Project Job no.

Calcs for Start page no./Revision

DESIGN INN
1
Calcs by Calcs date Checked by Checked date Approved by Approved date

G 12/21/2025

Story Heights ( Total 16’)

Ceiling Floor 8

Top Floor 8

Member Size

Rafter 2x6

Rafter 2x8

Bridge Beam 2x8

Support 4x6 (2-2x6)

 Project Job no.

Calcs for Start page no./Revision

DESIGN INN
2
Calcs by Calcs date Checked by Checked date Approved by Approved date

G 12/21/2025

Load Type Value (Psf)

Dead Load 30

Live Load 50

RAFTER 2X8 DOUGHLAS FIR

In accordance with the ANSI/AF&PA NDS 2018 using the LRFD method
Tedds calculation version 2.2.22

Design summary
Overall design utilisation; 0.492
Overall design status; PASS

Dead results summary Unit Capacity Maximum Utilization Result

Bending stress lb/in2 1099 457 0.415 PASS
Shear stress lb/in2 233 14 0.059 PASS
Live results summary Unit Capacity Maximum Utilization Result
Bending stress lb/in2 1895 731 0.385 PASS
Shear stress lb/in2 311 28 0.089 PASS
Total long term deflection - C#3 results Unit Capacity Maximum Utilization Result
summary
Deflection in 0.8 0.394 0.492 PASS
Dead load deflection - C#3 results Unit Capacity Maximum Utilization Result
summary
Deflection in 0.533 0.166 0.312 PASS
Live load deflection - C#3 results Unit Capacity Maximum Utilization Result
summary
Deflection in 0.533 0.124 0.232 PASS

Dead
Member details
Service condition; Dry
Sawn lumber section details
Number of sections in member; N=1
Nominal breadth of sections; bnom = 2 in
Breadth of sections; b = 1.5 in
Nominal depth of sections; dnom = 8 in
Depth of sections; d = 7.25 in
Material; Douglas Fir-Larch, 2'' && wider, Select Structural grade
 Project Job no.

Calcs for Start page no./Revision

DESIGN INN
3
Calcs by Calcs date Checked by Checked date Approved by Approved date

G 12/21/2025

Span details
Unbraced length - Major axis; Lx = 16 ft
Effective bending length - Major axis; Le,x = 1.63  Lx + 3  b = 26.455 ft
Column buckling length - Major axis; Lb,x = Lx = 16 ft
Unbraced length - Minor axis; Ly = 16 ft
Effective bending length - Minor axis; Le,y = 1.63  Ly + 3  d = 27.892 ft
Column buckling length - Minor axis; Lb,y = Ly = 16 ft
Bearing length; Lb = 4 in
Analysis results
Design bending moment - Major axis; Mx = 500 lb_ft
Design shear force - Major axis; Vx = 100 lb
Adjustment factors - Table 4.3.1
Size factor for bending - Table 4A; CFb = 1.2
Depth-to-breadth ratio; dnom / bnom = 4.00
Slenderness ratio - eq.3.3-5; RB = (Le,y  d / b2) = 32.841
Reference bending design value; Fb = Fb  CFb  KFb  b   = 2332 lb/in2
Adjusted modulus of elasticity; Emin' = Emin  KFE  s = 1032240 lb/in2
Critical buckling design value - cl.[Link]; FbE = 1.2  Emin' / RB2 = 1149 lb/in2
Beam stability factor - eq.3.3-6
CL = [1 + (FbE / Fb)] / 1.9 - [([1 + (FbE / Fb)] / 1.9)2 - (FbE / Fb) / 0.95] = 0.472
Format conversion factor for bending - Table 2.3.5; KFb = 2.54
Format conversion factor for shear - Table 2.3.5; KFv = 2.88
Resistance factor for bending - Table 2.3.6; b = 0.85
Resistance factor for shear - Table 2.3.6; v = 0.75
Time effect factor - Table N.3;  = 0.6
 Project Job no.

Calcs for Start page no./Revision

DESIGN INN
4
Calcs by Calcs date Checked by Checked date Approved by Approved date

G 12/21/2025

Bending members - Flexure - cl.3.3

Design bending moment; Mx = 500 lb_ft
Design bending stress - Table 4.3.1; Fb,x' = Fb  CL  CFb  KFb  b   = 1099 lb/in2
Actual bending stress - eq.3.3-2; fb,x = Mx / Sx = 457 lb/in2
fb,x / Fb,x' = 0.415
PASS - Design bending stress exceeds actual bending stress
Bending members - Shear - cl.3.4
Design shear force; Vx = 100 lb
Design shear stress - Table 4.3.1; Fv,x' = Fv  KFv  v   = 233 lb/in2
Actual shear stress - eq.3.4-2; fv,x = 3  Vx / (2  b  d) = 14 lb/in2
fv,x / Fv,x' = 0.059
PASS - Design shear stress exceeds actual shear stress

Live
Member details
Service condition; Dry
Sawn lumber section details
Number of sections in member; N=1
Nominal breadth of sections; bnom = 2 in
Breadth of sections; b = 1.5 in
Nominal depth of sections; dnom = 8 in
Depth of sections; d = 7.25 in
Material; Douglas Fir-Larch, 2'' && wider, Select Structural grade

Span details
Unbraced length - Major axis; Lx = 16 ft
Effective bending length - Major axis; Le,x = Lx = 16 ft
Column buckling length - Major axis; Lb,x = Lx = 16 ft
 Project Job no.

