YUPO QUICK GUIDE

HEAD OFFICE
Shin-Ochanomizu Building, 15th Floor, Kanda-Surugadai 4-3
Chiyoda-ku, Tokyo 101-0062, JAPAN
Phone: +81-3-5281-0813 Fax: +81-3-5281-0819

KASHIMA FACTORY
23 Towada, Kamisu-shi, Ibaraki 314-0102, JAPAN
Phone: +81-299-96-2931 Fax: +81-299-96-5099

KASHIMA FACTORY is registered "ISO 9001" (Registered NO.JCQA-0124)

& "ISO 14001" (Registered NO.JCQA-E-00125)

ht tp://w w w.yupo.com

“YUPO” is registered trademark of YUPO CORPORATION, Tokyo Japan.

* Examples shown below are all our registered trademarks.
* Part of the trademarks we hold is displayed.

YUPO CLOTHYUPO ʸ@<76 AQUAYUPO

SUPERYUPO HIGHTEAR YUPO ALPHAYUPO YUPOBLUE
YUPOTRACE YUPOJET ULTRAYUPO YUPO OCTOPUS

* The contents of this catalogue are as of January 2017.

Please note that it may be subject to change without notice for further improvement.
* FGS150 is used (UV offset printing) * All Rights Reserved. * All photos are for illustrative purposes only. English ver.
©2015 YUPO CORPORATION 1.2017 5,000 GM
 Environmentally friendly synthetic paper Tougher than paper and more expressive than film.
to protect the forest, the water, and the air. YUPO is known for its water resistance, but that is not the only advantage it possesses.
It has many other advantages over other synthetic paper, and this versatility is its greatest strength.
YUPO was designed as a new-age paper product to replace conventional paper,
which is made from wood pulp. It contributes to environmental conservation and
reduced environmental impact in a number of ways.

Compared to paper…

Water resistant Tough Oil and chemical resistant

Protecting YUPO has exceptional water resis- Far tougher than paper in terms of There is almost no deterioration in
the Forest tance, so it will rarely lose strength or stretching, folding, and shock quality when exposed to oils, acids,
YUPO is mainly become misshapen when wet. resistance. Even tougher laminated alkalis, or organic solvents, etc.
made from polypropylene. products are available.
It does not contain wood pulp.
Oil Chemicals

Protecting
Becomes an
the Water
Energy Resource
Making conventional paper
Used YUPO can be recycled
requires vast amounts of
as a refuse paper and plastic
clean water, but YUPO
fuel (RPF) for boilers, etc.
requires very little water.

Clean (low dust) Light (cushioned) Smooth surface

YUPO’s Features
YUPO produces approximately 1/100 Due to its special construction, which The surface is smooth, so it also
of the dust of high-quality paper. It incorporates micro-voids (microscopic provides a very attractive finish when
hardly produces any dust, even when pores), YUPO is only 2/3 of the weight used for lamination or other such
folded or abraded. of coated paper of an equivalent purpose.
thickness. It is so light, it floats.

Protecting Trim Edge

High-quality paper YUPO
the Air are Reusable YUPO
YUPO does not use chemicals Offcuts that are produced Coated paper
that place a strain on the during the production process
environment, such as toxic heavy can be reused as raw material.
metals, accumulative toxins, and
ozone-depleting substances.

Combating
Climate Change
The amount of CO 2 emitted
during production is about the
same as that for conventional
paper, and less than film.
Compared to film…

* If natural paper is compared with FGS 80

Prints clearly Suitable for handwriting Many variations available
* Calculated based on surface area
YUPO is suitable for a range of In addition to oil-based pens, some A range of unique products is
printing methods, producing vibrant products can be written on with pencils. available, such as adhesive products,
colors – just like paper. YUPO provides a smooth writing translucent products, and metallic
surface without sticking or slipping. products. Products are also available
in a range of calipers.

