Chapter 1

Lecture slides by
[Link] Yousufuddin
The jet engines on
modern
commercial
airplanes are
highly complex
turbomachines that
include both pump
(compressor) and
turbine sections.

2
INTRODUCTION

• The pump is mechanical device which conveys liquid from one place to
another place. It can be defined as a hydraulic machines which converts
the mechanical energy into hydraulic energy(pressure energy of liquid)
• The pump is power absorbing machines.
• The power can be supplied to the pump by a prime motor like an electric
motor, an internal combustion engine or turbine.
• Pumping means addition of energy to a liquid to move it from one place to
the another, and this done by means of piston, plunger, impeller, propeller,
gears or screw depending upon types of pumps
• The purpose of pumps may be increasing the pressure energy, imparting
kinetic energy, lifting and circulating or extracting liquids etc.
• The pump are used for various applications in various fields as follows:
1. Thermal engineering:
2. To feed water in to the boiler
3. To circulate the water in condenser
4. To circulate lubricating oil in the proper place in various machines

5. Agriculture and irrigation:

6. To lift water from deep well
7. To convey water from one place to another

8. Chemical industries:
9. Municipal water works and drainage system
10. Hydraulic control systems
CLASSIFICATION OF
PUMPS
• The pump can be classified according to principle by which the energy added to the fluid and
their design features as follows:
1. Positive displacement pump: These pumps operate on the principle of a definite quantity of liquid is
discharged or displaced due to the positive or real displacement of working element like piston,
plunger, gears, etc..

2. Reciprocating pump:
1. Piston pumps:
1. Single cylinder single acting or double acting.
2. Double cylinder single acting or double acting.
2. Plunger pumps
3. Bucket pump-Hand pumps
3. Rotory pumps:
1. Gear pumps
2. Vane/lobe pumps
3. Screw pumps
2. Roto-dynamic pump: These pumps operate on the principle of the rise in pressure energy of
liquid by dynamic action of liquid. The dynamic action of liquid is carried by revolving wheel
which ha curved vanes on it. This wheel is known as impeller.

Radial flow pump: In this pump, addition of energy to the liquid occurs when the flow of liquid in radial path.
[Link] pumps:
1. Single stage
2. Multi stage
Axial flow pump: In this pump, addition of energy to the liquid occurs when the flow of liquid in axial direction.
Mixed flow pump: In this pump, addition of energy to the liquid occurs when the flow of liquid in axial as well as
radial directions.

3. Other type of pumps: This types of pumps does not belongs to the category of
positive displacement or roto-dynamic type pumps as follows:

4. Jet pump
5. Air lift pump
7
 CLASSIFICATIONS AND TERMINOLOGY
Pumps: Energy absorbing devices
since energy is supplied to them,
and they transfer most of that
energy to the fluid, usually via a
rotating shaft. The increase in fluid
energy is usually felt as an
increase in the pressure of the
fluid.
Turbines: Energy producing devices
they extract energy from the fluid
and transfer most of that energy to
some form of mechanical energy
output, typically in the form of a
rotating shaft. The fluid at the outlet
of a turbine suffers an energy loss,
typically in the form of a loss of
pressure. (a) A pump supplies energy to a fluid,
while (b) a turbine extracts energy
from a fluid.
8
The purpose of a pump is to add
energy to a fluid, resulting in an
increase in fluid pressure, not
necessarily an increase of fluid
speed across the pump.
The purpose of a turbine is to
extract energy from a fluid,
resulting in a decrease of fluid
pressure, not necessarily a
For the case of steady flow,
decrease of fluid speed across
conservation of mass requires that the
the turbine. mass flow rate out of a pump must
equal the mass flow rate into the pump;
for incompressible flow with equal inlet
and outlet cross-sectional areas (Dout =
Din), we conclude that Vout = Vin, but Pout
> Pin.

9
Pump: Fluid machines that move liquids.
Fan: A gas pump with relatively low
pressure rise and high flow rate.
Examples include ceiling fans, house
fans, and propellers. When used with gases, pumps are
Blower: A gas pump with relatively called fans, blowers, or compressors,
moderate to high pressure rise and depending on the relative values of
moderate to high flow rate. Examples pressure rise and volume flow rate.
include centrifugal blowers and squirrel
cage blowers in automobile ventilation
systems, furnaces, and leaf blowers.
Compressor: A gas pump designed to
deliver a very high pressure rise,
typically at low to moderate flow rates.
Examples include air compressors that
run pneumatic tools and inflate tires at
automobile service stations, and
refrigerant compressors used in heat
pumps, refrigerators, and air
conditioners.
10
11
Turbomachines: Pumps and
turbines in which energy is supplied
or extracted by a rotating shaft.
The words turbomachine and
turbomachinery are often used in the
literature to refer to all types of pumps
and turbines regardless of whether
they utilize a rotating shaft or not.