Calcs for Start page no./Revision

DESIGN INN
5
Calcs by Calcs date Checked by Checked date Approved by Approved date

G 12/21/2025

Unbraced length - Minor axis; Ly = 16 ft

Effective bending length - Minor axis; Le,y = Ly = 16 ft
Column buckling length - Minor axis; Lb,y = Ly = 16 ft
Bearing length; Lb = 4 in
Analysis results
Design bending moment - Major axis; Mx = 800 lb_ft
Design shear force - Major axis; Vx = 200 lb
Adjustment factors - Table 4.3.1
Size factor for bending - Table 4A; CFb = 1.2
Repetitive member factor - Table 4.3.9; Cr = 1.15
Depth-to-breadth ratio; dnom / bnom = 4.00
Slenderness ratio - eq.3.3-5; RB = (Le,y  d / b2) = 24.873
Reference bending design value; Fb = Fb  CFb  Cr  KFb  b   = 3575 lb/in2
Adjusted modulus of elasticity; Emin' = Emin  KFE  s = 1032240 lb/in2
Critical buckling design value - cl.[Link]; FbE = 1.2  Emin' / RB2 = 2002 lb/in2
Beam stability factor - eq.3.3-6
CL = [1 + (FbE / Fb)] / 1.9 - [([1 + (FbE / Fb)] / 1.9)2 - (FbE / Fb) / 0.95] = 0.53
Format conversion factor for bending - Table 2.3.5; KFb = 2.54
Format conversion factor for shear - Table 2.3.5; KFv = 2.88
Resistance factor for bending - Table 2.3.6; b = 0.85
Resistance factor for shear - Table 2.3.6; v = 0.75
Time effect factor - Table N.3;  = 0.8

Bending members - Flexure - cl.3.3

Design bending moment; Mx = 800 lb_ft
Design bending stress - Table 4.3.1; Fb,x' = Fb  CL  CFb  Cr  KFb  b   = 1895 lb/in2
Actual bending stress - eq.3.3-2; fb,x = Mx / Sx = 731 lb/in2
fb,x / Fb,x' = 0.385
PASS - Design bending stress exceeds actual bending stress
Bending members - Shear - cl.3.4
Design shear force; Vx = 200 lb
Design shear stress - Table 4.3.1; Fv,x' = Fv  KFv  v   = 311 lb/in2
Actual shear stress - eq.3.4-2; fv,x = 3  Vx / (2  b  d) = 28 lb/in2
fv,x / Fv,x' = 0.089
PASS - Design shear stress exceeds actual shear stress

Total long term deflection - C#3

Member details
Service condition; Dry
Sawn lumber section details
Number of sections in member; N=1
Nominal breadth of sections; bnom = 2 in
Breadth of sections; b = 1.5 in
Nominal depth of sections; dnom = 8 in
 Project Job no.

Calcs for Start page no./Revision

DESIGN INN
6
Calcs by Calcs date Checked by Checked date Approved by Approved date

G 12/21/2025

Depth of sections; d = 7.25 in

Material; Douglas Fir-Larch, 2'' && wider, Select Structural grade

Span details
Span length; Ls = 16 ft
Analysis results
Deflection - Major axis; x = 0.29 in

Adjustment factors - Table 4.3.1

Repetitive member factor - Table 4.3.9; Cr = 1.15
Time dependent deformation factor - cl.3.5.2; Kcr = 1.5
Bending members - Deflection - cl.3.5
Instantaneous deflection; x = 0.29 in
Final deflection; x,Final = Kcr  0.714  x + 0.286  x = 0.394 in
Allowable deflection; x,Allowable = Ls / 240 = 0.8 in
x,Final / x,Allowable = 0.492
PASS - Allowable deflection exceeds final deflection

Dead load deflection - C#3

Member details
Service condition; Dry
Sawn lumber section details
Number of sections in member; N=1
Nominal breadth of sections; bnom = 2 in
Breadth of sections; b = 1.5 in
Nominal depth of sections; dnom = 8 in
Depth of sections; d = 7.25 in
Material; Douglas Fir-Larch, 2'' && wider, Select Structural grade
 Project Job no.

Calcs for Start page no./Revision

DESIGN INN
7
Calcs by Calcs date Checked by Checked date Approved by Approved date

G 12/21/2025

Span details
Span length; Ls = 16 ft
Analysis results
Deflection - Major axis; x = 0.166 in

Bending members - Deflection - cl.3.5

Instantaneous deflection; x = 0.166 in
Allowable deflection; x,Allowable = Ls / 360 = 0.533 in
x / x,Allowable = 0.312
PASS - Allowable deflection exceeds instantaneous deflection

Live load deflection - C#3

Member details
Service condition; Dry
Sawn lumber section details
Number of sections in member; N=1
Nominal breadth of sections; bnom = 2 in
Breadth of sections; b = 1.5 in
Nominal depth of sections; dnom = 8 in
Depth of sections; d = 7.25 in
Material; Douglas Fir-Larch, 2'' && wider, Select Structural grade
 Project Job no.