Produced in a factory with ISO 14001 certification. Film YUPO Oil-based pen Pencil Adhesive Translucent Metallic
ISO 14001 is the international standard for “Environmental Management
Systems.” It requires continuous improvement of the environmental
impact of business activities.
YUPO CORPORATION obtained this certification for our Kashima factory
and research and development laboratory in March 2000, and based on <Disposing of YUPO>
our environmental policy, we have been contributing to the local When discarding it as ordinary household waste, please dispose of it as the category of
community and global environment through energy conservation, plastic defined by the municipality of residence.
recycling, waste reduction, and prevention of contamination and accidents. When disposing of it as waste at a business establishment, please treat it as industrial waste.

3 4
 Product Lineup
YUPO comes in many product variations, so you can choose the best one for your use or printing method.

Standard

General YUPO (UV ink) Matte ULTRAYUPO™ Semi-gloss SUPERYUPO™ Semi-gloss

This all-purpose product is available in This t ype dramatically shor tens the This product allows oil-based offset
a variety of calipers. It is not only drying time of YUPO ink, allowing you printing using general-paper ink. There
suitable for oil-based offset printing, to deliver the product earlier. There is is no need to switch to YUPO ink, and
but also for UV offset printing. almost no dot gain. since drying time is short, you can
deliver the product earlier. There is
almost no dot gain.
Features of Standard Products

Technical General YUPO (UV ink) ULTRAYUPO™ SUPERYUPO™

Information Printing method

Oil-based offset printing (YUPO ink)
UV offset printing
Silk-screen printing
Oil-based offset printing (YUPO ink)
UV offset printing
Silk-screen printing * Edge-picking
Oil-based offset printing
(General-paper ink/YUPO ink)

Gravure printing Gravure printing may occur

YUPO is not difficult to convert
Printing surface Both sides Both sides Single side
if you are aware of the key points.

Product Lineup
Front Matte Semi-gloss Semi-gloss (Printing surface)
Surface
The following pages contain notes on printing and gloss
Back Matte Semi-gloss Matte
processing as well as special features of each
Suitability Pencil × ×
product’s specifications, etc. for hand-
writing Oil-based pen
Please refer to the provided technical manual for
Halftone reproduction Inferior to coated paper Same level as coated paper Same level as coated paper
detailed information.

Translucent Thick

YUPOTRACE™ ALPHAYUPO™
YUPO™ Back Light

Label Adhesive

Face Stock for Sticker Label YUPO OCTOPUS™

Easy De-Laminate YUPO/Destructive YUPO YUPOSTATIC™
AQUAYUPO™
In Mold grade

Laminated For digital printing

CLOTHYUPO™ YUPOJET™
YUPO™ Metalized YUPOBLUE™ (Certified for HP Indigo)
HIGHTEAR YUPO™ YUPO™ for UV silk screen/UV inkjet
YUPO™ 100% Opacity

15 16
Delivery Folding

Perforation

Drying

Wet Lamination/Dry Lamination

Printing on YUPO/Converting YUPO

Adhesive

Trimming

Punching (Die Cutting)

 Main Product List
Appropriate Appropriate in some circumstances Blank Inappropriate
Category

Printing method
Printing
Product name Grade Product features & precautions
surface
Oil-based offset printing UV offset printing Other printing Digital printing

FPG 60, FPG 80, FPG 95

This all-purpose product is used for a range of applications.
General YUPO (Oxidation ink) FPG 110, FPG 130, FPG 150 YUPO ink Gravure printing
Both sides
Suitable for oil-based offset and gravure printing.
FPG 200, FPG 250, FPG 300

This all-purpose product is available in a variety of calipers.

FGS 60, FGS 80, FGS 95 Not only highly suitable for oil-based offset printing, but also UV offset printing.
General YUPO (UV ink) FGS 110 , FGS 130, FGS 150 YUPO ink Silk-screen printing/Gravure printing
Both sides Both front and back surfaces are matte.
FGS 200, FGS 250, FGS 300 Can be written on with pencil.
Ink setting takes 10-16 hours for a 4-color overlay (measurement example).
Standard

Fast drying time with YUPO ink.

