed to /FATOR TORNILLERIA INDUSTRIAL
ISO Store order #:806824/Downloaded:2007-02-26
Single user licence only, copying and networking prohibited
4
© ISO ISO 4034:1999(E)
Bibliography
[1] ISO 4014:1999, Hexagon head bolts — Product grades A and B.
[2] ISO 4015:1979, Hexagon head bolts — Product grade B — Reduced shank (shank diameter approximately
equal to pitch diameter).
[3] ISO 4016:1999, Hexagon head bolts — Product grade C.
[4] ISO 4017:1999, Hexagon head screws — Product grades A and B.
[5] ISO 4018:1999, Hexagon head screws — Product grade C.
[6] ISO 4032:1999, Hexagon nuts, style 1 — Product grades A and B.
[7] ISO 4033:1999, Hexagon nuts, style 2 — Product grades A and B.
[8] ISO 4035:1999, Hexagon thin nuts (chamfered) — Product grades A and B.
[9] ISO 4036:1999, Hexagon thin nuts (unchamfered) — Product grade B.
[10] ISO 4161:1999, Hexagon nuts with flange — Coarse thread.
[11] ISO 4162:—4), Hexagon bolts with flange — Small series — Product grade combination A/B.
[12] ISO 4775:1984, Hexagon nuts for high-strength structural bolting with large width across flats — Product
grade B — Property classes 8 and 10.
[13] ISO 7411:1984, Hexagon bolts for high-strength structural bolting with large width across flats (thread lengths
according to ISO 888) — Product grade C — Property classes 8.8 and 10.9.
[14] ISO 7412:1984, Hexagon bolts for high-strength structural bolting with large width across flats (short thread
length) — Product grade C — Property classes 8.8 and 10.9.
[15] ISO 7413:1984, Hexagon nuts for structural bolting, style 1, hot-dip galvanized (oversize tapped) — Product
grades A and B — Property classes 5, 6 and 8.
[16] ISO 7414:1984, Hexagon nuts for structural bolting with large width across flats, style 1 — Product grade B —
Property class 10.
[17] ISO 7417:1984, Hexagon nuts for structural bolting, style 2, hot-dip galvanized (oversize tapped) — Product
grade A — Property class 9.
[18] ISO 8673:1999, Hexagon nuts, style 1, with metric fine pitch thread — Product grades A and B.
[19] ISO 8674:1999, Hexagon nuts, style 2, with metric fine pitch thread — Product grades A and B.
[20] ISO 8675:1999, Hexagon thin nuts (chamfered) with metric fine pitch thread — Product grades A and B.
[21] ISO 8676:1999, Hexagon head screws with metric fine pitch thread — Product grades A and B.
[22] ISO 8765:1999, Hexagon head bolts with metric fine pitch thread — Product grades A and B.
[23] ISO 10663:1999, Hexagon nuts with flange — Fine pitch thread.
[24] ISO 15071:1999, Hexagon bolts with flange — Small series — Product grade A.
4) To be published. (Revision of ISO 4162:1990)
Licensed to /FATOR TORNILLERIA INDUSTRIAL
ISO Store order #:806824/Downloaded:2007-02-26
Single user licence only, copying and networking prohibited
5
ISO 4034:1999(E) © ISO
ICS 21.060.20
Licensed to /FATOR TORNILLERIA INDUSTRIAL
Price based on 5 pages ISO Store order #:806824/Downloaded:2007-02-26
Single user licence only, copying and networking prohibited