Calcs for Start page no./Revision

DESIGN INN
8
Calcs by Calcs date Checked by Checked date Approved by Approved date

G 12/21/2025

Span details
Span length; Ls = 16 ft
Analysis results
Deflection - Major axis; x = 0.124 in

Bending members - Deflection - cl.3.5

Instantaneous deflection; x = 0.124 in
Allowable deflection; x,Allowable = Ls / 360 = 0.533 in
x / x,Allowable = 0.232
PASS - Allowable deflection exceeds instantaneous deflection
 Project Job no.

Calcs for Start page no./Revision

DESIGN INN
9
Calcs by Calcs date Checked by Checked date Approved by Approved date

G 12/21/2025

RAFTER 2X6 DOUGHLAS FIR

In accordance with the ANSI/AF&PA NDS 2018 using the LRFD method
Tedds calculation version 2.2.22

Design summary
Overall design utilisation; 0.556
Overall design status; PASS

Dead results summary Unit Capacity Maximum Utilization Result

Bending stress lb/in2 1442 317 0.220 PASS
Shear stress lb/in2 233 18 0.078 PASS
Live results summary Unit Capacity Maximum Utilization Result
Bending stress lb/in2 2434 635 0.261 PASS
Shear stress lb/in2 311 18 0.058 PASS
Total long term deflection - C#3 results Unit Capacity Maximum Utilization Result
summary
Deflection in 0.8 0.445 0.556 PASS
Dead load deflection - C#3 results Unit Capacity Maximum Utilization Result
summary
Deflection in 0.533 0.199 0.373 PASS
Live load deflection - C#3 results Unit Capacity Maximum Utilization Result
summary
Deflection in 0.533 0.125 0.235 PASS

Dead
Member details
Service condition; Dry
Sawn lumber section details
Number of sections in member; N=1
Nominal breadth of sections; bnom = 2 in
Breadth of sections; b = 1.5 in
Nominal depth of sections; dnom = 6 in
Depth of sections; d = 5.5 in
Material; Douglas Fir-Larch, 2'' && wider, Select Structural grade
 Project Job no.

Calcs for Start page no./Revision

DESIGN INN
10
Calcs by Calcs date Checked by Checked date Approved by Approved date

G 12/21/2025

Span details
Unbraced length - Major axis; Lx = 16 ft
Effective bending length - Major axis; Le,x = 1.63  Lx + 3  b = 26.455 ft
Column buckling length - Major axis; Lb,x = Lx = 16 ft
Unbraced length - Minor axis; Ly = 16 ft
Effective bending length - Minor axis; Le,y = 1.63  Ly + 3  d = 27.455 ft
Column buckling length - Minor axis; Lb,y = Ly = 16 ft
Bearing length; Lb = 4 in
Analysis results
Design bending moment - Major axis; Mx = 200 lb_ft
Design shear force - Major axis; Vx = 100 lb
Adjustment factors - Table 4.3.1
Size factor for bending - Table 4A; CFb = 1.3
Depth-to-breadth ratio; dnom / bnom = 3.00
Slenderness ratio - eq.3.3-5; RB = (Le,y  d / b2) = 28.379
Reference bending design value; Fb = Fb  CFb  KFb  b   = 2526 lb/in2
Adjusted modulus of elasticity; Emin' = Emin  KFE  s = 1032240 lb/in2
Critical buckling design value - cl.[Link]; FbE = 1.2  Emin' / RB2 = 1538 lb/in2
Beam stability factor - eq.3.3-6
CL = [1 + (FbE / Fb)] / 1.9 - [([1 + (FbE / Fb)] / 1.9)2 - (FbE / Fb) / 0.95] = 0.571
Format conversion factor for bending - Table 2.3.5; KFb = 2.54
Format conversion factor for shear - Table 2.3.5; KFv = 2.88
Resistance factor for bending - Table 2.3.6; b = 0.85
Resistance factor for shear - Table 2.3.6; v = 0.75
Time effect factor - Table N.3;  = 0.6
 Project Job no.

Calcs for Start page no./Revision

DESIGN INN
11
Calcs by Calcs date Checked by Checked date Approved by Approved date

G 12/21/2025

Bending members - Flexure - cl.3.3

Design bending moment; Mx = 200 lb_ft
Design bending stress - Table 4.3.1; Fb,x' = Fb  CL  CFb  KFb  b   = 1442 lb/in2
Actual bending stress - eq.3.3-2; fb,x = Mx / Sx = 317 lb/in2
fb,x / Fb,x' = 0.220
PASS - Design bending stress exceeds actual bending stress
Bending members - Shear - cl.3.4
Design shear force; Vx = 100 lb
Design shear stress - Table 4.3.1; Fv,x' = Fv  KFv  v   = 233 lb/in2
Actual shear stress - eq.3.4-2; fv,x = 3  Vx / (2  b  d) = 18 lb/in2
fv,x / Fv,x' = 0.078
PASS - Design shear stress exceeds actual shear stress

Live
Member details
Service condition; Dry
Sawn lumber section details
Number of sections in member; N=1
Nominal breadth of sections; bnom = 2 in
Breadth of sections; b = 1.5 in
Nominal depth of sections; dnom = 6 in
Depth of sections; d = 5.5 in
Material; Douglas Fir-Larch, 2'' && wider, Select Structural grade

Span details
Unbraced length - Major axis; Lx = 16 ft
Effective bending length - Major axis; Le,x = Lx = 16 ft
Column buckling length - Major axis; Lb,x = Lx = 16 ft
 Project Job no.

