المحاضرة الثالثة عشر
SHEET METALWORKING
1. Cutting Operations
2. Bending Operations
3. Drawing
4. Other Sheet Metal Forming Operations
5. Dies and Presses for Sheet Metal
Processes
6. Sheet Metal Operations Not Performed
on Presses
7. Bending of Tube Stock
Sheet Metalworking Defined
Cutting and forming operations
performed on relatively thin sheets
of metal
Thickness of sheet metal = 0.4 mm
(1/64 in) to 6 mm (1/4 in)
Thickness of plate stock > 6 mm
Operations usually performed as
cold working
Sheet and Plate Metal Products
Sheet and plate metal parts for consumer and
industrial products such as
Automobiles and trucks
Airplanes
Railway cars and locomotives
Farm and construction equipment
Small and large appliances
Office furniture
Computers and office equipment
Advantages of Sheet Metal Parts
High strength
Good dimensional accuracy
Good surface finish
Relatively low cost
Economical mass production for
large quantities
Sheet Metalworking Terminology
Punch ‑ and ‑ die - tooling to
perform cutting, bending, and
drawing
Stamping press - machine tool
that performs most sheet metal
operations
Stampings - sheet metal
products
Basic Types of Sheet Metal Processes
1. Cutting
Shearing to separate large sheets
Blanking to cut part perimeters out of sheet
metal
Punching to make holes in sheet metal
2. Bending
Straining sheet around a straight axis
3. Drawing
Forming of sheet into convex or concave
shapes
Sheet Metal Cutting
Figure 20.1 Shearing of sheet metal between two cutting edges:
(1) just before the punch contacts work; (2) punch begins to
push into work, causing plastic deformation;
Sheet Metal Cutting
Figure 20.1 Shearing of sheet metal between two cutting edges:
(3) punch compresses and penetrates into work causing a
smooth cut surface; (4) fracture is initiated at the opposing
cutting edges which separates the sheet.
Characteristics of shearing edg
The sheared edges of the sheet have characteristic features as in Figure 20.2. At the top of
the cut surface is a region called the rollover. This corresponds to the depression made by
the punch in the work prior to cutting. It is where initial plastic deformation occurred in the
work. Just below the rollover is a relatively smooth region called the burnish. This results
from penetration of the punch into the work before fracture began. Beneath the burnish is
the fractured zone, a relatively rough surface of the cut edge where continued downward
movement of the punch caused fracture of the metal. Finally, at the bottom of the edge is a
burr, a sharp corner on the edge caused by elongation of the metal during final separation of
the two pieces.
Shearing, Blanking, and Punching
Three principal operations in pressworking that
cut sheet metal:
Shearing
Blanking
Punching
Shearing
Sheet metal cutting operation along a straight line
between two cutting edges
Typically used to cut large sheets
Figure 20.3 Shearing operation: (a) side view of the
shearing operation; (b) front view of power shears
equipped with inclined upper cutting blade.
Shearing
Shearing is a sheet-metal cutting operation along a
straight line between two cutting edges, as shown
in Figure 20.3(a).
Shearing is typically used to cut large sheets into
smaller sections for subsequent pressworking
operations. It is performed on a machine called a
power shears, or squaring shears.
The upper blade of the power shears is often
inclined, as shown in Figure 20.3(b), to reduce the
required cutting force.
Rotary Shearing
Rotary blades
Blanking and Punching
Blanking - sheet metal cutting to separate piece
(called a blank) from surrounding stock
Punching - similar to blanking except cut piece is
scrap, called a slug
Figure 20.4 (a) Blanking and (b) punching.
Blanking and Punching
Blanking involves cutting of the sheet metal
along a closed outline in a single step to
separate the piece from the surrounding
stock, as in Figure 20.4(a). The part that is cut
out is the desired product in the operation and
is called the blank.
Punching is similar to blanking except that it
produces a hole, and the separated piece is
scrap, called the slug. The remaining stock is
the desired part. The distinction is illustrated
in Figure 20.4(b).
النهاية
