PAPER PRESENTATION
JAMMER
BY.
Mr. VINOD KUMAR
E.C.E(S4)
WORKING
It produces the frequency at which mobile frequency
It causes interference and cancel out
signals.
Hopping of frequency occurs to block frequency band.
Interrupt the communication between base station and
mobile.
Call and SMS is barred.
INTRODUCTION
SIGNAL BLOCKED
DESIGN AND IMPLIMENTATION
Power IF RF
Supply Section Section
5, 9,-9 V
POWER SUPPLY
The Jammer designed to take it’s power from the
regular 220V AC wall outlets.
The IF & RF sections of the jammer require +5, +9,
and -9 DC Voltages.
+ Regulator
+5V
+ Regulator
Transformer Rectifier Filter +9V
- Regulator
- 9V
FUNCTIONS OF IF SECTION
The function of the IF-section of the Mobile
jammer is to generate the tuning signal
required by the VCO in the RF-Section
The main parts of the IF-Section are:
– Triangular Wave Generator
– Noise Generator
– Signal Mixer and DC offset
IF SECTION
IF SECTION
TRIANGULAR WAVE GENERATOR
The circuit used to
generate
Triangular wave is the
555
Timer as astable
multivibrator.
The output frequency is
given
By following equation.
F=1.44/{(R1+R2)Cex}
NOISE GENERATOR
Noise will help in masking the jamming transmission,
making it look like random "noise" to an outside
observer.
The noise generator used is based on the avalanche
noise generated by a Zener breakdown phenomenon.
The noise generator circuit consists of:
– A standard 6.8 volt Zener diode with a small
– reverse current
– Transistor buffer
– National LM386 audio amplifier function as:
• Small signal amplifier
• Band pass filter
SIGNAL MIXER AND DC OFFSET CIRCUIT
The triangle wave and
noise signals are mixed
using Op-Amp configured
as summer.
A DC voltage is added to
the resulted signal to obtain
the required tuning voltage
using Diode-Clamper
circuit.
FUNCTIONS OF RF SECTION
The RF-section is responsible for generating and
transmitting the RF-Jamming signal. The main
parts are: VCO, Power Amplifier, and the
Antenna.
fortunately, all the parts used are internally
matched to 50ohm load, and hence transmission
lines used are microstrip lines designed to have
50ohm characteristic impedance
The components used are all surface mount
component
RF SECTION
RF SECT
VCO
The MAX2623 VCO from MAXIM IC was used to
generate the required signal
The output frequency range for the VCO is:
850 – 1000 MHz for a tune voltage from 0.4 – 2.6V.
The input tune frequency best suited the VCO was
120KHz to sweep the desired frequency range.
RF POWER AMPLIFIER
Two RF power amplifiers were used to achieve
the required output power (i.e. 34dBm).
The first stage power amplifier was the MAR-
4SM from Mini-Circuits it has a gain of 8dB for
frequency range from DC to 1000 MHz
so the output of this stage should be 5dBm
for the -3dBm output of the VCO
2 ND
STAGE AMPLIFIER
The second stage power amplifier is the Hitachi
PF08103b dual power amplifier with efficiency at
48%.
It can operate either on GSM-900 or DCS1800, so
external circuitry was designed to configure it to
operate in GSM mode
The output of the power amplifier is 35dBm
for 1dBm input
ANTENNA
1/4 wave monopole antenna, with center
frequency at 916Mhz and bandwidth of
150 MHz.
50 ohm impedance
VSWR < 1.7
Gain 2dBi
Connected to the RF-Section using RP-
SMA connector
ADVANTAGES AND APPLICATIONS
It blocks unwanted signals.
It is used to maintain peace & silence.
It is used to interrupt terrrorist
communication.
It is used in security purpose .
It is used in medical application.
DISADVANTAGE AND REMEDY
It can be used for blocking signal illegaly.
It can be used for tech-war.
It can be used for self benefit.
Question hour?
THANKING YOU….