Calcs for Start page no./Revision

DESIGN INN
12
Calcs by Calcs date Checked by Checked date Approved by Approved date

G 12/21/2025

Unbraced length - Minor axis; Ly = 16 ft

Effective bending length - Minor axis; Le,y = Ly = 16 ft
Column buckling length - Minor axis; Lb,y = Ly = 16 ft
Bearing length; Lb = 4 in
Analysis results
Design bending moment - Major axis; Mx = 400 lb_ft
Design shear force - Major axis; Vx = 100 lb
Adjustment factors - Table 4.3.1
Size factor for bending - Table 4A; CFb = 1.3
Repetitive member factor - Table 4.3.9; Cr = 1.15
Depth-to-breadth ratio; dnom / bnom = 3.00
Slenderness ratio - eq.3.3-5; RB = (Le,y  d / b2) = 21.664
Reference bending design value; Fb = Fb  CFb  Cr  KFb  b   = 3873 lb/in2
Adjusted modulus of elasticity; Emin' = Emin  KFE  s = 1032240 lb/in2
Critical buckling design value - cl.[Link]; FbE = 1.2  Emin' / RB2 = 2639 lb/in2
Beam stability factor - eq.3.3-6
CL = [1 + (FbE / Fb)] / 1.9 - [([1 + (FbE / Fb)] / 1.9)2 - (FbE / Fb) / 0.95] = 0.628
Format conversion factor for bending - Table 2.3.5; KFb = 2.54
Format conversion factor for shear - Table 2.3.5; KFv = 2.88
Resistance factor for bending - Table 2.3.6; b = 0.85
Resistance factor for shear - Table 2.3.6; v = 0.75
Time effect factor - Table N.3;  = 0.8

Bending members - Flexure - cl.3.3

Design bending moment; Mx = 400 lb_ft
Design bending stress - Table 4.3.1; Fb,x' = Fb  CL  CFb  Cr  KFb  b   = 2434 lb/in2
Actual bending stress - eq.3.3-2; fb,x = Mx / Sx = 635 lb/in2
fb,x / Fb,x' = 0.261
PASS - Design bending stress exceeds actual bending stress
Bending members - Shear - cl.3.4
Design shear force; Vx = 100 lb
Design shear stress - Table 4.3.1; Fv,x' = Fv  KFv  v   = 311 lb/in2
Actual shear stress - eq.3.4-2; fv,x = 3  Vx / (2  b  d) = 18 lb/in2
fv,x / Fv,x' = 0.058
PASS - Design shear stress exceeds actual shear stress

Total long term deflection - C#3

Member details
Service condition; Dry
Sawn lumber section details
Number of sections in member; N=1
Nominal breadth of sections; bnom = 2 in
Breadth of sections; b = 1.5 in
Nominal depth of sections; dnom = 6 in
 Project Job no.

Calcs for Start page no./Revision

DESIGN INN
13
Calcs by Calcs date Checked by Checked date Approved by Approved date

G 12/21/2025

Depth of sections; d = 5.5 in

Material; Douglas Fir-Larch, 2'' && wider, Select Structural grade

Span details
Span length; Ls = 16 ft
Analysis results
Deflection - Major axis; x = 0.324 in

Adjustment factors - Table 4.3.1

Repetitive member factor - Table 4.3.9; Cr = 1.15
Time dependent deformation factor - cl.3.5.2; Kcr = 1.5
Bending members - Deflection - cl.3.5
Instantaneous deflection; x = 0.324 in
Final deflection; x,Final = Kcr  0.741  x + 0.259  x = 0.445 in
Allowable deflection; x,Allowable = Ls / 240 = 0.8 in
x,Final / x,Allowable = 0.556
PASS - Allowable deflection exceeds final deflection

Dead load deflection - C#3

Member details
Service condition; Dry
Sawn lumber section details
Number of sections in member; N=1
Nominal breadth of sections; bnom = 2 in
Breadth of sections; b = 1.5 in
Nominal depth of sections; dnom = 6 in
Depth of sections; d = 5.5 in
Material; Douglas Fir-Larch, 2'' && wider, Select Structural grade
 Project Job no.

Calcs for Start page no./Revision

DESIGN INN
14
Calcs by Calcs date Checked by Checked date Approved by Approved date

G 12/21/2025

Span details
Span length; Ls = 16 ft
Analysis results
Deflection - Major axis; x = 0.199 in

Bending members - Deflection - cl.3.5

Instantaneous deflection; x = 0.199 in
Allowable deflection; x,Allowable = Ls / 360 = 0.533 in
x / x,Allowable = 0.373
PASS - Allowable deflection exceeds instantaneous deflection

Live load deflection - C#3

Member details
Service condition; Dry
Sawn lumber section details
Number of sections in member; N=1
Nominal breadth of sections; bnom = 2 in
Breadth of sections; b = 1.5 in
Nominal depth of sections; dnom = 6 in
Depth of sections; d = 5.5 in
Material; Douglas Fir-Larch, 2'' && wider, Select Structural grade
 Project Job no.