FEB 95, FEB 110, FEB 130 The short drying time allows you to deliver the product earlier.
FEB 150, FEB 200, FEB 250 Color reproduction is exceptional, with minimal dot gain.
ULTRAYUPO™ YUPO ink Silk-screen printing/Gravure printing
Both sides
Both front and back surfaces are semi-gloss.
Ink setting takes 5-7 hours for a 4-color overlay (measurement example).
FEBA 300 * Edge-picking may occur in UV offset printing. Please contact us for further details.

This product allows oil-based offset printing with general-paper ink.

FRB 110, FRB 130 Because there is no need to switch to YUPO ink, and the drying time is short,
you can deliver the product earlier.
Color reproduction is exceptional, with minimal dot gain.
SUPERYUPO™ General-paper ink/YUPO ink
Single side
The front (printing surface) is semi-gloss and the back side is matte.
Ink setting time is less than 4 hours for a 4-color overlay with FRB
FRR 70 (measurement example), and less than 4 hours for a 2-color overlay with FRR.
* Only compatible with overlay of 2 colors or less when using FRR with ink for standard paper.

This product is thin-type translucent.

YUPOTRACE™ TPRA 60, TPRA 90 YUPO ink (Low energy UV lamp recommended) Gravure printing
Both sides It is used for items such as photographic screens and wrapping for frozen foods.
Translucent

Can be written on.

This product is translucent and was developed for illuminated signs.

BLR 150 Good light diffusion properties make images appear clearly when backlit.

Main Product List

BLR is suitable for designs with warm colors and BCR is suitable
YUPO™ Back Light YUPO ink
Both sides
for designs with bluish-white colors.
BCR 160 * Printing with HP Indigo is possible, but the water-resistant and ink adhesion
is weak, so please use it for indoor applications.

ALPHAYUPO™ QJJ 350, QJJ 400, QJJ 500

This thicker product is available in many variations, including standard,
Thick

ingle-side gloss, and translucent type.

ALPHAYUPO™ (Gloss type) QTYR 350 YUPO ink
Silk-screen printing/ Both sides
Knife folding may cause breakage.
UV letterpress printing
Scoring and creasing is recommended instead.
ALPHAYUPO™ (Translucent type) RMM 400

Face Stock for Sticker Label SGS 60, SGS 80, SGS 110
The reverse (adhesive surface) is a strong base for pressure-sensitive labels.
Silk-screen printing/ Single side
YUPO ink Strength between layers makes it suitable for removable labels.
UV letterpress printing
Face Stock for Sticker Label (TTR/Removable type) SGP 80, SGP 110

A pattern printed on the adhesive of the reverse side that remains on the surface
Easy De-Laminate YUPO SAR 60 Both sides
to which the label was affixed after it is peeled off.
Silk-screen printing/
YUPO ink The label tears apart when removed, leaving evidence of opening the product
UV letterpress printing
Destructive YUPO SLR 80 Single side
packaging.

This product is for glued on labels and thermal labels.

Gravure printing/ The reverse absorbs water, so it is possible to use water-based adhesives.
AQUAYUPO™ LAR 75, LAR 95 YUPO ink (Low energy UV lamp recommended) UV letterpress printing/
Single side
Labels on containers can be removed cleanly, which is useful for garbage separation and recycling.
UV flexo printing * Edge-picking may occur in UV offset printing. Please contact us for further details.

In-mold labels can be labeled at the same time as producing the bottle.
ITE 105 Good for high-speed forming, wide window-molding conditions.
For label

In-mold labels can be labeled at the same time as producing the bottle.
ISF 105 Good for high-speed forming, wide window-molding conditions and anti-static properties.
Silk-screen printing/
In Mold grade for Blow/Injection molding YUPO ink UV letterpress printing/
Single side
In-mold labels can be labeled at the same time as producing the bottle.
IDF 80, IDF 100 UV flexo printing
No orange-peel properties.
In-mold labels can be labeled at the same time as producing the bottle.
IHC 75
Transparent type and no orange-peel properties.
In-mold labels can be labeled at the same time as producing the bottle.
LBR 80 YUPO ink Gravure printing
Single side
No orange-peel and wide window-molding conditions.

