Electrical Stimulating Currents
Physiologic Response To
Electrical Current
Creating muscle contraction through
nerve or muscle stimulation
Stimulating sensory nerves to help in
treating pain
Creating an electrical field in biologic
tissues to stimulate or alter the healing
process
Physiologic Response To
Electrical Current
Creating an electrical field on the skin
surface to drive ions beneficial to the
healing process into or through the skin
Physiologic Response To
Electrical Current
As electricity moves through the body's
conductive medium, changes in the
physiologic functioning can occur at
various levels
Cellular
Tissue
Segmental
Systematic
Effects at Cellular Level
Excitation of nerve cells
Changes in cell membrane permeability
Protein synthesis
Stimulation of fibrobloast, osteoblast
Modification of microcirculation
Effects at Tissue Level
Skeletal muscle contraction
Smooth muscle contraction
Tissue regeneration
Effects at Segmental Level
Modification of joint mobility
Muscle pumping action to change
circulation and lymphatic activity
Alteration of the microvascular system
not associated with muscle pumping
Increased movement of charged
proteins into the lymphatic channels
Effects at Segmental Level
Transcutaneous electrical stimulation
cannot directly stimulate lymph smooth
muscle, or the autonomic nervous
system without also stimulating a motor
nerve
Systematic Effects
Analgesic effects as endongenous pain
suppressors are released and act at
different levels to control pain
Analgesic effects from the stimulation of
certain neurotransmitters to control
neural activity in the presence of pain
stimuli
Physiologic Response To
Electrical Current
Effects may be direct or indirect
Direct effects occur along lines of current
flow and under electrodes
Indirect effects occur remote to area of
current flow and are usually the result of
stimulating a natural physiologic event to
occur
Muscle and Nerve Responses
Excitability dependent on cell
membrane's voltage sensitive
permeability
Produces unequal distribution of charged
ions on each side of the membrane
creates a potential difference between the
charge of the interior of cell and exterior of cell
Potential difference is known as resting
potential because cell tries to maintain
electrochemical gradient as its normal
homeostatic environment
Muscle and Nerve Responses
Using active transport mechanism-cell
continually moves Na+ from inside cell to
outside and balances this positive charge
movement by moving K+ to the inside
Produces an electrical gradient with + charges
outside and - charges inside
Nerve Depolarization
To create transmission of an impulse in
nerve, resting membrane potential must
be reduced below threshold level
Changes in membrane's permeability
may then occur creating an action
potential that propagates impulse along
nerve in both directions causing
depolarization of membrane
Nerve Depolarization
Stimulus must have adequate intensity
and last long enough to equal or exceed
membrane's basic threshold for excitation
Stimulus must alter membrane so that a
number of ions are pushed across
membrane exceeding ability of the active
transport pumps to maintain the resting
potentials thus forcing membrane to
depolarize resulting in an action potential
Depolarization Propagation
Difference in electrical potential between
depolarized region and neighboring inactive
regions causes the current to flow from
depolarized region intercellular material to the
inactive membrane
Depolarization Propagation
Current also flows through extracellular
materials, back to the depolarized area, and
finally into cell again
Makes depolarization self propagating as
process is repeated all along fiber in each
direction from depolarization site.