Calcs for Start page no./Revision

DESIGN INN
15
Calcs by Calcs date Checked by Checked date Approved by Approved date

G 12/21/2025

Span details
Span length; Ls = 16 ft
Analysis results
Deflection - Major axis; x = 0.125 in

Bending members - Deflection - cl.3.5

Instantaneous deflection; x = 0.125 in
Allowable deflection; x,Allowable = Ls / 360 = 0.533 in
x / x,Allowable = 0.235
PASS - Allowable deflection exceeds instantaneous deflection

4X6(2-2X6) SUPPORT
In accordance with the ANSI/AF&PA NDS 2018 using the LRFD method
Tedds calculation version 2.2.22

Design summary
Overall design utilisation; 0.02
Overall design status; PASS

Dead results summary Unit Capacity Maximum Utilization Result

Compressive stress lb/in2 991 16 0.016 PASS
Live results summary Unit Capacity Maximum Utilization Result
Compressive stress lb/in2 1031 21 0.020 PASS
 Project Job no.

Calcs for Start page no./Revision

DESIGN INN
16
Calcs by Calcs date Checked by Checked date Approved by Approved date

G 12/21/2025

Dead
Member details
Service condition; Dry
Sawn lumber section details
Number of sections in member; N=1
Nominal breadth of sections; bnom = 4 in
Breadth of sections; b = 3.5 in
Nominal depth of sections; dnom = 6 in
Depth of sections; d = 5.5 in
Material; Douglas Fir-Larch, 2'' && wider, Select Structural grade

Span details
Unbraced length - Major axis; Lx = 8 ft
Effective bending length - Major axis; Le,x = 1.63  Lx + 3  b = 13.915 ft
Column buckling length - Major axis; Lb,x = Lx = 8 ft
Unbraced length - Minor axis; Ly = 8 ft
Effective bending length - Minor axis; Le,y = 1.63  Ly + 3  d = 14.415 ft
Column buckling length - Minor axis; Lb,y = Ly = 8 ft
Analysis results
Design axial compression force; P = 300 lb
Adjustment factors - Table 4.3.1
Size factor for compression - Table 4A; CFc = 1.1
Reference compression design value; Fc = Fc  CFc  KFc  c   = 2424 lb/in2
Adjusted modulus of elasticity; Emin' = Emin  KFE  s = 1032240 lb/in2
Critical buckling design value; FcE = 0.822  Emin' / (Lb,y / b)2 = 1128 lb/in2
Column stability factor - eq.3.7-1
CP = (1 + (FcE / Fc)) / 1.6 - (((1 + (FcE / Fc)) / 1.6)2 - (FcE / Fc) / 0.8) = 0.409
Format conversion factor for comp. - Table 2.3.5; KFc = 2.4
[Link] for [Link] elasticity - Table 2.3.5; KFE = 1.76
 Project Job no.

Calcs for Start page no./Revision

DESIGN INN
17
Calcs by Calcs date Checked by Checked date Approved by Approved date

G 12/21/2025

Resistance factor for compression - Table 2.3.6; c = 0.9

Resistance factor for [Link] elasticity - Table 2.3.6; s = 0.85
Time effect factor - Table N.3;  = 0.6

Compression members - General - cl.3.6

Design axial compression force; P = 300 lb
Design compression parallel to grain - Table 4.3.1; Fc' = Fc  CFc  CP  KFc  c   = 991 lb/in2
Actual compression parallel to grain; fc = P / (b  d) = 16 lb/in2
fc / Fc' = 0.016
PASS - Design compression stress exceeds actual compression stress

Live
Member details
Service condition; Dry
Sawn lumber section details
Number of sections in member; N=1
Nominal breadth of sections; bnom = 4 in
Breadth of sections; b = 3.5 in
Nominal depth of sections; dnom = 6 in
Depth of sections; d = 5.5 in
Material; Douglas Fir-Larch, 2'' && wider, Select Structural grade

Span details
Unbraced length - Major axis; Lx = 8 ft
Effective bending length - Major axis; Le,x = Lx = 8 ft
Column buckling length - Major axis; Lb,x = Lx = 8 ft
Unbraced length - Minor axis; Ly = 8 ft
Effective bending length - Minor axis; Le,y = Ly = 8 ft
Column buckling length - Minor axis; Lb,y = Ly = 8 ft
 Project Job no.

Calcs for Start page no./Revision

DESIGN INN
18
Calcs by Calcs date Checked by Checked date Approved by Approved date

G 12/21/2025

Analysis results
Design axial compression force; P = 400 lb
Adjustment factors - Table 4.3.1
Size factor for compression - Table 4A; CFc = 1.1
Repetitive member factor - Table 4.3.9; Cr = 1.15
Reference compression design value; Fc = Fc  CFc  KFc  c   = 3231 lb/in2
Adjusted modulus of elasticity; Emin' = Emin  KFE  s = 1032240 lb/in2
Critical buckling design value; FcE = 0.822  Emin' / (Lb,y / b)2 = 1128 lb/in2
Column stability factor - eq.3.7-1
CP = (1 + (FcE / Fc)) / 1.6 - (((1 + (FcE / Fc)) / 1.6)2 - (FcE / Fc) / 0.8) = 0.319
Format conversion factor for comp. - Table 2.3.5; KFc = 2.4
[Link] for [Link] elasticity - Table 2.3.5; KFE = 1.76
Resistance factor for compression - Table 2.3.6; c = 0.9
Resistance factor for [Link] elasticity - Table 2.3.6; s = 0.85
Time effect factor - Table N.3;  = 0.8

Compression members - General - cl.3.6

Design axial compression force; P = 400 lb
Design compression parallel to grain - Table 4.3.1; Fc' = Fc  CFc  CP  KFc  c   = 1031 lb/in2
Actual compression parallel to grain; fc = P / (b  d) = 21 lb/in2
fc / Fc' = 0.020
PASS - Design compression stress exceeds actual compression stress

