CC1310 CCS 记录20241107

导入工程后失败

环境为CCS 10.4导入为12.8

Description    Resource    Path    Location    Type


Referenced project 'tirtos_builds_CC1310_LAUNCHXL_release_ccs' does not exist in the workspace. Project 'CC1310_DataReceiver_awce' may not build as expected.    CC1310_DataReceiver_awce        CC1310_DataReceiver_awce    Problem

导入的文件问题。

See details below... 
    Project 'tirtos_builds_CC1310_LAUNCHXL_release_ccs', referenced from 'CC1310_DataReceiver_awce', could not be found. Please import this project manually.
 

升级下看看。
Messages/issues which may require your attention were encountered while importing theproject(s).Invalid project description.X

"../CC1310_LAUNCHXL.c", line 39: fatal error: could not open source file "stdbool.h" (no directories in search list


>> Compilation failure
subdir_rules.mk:9: recipe for target 'main_tirtos.obj' failed
"../main_tirtos.c", line 4: fatal error: could not open source file "stdint.h" (no directories in search list)

导入配置头文件

出现这个242错误

Error connecting to the target:
(Error -242 @ 0x0)
A router subpath could not be accessed.
The board configuration file is probably incorrect.
(Emulation package 20.0.0.3178)

安装所需的编译器 没有效果

1、 打开菜单Help -> Install New Software

向工程添加RTSC配置文件 没有效果

1、选定工程,选择File->New->RTSC Configuration File

gmake: *** No rule to make target 'D:/1.LFD/code/CC1310_DataReceiver_tirtos_ccs/tirtos_builds_CC1310_LAUNCHXL_release_ccs/Debug/configPkg/config.bld', needed by 'configPkg/compiler.opt'.

gmake: *** No rule to make target

都没有效果

        太多问题了,开始新建空白工程,然后复制.C .H 文件过去

锤子成功了。但是调试失败了。

targetConfig重新配置为cJTAG(1149.7)4-pin standard mode

修改JTAG配置并没什么用


An error occurred while hard opening the controller.

-----[An error has occurred and this utility has aborted]--------------------

This error is generated by TI's USCIF driver or utilities.

The value is '-242' (0xffffff0e).
The title is 'SC_ERR_ROUTER_ACCESS_SUBPATH'.

The explanation is:
A router subpath could not be accessed.
The board configuration file is probably incorrect.

[End: Texas Instruments XDS110 USB Debug Probe]


The scan-path will be reset by toggling the JTAG TRST signal.
The controller is the XDS110 with USB interface.
The link from controller to target is direct (without cable).
The software is configured for XDS110 features.
The controller cannot monitor the value on the EMU[0] pin.
The controller cannot monitor the value on the EMU[1] pin.
The controller cannot control the timing on output pins.
The controller cannot control the timing on input pins.
The scan-path link-delay has been set to exactly '0' (0x0000).

An error occurred while hard opening the controller.

重新安装软件10.4版本的,这里之前只勾一项,后面导入工程一直失败,建议全部勾上,

烧录器和板子再其他电脑10.4的环境下仿真调试通过。

12.8可能有问题。换成10.4验证下

安装为10.4仍然有问题。

过了一天新建了个工程发现没有问题了。

开始找问题了。

最终是把CC1310F128.ccmxl这个给删了,重新建了个解决问题。

另外排查出10Pin的接口线也有问题。这就是最不可能出现问题的点了。

See details below... 
    spimaster_CC1310_LAUNCHXL_tirtos_ccs
        No XDCtools, equivalent to the specified version '3.51.999', are available - defaulting to '3.62.1.15_core'.
 

导入工程文件错误很多是因为少导入了工程文件。

将这个放在同一文件夹导入  问题解决

评论
添加红包

请填写红包祝福语或标题

红包个数最小为10个

红包金额最低5元

当前余额3.43前往充值 >
需支付:10.00
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明:

1.余额是钱包充值的虚拟货币,按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载,可以购买VIP、付费专栏及课程。

余额充值