Not all pumps have a rotating shaft;

(a) energy is supplied to this manual
tire pump by the up and down motion of a
person’s arm to pump air; (b) a similar
mechanism is used to pump water with an
old-fashioned well pump.
12
classification of Fluid Machines

13
  In radial flow the flow path is essentially radial with significant changes in
radius.
 In axial flow machines the flow path is nearly parallel to the machine centre
line and the path does not change.
 In mixed flow it is partly axial and partly radial.

Compressor:
A compressor is a machine for raising a gas – a compressible fluid – to a higher
level of pressure., actually making the air denser by cramming air into a small14
space.
15
16
17
Fluid machines may also be broadly classified as either positive-displacement
machines or dynamic machines, based on the manner in which energy transfer
occurs.
In positive-displacement machines: Fluid is directed into a closed volume.
Energy transfer to the fluid is accomplished by movement of the boundary of the
closed volume, causing the volume to expand or contract, thereby sucking fluid in
or squeezing fluid out, respectively.

(a) The human heart is an

example of a positive-
displacement pump; blood is
pumped by expansion and
contraction of heart
chambers called ventricles.
(b) The common water meter
in your house is an example
of a positive-displacement
turbine; water fills and exits a
chamber of known volume
for each revolution of the
output shaft.
18
19
20
21
Dynamic machines: There is no closed
volume; instead, rotating blades supply
or extract energy to or from the fluid.
For pumps, these rotating blades are
called impeller blades, while for turbines,
the rotating blades are called runner
blades or buckets.
Examples of dynamic pumps include
enclosed pumps and ducted pumps and
open pumps.
Examples of dynamic turbines include
enclosed turbines, such as the
hydroturbine that extracts energy from
water in a hydroelectric dam, and open
turbines such as the wind turbine that
extracts energy from the wind.
A wind turbine is a good example of a
dynamic machine of the open type; air
turns the blades, and the output shaft
drives an electric generator
22
23
24
25
26
14–2 ■ PUMPS
The mass flow rate of fluid through the pump is an obvious primary
pump performance parameter.
For incompressible flow, it is more common to use volume flow rate
rather than mass flow rate.
In the turbomachinery industry, volume flow rate is called capacity
and is simply mass flow rate divided by fluid density,

The performance of a pump is characterized additionally by its net head H,

defined as the change in Bernoulli head between the inlet and outlet of the
pump:

27
For the case in which a liquid is being pumped,
the Bernoulli head at the inlet is equivalent to
the energy grade line at the inlet.

The net head of a pump, H, is defined as the change in Bernoulli head from
inlet to outlet; for a liquid, this is equivalent to the change in the energy
grade line, H = EGLout - EGLin, relative to some arbitrary datum plane; bhp is
the brake horsepower, the external power supplied to the pump.
Pump Performance Curves and Matching
a Pump to a Piping System
Free delivery: The maximum volume flow rate through a pump occurs when
its net head is zero, H = 0; this flow rate is called the pump’s free delivery.
Shutoff head: The net head that occurs when the volume flow rate is zero,
and is achieved when the outlet port of the pump is blocked off. Under these
conditions, H is large but V is zero; the pump’s efficiency is again zero,
because the pump is doing no useful work.
Best Efficiency Point (BEP): The pump’s efficiency reaches its maximum
value somewhere between the shutoff condition and the free delivery
condition. It is notated by an asterisk (H*, bhp*, etc.).
Pump Performance Curves: Curves of H, pump, and bhp as functions of
volume flow rate are called pump performance curves (or characteristic
curves).
Operating point or duty point of the system: In a typical application,
Hrequired and Havailable match at one unique value of flow rate—this is the
operating point or duty point of the system. For steady conditions, a pump
can operate only along its performance curve.

29
30
 The useful pump
head delivered to the
fluid does four things

Equation 14–6 emphasizes the role

of a pump in a piping system;
namely, it increases (or decreases)
the static pressure, dynamic
pressure, and elevation of the fluid,
31
and it overcomes irreversible losses.
32
33
34
It is common practice in the pump
industry to offer several choices of
impeller diameter for a single pump
casing. There are several reasons
for this:
(1) to save manufacturing costs
(2) to enable capacity increase by
simple impeller replacement
(3) to standardize installation
mountings
(4) to enable reuse of equipment for
a different application

35
Example of a manufacturer’s performance plot for a family of centrifugal
pumps. Each pump has the same casing, but a different impeller diameter.
Pump Cavitation and Net Positive Suction Head
When pumping liquids, it is possible
for the local pressure inside the
pump to fall below the vapor
pressure of the liquid, Pv.
When P < Pv, vapor-filled bubbles
called cavitation bubbles appear.
The liquid boils locally, typically on
the suction side of the rotating
impeller blades where the pressure is
lowest.