In-mold labels can be labeled at the same time as producing the bottle.
UAIB 80 UV letterpress printing/ Single side High-transparent type and no orange-peel properties.
UV flexo printing Corona treatment is required before printing.
In Mold grade for Injection molding

In-mold labels can be labeled at the same time as producing the bottle.
FGS 80 YUPO ink Silk-screen printing/Gravure printing
Both sides Good for wide window-molding conditions.
* Using the standard “FGS” product.

19 20
 Main Product List
Appropriate Appropriate in some circumstances Blank Inappropriate
Category

Printing method
Printing
Product name Grade Product features & precautions
surface
Oil-based offset printing UV offset printing Other printing Digital printing

YUPO OCTOPUS™ (Offset ink) WKFS 340 General-paper ink/YUPO ink

This micro-suction sheet can be stuck to smooth surfaces and then removed
WKJ 250 Inkjet printers (Water-based pigment ink) and reused, even multiple times.
YUPO OCTOPUS™ (Inkjet ink) Easily adheres to surfaces while excluding air.
WKE 250 Inkjet printers (Eco-solvent ink) Because adhesive is not used, no residue is left on the surface after removal.
Single side If the adhesive surface becomes dirty, rinse off the dirt with water and then
dry it to restore the adhesive properties.
YUPO OCTOPUS™ (HP Indigo) XAD 1058
Stick type

HP Indigo * Printing is not possible on the adhesive side.

* Cannot be used for car stickers or on wired glass.
YUPO OCTOPUS™ (Clear) XAD 1068 UV inkjet printers * Not suited to outdoor uses.

YUPO OCTOPUS™ (UV silk screen/UV inkjet) XAD 1069 UV silk-screen printing UV inkjet printers

YUPOSTATIC™ (Offset ink/UV inkjet) WESC 165 UV inkjet printers

Both sides This sheet uses static electricity to adhere to surfaces.
It can stick to uneven surfaces such as walls.
Because adhesive is not used, no residue is left on the surface after removal.
YUPOSTATIC™ (Inkjet ink) WEJ 200 Inkjet printers (Water-based dye or pigment ink)
Single side
* When peeled off once, the material loses some of static electricity power,
so it cannot be reused multiple times.
YUPOSTATIC™ (HP Indigo) WESA 165 Both sides * Not suited to outdoor uses.
HP Indigo

CLOTHYUPO™
(Laminated with synthetic woven cloth/ WNF 135 Silk-screen printing
Single side
This product is laminated with YUPO and cloth (synthetic fiber).
single side) Exceptional toughness makes it suitable for processes such as
machine sewing and wire threading.
It is appropriate for large printed materials, such as hangings
CLOTHYUPO™ and cloth banners.
(Laminated with synthetic woven cloth/ WNFW 200 YUPO ink
Both sides
double side)
Laminated

YUPO ink/
YUPO™ Metalized WMF 120 Use ink for aluminum foil
Both sides This product is laminated with metalized PET.

Main Product List

(metallic finish surfaces only)

This product is laminated with YUPO and non-woven fabric.

Exceptional toughness makes it suitable for processes such as machine
HIGHTEAR YUPO™ WSF 110, WSF 160 YUPO ink
Both sides
sewing and wire threading.
Traditional Japanese paper texture.

This product is 100% opaque for complete black-out effect.

YUPO™ 100% Opacity WCFA 125, WCFA 195 YUPO ink Both sides
Suitable for double-sided printing as there is no see-through.

VJFP 120, VJFP 170, VJFP 190 Inkjet printers (Water-based pigment ink)

This product is suitable for wide-format inkjet printers.

Unlike paper, it does not swell due to humidity or ink. Because it is
YUPOJET™ XAB 1020 Inkjet printers Single side
tear-resistant, you can print with confidence on large sheets.
(Water-based dye or pigment ink)
For digital printing

* Please enquire about the many other types we produce.

