Lesson 2: Configure
Computer System and
Network
COMPUTER HARDWARE SERVICING GRADE 10
What to Know?
LESSON 2.1
SAFETY PRECAUTIONS
RELATED TO NETWORK
SAFETY PRECAUTIONS
RELATEDTO NETWORK
Safety precautions when using a ladder:
Read the labels on the ladder, and follow any
safety instructions written on it.
Never stand on the top rung of the ladder. You
could easily lose your balance and fall.
Make sure that people in the area know you will
be working there.
Cordon off the area with caution tape or safety
cones.
When you are using a ladder that leans up
against a wall, follow the instructions written on the
ladder, and have someone hold the ladder to help
keep it steady.
Safety rules when working
with cables:
The tools required to install copper and fiber-optic
cable may cause danger through improper use. When
working with cables, strictly follow these safety rules:
Make sure that the tools you are using are in good
working condition.
Watch what you are doing, and take your time.
Make sure that you do not cut yourself or place
anyone in danger.
Safety rules when working
with cables:
Always wear safety glasses when cutting, stripping, or
splicing cables of any kind. Tiny fragments can injure
your eyes.
Wear gloves whenever possible, and dispose any waste
properly.
Note:
Use common sense when installing cables and fixing
network problems. Call for assistance for tasks that you
cannot do on your own.
FIBER OPTICS SAFETY
Fiber-Optic Safety
Fiber-optic cables are useful for
communications, but they have certain
hazards:
Dangerous chemicals
Fiber-Optic Safety
Fiber-optic cables are useful for
communications, but they have certain
hazards:
Tools with sharp edges
Fiber-Optic Safety
Fiber-optic cables are useful for
communications, but they have certain
hazards:
Light which you cannot see that can burn
your eyes
Fiber-Optic Safety
Fiber-optic cables are useful for
communications, but they have certain
hazards:
Glass shards produced by cutting fiberoptic cable that can cause bodily harm
What to Know?
LESSON 2.2
Networking Devices,
Media and Connector
Common Network Cables
[Link] pair is a type of copper cabling
that is used for telephone communications
and most Ethernet networks.
A pair of wires forms a circuit that transmits
data.
The pair is twisted to provide protection against
crosstalk, the noise generated by adjacent pairs
of wires in the cable.
Pairs of copper wires are encased in color-coded
plastic insulation and are twisted together.
An outer jacket protects the bundles of twisted
pairs.
The two basic types of twisted-pair
cables are as follows:
1. Unshielded twisted pair (UTP) is the cable that has
two or four pairs of wires. This type of cable relies solely
on the cancellation effect produced by the twisted-wire
pairs that limits signal degradation caused by
electromagnetic interface (EMI) and radio frequency
interference (RFI). UTP is the most commonly used
cabling in networks. UTP cables have a range of 328 feet
(100 m).
The two basic types of twisted-pair
cables are as follows:
With shielded twisted pair (STP), each pair of wire is
wrapped in metallic foil to better shield the wires from
noise. Four pairs of wires are then wrapped in an overall
metallic braid or foil. STP reduces electrical noise from
within the cable.
Category Rating
UTP comes in several categories that are
based on two factors:
The number of wires in the cable
The number of twists in those wires
Category Rating
Category 3 is the
wiring used for
telephone systems
and Ethernet LAN
at 10 Mega byte
per second
(Mbps).
Category Rating
Category 3 has
four pairs of wires
Category Rating
Category 5 and Category
5e have four pairs of
wires with a
transmission rate of 100
Mbps
Category 5 and Category
5e is the most common
network cables used.
5. Category 5e has more
twists per foot than
Category 5 wiring.
Coaxial Cable
Coaxial cable is a
copper-cored cable
surrounded by a heavy
shielding. Coaxial cable
is used to connect the
computers to the rest
of the network.
Coaxial Cable
Coaxial cable uses British Naval
Connectors (BNC) or Bayonet
Neill-Concelman connectors, at
the ends of the cables to make the
connection.
Coaxial Cable
Several types of coaxial cable exist:
Thicknet (10BASE5) is a coaxial cable
used in networks operating at 10 Mbps,
with a maximum length of 500 meters.
Thinnet (10BASE2) is a coaxial cable
used in networks operating at 10 Mbps,
with a maximum length of 185 meters.
RG-59 is most commonly used for
cable television in the U.S.
RG-6 is higher-quality cable than RG59, with more bandwidth and less
susceptibility to interference.
Fiber-Optic Cable
Fiber-Optic Cable
An optical fiber is a glass or plastic conductor
that transmits information using light.
has one or more optical fibers enclosed in a
sheath or jacket.
Fiber-Optic Cable
Common connectors for fiber-optic
networks
SC
ST
LC
These three types of fiber-optic connectors
are half-duplex, which allows data to flow
in only one direction. Therefore, two
cables are needed.
These are the two types of
glass fiber-optic cable:
Multimode is the cable that has a thicker
core than single-mode cable. It is easier to
make, can use simpler light sources such
as Light Emitting Diodes (LEDs), and
works well over distances of a few
kilometers or less.
Single-mode is the cable that has a very
thin core. It is harder to make, uses lasers
as a light source, and can transmit signals
dozens of kilometers with ease.
Creating Ethernet Cable
Fabricating an Ethernet
Cross-over and
Straight-through Cable
straight-through
Ethernet cable is
used in local area
network to connect a
PC to a network hub
and router.
This is the standard
cable used for almost
all purposes.
Fabricating an Ethernet
Cross-over and
Straight-through Cable
cross-over cable
can be used to connect
two network devices
directly, without the
need for a router in the
middle.
It simply reverses some
of the pins so that the
output on one computer
is being sent to the
input of another.
MATERIALS and TOOLS used
in ETHERNET CABLE
Ethernet Cable Category 5e or
Cat5e- standard wire for cabling;
RJ45 crimpable connectors for
Cat5e;
RJ45 Crimping tool;
Wire cutter, stripper or pliers; and
Ethernet cable tester.
Cat5e cable
1000Mbps data capacity
For runs of up to 90 meters
Solid core cable ideal for structural installations (PVC or
Plenum)
Stranded cable ideal for patch cables
Terminated with RJ-45 connectors
RJ45 connector
Making connections - Tools
Cat5e cable
RJ45 connectors
Cable stripper
Scissors
Crimping tool
Making connections - Steps
1.
2.
3.
4.
5.
6.
7.
8.
Strip cable end
Untwist wire ends
Arrange wires
Trim wires to size
Attach connector
Check
Crimp
Test
Step 1 Strip cable end
Strip 1 1 of insulating sheath
Avoid cutting into conductor insulation
Step 2 Untwist wire ends
Sort wires by insulation colors
Step 3 Arrange wires
TIA/EIA 568A: GW-G OW-Bl BlW-O BrW-Br
TIA/EIA 568B: OW-O GW-Bl BlW-G BrW-Br
Step 4 Trim wires to size
Trim all wires evenly
Leave about of wires
exposed
Step 5 Attach connector
Maintain wire order,
left-to-right, with
RJ45 tab facing
downward
Step 6 - Check
Do all wires extend to end?
Is sheath well inside connector?
Step 7 - Crimp
Squeeze firmly to crimp connecter
onto cable end (8P)
Step 8 Test
Does the cable work?
What to Know?
LESSON 2.3
SAFETY PRECAUTIONS
RELATED TO NETWORK