Net positive suction head (NPSH): Cavitation bubbles forming and

The difference between the pump’s collapsing on the suction side of an
inlet stagnation pressure head and impeller blade.
the vapor pressure head.

39
Required net positive suction head (NPSHrequired): The minimum NPSH
necessary to avoid cavitation in the pump.

Typical pump performance curve in

The volume flow rate at which the actual
which net head and required net
NPSH and the required NPSH intersect
positive suction head are plotted
represents the maximum flow rate that
versus volume flow rate.
can be delivered by the pump without
the occurrence of cavitation.

40
41
42
43
Pumps in Series and Parallel
When faced with the need to increase volume flow rate or
pressure rise by a small amount, you might consider adding
an additional smaller pump in series or in parallel with the
original pump.

Arranging two very

dissimilar pumps in
(a) series or (b)
parallel can
sometimes lead to
problems.
44
45
46
Several identical pumps
are often run in a
parallel configuration so
that a large volume flow
rate can be achieved
when necessary. Three
parallel pumps are
shown.

47
Positive-Displacement
Pumps
Fluid is sucked into an
expanding volume and then
pushed along as that volume
contracts, but the mechanism
that causes this change in
volume differs greatly among
the various designs.
Positive-displacement pumps
are ideal for high-pressure
applications like pumping
viscous liquids or thick slurries,
and for applications where
precise amounts of liquid are to
be dispensed or metered, as in
medical applications.
Examples of positive-displacement pumps:
(a) flexible-tube peristaltic pump, (b) three-
lobe rotary pump, (c) gear pump, and (d)
double screw pump.
48
Four phases (one-eighth of a turn apart) in the operation
of a two-lobe rotary pump, a type of positive-
displacement pump. The light blue region represents a
chunk of fluid pushed through the top rotor, while the
dark blue region represents a chunk of fluid pushed
through the bottom rotor, which rotates in the opposite
direction. Flow is from left to right.

49
Positive-displacement pumps
have many advantages over
dynamic pumps.
For example, a positive-
displacement pump is better able
to handle shear sensitive liquids
since the induced shear is much
less than that of a dynamic pump
operating at similar pressure and
flow rate. A pump that can lift a liquid even when
Blood is a shear sensitive liquid, the pump itself is “empty” is called a self-
and this is one reason why priming pump.
positive-displacement pumps are
used for artificial hearts.

50
51
Dynamic Pumps
There are three main types of dynamic
pumps that involve rotating blades
called impeller blades or rotor blades,
which impart momentum to the fluid.
They are sometimes called
rotodynamic pumps or simply rotary
pumps.
Rotary pumps are classified by the
manner in which flow exits the pump:
centrifugal flow, axial flow, and mixed
flow

The impeller
(rotating portion) of
the three main
categories of
dynamic pumps:
(a) centrifugal flow,
(b) mixed flow, and
52
(c) axial flow.
Centrifugal-flow Pump: Fluid enters axially (in the same
direction as the axis of the rotating shaft) in the center of the
pump, but is discharged radially (or tangentially) along the
outer radius of the pump casing.
For this reason centrifugal pumps are also called radial-flow
pumps.
Axial-flow Pump: Fluid enters and leaves axially, typically
along the outer portion of the pump because of blockage by the
shaft, motor, hub, etc.
Mixed-flow Pump: Intermediate between centrifugal and axial,
with the flow entering axially, not necessarily in the center, but
leaving at some angle between radially and axially.

53
Centrifugal Pumps
Centrifugal pumps and blowers can be
easily identified by their snail-shaped
casing, called the scroll.
They are found all around your home;
in dishwashers, hot tubs, clothes
washers and dryers, hairdryers,
vacuum cleaners, kitchen exhaust
hoods, bathroom exhaust fans, leaf
blowers, furnaces, etc.
They are used in cars; the water pump
in the engine, the air blower in the
heater/air conditioner unit, etc.
Centrifugal pumps are ubiquitous in
industry as well; they are used in
building ventilation systems, washing
operations, cooling ponds and cooling A typical centrifugal blower with its
towers. characteristic snail-shaped scroll.

54
Impeller or Rotor: In pump terminology, the rotating assembly that consists
of the shaft, the hub, the impeller blades, and the impeller shroud.
A shroud often surrounds the impeller blades to increase blade stiffness.