VJFN 160
Inkjet printers (Eco-solvent ink)

This product is ideal for HP Indigo digital printers.

Double-sided printing is possible without pre-coating. High water resistance
YPI 150, YPI 200 UV letterpress printing/ and rubbing resistance.
YUPOBLUE™ (Certified for HP Indigo) YUPO ink UV flexo printing/ HP Indigo/Thermal transfer
Both sides
YPI 250, YPI 300 It is suitable for a range of printing methods, from HP Indigo digital
UV form offset printing, etc. printing to various types of UV printing.
* Please consult us for further details.

YUPO™ for UV silk screen/UV inkjet FPU 130, FPU 200, FPU 250 UV silk-screen printing UV inkjet printers
Both sides This product is suitable for UV inkjet printers.

21 22
 Stock List *Consult us for special-size orders. YUPO’s Manufacturing Process

Category Product name Grade Sheet products Sheets per package Roll Roll size

FPG 60 500
YUPO’s unique production method is
Raw material
(polypropylene) patented around the world.
General YUPO (Oxidation ink) FPG 80, FPG 95, FPG 110, FPG 130, FPG 150 250
YUPO is made up of 3 layers. The base layer is
FPG 200, FPG 250, FPG 300 125
stretched both lengthwise and crosswise, while
Additives
FGS 60 500 the surface layer is stretched crosswise (bi-axially
General YUPO (UV ink) FGS 80, FGS 95, FGS 110, FGS 130, FGS 150 250 oriented film forming process). This production
Standard

method is only possible because of our unique

FGS 200, FGS 250, FGS 300 125
technology, which is protected by patents around
FEB 95, FEB 110, FEB 130, FEB 150 250 the world, including in Japan, America, and China.
ULTRAYUPO™ FEB 200, FEB 250 125

FEBA 300 125

Pelletizing 1
FRB 110, FRB 130 250 Producing pellets
SUPERYUPO™
FRR 70 250 Pellets are made by adding inorganic
TPRA 60 500
filler and additives to polypropylene.
YUPOTRACE™
Translucent

TPRA 90 250
Pellets
BLR 150 250
YUPO™ Back Light 2 3
BCR 160 250
Stretched in machine direction Stretched in cross direction
Material expelled from the extruder The base layer is laminated on each
ALPHAYUPO™ QJJ 350, QJJ 400, QJJ 500 100
is stretched in the machine direction side with the surface layer, and is
Thick

ALPHAYUPO™ (Gloss type) QTYR 350 100 using rollers to form the base layer. then stretched in the cross direction.
ALPHAYUPO™ (Translucent type) RMM 400 100

Face Stock for Sticker Label SGS 60, SGS 80, SGS 110

YUPO’s manufacturing process and structure

Face Stock for Sticker Label SGP 80, SGP 110 Surface layer
(TTR/Removable type)
Extruder
Easy De-Laminate YUPO SAR 60

Destructive YUPO SLR 80

Extruder
LAR 75 Base layer
Surface layer
AQUAYUPO™

Stock List/
LAR 95 250
For label

ITE 105 250

Extruder
Trimmed edges produced during the production
ISF 105 250 process can be reused as raw material.

In Mold grade for Blow/Injection molding IDF 80 250

IDF 100 250

IHC 75 250 YUPO’s Structure

LBR 80 250
Strength comes from the base layer,
Micro-voids
In Mold grade for Injection molding while the paper-like characteristics
UAIB 80 Cross direction
Machine direction (CD) come from the surface layers.
YUPO OCTOPUS™ (Offset ink) WKFS 340 100 (MD)
YUPO is a synthetic paper made up of 3 layers: a
YUPO OCTOPUS™ (Inkjet ink) WKJ 250 610x20m, 914x20m, 1,270x20m base layer and a surface layer laminated to each
Surface layer
WKE 250 Base layer
side. The base layer gives YUPO strength, while
YUPO OCTOPUS™ (HP Indigo) the stretching process provides the surface
Surface layer
XAD 1058 250
Stick type

layers with innumerable micro-voids

YUPO OCTOPUS™ (Clear) XAD 1068 1,270x20m (microscopic pores), which make it very white, as
YUPO OCTOPUS™ (UV silk screen/UV inkjet) XAD 1069 1,270x20m well as lightweight and suitable for handwriting.
YUPOSTATIC™ (Offset ink) WESC 165 250 1,240x50m