Depolarization Effects
As nerve impulse
reaches effector
organ or another
nerve cell, impulse
is transferred
between the two at
a motor end plate or
a synapse
Depolarization Effects
At this junction, a
transmitter
substance is
released from nerve
Transmitter
substance causes
the other excitable
tissue to discharge
causing a twitch
muscle contraction
Strength - Duration Curves
Represents The
Threshold for
Depolarization of a
Nerve Fiber
Muscle and nerve
respond in an
all-or-none fashion
and there is no
gradation of response
Strength - Duration Curves
Shape of the
curve relates
intensity of
electrical stimulus
(strength) and
length of time
(duration)
necessary to
cause the tissue to
depolarize
Strength - Duration Curves
Rheobase describes
minimum intensity of
current necessary to
cause tissue excitation
when applied for a
maximum duration
Strength - Duration Curves
Chronaxie describes
length of time
(duration) required for
a current of twice the
intensity of the
rheobase current to
produce tissue
excitation
Strength - Duration Curves
A sensory, motor, A
sensory, and C pain nerve
fibers
Durations of several
electrical stimulators are
indicated along the lower
axis
Corresponding intensities
would be necessary to
create a depolarizing
stimulus for any of the
nerve fibers
Effects of Changing Current
Parameters
Alternating versus direct current
Tissue impedance
Current density
Frequency of wave or pulse
Intensity of wave or pulse
Duration of wave or pulse
Polarity of electrodes
Electrode placement
Alternating vs. Direct Current
Nerve doesnt know
the difference
between AC and DC
With continuous
direct current a
muscle contraction
would occur only
when the current
intensity rose to a
stimulus threshold
Alternating vs. Direct Current
Once the membrane
repolarized, another
change in the
current intensity
would be needed to
force another
depolarization and
contraction
Alternating vs. Direct Current
Biggest difference in effects of
alternating and direct currents is ability
of direct current to cause chemical
changes
Chemical effects from using direct
current usually occur only when
stimulus is continuous and is applied
over a period of time
Tissue Impedance
Impedance -resistance of the tissue to
the passage of electrical current.
Bone and fat are high-impedance
tissues; nerve and muscle are low-
impedance
If a low-impedance tissue is located
under a large amount of high-
impedance tissue current will never
become high enough to cause a
depolarization
Current Density
Current Density- - Refers To The Volume Of
Current In The Tissues
Highest At Surface And Diminishes In Deeper
Tissue
Altering Current Density
Change The Spacing Of Electrodes
Moving Further Apart Increases Current Density In
Deeper Tissues
Active vs. Dispersive Electrodes
Changing The Size Of The Electrode
Active Electrode Is The Smaller of The Two
Current Density Is Greater
Dispersive Electrode Is The Larger
Current Density Is Less
Frequency (CPS, PPS, Hz)
Effects the type of muscle contraction
Effects the mechanism of pain modulation
Intensity
Increasing the
intensity of the
electrical stimulus
causes the current to
reach deeper into the
tissue
Recruitment of Nerve Fibers
A stimulus pulse at a
duration-intensity just
above threshold will
excite the closest and
largest fibers
Recruitment of Nerve Fibers
Increasing the
intensity will excite
smaller fibers and
fibers farther away. C,
Increasing the
duration will also
excite smaller fibers
and fibers farther
away.
Duration
We also can stimulate
more nerve fibers with
the same intensity
current by increasing
the length of time
(duration) that an
adequate stimulus is
available to depolarize
the membranes
Polarity
Anode
Positive Electrode With Lowest Concentration
of Electrons
Cathode
Negative Electrode With Greatest
Concentration of Electrons
Polarity Switch Designates One Electrode
As Positive and One As Negative
Polarity
With AC Current and Interrupted DC
Current Polarity Is Not Critical
Select Negative Polarity For Muscle
Contraction
Facilitates Membrane Depolarization
Usually Considered More Comfortable
Negative Electrode Is Usually Positioned
Distally
Polarity With Continuous DC
Current
Important Consideration When Using Iontophoresis
Positive Pole
Attracts - Ions
Acidic Reaction
Hardening of Tissues
Decreased Nerve
Irritability
Negative Pole
Attracts + Ions
Alkaline Reaction
Softening of Tissues
Increased Nerve
Irritability
