RK3588调试EDP

RYF6666

已于 2023-11-24 18:13:18 修改

阅读量2.6k

点赞数 4

CC 4.0 BY-SA版权

文章标签： android

于 2023-11-24 18:12:22 首次发布

本文链接：https://blog.csdn.net/RYF6666/article/details/134603713

平台：RK3588 Android12

问题：点一个EDP屏

1、首先肯定是背光了

从原理图上看，无非就是一个使能一个PWM，顺着找到主控那边配一下就好了，这里是2_B5拉低，用的是PWM1

++	backlight: backlight {
++		compatible = "pwm-backlight";
++		pwms = <&pwm1 0 25000 0>;
++		enable-gpios = <&gpio2 RK_PB5 GPIO_ACTIVE_LOW>;
++		default-brightness-level = <200>;
++	};

++		&pwm1 {
++			status = "okay";
++		};

背光配好了再配置一下edp就行了

看样子把VCC3V3_LCD配好就ok了，所以继续往下查原理图；

一查发现，这个使能脚居然和另外一个背光用的是同一个，但是原理图上却没有把这个背光画在一起，所以其实只需要把这个 LCD_PWREN_H拉高一下，就可以得到一组背光以及edp了。

++	panel-edp {
++		status = "okay";
++		compatible = "innolux,p120zdg-bf4", "simple-panel";
++		backlight = <&backlight>;
++		power-supply = <&vcc3v3_lcd_n>;
++		prepare-delay-ms = <120>;
++		//enable-gpios = <&gpio2 RK_PB5 GPIO_ACTIVE_LOW>;
++		enable-delay-ms = <120>;
++		unprepare-delay-ms = <500>;
++		disable-delay-ms = <120>;
++		width-mm = <254>;
++		height-mm = <169>;
++
++		panel-timing {
++			clock-frequency = <72300000>; 
++			hactive = <1366>;			 
++			vactive = <768>;
++			hback-porch = <160>;		  	  
++			hfront-porch = <80>;	
++			hsync-len = <20>;
++			vback-porch = <10>;			
++			vfront-porch = <8>;		  
++			vsync-len = <4>;
++			hsync-active = <0>;
++			vsync-active = <0>;
++			de-active = <0>;
++			pixelclk-active = <0>;
++		};
++
++		port {
++			panel_in_edp: endpoint {
++				remote-endpoint = <&edp_out_panel>;
++			};
++		};
++	};

++		&edp0 {
++			force-hpd;
++			status = "okay";
++		
++			ports {
++				port@1 {
++					reg = <1>;
++		
++					edp_out_panel: endpoint {
++						remote-endpoint = <&panel_in_edp>;
++					};
++				};
++			};
++		};
++		
++		&edp0_in_vp2 {
++			status = "okay";
++		};
++		
++		&route_edp0 {
++			connect = <&vp2_out_edp0>;
++			status = "okay";
++		};
++		
++		&hdptxphy0{
++			lane-polarity-invert = <0 1 0 0>;
++			status = "okay";
++		};

++	vcc3v3_lcd_n: vcc3v3-lcd0-n {
++		compatible = "regulator-fixed";
++		regulator-name = "vcc3v3_lcd0_n";
++		regulator-boot-on;
++		enable-active-high;
++		gpio = <&gpio4 RK_PA4 GPIO_ACTIVE_HIGH>;
++		vin-supply = <&vcc_3v3_s3>;
++	};

大功告成了！