YUPOSTATIC™ (Inkjet ink) WEJ 200 1,240x50m

YUPOSTATIC™ (HP Indigo) WESA 165 250

CLOTHYUPO™ WNF 135 Check YUPO’s grain. The grain direction has double the stiffness.
(Laminated with synthetic woven cloth/single side)
CLOTHYUPO™ WNFW 200 125 Just like paper, YUPO has a grain. The grain runs along the first For uses that require stiffness, such as swing POPs, make sure the
(Laminated with synthetic woven cloth/double side)
dimension listed in the label, so make sure you check this before use. grain is aligned with the curve. The stiffness in the direction of the
Laminated

YUPO™ Metalized WMF 120 100

Many YUPO sheets have a short grain; however some products that grain has twice that of the grain.
HIGHTEAR YUPO™ WSF 110, WSF 160 100 are prone to fanning out (inaccurate registration) have a long grain.

WCFA 125 250 Low stiffness High stiffness

YUPO™ 100% Opacity Grain direction of roll products Grain direction of sheet products POP shape
WCFA 195 125
Example Example
VJFP 120, VJFP 170, VJFP 190 914x30m, 1,270x30m
1,000mm×3,000m 788×1,091mm

YUPO’s grain
For digital printing

YUPOJET™ XAB 1020 610x30m, 914x30m, 1,270x30m

Curve
VJFN 160 1,370x30m
YUPO’s grain
YUPO’s grain
YPI 150 250
YUPOBLUE™ (Certified for HP Indigo) YUPO’s grain
YPI 200, YPI 250, YPI 300 125

YUPO™ for UV silk screen/UV inkjet FPU 130, FPU 200, FPU 250

23 24
 Physical Properties (General Properties of Each Product)

Gloss (%) Tensile strength (kN/m) Elongation (%) Clark stiffness (S value) Gloss (%) Tensile strength (kN/m) Elongation (%) Clark stiffness (S value)
Thickness Basis weight Density Whiteness Opacity Specific surface Thickness Basis weight Density Whiteness Opacity Specific surface
Grade
(μm) (g/ ) (g/ ) (%) (%)
Grade (μm) (g/ ) (g/ ) (%) (%)
resistance (ƃ) UHVLVWDQFH ƃ
Front/Back MD CD MD CD MD CD Front/Back MD CD MD CD MD CD

Front: 1×1011
FPG 60 60 47.4 0.79 96 87 16 3 9 115 30 15 25 1×10
11
ITE 105 107 81.6 0.76 97 94 19/52 4 10 140 20 15 45 Back: 1×1015
Front: 1×1011
FPG 80 80 61.6 0.77 96 90 17 4 10 125 30 20 40 1×1011 ISF 105 107 82.7 0.77 97 94 24/65 4 10 140 20 15 45 Back: 1×1013
Front: 1×1011
FPG 95 95 73.2 0.77 96 92 17 6 15 125 25 30 60 1×1011 IDF 80 81 75.2 0.93 96 86 25/65 4 15 165 30 15 25 Back: 1×1015
Front: 1×1011
FPG 110 110 84.7 0.77 96 94 17 6 15 130 25 40 80 1×1011 IDF 100 101 92.0 0.91 96 91 25/65 5 15 170 30 20 45 Back: 1×1015
Front: 1×1015
FPG 130 130 100.1 0.77 96 95 17 7 20 130 25 55 110 1×1011 IHC 75 77 68.8 0.90 90 14 64/85 6 20 180 30 15 35 Back: 1×1015
Front: 1×1011
FPG 150 150 115.5 0.77 96 96 17 8 20 140 25 70 145 1×1011 LBR 80 80 66.4 0.83 96 85 55/14 4 10 150 30 15 30 Back: 1×1011