Electrode Placement
Electrodes may be placed:
On or around the painful area
Over specific dermatomes, myotomes, or
sclerotomes that correspond to the painful
area
Close to spinal cord segment that innervates
an area that is painful
Over sites where peripheral nerves that
innervate the painful area becomes
superficial and can be easily stimulated
Electrode Placement
Electrodes may be placed:
Over superficial vascular structures
Over trigger point locations
Over acupuncture points
In a criss-cross pattern around the point to be
stimulated so the area to be treated is central
to the location of the electrodes
If treatment is not working- change placement
Therapeutic Uses of Electrically
Induced Muscle Contraction
Muscle reeducation
Muscle pump contractions
Retardation of atrophy
Muscle strengthening
Increasing range of motion
Reducing Edema
Muscle Re-Education
Muscular inhibition after surgery or
injury is primary indication
A muscle contraction usually can be
forced by electrically stimulating the
muscle
Patient feels the muscle contract, sees
the muscle contract, and can attempt to
duplicate this muscular response
Muscle Re-Education Protocol
Current intensity must be adequate for
muscle contraction but comfortable
Pulse duration must be set as close as
possible to the duration needed for
chronaxie of the tissue to be stimulated
Pulses per second should be high
enough to give a tetanic contraction (20
to 40 pps)
Muscle Re-Education Protocol
Interrupted or surged current must be
used
High-voltage pulsed or medium-frequency
alternating current may be most effective
On time should be 1 to 2 seconds
Off time should be 4 to 10 seconds
Total treatment time should be about 15
minutes, repeated several times daily
Muscle Re-Education Protocol
Patient should be instructed to allow just
the electricity to make the muscle
contract, feeling and seeing the response
desired
Next, patient should alternate voluntary
muscle contractions with current-induced
contractions
Muscle Pump Contractions
Used to duplicate the regular muscle
contractions that help stimulate
circulation by pumping fluid and blood
through venous and lymphatic channels
back to the heart
Can help in reestablishing proper
circulatory pattern while keeping injured
part protected
Muscle Pump Contractions
Current intensity must be high enough
to provide a strong, comfortable muscle
contraction
Pulse duration should be set as close
as possible to the duration needed for
chronaxie of the motor nerve to be
stimulated if not preset
Muscle Pump Contractions
Pulses per second should be at
beginning of tetany range (20 pps).
Interrupted or surged current must be
used
On time should be 5 to 10 seconds.
Off time should be 5 to 10 seconds.
The part to be treated should be elevated
Total treatment time should be 20 to 30
minutesrepeated two to five times daily
8. The athlete should be instructed to
allow the electricity to make the muscles
contract. Active range of motion may be
encouraged at the same time if it is not
contraindicated.
9. 10. High-voltage pulsed or medium-
frequency alternating current may be
most effective.32,39,94,97,111 (See Fig.
5-20).
11. Use this protocol in addition to the
normal I.C.E. for best effect.41,88
Muscle Pump Contractions
High-voltage pulsed or medium-
frequency alternating current may be
most effective
Athlete should be instructed to allow the
electricity to make the muscles contract.
Active range of motion may be
encouraged at the same time if it is not
contraindicated
Retardation of Atrophy
Electrical stimulation reproduces
physical and chemical events
associated with normal voluntary
muscle contraction and helps to
maintain normal muscle function
Retardation of Atrophy
Current intensity should be as high as
can be tolerated
Contraction should be capable of
moving the limb through the antigravity
range or of achieving 25% or more of
the normal maximum voluntary
isometric contraction (MVIC) torque for
the muscle
Retardation of Atrophy
Pulse duration should be set as close as
possible to the duration needed for
chronaxie of the motor nerve to be
stimulated
Pulses per second should be in the tetany
range (20 to 85 pps)
Interrupted or surge type current should be
used
Medium-frequency alternating current
stimulator is the machine of choice
Retardation of Atrophy
On time should be between 6 and 15
seconds
Off time should be at least one minute
preferably two minutes.
