Caliber 12
Uploaded by
ScribdTranslationsCaliber 12
Uploaded by
ScribdTranslationsUNCONVENTIONAL ARMAMENT
Subject: 12 Gauge Shotgun
OBJECTIVES
Know the characteristics of
12 Gauge Shotguns
Carry out assembly and disassembly
in 1st Tier
Manage the Weaponry
SUMMARY
I–INTRODUCTION
II–DEVELOPMENT
12 Gauge Shotgun
• Presentation (Features)
• Dismantling of 1st Level
• Assembly of 1st Tier
• Management
INTRODUCTION
• Special Characteristics of
12 Gauge Shotgun
12 gauge shotgun
• The models used are:
CBC shotgun model 586-2
Shotgun BOITO model BSA-5T-84.
• Common characteristics of shotguns
cited:
caliber 12;
multiplicity of cartridges that can be -
used (balloons, rubber or gas ballots
tear gas)
large shooting capacity;
pump action repetition system;
long canoe
double security system.
12 GAUGE SHOTGUN
BOITO SHOTGUN MODEL BSA-5T-84
PUMP ACTION
The Unit has BOITO shotguns.
BSA-5T-84 model, extremely weapons
well built and robust.
Its mechanism differs, with some
advantages and disadvantages of CBC-586
but, in essence, its functioning is the
even, as well as its practical application.
Enables joint use of lethal ammunition and
non-lethal.
12 CALIBER BOITO SHOTGUN
MODEL BSA-5T-84 "PUMP ACTION"
12 GAUGE SHOTGUN
PRESENTATION
Numeric reference does not have
Military Indicative Does not have
Nomenclature 12 Gauge Shotgun
BOITO Mod BSA-5T-84
12 gauge shotgun
CHARACTERISTICS
a) Classifying aspects
Regarding the type Of Door
Regarding employment Individual
Motor principle Muscle action of the shooter
As for the operation From repetition, by bomb action
Regarding the Loading Recharge
Raying Smooth edge (internal polishing)
Caliber 12
Sighting device Spherical mass in all versions
Raying Smooth edge (internal polishing)
As for the system of The air
refrigeration
12-Gauge Shotgun
CHARACTERISTICS
b) Numerical Data
Weight 1.9 kg
Scope Undefined
maximum
Useful range Varies with the ammunition
Length 1.0 m
total
Length 47 cm (Adjustable)
of the canoe
12 CALIBER SHOTGUN
CHARACTERISTICS
c) Food
Charger Tubular, under the pipe
Quanto ao Carregamento Retrocarga
Shooting capacity 8 cartridges (7 + 1)
12 GAUGE SHOTGUN
DISMANTLING OF 1ST STAGE
Needs a nail puller and a rubber hammer.
Preliminary Measures
Execute two security blows. Acting on
handguard
The weapon must be open
Lock the weapon in the safety lock that is on the
top of the block.
– Certify that there is no ammunition in the chamber and not
so little in the cartridge holder.
12-Gauge Shotgun
DISMANTLING OF 1ST STAGE
1) With the weapon in the vertical position, the should be unscrewed.
pipe fastening screw; (acting on the screw
of fixing the pipe, unscrewing it in the direction
counterclockwise.
2) Remove the pipe set; (suspend the pipe,
unclipping it from the buttstock).
3) Remove the pin that secures the external trigger; (with the
help of a punch and a rubber mallet,
affect touch on the fixing pin on the right side of
weapon).
4) Remove the mudguard set; (acting on the guard-
mato, will suspend the previous part (set
(crown) towards the handguard.
5) Remove the cartridge release (right side),
(unclamp it from its housing with the
thumb assistance.
12 CALIBER SHOTGUN
DISMANTLING OF 1ST STAGE
Remove the limiting arm from the cartridges (left side)
it has a round hole in its middle part;
(unclip it from its housing at the butt with the
finger assistance.
7) Remove the central latch guide; (with the help of your finger,
place it in the middle part of the butt and remove it with the
index and thumb fingers.
8) Remove the handguard; (push the handguard,
unclipping it from the stock).
9) Remove the central latch; with the help of the indicator,
take the central latch to the fitting hole and
unblock the pipe).
10) Remove the feeder from the cartridges; (with the help of
indicator to suspend the existing protrusion in the part
the back of the cartridge feeder and press
your stems slightly inward, removing it from the
guide pins).
12 gauge shotgun
ORDER OF PARTS AFTER DISASSEMBLY
OF 1ST LEVEL
• Pipe fastening screw
• Pipe set
• External trigger pin
• Set of guard-mato
• Cartridge limiting arm
• Cartridge release
• Central latch guide and lock actuator
bolt
• Hand guard
• Central latch
• Cartridge feeder
• Set of buttstock and cartridge holder cylinder
12 gauge shotgun
12 gauge shotgun
MONTAGEM DE 1º ESCALÃO
Here is the reverse sequence of
first stage disassembly (from the right
to the left)
Note: In the assembly of the feeder of the
cartridges with protruding lead
the holes should face upwards.
12 gauge shotgun
MANAGEMENT
a) Feed the weapon
To make a single cartridge shot.
Aim the weapon and keep it pointed at a
safe direction.
Pull the handrail until it opens completely
EJECTION WINDOW.
If the weapon is cocked, it will be necessary
press the bolt release in advance.
-Place the cartridge through the eject window; if not
it is necessary to fully insert it into the chamber.
-Push the handguard forward to introduce the
cartridge in the chamber and close the mechanism.
-To fire it, it will be necessary to press the button of the
move forward, so that the red point
be visible. The weapon is now ready to fire.
12 gauge shotgun
DOOR RELEASE
12 gauge shotgun
Management
b) To load the chamber and the cylinder
cartridge holder
Repeat the operations from one to four.
To feed the cartridge holder cylinder
position the weapon in a way that makes it easy to
access from the bottom feeding window. With
the end of the cartridge, press the spring of the
cylinder, in order to introduce it
completely, ensuring that the edge
the cartridge has entered beyond the release
two cartridges.
12 Gauge Shotgun
MANAGEMENT
c) Shoot
• Unlock the weapon, pull the trigger, and fire the weapon.
d) To fire the weapon again
• Pull the handguard without twisting it to eject the cartridge.
empty.
• Push the handrail forward to introduce new
cartridge in the chamber.
e) To unload the weapon without firing
• Point the weapon in a safe direction vertically and
make sure it is locked.
• Press and hold the central bolt release.
• Pull and push the handrail successively, in order to
extract the cartridge from the chamber, eject it through the ejection window,
insert a new cartridge into the chamber until all the
cartridges have been extracted. Make sure that none
the cartridge remained in the chamber or in the cylinder holder
cartridges.
12 GAUGE SHOTGUN
safety lock
12-Gauge Shotgun
e) Incidents
Immediate action:
Keep the weapon in shooting position;
Ensure that the mechanism remains in
your posterior position (closed);
Place the safety register in the position of
security
Open the weapon, acting on the handguard to
eject the existing cartridge from the chamber;
Close the bolt mechanism to load the
weapon
Place the safety lock in the position of
fire
Restart the shot.
CONCLUSION
Questions