FPG 200 200 158.0 0.79 96 98 16 10 30 155 30 125 255 1×1011 UAIB 80 87 72.1 0.83 – 11 59/19 – – – – 11 – Back: 9×1013>

FPG 250 250 200.0 0.80 96 99 15 10 35 165 30 200 300< 1×1011 WKFS 340 320 220.0 0.69 97 97 – – – – – – – –

FPG 300 300 234.0 0.78 96 99 15 9 35 130 30 270 300< 1×10 11

WKJ 250 220 156.0 0.71 97 95 – – – – – – – –

FGS 60 65 51.4 0.79 97 87 16 3 7 115 25 15 20 1×10 11

WKE 250 245 175.0 0.71 90 96 – – – – – – – –

FGS 80 80 61.6 0.77 97 91 17 4 10 130 30 20 30 1×10 11

XAD 1058 210 170.0 0.78 96 93 – – – – – – – 1×10
11

FGS 95 95 73.2 0.77 97 93 17 5 15 130 30 30 45 1×1011 XAD 1068 178 235.0 1.30 – – 101 – – – – – – –

FGS 110 110 84.7 0.77 97 95 17 6 15 135 30 40 65 1×10 11

XAD 1069 210 166.0 0.79 96 – 17 – – – – – – –

Front: 1×1012
FGS 130 130 100.1 0.77 97 96 18 7 20 135 30 50 90 1×10 11
WESC 165 162 143.0 0.88 90 3/97 109/15 – – – – – – Back: 1×1011

FGS 150 150 115.5 0.77 97 96 18 8 20 135 30 65 125 1×10 11

WEJ 200 200 160.0 0.80 93 95 2/18 – – – – – – 1×1010

FGS 200 200 158.0 0.79 97 98 19 10 30 150 30 125 230 1×1011 WESA 165 164 140.0 0.87 96 87 16/16 – – – – – – 1×1011

FGS 250 250 200.0 0.80 96 99 19 10 35 160 30 195 300< 1×1011 WNF 135 134 101.2 0.75 96 60 17/5 9 16 51 23 44 59 9×1011>

FGS 300 300 234.0 0.78 96 99 19 9 35 130 30 270 300< 1×1011 WNFW 200 201 155.0 0.78 96 96 17/17 12 25 56 26 13 205 9×1011>

Physical Properties
FEB 95 95 73.2 0.77 98 96 49 5 15 130 30 35 65 1×1011 WMF 120 123 106.3 0.86 –/95 100 100</16 8 18 105 23 68 107 9×1011>

FEB 110 110 84.7 0.77 98 97 50 6 15 125 30 45 85 1×1011 WSF 110 107 70.0 0.65 96 88 10/16 4 8 80 18 13 23 9×1011>

FEB 130 130 100.1 0.77 98 98 48 7 20 130 30 60 115 1×10 11

WSF 160 159 110.0 0.65 95 94 10/17 7 16 125 21 33 72 9×1011>

FEB 150 150 115.5 0.77 98 98 49 7 20 135 25 75 155 1×1011 WCFA 125 123 104.0 0.83 88 100 16 7 19 135 33 46 89 9×1011>

FEB 200 200 158.0 0.79 98 99 48 10 30 135 25 130 270 1×1011 WCFA 195 190 150.0 0.82 91 100 18 10 25 150 26 109 210 9×1011>

FEB 250 250 200.0 0.80 98 99 46 10 35 120 30 210 300< 1×1011 VJFP 120 115 78.0 0.68 96 – 2 – – – – – – –

FEBA 300 300 234.0 0.78 97 99 46 10 35 100 30 280 300< 1×10 11

VJFP 170 165 117.5 0.71 101 93 2/17 – – – – – – –

FRB 110 110 88.0 0.80 98 96 53/24 4 15 90 30 45 80 1×10 11

XAB 1020 135 90.0 0.67 92 95 2/17 – – – – – – –

FRB 130 130 102.7 0.79 98 97 53/24 5 15 95 30 60 110 1×10 10

VJFN 160 160 135.0 0.84 97 96 37/16 – – – – – – –

Front: 1×1012
FRR 70 70 56.7 0.81 98 91 49/21 3 10 120 25 20 35 Back: 1×1011 YPI 150 150 115.5 0.77 97 96 11/10 8 20 140 30 65 125 1×1010