Muscle should be given some resistance,
either gravity or external resistance
provided by the addition of weights or by
fixing the joint so that the contraction
becomes isometric
Retardation of Atrophy
Patient can be instructed to work with
electrically induced contraction, but
voluntary effort is not necessary
Total treatment time should be 15 to 20
minutes, or enough time to allow a
minimum of 10 contractions
Treatment can be repeated two times
daily
Muscle Strengthening
Current intensity should make muscle
develop 60% of torque developed in a
maximum voluntary isometric
contraction (MVIC)
Pulse duration should be set as close
as possible to the duration needed for
chronaxie of the motor nerve to be
stimulated
Muscle Strengthening
Pulses per second should be in the tetany
range (20 85 pps)
Surged or interrupted current with a
gradual ramp to peak intensity most
effective
On time should be 10-15 seconds
Off time should be 50 seconds to 2
minutes
Medium-frequency alternating current
stimulator is machine of choice
Muscle Strengthening
Muscle is given an isometric contraction
torque equal to or greater than 25% of the
MVIC torque
Patient instructed to work with the
electrically induced contraction, but
voluntary effort is not necessary
Total treatment should mimick normal
active resistive training protocols of 3 sets
of 10 contractions
Increasing Range of Motion
Electrically stimulating a muscle
contraction pulls joint through limited
range
Continued contraction of muscle group
over extended time appears to make
contracted joint and muscle tissue
modify and lengthen
Increasing Range of Motion
Current intensity must be of sufficient
intensity and duration to make muscle
contract strongly enough to move the body
part through antigravity range
Pulse duration should be set as close as
possible to the duration needed for
chronaxie of the motor nerve to be
stimulated
Increasing Range of Motion
Pulses per second should be at the
beginning of the tetany range (20 to 30
pps)
Interrupted or surged current should be
used
On time should be between 15 and 20
secs
Off time should be equal to or greater
than on time, fatigue is a big consideration
High-voltage pulsed or medium-frequency
alternating current stimulators are
suggested
The stimulated muscle group should be
antagonistic to the joint contracture and
the athlete should be positioned so the
joint will be moved to the limits of the
available range.
8. The athlete is passive in this treatment
and does not work with the electrical
contraction.
9. Total treatment time should be 90
minutes daily. This can be broken into
three 30-minute treatments.
10..
Increasing Range of Motion
Stimulated muscle group should be
antagonistic to joint contracture and
patient should be positioned so joint will
be moved to the limits of available range
Patient is passive in treatment and does
not work with electrical contraction
Total treatment time should be 90 minutes
daily broken into 3 x 30-minute treatments
Reducing Edema
Sensory level direct current used as a
driving force to make charged plasma
protein ions in interstitial spaces move
in the direction of oppositely charged
electrode
Reducing Edema
Current intensity should be (30V-50V)
or 10% less than needed to produce a
visible muscle contraction
Preset short duration interrupted DC
currents with high pulse frequencies
(120 pps) on high voltage equipment
are effective
Reducing Edema
Distal electrode should be negative
Treatment should begin immediately
after injury
Thirty minute treatment showed good
control of volume for 4 to 5 hours
High voltage pulsed generators are
effective, low voltage generators are not
effective
Stimulating Denervated Muscle
Electrical currents may be used to
produce a muscle contraction in
denervated muscle
Denervated muscle has lost its peripheral
nerve supply
Purpose for electrically stimulating
denervated muscle is to help minimize
the extent of atrophy while the nerve is
regenerating
Stimulating Denervated Muscle
Muscle fibers experience a decrease in
size, diameter and weight of the
individual muscle fibers
There is a decrease in amount of tension
which can be generated and an increase
in the time required for contraction
Stimulating Denervated Muscle
Degenerative changes progress until
muscle is reinnervated by axons
regenerating across site of lesion
If reinnervation does not occur within 2
years fibrous connective tissue replaces
contractile elements and recovery of
muscle function is not possible
Stimulating Denervated Muscle
A current with an asymmetric, biphasic
(faradic)waveform pulse duration < 1 ms
may be used during the first 2 weeks
After 2 weeks, either an interrupted DC
square wave or a progressive DC
exponential wave with long pulse duration
> 10 ms, or a AC sine wave with
frequency < 10 Hz will produce a twitch
contraction
Stimulating Denervated Muscle
Length of pulse should be as short as possible
but long enough to elicit a contraction
Current waveform should have pulse duration
= or > than chronaxie of denervated muscle
Amplitude of current along with pulse duration
must be sufficient to stimulate a denervated
muscle with a prolonged chronaxie while
producing a moderately strong contraction of
muscle fibers
Stimulating Denervated Muscle
Pause between stimuli should be 4 to 5 times
longer (about 3-6 seconds) than stimulus
duration to minimize fatigue
Either a monopolar or bipolar electrode setup
can be used with small diameter active
electrode placed over most electrically active
point
Stimulation should begin immediately using 3
sets of 5 -20 repetitions 3 x per day
Therapeutic Uses of Electrical
Stimulation of Sensory Nerves
Gate Control Theory
Descending Pain Control
Opiate Pain Control
Gate Control Theory
Current intensity adjusted to tolerance
but should not cause muscular
contraction
Pulse duration should be 75 -150 sec
or maximum possible
Pulses per second should be 80-125 or
as high as possible
A transcutaneous electrical stimulator
waveform should be used
Gate Control Theory
Continuous on time should be used
Total treatment time should correspond
to fluctuations in pain;
Unit should be left on until pain is no longer
perceived, turned off, then restarted when
pain begins again
Should have positive result in 30 min. if
not reposition electrodes
Descending Pain Control
(Central Biasing)
Current intensity should be very high,
approaching noxious level
Pulse duration should be 10 msec.