Side view and frontal view of a typical centrifugal pump. Fluid enters axially in
the middle of the pump (the eye), is flung around to the outside by the rotating
blade assembly (impeller), is diffused in the expanding diffuser (scroll), and is
discharged out the side of the pump. We define r1 and r2 as the radial locations
of the impeller blade inlet and outlet, respectively; b1 and b2 are the axial blade 55
widths at the impeller blade inlet and outlet, respectively.
There are three types of centrifugal pump based on impeller
blade geometry: Backward-inclined blades, radial blades,
and forward-inclined blades.
Centrifugal pumps with backward-inclined blades are the
most common. These yield the highest efficiency of the
three because fluid flows into and out of the blade passages
with the least amount of turning.
Centrifugal pumps with radial blades (also called straight
blades) have the simplest geometry and produce the
largest pressure rise of the three.
Centrifugal pumps with forward-inclined blades produce a
pressure rise that is nearly constant.

The three main types of

centrifugal pumps are those
with (a) backward-inclined
blades, (b) radial blades, and
(c) forward-inclined blades;
(d) comparison of net head
and brake horsepower
performance curves for the
three types of centrifugal 56
pumps.
Volume flow rate:

Close-up frontal view of the simplified

centrifugal flow pump used for elementary
analysis of the velocity vectors. Absolute
velocity vectors of the fluid are shown as
bold arrows. It is assumed that the flow is
Close-up side view of the simplified
everywhere tangent to the blade surface
centrifugal flow pump used for elementary
when viewed from a reference frame
analysis of the velocity vectors; V1, n and
rotating with the blade, as indicated by the
V2, n are defined as the average normal
relative velocity vectors.
(radial) components of velocity at radii r1
and r2, respectively.
 Shaft torque is equal to the change in
moment of momentum from inlet to outlet, as
given by the Euler turbomachine equation
(also called Euler’s turbine formula)

Euler turbomachine
equation:

Alternative form, Euler turbomachine

equation:

Net head:
Control volume (shaded) used for
angular momentum analysis of a
centrifugal pump; absolute
tangential velocity components V1, t
58
and V2, t are labeled.
59
60
Bernoulli equation in a
rotating reference frame:

The law of cosines is

utilized in the analysis of
a centrifugal pump.
61
For the approximation of flow
through an impeller with no
irreversible losses, it is often more
convenient to work with a relative
frame of reference rotating with the
impeller; in that case, the Bernoulli
equation gets an additional term,
as indicated in Eq. 14–22.
Close-up frontal view of the
velocity vectors at the impeller
blade inlet. The absolute velocity
vector is shown as a bold arrow. 62
63
64
65
66
(a) A centrifugal pump impeller with too few blades leads to excessive circulatory
flow loss—the tangential velocity at outer radius r2 is smaller in the gaps between
blades than at the trailing edges of the blades (absolute tangential velocity vectors
are shown).
(b) On the other hand, since real impeller blades have finite thickness, an impeller
with too many blades leads to passage losses due to excessive flow blockage and
large skin friction drag (velocity vectors in a frame of reference rotating with the
impeller are shown exiting one blade row). The bottom line is that pump engineers
must optimize both blade shape and number of blades.
While the predicted performance is close to
the actual performance at design
conditions, the two curves deviate
substantially away from design conditions.
At all volume flow rates, the actual net
head is lower than the predicted net head.
This is due to irreversible effects such as;
- friction along blade surfaces,
- leakage of fluid between the blades and
the casing,
- prerotation (swirl) of fluid in the region of
the eye,
- flow separation on the leading edges of
the blades (shock losses) or in the
expanding portions of the flow passages, Net head as a function of volume
circulatory flow loss, flow rate for the pump of Example
14-6. The difference between
- passage loss,
predicted and actual performance is
- irreversible dissipation of swirling eddies due to unaccounted irreversibilities in
in the volute, among other things. the prediction.
68
Axial Pumps
Axial pumps do not utilize so-called
centrifugal forces. Instead, the
impeller blades behave more like the
wing of an airplane, producing lift by
changing the momentum of the fluid
as they rotate.
The lift force on the blade is caused
by pressure differences between the The blades of an axial-flow pump
top and bottom surfaces of the blade, behave like the wing of an airplane.
and the change in flow direction The air is turned downward by the
leads to downwash (a column of wing as it generates lift force FL.
descending air) through the rotor
plane.
From a time-averaged perspective,
there is a pressure jump across the
rotor plane that induces a downward
airflow.
Downwash and pressure rise across
the rotor plane of a helicopter, which
is a type of axial-flow pump. 69
Imagine turning the rotor plane vertically; we now have a propeller.
Both the helicopter rotor and the airplane propeller are examples of open axial-
flow fans, since there is no duct or casing around the tips of the blades.
The casing around the house fan also acts as a short duct, which helps to direct
the flow and eliminate some losses at the blade tips.
The small cooling fan inside your computer is typically an axial-flow fan; it looks like
a miniature window fan and is an example of a ducted axial-flow fan.