2X6 RAFTER
In accordance with the ANSI/AF&PA NDS 2018 using the LRFD method
Tedds calculation version 2.2.22

Design summary
Overall design utilisation; 0.608
Overall design status; PASS

Dead results summary Unit Capacity Maximum Utilization Result

Bending stress lb/in2 1442 476 0.330 PASS
Shear stress lb/in2 233 18 0.078 PASS
Live results summary Unit Capacity Maximum Utilization Result
Bending stress lb/in2 2434 635 0.261 PASS
Shear stress lb/in2 311 18 0.058 PASS
Total long term deflection - C#3 results Unit Capacity Maximum Utilization Result
summary
Deflection in 0.8 0.486 0.608 PASS
Dead load deflection - C#3 results Unit Capacity Maximum Utilization Result
summary
Deflection in 0.533 0.215 0.403 PASS
 Project Job no.

Calcs for Start page no./Revision

DESIGN INN
19
Calcs by Calcs date Checked by Checked date Approved by Approved date

G 12/21/2025

Live load deflection - C#3 results Unit Capacity Maximum Utilization Result
summary
Deflection in 0.533 0.141 0.264 PASS

Dead
Member details
Service condition; Dry
Sawn lumber section details
Number of sections in member; N=1
Nominal breadth of sections; bnom = 2 in
Breadth of sections; b = 1.5 in
Nominal depth of sections; dnom = 6 in
Depth of sections; d = 5.5 in
Material; Douglas Fir-Larch, 2'' && wider, Select Structural grade

Span details
Unbraced length - Major axis; Lx = 16 ft
Effective bending length - Major axis; Le,x = 1.63  Lx + 3  b = 26.455 ft
Column buckling length - Major axis; Lb,x = Lx = 16 ft
Unbraced length - Minor axis; Ly = 16 ft
Effective bending length - Minor axis; Le,y = 1.63  Ly + 3  d = 27.455 ft
Column buckling length - Minor axis; Lb,y = Ly = 16 ft
Bearing length; Lb = 4 in
Analysis results
Design bending moment - Major axis; Mx = 300 lb_ft
Design shear force - Major axis; Vx = 100 lb
Adjustment factors - Table 4.3.1
Size factor for bending - Table 4A; CFb = 1.3
 Project Job no.

Calcs for Start page no./Revision

DESIGN INN
20
Calcs by Calcs date Checked by Checked date Approved by Approved date

G 12/21/2025

Depth-to-breadth ratio; dnom / bnom = 3.00

Slenderness ratio - eq.3.3-5; RB = (Le,y  d / b2) = 28.379
Reference bending design value; Fb = Fb  CFb  KFb  b   = 2526 lb/in2
Adjusted modulus of elasticity; Emin' = Emin  KFE  s = 1032240 lb/in2
Critical buckling design value - cl.[Link]; FbE = 1.2  Emin' / RB2 = 1538 lb/in2
Beam stability factor - eq.3.3-6
CL = [1 + (FbE / Fb)] / 1.9 - [([1 + (FbE / Fb)] / 1.9)2 - (FbE / Fb) / 0.95] = 0.571
Format conversion factor for bending - Table 2.3.5; KFb = 2.54
Format conversion factor for shear - Table 2.3.5; KFv = 2.88
Resistance factor for bending - Table 2.3.6; b = 0.85
Resistance factor for shear - Table 2.3.6; v = 0.75
Time effect factor - Table N.3;  = 0.6

Bending members - Flexure - cl.3.3

Design bending moment; Mx = 300 lb_ft
Design bending stress - Table 4.3.1; Fb,x' = Fb  CL  CFb  KFb  b   = 1442 lb/in2
Actual bending stress - eq.3.3-2; fb,x = Mx / Sx = 476 lb/in2
fb,x / Fb,x' = 0.330
PASS - Design bending stress exceeds actual bending stress
Bending members - Shear - cl.3.4
Design shear force; Vx = 100 lb
Design shear stress - Table 4.3.1; Fv,x' = Fv  KFv  v   = 233 lb/in2
Actual shear stress - eq.3.4-2; fv,x = 3  Vx / (2  b  d) = 18 lb/in2
fv,x / Fv,x' = 0.078
PASS - Design shear stress exceeds actual shear stress

Live
Member details
Service condition; Dry
Sawn lumber section details
Number of sections in member; N=1
Nominal breadth of sections; bnom = 2 in
Breadth of sections; b = 1.5 in
Nominal depth of sections; dnom = 6 in
Depth of sections; d = 5.5 in
Material; Douglas Fir-Larch, 2'' && wider, Select Structural grade
 Project Job no.