Pulses per second should be 80.
On time should be 30 seconds to 1
minute
Stimulation should be applied over
trigger or acupuncture points
Descending Pain Control
(Central Biasing)
Selection and number of points used
varies according to the part treated.
Low-frequency,high-intensity generator
is stimulator of choice for central biasing
Should have positive result shortly after
treatment begins-if not reposition
electrodes
Opiate Pain Control Theory
Current intensity should be high, at a
noxious level- muscular contraction is
acceptable
Pulse duration should be 200 sec to 10
msec
Pulses per second should be 1-5.
High-voltage pulsed current should be used.
On time should be 30 to 45 seconds.
Stimulation should be applied over trigger or
acupuncture points
Opiate Pain Control Theory
Selection and number of points used varies
according to part and condition being
treated
High-voltage pulsed current or a low-
frequency, high-intensity machine is best
Analgesic effect should last for several (6-7)
hours
If not successful, try expanding the number of
stimulation sites
Clinical Uses of Low-Volt
Continuous Direct Current
Medical Galvinism
Ionotphoresis
Medical Galvanism
Continuous low-volt direct current causes:
Polar effects
Acid reaction around the positive pole and the alkaline
reaction at the negative pole
Acidic or alkaline changes can cause severe skin
reactions
Occur only with low-voltage continuous direct current
and are not likely with the high-voltage generators since
current duration is too short to cause chemical changes
Vasomotor Changes
Blood flow increases between the electrodes.
Medical Galvanism
Current intensity should be to tolerance
Intensity in the milliamp range.
Continuous direct current should be
used
Pulses per second should be 0.
Low-voltage direct current stimulator is
the machine of choice.
Treatment time should be between 15-
50 min
Medical Galvanism
Equal-sized electrodes are used over
gauze that has been soaked in saline
solution and lightly squeezed
Skin should be unbroken
Skin burns are the greatest hazard of
any continuous direct current technique
Functional Electrical Stimulation
FES utilizes multiple channel electrical
stimulators controlled by a
microprocessor to recruit muscles in a
programmed synergystic sequence that
will allow patient to accomplish a
specific functional movement pattern
Multichannel microprocessors may be
pre-programmed to execute a variety of
specific movement patterns
Low Intensity Stimulators
Originally called microcurrent electrical
neuromuscular stimulators (MENS)
LIS currents are not substantially
different from the currents discussed
previously
LIS generators produce current where
intensity is limited to <1000 microamps
(1 milliamp) while intensity of standard
low-voltage equipment can be
increased into milliamp range
Low Intensity Stimulators
Low intensity stimulation has been used
for two major effects:
Analgesia of the painful area
Biostimulation of the healing process either
for enhancing the process or for
acceleration of its stages
Used to promote wound healing (skin ulcers)
and fracture healing (nonunion
Analgesic Effects of LIS
LIS is a subsensory current
As such it does not fit existing models of
pain modulation
Exact mechanism of action has not yet
been established
LIS can create or change constant direct
current flow of the neural tissues which may
have some way of biasing transmission of
painful stimulus
May also make nerve cell membrane more
receptive to neurotransmitters which will block
transmission
Promotion of Wound Healing
Low intensity stimulators can be used
but other generators with intensities
adjusted to sub-sensory levels can also
be effective
Current intensity is 200-400 amp for
normal skin and 400-800 amp for
denervated skin
Long pulse durations or continuous
uninterrupted currents can be used
Promotion of Wound Healing
Maximum pulse frequency
Monophasic direct current is best but
biphasic direct current is acceptable. A
battery powered portable unit is most
convenient.