Axial-flow fans may

be open or ducted:
(a) a propeller is an
open fan, and (b) a
computer cooling fan
is a ducted fan.
70
A well-designed rotor blade or propeller
blade has twist, as shown by the blue cross-
sectional slices through one of the three
blades; blade pitch angle  is higher at the
root than at the tip because the tangential
speed of the blade increases with radius. 71
Equation 14–27 is not exact for several
reasons:
First, the rotating motion of the rotor
introduces some swirl to the airflow. This
reduces the effective tangential speed of the
blade relative to the incoming air.
Second, since the hub of the rotor is of finite
size, the air accelerates around it, causing
the air speed to increase locally at cross
sections of the blade close to the root.
Third, the axis of the rotor or propeller may
The rotating blades of a rotor or
not be aligned exactly parallel to the incoming
propeller induce swirl in the
air.
surrounding fluid.
Finally, the air speed itself is not easily
determined because it turns out that the air
accelerates as it approaches the whirling
rotor.
72
73
74
 Unlike centrifugal fans, brake horsepower
tends to decrease with flow rate.
The efficiency curve leans more to the right
compared to that of centrifugal fans.
The result is that efficiency drops off rapidly
for volume flow rates higher than that at the
best efficiency point.
The net head curve also decreases
continuously with flow rate (although there
are some wiggles), and its shape is much
Typical fan performance curves different than that of a centrifugal flow fan.
for a propeller (axial-flow) fan.
If the head requirements are not severe, propeller fans can be operated beyond
the point of maximum efficiency to achieve higher volume flow rates.
Since bhp decreases at high values of flow rate, there is not a power penalty
when the fan is run at high flow rates. For this reason it is tempting to install a
slightly undersized fan and push it beyond its best efficiency point.
At the other extreme, if operated below its maximum efficiency point, the flow may
be noisy and unstable, which indicates that the fan may be oversized.
It is usually best to run a propeller fan at, or slightly above, its maximum efficiency
point.
 When used to move flow in a duct, a single-
impeller axial-flow fan is called a tube-axial
fan.
A second rotor that rotates in the opposite
direction can be added in series with the
existing rotor to form a pair of counter-rotating
rotor blades; such a fan is called a counter-
rotating axial-flow fan. Alternatively, a set of
stator blades can be added either upstream
or downstream of the rotating impeller.
As implied by their name, stator blades are
stationary (nonrotating) guide vanes that
simply redirect the fluid.
An axial-flow fan with a set of rotor blades (the
impeller or the rotor) and a set of stator
blades called vanes (the stator) is called a
vane-axial fan.
A tube-axial fan (a) imparts swirl to
the exiting fluid, while (b) a
counterrotating axial-flow fan and
(c) a vane-axial fan are designed
76
to remove the swirl.
 Analysis of a vane-axial
flow fan at radius r using
the two-dimensional
blade row
approximation; (a)
overall view, (b)
absolute reference
frame, and (c) reference
Axial-flow fans: (a) a belt-driven tube-axial fan without frame relative to the
stator blades, and (b) a direct-drive vane-axial fan with rotating rotor blades
stator blades to reduce swirl and improve efficiency. (impeller).
Typical fan
performance curves
for a vane-axial flow
fan.

A multistage axial-
flow pump consists
of two or more
78
rotor–stator pairs.
Pratt & Whitney PW4000 turbofan engine; an
example of a multistage axial-flow turbomachine.
79
80
81
82
14–3 ■ PUMP SCALING LAWS
Dimensional Analysis

Dimensional analysis of a pump.

83
 When plotted in terms of dimensionless
Dimensional analysis is useful for pump parameters, the performance curves
scaling two geometrically similar of all pumps in a family of geometrically
pumps. If all the dimensionless similar pumps collapse onto one set of
pump parameters of pump A are nondimensional pump performance curves.
equivalent to those of pump B, the Values at the best efficiency point are
two pumps are dynamically similar. indicated by asterisks.
When a small-scale model is
tested to predict the performance
of a full-scale prototype pump,
the measured efficiency of the
model is typically somewhat
lower than that of the prototype.
Empirical correction equations
such as Eq. 14–34 have been
developed to account for the
improvement of pump efficiency
with pump size.

85
Pump Specific Speed

Pump specific speed is used to characterize the

operation of a pump at its optimum conditions
(best efficiency point) and is useful for
preliminary pump selection and/or design.

Even though pump specific speed is a

dimensionless parameter, it is common
practice to write it as a dimensional
86
quantity using an inconsistent set of units.
 Maximum efficiency as a function of
pump specific speed for the three
main types of dynamic pump. The
horizontal scales show
nondimensional pump specific speed
Conversions between the dimensionless, (NSp), pump specific speed in
conventional U.S., and conventional customary U.S. Units (NSp, US), and
European definitions of pump specific pump specific speed in customary
speed. Numerical values are given to four European units (NSp, Eur).
significant digits. The conversions for NSp,US
assume standard earth gravity.
88
Affinity Laws
Equations 14–38 apply to both pumps and
turbines.
States A and B can be any two homologous
states between any two geometrically
similar turbomachines, or even between two
homologous states of the same machine.
Examples include changing rotational speed
or pumping a different fluid with the same
pump.