TPRA 60 60 60.6 1.01 92 30 13 4 9 185 40 15 15 1×1011 YPI 200 200 158.0 0.79 97 98 13/11 10 30 150 30 120 230 1×1010

TPAR 90 90 91.8 1.02 92 40 15 6 15 200 40 30 40 1×1011 YPI 250 250 200.0 0.80 96 99 14/12 10 35 160 30 180 300< 1×1010

BLR 150 150 153.0 1.02 93 63 15 10 30 210 40 80 130 1×1011 YPI 300 300 234.0 0.78 96 99 14/11 9 35 130 30 300 300< 1×1010

BCR 160 160 153.0 0.96 94 63 34 10 30 200 35 95 170 1×10 11

FPU 130 130 100.1 0.77 97 96 17 7 20 140 30 50 110 1×1011

QJJ 350 350 340.0 0.97 95 98 20 – – – – 300< 300< 1×1011 FPU 200 200 158.0 0.79 97 98 17 10 30 155 30 130 260 1×1011

QJJ 400 400 390.0 0.98 95 98 20 – – – – 300< 300< 1×1011 FPU 250 250 200.0 0.80 97 99 16 10 35 165 30 200 300< 1×1011

QJJ 500 500 494.0 0.99 95 98 19 – – – – 300< 300< 1×1011 Measurement JIS JIS JIS JIS JIS JIS JIS JIS JIS JIS
method P 8118 P 8124 P 8118 L 1015 P 8149 P 8142 P 8113 P 8113 P 8143 K 6911

QTYR 350 350 353.0 1.01 93 96 89/18 – – – – 300< 300< 1×1011 WESC 165 has a transparent face with a YUPO backing.

RMM 400 400 396.0 0.99 93 78 13 – – – – 300< 300< 1×1011

SGS 60 60 48.6 0.81 97 85 22/54 3 10 120 25 10 25 1×1011

SGS 80 80 66.4 0.83 97 89 22/53 5 15 125 25 20 50 1×1011

SGS 110 110 91.3 0.83 97 93 22/52 6 20 130 25 35 90 1×1011 Caliper: Range from 60 μm (0.06 mm) to 500 μm (0.5 mm). Clark stiffness: The greater the value, the greater the stiffness.
Density: The density of most products is below 1 g/ . Surface resistance: The lower the value, the less generation of
SGP 80 80 66.4 0.83 97 89 4/6 5 15 125 25 20 50 1×1011
They are light enough to float on water. static electricity. (PP has more than 10 15£
SGP 110 110 91.3 0.83 97 93 6/7 6 20 130 25 35 90 1×1011 Whiteness: The greater the value, the whiter the product.
Opacity: Products for which the value is 100% are completely opaque.
Front: 1×1012
LAR 75 75 60.8 0.81 98 95 36/26 3 10 115 25 15 35 Back: 1×1015 Gloss: The greater the value, the glossier the printing finish.
Front: 1×1012 Tensile strength: This is the maximum load that can be applied to the MD
LAR 95 95 76.5 0.81 98 96 38/26 5 15 125 25 30 55 Back: 1×1015 (machine direction) and CD (cross direction).
* Values are representative examples of measurements taken by YUPO.
We do not guarantee the accuracy of stated values.
Measurement JIS JIS JIS JIS JIS JIS JIS JIS JIS JIS Elongation: The amount of elongation that will occur before giving way * Tests were conducted according to the standards listed.
method P 8118 P 8124 P 8118 L 1015 P 8149 P 8142 P 8113 P 8113 P 8143 K 6911 when stretched. * The optical system used to test opacity is compliant with JIS Z 8722.

25 26