Treatment time 2 hours followed by a 4
hour rest time
2-3 treatment bouts per day
Promotion of Wound Healing
Negative electrode positioned in the
wound area for the first 3 days
Positive electrode positioned 25 cm
proximal to the wound
After 3 days polarity reversed and
positive electrode is positioned in the
wound area
Promotion of Wound Healing
With infection negative electrode should
be left in wound area until the signs of
infection are not evident and for 3 more
days after infection clears
If wound size decrease plateaus return
the negative electrode to the wound
area for 3 days
Promotion of Fracture Healing
Current intensity is just perceptible to
patient
Pulse duration is longest duration allowed
on unit (100 to 200 msec)
Pulses per second set at lowest frequency
allowed on unit (5 to 10 pps)
Standard monophasic or biphasic current in
TENS units used
Promotion of Fracture Healing
Treatment time 30 minutes-1 hour 3-4 x
daily
Negative electrode placed close to but
distal to fracture site
Positive electrode placed proximal to
immobilizing device
Results reassessed at monthly intervals
Russian Currents
Deliver medium (2000 -10,000 Hz)
frequency polyphasic AC wave form
Pulse varies from 50-250 sec; the
phase duration is half of the pulse
duration or 25-125 sec
Two basic waveforms: sine wave or
square wave cycles with a fixed
intrapulse interval
Russian Currents
Sine wave produced in burst mode with 50%
duty cycle
To make intensity of current tolerable it is
generated in 50-burst-per-second envelopes
with an interburst interval of 10 msec
Russian Currents
Dark shaded area represents total current,
and light shading indicates total current
without the interburst interval
When generated with burst effect total current
is decreased allowing for tolerance of greater
current intensity
Russian Currents
Higher frequency currents reduce
resistance to current flow making wave
form comfortable enough to tolerate
higher intensities
As intensity increases more motor nerves
are stimulated increasing magnitude of
the contraction
Russian Currents
Because it is a fast oscillating AC current,
as soon as nerve repolarizes it is
stimulated again, producing a current that
will maximally summate muscle
contraction
Interferential Currents
Make use of 2 separate generators
Produce sine waves at different frequencies
Interferential Currents
When displayed on an oscilloscope with only one
generator the current behaves as previously
described
Interferential Currents
If a second generator is added the currents
may interfere with each other
If produced in phase if or they originate at
same time interference can be summative-
amplitudes of the electric wave are combined
and increase
Referred to as constructive interference
Interferential Currents
If waves are
generated out of sync,
Generator 1 starts in a
positive direction at
the same time that
Generator 2 starts in a
negative direction-
waves cancel each
other out
Referred to as
destructive
interference
Interferential Currents
If two generators have
slightly different
frequencies they are out
of phase an thus create a
beat pattern
Blending of waves
caused by
constructive and
destructive
interference patterns
called heterodyne
effect
Interferential Currents
When using an interference current
Set intensity according to peak
Select the frequencies to create a beat
frequency corresponding to choices of
frequency when using other stimulators
20 to 50 pps for muscle contraction
50 to 120 pps for pain management
1 pps for acustim pain relief
Interferential Currents
When electrodes are arranged in a square
and interferential currents are passed through
a homogeneous medium a predictable
pattern of interference will occur
Interferential Currents
An electric field is created where two currents
cross between lines of electric current flow
Maximum interference effect takes place near
center, with field gradually decreasing in
strength as it moves away from center
Interferential Currents
Scanning interferential current moves force
around while the treatment is taking place
enlarging effective treatment area
Another set of electrodes create a three-
dimensional flower effect called a
stereodynamic effect