89
90
91
92
93
94
14–4 ■ TURBINES
Turbines have been used for centuries to convert
freely available mechanical energy from rivers
and wind into useful mechanical work, usually
through a rotating shaft.
The rotating part of a hydroturbine is called the
runner.
When the working fluid is water, the
turbomachines are called hydraulic turbines or
hydroturbines.
When the working fluid is air, and energy is
extracted from the wind, the machine is called a
wind turbine.
Most people use the word windmill to describe
any wind turbine, whether used to grind grain,
pump water, or generate electricity.
The turbomachines that convert energy from the
steam into mechanical energy of a rotating shaft
are called steam turbines.
Turbines that employ a compressible gas as the
95
working fluid is gas turbine.
In general, energy-producing turbines have somewhat higher overall
efficiencies than do energy-absorbing pumps.
Large hydroturbines achieve overall efficiencies above 95 percent, while the
best efficiency of large pumps is a little more than 90 percent.
There are several reasons for this:
First, pumps normally operate at higher rotational speeds than do turbines;
therefore, shear stresses and frictional losses are higher.
Second, conversion of kinetic energy into flow energy (pumps) has
inherently higher losses than does the reverse (turbines).
Third, turbines (especially hydroturbines) are often much larger than pumps,
and viscous losses become less important as size increases.
Finally, while pumps often operate over a wide range of flow rates, most
electricity-generating turbines run within a narrower operating range and at a
controlled constant speed; they can therefore be designed to operate most
efficiently at those conditions.
As with pumps, we classify turbines into two broad categories,
positive displacement and dynamic.
Positive-displacement turbines are small devices used for volume flow rate
measurement, while dynamic turbines range from tiny to huge and are used
for both flow measurement and power production. 96
Positive-Displacement Turbines
A positive-displacement turbine may be
thought of as a positive-displacement pump
running backward—as fluid pushes into a closed
volume, it turns a shaft or displaces a
reciprocating rod. The closed volume of fluid is
then pushed out as more fluid enters the device.
There is a net head loss through the positive-
displacement turbine; energy is extracted from
the flowing fluid and is turned into mechanical
energy.
However, positive-displacement turbines are
generally not used for power production, but
rather for flow rate or flow volume measurement.

The nutating disc fluid flowmeter is a type of

positive-displacement turbine used to
measure volume flow rate: (a) cutaway view
and (b) diagram showing motion of the
nutating disc. This type of flowmeter is
97
commonly used as a water meter in homes.
Dynamic Turbines
Dynamic turbines are used both as flow measuring devices and as power generators.
Hydroturbines utilize the large elevation change across a dam to generate electricity,
and wind turbines generate electricity from blades rotated by the wind. There are two
basic types of dynamic turbine—impulse and reaction.
Impulse turbines require a higher head, but can operate with a smaller volume flow rate.
Reaction turbines can operate with much less head, but require a higher volume flow
rate.

Examples of dynamic turbines: (a) a typical three-cup anemometer used

to measure wind speed, and (b) a Piper PA28 research airplane with
turbines designed to extract energy from the wing tip vortices.
Impulse Turbines
In an impulse turbine, the fluid is sent
through a nozzle so that most of its
available mechanical energy is converted
into kinetic energy.
The high-speed jet then impinges on
bucket-shaped vanes that transfer energy
to the turbine shaft.
The modern and most efficient type of
impulse turbine is Pelton turbine and the
rotating wheel is now called a Pelton
wheel.

Schematic diagram of a Pelton-type impulse

turbine; the turbine shaft is turned when high-
speed fluid from one or more jets impinges on
buckets mounted to the turbine shaft. (a) Side
view, absolute reference frame, and (b)
bottom view of a cross section of bucket n,
99
rotating reference frame.
A close-up view of a Pelton
wheel showing the detailed
design of the buckets; the
electrical generator is on the
right. This Pelton wheel is on
display at the Waddamana
Power Station Museum near
Bothwell, Tasmania.

A view from the bottom of an

operating Pelton wheel
illustrating the splitting and
turning of the water jet in the
bucket. The water jet enters from
the left, and the Pelton wheel is
turning to the right.
101
Reaction Turbines
The other main type of energy-producing
hydroturbine is the reaction turbine, which
consists of fixed guide vanes called stay vanes,
adjustable guide vanes called wicket gates, and
rotating blades called runner blades.
Flow enters tangentially at high pressure, is
turned toward the runner by the stay vanes as it
moves along the spiral casing or volute, and
then passes through the wicket gates with a
large tangential velocity component.