Calcs for Start page no./Revision

DESIGN INN
21
Calcs by Calcs date Checked by Checked date Approved by Approved date

G 12/21/2025

Span details
Unbraced length - Major axis; Lx = 16 ft
Effective bending length - Major axis; Le,x = Lx = 16 ft
Column buckling length - Major axis; Lb,x = Lx = 16 ft
Unbraced length - Minor axis; Ly = 16 ft
Effective bending length - Minor axis; Le,y = Ly = 16 ft
Column buckling length - Minor axis; Lb,y = Ly = 16 ft
Bearing length; Lb = 4 in
Analysis results
Design bending moment - Major axis; Mx = 400 lb_ft
Design shear force - Major axis; Vx = 100 lb
Adjustment factors - Table 4.3.1
Size factor for bending - Table 4A; CFb = 1.3
Repetitive member factor - Table 4.3.9; Cr = 1.15
Depth-to-breadth ratio; dnom / bnom = 3.00
Slenderness ratio - eq.3.3-5; RB = (Le,y  d / b2) = 21.664
Reference bending design value; Fb = Fb  CFb  Cr  KFb  b   = 3873 lb/in2
Adjusted modulus of elasticity; Emin' = Emin  KFE  s = 1032240 lb/in2
Critical buckling design value - cl.[Link]; FbE = 1.2  Emin' / RB2 = 2639 lb/in2
Beam stability factor - eq.3.3-6
CL = [1 + (FbE / Fb)] / 1.9 - [([1 + (FbE / Fb)] / 1.9)2 - (FbE / Fb) / 0.95] = 0.628
Format conversion factor for bending - Table 2.3.5; KFb = 2.54
Format conversion factor for shear - Table 2.3.5; KFv = 2.88
Resistance factor for bending - Table 2.3.6; b = 0.85
Resistance factor for shear - Table 2.3.6; v = 0.75
Time effect factor - Table N.3;  = 0.8
 Project Job no.

Calcs for Start page no./Revision

DESIGN INN
22
Calcs by Calcs date Checked by Checked date Approved by Approved date

G 12/21/2025

Bending members - Flexure - cl.3.3

Design bending moment; Mx = 400 lb_ft
Design bending stress - Table 4.3.1; Fb,x' = Fb  CL  CFb  Cr  KFb  b   = 2434 lb/in2
Actual bending stress - eq.3.3-2; fb,x = Mx / Sx = 635 lb/in2
fb,x / Fb,x' = 0.261
PASS - Design bending stress exceeds actual bending stress
Bending members - Shear - cl.3.4
Design shear force; Vx = 100 lb
Design shear stress - Table 4.3.1; Fv,x' = Fv  KFv  v   = 311 lb/in2
Actual shear stress - eq.3.4-2; fv,x = 3  Vx / (2  b  d) = 18 lb/in2
fv,x / Fv,x' = 0.058
PASS - Design shear stress exceeds actual shear stress

Total long term deflection - C#3

Member details
Service condition; Dry
Sawn lumber section details
Number of sections in member; N=1
Nominal breadth of sections; bnom = 2 in
Breadth of sections; b = 1.5 in
Nominal depth of sections; dnom = 6 in
Depth of sections; d = 5.5 in
Material; Douglas Fir-Larch, 2'' && wider, Select Structural grade

Span details
Span length; Ls = 16 ft
Analysis results
Deflection - Major axis; x = 0.356 in
 Project Job no.

Calcs for Start page no./Revision

DESIGN INN
23
Calcs by Calcs date Checked by Checked date Approved by Approved date

G 12/21/2025

Adjustment factors - Table 4.3.1

Repetitive member factor - Table 4.3.9; Cr = 1.15
Time dependent deformation factor - cl.3.5.2; Kcr = 1.5
Bending members - Deflection - cl.3.5
Instantaneous deflection; x = 0.356 in
Final deflection; x,Final = Kcr  0.734  x + 0.266  x = 0.486 in
Allowable deflection; x,Allowable = Ls / 240 = 0.8 in
x,Final / x,Allowable = 0.608
PASS - Allowable deflection exceeds final deflection

Dead load deflection - C#3

Member details
Service condition; Dry
Sawn lumber section details
Number of sections in member; N=1
Nominal breadth of sections; bnom = 2 in
Breadth of sections; b = 1.5 in
Nominal depth of sections; dnom = 6 in
Depth of sections; d = 5.5 in
Material; Douglas Fir-Larch, 2'' && wider, Select Structural grade

Span details
Span length; Ls = 16 ft
Analysis results
Deflection - Major axis; x = 0.215 in

Bending members - Deflection - cl.3.5

Instantaneous deflection; x = 0.215 in
 Project Job no.

Calcs for Start page no./Revision

DESIGN INN
24
Calcs by Calcs date Checked by Checked date Approved by Approved date

G 12/21/2025

Allowable deflection; x,Allowable = Ls / 360 = 0.533 in

x / x,Allowable = 0.403
PASS - Allowable deflection exceeds instantaneous deflection

Live load deflection - C#3

Member details
Service condition; Dry
Sawn lumber section details
Number of sections in member; N=1
Nominal breadth of sections; bnom = 2 in
Breadth of sections; b = 1.5 in
Nominal depth of sections; dnom = 6 in
Depth of sections; d = 5.5 in
Material; Douglas Fir-Larch, 2'' && wider, Select Structural grade

Span details
Span length; Ls = 16 ft
Analysis results
Deflection - Major axis; x = 0.141 in

Bending members - Deflection - cl.3.5

Instantaneous deflection; x = 0.141 in
Allowable deflection; x,Allowable = Ls / 360 = 0.533 in
x / x,Allowable = 0.264
PASS - Allowable deflection exceeds instantaneous deflection
 Project Job no.

