Concure S constructive solutions

Penetrating type and non film forming New concrete

concrete curing, sealing and dust proofing
Application to freshly placed concrete should not begin until
compound.
the surface is free from water, and should not commence at
Uses all if bleed water is apparent. Concure S should be applied as
soon as practically possible after removal of shuttering, and
Concure S seal the surface of fresh concrete and prevent rapid whilst the concrete surface is still damp. However, any traces
loss of [Link] a film of water retention enabling of laitance, grout runs or loose material should be removed.
curing of the concrete by reducing water loss from the concrete.
Application
Advantages
Concure S should be applied uniformly by brush, roller or
 Reduce surface shrinkage and cracking by eliminating spray, with no overlap of applications. Under standard site
moisture loss from exposed surfaces conditions, a single coat of Concure S applied at a uniform
 To help concrete hydrate more efficiently rate of 5.0 to 7.0 per liter. In case of sealing and dustproofing
application, 2 coats at the above range must be applied. The
 Easy to apply thus saves time and labour cost second coat should be applied at coverage of 10-15m2 per litre.
 Eliminates need for damp hessian, sand or polyethylene The applied film coating should not be trafficked until fully dry, and
Non film forming curing, sealing and dust proofing care should be taken to ensure that the film coating is not broken.
compound Spray equipment
Excellent moisture retention for freshly placed concrete, Power driven or knapsack spray equipment, which produces a
resulting in minimising shrinkage cracks fine spray, is recommended for use with Concure S.
Versatile - can be applied equally well to freshly placed Cleaning
or existing concrete
Spray equipment should be cleaned immediately after use by
Cost effective - can be over-coated with water based
flushing through with water. Any residual traces of resin which
and solvent based acrylic coatings, epoxy coatings,
are left in the nozzle may be cleaned with warm water.
polyurethane coatings.
Subsequent finishes
Description :
The chemical used in Concure S allows direct application of
Concure S is a liquid penetrating type curing compound based
many floor coverings and paint systems, as given typically
on high grade silicate compound. It is available in clear and
below:
with fugitive dye colour.
Water based emulsion paints containing PVA, PVC,
Standards compliance
acrylic co-polymers.
Concure S Complies to ASTM C 309 Type 1 and Type 1-D,
Bituminous emulsions and solutions
Class A.
Thin section polymer modifi ed cement systems
Properties
Epoxy resin coatings which do not rely on penetration for
Colour : Clear liquid
substrate bond
Specific gravity @ 25 deg C : 1.34 + 0.05
Polyurethane coating
Dry time (approximately) : Not > 4 hours
Water and solvent based acrylic coatings
Instructions for use

Preparation

Concure S should be gently stirred immediately prior to use

to ensure uniformity of the material as applied.

page 1 of 2
Concure S

Estimating Precautions
Coverage Health & Safety instructions

Coverage figures quoted for Concure S are indicative and based Fire
upon application to fresh or damp concrete at the appropriate
Concure S is non-flammable under normal condition.
time. Care should be taken to ensure that the concrete is indeed
ready to accept the curing material. Application rates outside Coverage
the range given below may be used if necessary, but it is
Approximately 6 m2/litre depending on surface conditions.
recommended to first contact your local fosroc office.
Packaging
Storage
Concure S is available in 200 litre, 235 litre and 20 litre.
When stored in warehouse conditions below 35°C, Concure S
has a minimum shelf life of 12 months.

Freezing and exposure to heat and/or direct sunlight should

be avoided.

Containers should be kept sealed and airtight to prevent any

reduction in shelf life.

Important note :
Fosroc products are guaranteed against defective materials and manufacture and are sold
subject to its standard terms and conditions of sale, copies of which may be obtained on
request. Whilst Fosroc endeavours to ensure that any advice, recommendation, specification
or information it may give is accurate and correct, it cannot, because it has, no direct or
continuous control over where or how its products are applied, accept any liability either
Fosroc Chemicals directly or indirectly arising from the use of its products whether or not in accordance with
any advice, specification, recommendation or information given by it.
(India) Pvt. Ltd.
Head Office telephone fax e-mail
Embassy Point, No. 150,
2nd Floor, Infantry Road, +91 80-42521900 +91 80-22281510 [Link]@[Link]
Bangalore 560 001,
Karnataka

Regional Offices

Chennai Mumbai Noida Kolkata

Hills Centre,Old No 5, MBC Park, 12th floor, Office No.12B, Unit No. 601, Highway Tower-II 304, Jodhpur Park
New No 9, 3rd Cross Street, ‘D’ Block, Near G Corp/Hyper City A-13/2, 6th Floor, Sector– 62 Kolkata 700 068
Jeth Nagar, Raja Annamalaipuram, Kasarwadawali, Ghodbunder Road, Gautam Buddha Nagar, Ph:+91 33-65343188
Chennai 600 028. Thane (West) 400 615 Noida 201 309, Uttar Pradesh Fax: 033-2499-0278
Ph: 9500064795 Ph: +91 22 6229 6800 Ph: +91 120 6121900
Fax: 0120-4270622

[Link]
page 2 of 2 INDIA/2024/0216/C