A reaction turbine differs significantly

from an impulse turbine; instead of
using water jets, a volute is filled with
swirling water that drives the runner.
For hydroturbine applications, the axis
is typically vertical. Top and side views
are shown, including the fixed stay
102
vanes and adjustable wicket gates.
There are two main types of reaction turbine—Francis and Kaplan.
The Francis turbine is somewhat similar in geometry to a centrifugal or mixed-
flow pump, but with the flow in the opposite direction.
The Kaplan turbine is somewhat like an axial-flow fan running backward.
We classify reaction turbines according to the angle that the flow enters the
runner. If the flow enters the runner radially, the turbine is called a Francis radial-
flow turbine.
If the flow enters the runner at some angle between radial and axial, the turbine is
called a Francis mixed-flow turbine. The latter design is more common.
Some hydroturbine engineers use the term “Francis turbine” only when
there is a band on the runner. Francis turbines are most suited for heads that lie
between the high heads of Pelton wheel turbines and the low heads of Kaplan
turbines.
A typical large Francis turbine may have 16 or more runner blades and can
achieve a turbine efficiency of 90 to 95 percent.
If the runner has no band, and flow enters the runner partially turned, it is called a
propeller mixed-flow turbine or simply a mixed-flow turbine. Finally, if the flow
is turned completely axially before entering the runner, the turbine is called an
axial-flow turbine.
103
Kaplan turbines are called double regulated because the flow rate is controlled in two
ways—by turning the wicket gates and by adjusting the pitch on the runner blades.
Propeller turbines are nearly identical to Kaplan turbines except that the blades are
fixed (pitch is not adjustable), and the flow rate is regulated only by the wicket gates
(single regulated).
Compared to the Pelton and Francis turbines, Kaplan turbines and propeller turbines
are most suited for low head, high volume flow rate conditions.
Their efficiencies rival those of Francis turbines and may be as high as 94 percent.
105
106
107
Typical setup and terminology for a hydroelectric plant
that utilizes a Francis turbine to generate electricity;
drawing not to scale. The Pitot probes are shown for
illustrative purposes only.

The net head of a turbine is defined as the difference

between the energy grade line just upstream of the turbine
and the energy grade line at the exit of the draft tube.
108
 (a) An aerial view of Hoover Dam and (b) the top
By definition, efficiency must (visible) portion of several of the parallel electric
always be less than unity. generators driven by hydraulic turbines at Hoover
The efficiency of a turbine is Dam.
the reciprocal of the efficiency
of a pump.

109
Relative and absolute velocity Relative and absolute velocity vectors
vectors and geometry for the and geometry for the inner radius of
outer radius of the runner of a the runner of a Francis turbine.
Francis turbine. Absolute velocity Absolute velocity vectors are bold.
vectors are bold.

110
In some Francis mixed-flow
turbines, high-power, high-
volume flow rate conditions
sometimes lead to reverse
swirl, in which the flow exiting
the runner swirls in the
direction opposite to that of the
runner itself, as sketched here.

111
112
113
114
115
Gas and Steam Turbines
In a coal or nuclear power plant,
high-pressure steam is produced
by a boiler and then sent to a
steam turbine to produce
electricity.
Because of reheat, regeneration,
and other efforts to increase
overall efficiency, these steam
turbines typically have two
stages (high pressure and low
pressure).
Most power plant steam turbines
are multistage axial-flow
devices.
There are also stator vanes
(called nozzles) that direct the The turbine blades (called buckets) of a typical
flow between each set of turbine two-stage steam turbine used in a coal or
blades (called buckets). nuclear power plant. The flow is from left to right,
with the high-pressure stage on the left and the
low-pressure stage on the right. 116
A gas turbine generator is similar to a jet engine except that instead of providing
thrust, the turbomachine is designed to transfer as much of the fuel’s energy as
possible into the rotating shaft, which is connected to an electric generator.
Gas turbines used for power generation are typically much larger than jet engines.
A significant gain in efficiency is realized as overall turbine size increases.

117
Wind Turbines
As global demand for energy increases, the supply of fossil fuels diminishes
and the price of energy continues to rise.
To keep up with global energy demand, renewable sources of energy such
as solar, wind, wave, tidal, hydroelectric, and geothermal must be tapped
more extensively.
In this section we concentrate on wind turbines used to generate electricity.
We note the distinction between the terms windmill used for mechanical
power generation (grinding grain, pumping water, etc.) and wind turbine
used for electrical power generation.
Although the wind is “free” and renewable, modern wind turbines are
expensive and suffer from one obvious disadvantage compared to most
other power generation devices – they produce power only when the wind is
blowing, and the power output of a wind turbine is thus inherently unsteady.
Wind turbines need to be located where the wind blows, which is often far
from traditional power grids, requiring construction of new high-voltage
power lines.
118
We generally categorize wind turbines by the orientation of their axis of rotation:
horizontal axis wind turbines (HAWTs)
vertical axis wind turbines (VAWTs).
An alternative way to categorize them is by the mechanism that provides torque
to the rotating shaft: lift or drag.
So far, none of the VAWT designs or drag-type designs has achieved the
efficiency or success of the lift-type HAWT.
This is why the vast majority of wind turbines being built around the world are of
this type, often in clusters affectionately called wind farms.
For this reason, the lift-type HAWT is the only type of wind turbine discussed in
any detail in this section.