Calcs for Start page no./Revision

DESIGN INN
25
Calcs by Calcs date Checked by Checked date Approved by Approved date

G 12/21/2025

4X6(2-2X6) SUPPORT
In accordance with the ANSI/AF&PA NDS 2018 using the LRFD method
Tedds calculation version 2.2.22

Design summary
Overall design utilisation; 0.02
Overall design status; PASS

Dead results summary Unit Capacity Maximum Utilization Result

Compressive stress lb/in2 991 16 0.016 PASS
Live results summary Unit Capacity Maximum Utilization Result
Compressive stress lb/in2 1031 21 0.020 PASS

Dead
Member details
Service condition; Dry
Sawn lumber section details
Number of sections in member; N=1
Nominal breadth of sections; bnom = 4 in
Breadth of sections; b = 3.5 in
Nominal depth of sections; dnom = 6 in
Depth of sections; d = 5.5 in
Material; Douglas Fir-Larch, 2'' && wider, Select Structural grade

Span details
Unbraced length - Major axis; Lx = 8 ft
Effective bending length - Major axis; Le,x = 1.63  Lx + 3  b = 13.915 ft
Column buckling length - Major axis; Lb,x = Lx = 8 ft
Unbraced length - Minor axis; Ly = 8 ft
Effective bending length - Minor axis; Le,y = 1.63  Ly + 3  d = 14.415 ft
Column buckling length - Minor axis; Lb,y = Ly = 8 ft
 Project Job no.

Calcs for Start page no./Revision

DESIGN INN
26
Calcs by Calcs date Checked by Checked date Approved by Approved date

G 12/21/2025

Analysis results
Design axial compression force; P = 300 lb
Adjustment factors - Table 4.3.1
Size factor for compression - Table 4A; CFc = 1.1
Reference compression design value; Fc = Fc  CFc  KFc  c   = 2424 lb/in2
Adjusted modulus of elasticity; Emin' = Emin  KFE  s = 1032240 lb/in2
Critical buckling design value; FcE = 0.822  Emin' / (Lb,y / b)2 = 1128 lb/in2
Column stability factor - eq.3.7-1
CP = (1 + (FcE / Fc)) / 1.6 - (((1 + (FcE / Fc)) / 1.6)2 - (FcE / Fc) / 0.8) = 0.409
Format conversion factor for comp. - Table 2.3.5; KFc = 2.4
[Link] for [Link] elasticity - Table 2.3.5; KFE = 1.76
Resistance factor for compression - Table 2.3.6; c = 0.9
Resistance factor for [Link] elasticity - Table 2.3.6; s = 0.85
Time effect factor - Table N.3;  = 0.6

Compression members - General - cl.3.6

Design axial compression force; P = 300 lb
Design compression parallel to grain - Table 4.3.1; Fc' = Fc  CFc  CP  KFc  c   = 991 lb/in2
Actual compression parallel to grain; fc = P / (b  d) = 16 lb/in2
fc / Fc' = 0.016
PASS - Design compression stress exceeds actual compression stress

Live
Member details
Service condition; Dry
Sawn lumber section details
Number of sections in member; N=1
Nominal breadth of sections; bnom = 4 in
Breadth of sections; b = 3.5 in
Nominal depth of sections; dnom = 6 in
Depth of sections; d = 5.5 in
Material; Douglas Fir-Larch, 2'' && wider, Select Structural grade
 Project Job no.

Calcs for Start page no./Revision

DESIGN INN
27
Calcs by Calcs date Checked by Checked date Approved by Approved date

G 12/21/2025

Span details
Unbraced length - Major axis; Lx = 8 ft
Effective bending length - Major axis; Le,x = Lx = 8 ft
Column buckling length - Major axis; Lb,x = Lx = 8 ft
Unbraced length - Minor axis; Ly = 8 ft
Effective bending length - Minor axis; Le,y = Ly = 8 ft
Column buckling length - Minor axis; Lb,y = Ly = 8 ft
Analysis results
Design axial compression force; P = 400 lb
Adjustment factors - Table 4.3.1
Size factor for compression - Table 4A; CFc = 1.1
Repetitive member factor - Table 4.3.9; Cr = 1.15
Reference compression design value; Fc = Fc  CFc  KFc  c   = 3231 lb/in2
Adjusted modulus of elasticity; Emin' = Emin  KFE  s = 1032240 lb/in2
Critical buckling design value; FcE = 0.822  Emin' / (Lb,y / b)2 = 1128 lb/in2
Column stability factor - eq.3.7-1
CP = (1 + (FcE / Fc)) / 1.6 - (((1 + (FcE / Fc)) / 1.6)2 - (FcE / Fc) / 0.8) = 0.319
Format conversion factor for comp. - Table 2.3.5; KFc = 2.4
[Link] for [Link] elasticity - Table 2.3.5; KFE = 1.76
Resistance factor for compression - Table 2.3.6; c = 0.9
Resistance factor for [Link] elasticity - Table 2.3.6; s = 0.85
Time effect factor - Table N.3;  = 0.8

Compression members - General - cl.3.6

Design axial compression force; P = 400 lb
Design compression parallel to grain - Table 4.3.1; Fc' = Fc  CFc  CP  KFc  c   = 1031 lb/in2
Actual compression parallel to grain; fc = P / (b  d) = 21 lb/in2
fc / Fc' = 0.020
PASS - Design compression stress exceeds actual compression stress
 Project Job no.

Calcs for Start page no./Revision

DESIGN INN
28
Calcs by Calcs date Checked by Checked date Approved by Approved date

G 12/21/2025