119
Various wind
turbine designs
and their
categorization.
120
Various wind turbine designs and their categorization.

121
Various wind turbine designs and their categorization.
122
Various wind turbine designs and their categorization.

123
(a) Wind farms, like this one on Altamont Pass in
California, are popping up all over the world to help
reduce the global demand for fossil fuels. (b)
Some wind turbines are even being installed on
buildings!

124
Cut-in speed: The minimum wind speed at which useful power can be
generated.
Rated speed: The wind speed that delivers the rated power, usually the
maximum power.
Cut-out speed: The maximum wind speed at which the wind turbine is
designed to produce power. At wind speeds greater than the cut-out speed,
the turbine blades are stopped by some type of braking mechanism to avoid
damage and for safety issues. The short section of dashed blue line indicates
the power that would be produced if cut-out were not implemented.

Typical qualitative wind-

turbine power
performance curve with
definitions of cut-in,
rated, and cut-out
speeds.

125
 Available wind
power

Disk area A: The circular area swept out

by the turbine blades as they rotate.

Wind power
density

100 W/m2, poor

400 W/m2, good
700 W/m2, great
Energy pattern
126
factor
Aerodynamic efficiency: The fraction of available wind power that is
extracted by the turbine blades. This efficiency is commonly called the
power coefficient, CP,

The large and small control volumes for analysis

of ideal wind turbine performance bounded by an
axisymmetric diverging stream tube. 127
 Qualitative sketch of
average streamwise
velocity and pressure
profiles through a wind
turbine.

The average velocity of the air through an ideal

wind turbine is the arithmetic average of the far
upstream and far downstream velocities.

Betz limit
128
Performance (power coefficient) of various types of wind
turbines as a function of the ratio of turbine blade tip speed
to wind speed. So far, no design has achieved better
performance than the horizontal axis wind turbine (HAWT).
129
130
14–5 ■ TURBINE SCALING LAWS

The main variables used for

dimensional analysis of a turbine.
The characteristic turbine diameter
D is typically either the runner
diameter Drunner or the discharge
diameter Ddischarge.

131
 In practice, hydroturbine engineers
generally find that the actual increase in
efficiency from model to prototype is only
about two-thirds of the increase given by
this equation.

Dimensional analysis is useful for

scaling two geometrically similar
turbines. If all the dimensionless turbine
parameters of turbine A are equivalent
to those of turbine B, the two turbines
are dynamically similar.

132
133
134
Turbine Specific Speed

A pump–turbine is used by
some power plants for energy
storage: (a) water is pumped
by the pump–turbine during
periods of low demand for
power, and (b) electricity is
generated by the pump–
turbine during periods of high
135
demand for power.
The runner of a pump–turbine used at the Yards Creek
pumped storage station in Blairstown, NJ. There are
seven runner blades of outer diameter 5.27 m. The turbine
rotates at 240 rpm and produces 112 MW of power at a
volume flow rate of 56.6 m3/s from a net head of 221 m.

136
Conversions between the dimensionless
and the conventional U.S. definitions of
turbine specific speed. Numerical values
are given to four significant digits. The
conversions assume earth gravity and
water as the working fluid.

Capacity specific
speed

137
Maximum efficiency as a function of turbine specific speed for the three main types
of dynamic turbine. Horizontal scales show nondimensional turbine specific speed
(NSt) and turbine specific speed in customary U.S. units (NSt, US). Sketches of the
blade types are also provided on the plot for reference.

138
139
• CLASSIFICATIONS AND TERMINOLOGY
• PUMPS
 Pump Performance Curves and Matching a Pump to a
Piping System
 Pump Cavitation and Net Positive Suction Head
 Pumps in Series and Parallel
 Positive-Displacement Pumps
 Dynamic Pumps
 Centrifugal Pumps
 Axial Pumps
• PUMP SCALING LAWS
 Dimensional Analysis
Summary
 Pump Specific Speed
 Affinity Laws
• TURBINES
 Positive-Displacement Turbines
 Dynamic Turbines
 Impulse Turbines
 Reaction Turbines
 Gas and Steam Turbines
 Wind Turbines
• TURBINE SCALING LAWS
 Dimensionless Turbine Parameters
 Turbine Specific Speed