Données de conception structurelle 3D
Transféré par
Wilkenn TuazonDonnées de conception structurelle 3D
Transféré par
Wilkenn TuazonFigure 1 3D RENDERED VIEW
< Control Data >
*** CONTROL DATA
Panel Zone Effect : Do not Calculate
Unit System : KN, M
Definition of Frame
- X Direction of Frame : Braced I Non-sway
- Y Direction of Frame : Braced I Non-sway
- Design Type : 3-D
Design Code
- Steel : AISC(15th)-LRFD16
- Concrete : ACI318M-14
- SRC : SSRC79
< Static Loadcase >
*** LOAD CASE DATA
NO NAME TYPE SELF WEIGHT FACTOR DESCRIPTION
X Y Z
-------- -------------------- ---------- ------ ------ ------ -------------------------------
----
1 DL D 0.000 0.000 0.000
2 LL L 0.000 0.000 0.000
3 EX+ E 0.000 0.000 0.000
4 EY+ E 0.000 0.000 0.000
5 RLL LR 0.000 0.000 0.000
6 WL W 0.000 0.000 0.000
7 SELF WEIGHT D 0.000 0.000 -1.000
< Story >
*** STORY DATA
NAME LEVEL HEIGHT FLOOR DIAPHRAGM
--------------- ---------- ---------- -------------------------
Roof 8.400 0.000 Do not consider
10F 8.237 0.163 Do not consider
9F 8.073 0.163 Do not consider
8F 7.910 0.163 Do not consider
7F 7.747 0.163 Do not consider
6F 7.584 0.163 Do not consider
5F 7.420 0.163 Do not consider
4F 7.200 0.220 Do not consider
3F 3.600 3.600 Consider
2F 0.000 3.600 Consider
1F -4.200 4.200 Do not consider
< Node >
*** NODE DATA
NO X Y Z TEMPERATURE
-------- ------------ ------------ ------------ ------------
1 0 0 0 0
2 2.622 0 0 0
3 7.372 0 0 0
4 12.12 0 0 0
5 16.87 0 0 0
6 0 3.5 0 0
7 2.622 3.5 0 0
8 7.372 3.5 0 0
9 12.12 3.5 0 0
10 16.87 3.5 0 0
11 0 8.62 0 0
12 2.622 8.62 0 0
13 7.372 8.62 0 0
14 12.12 8.62 0 0
15 16.87 8.62 0 0
16 0 13.97 0 0
17 2.622 13.97 0 0
18 7.372 13.97 0 0
19 12.12 13.97 0 0
20 16.87 13.97 0 0
21 0 0 3.6 0
22 2.622 0 3.6 0
23 7.372 0 3.6 0
24 12.12 0 3.6 0
25 16.87 0 3.6 0
26 0 3.5 3.6 0
27 2.622 3.5 3.6 0
28 7.372 3.5 3.6 0
29 12.12 3.5 3.6 0
30 16.87 3.5 3.6 0
31 0 8.62 3.6 0
32 2.622 8.62 3.6 0
33 7.372 8.62 3.6 0
34 12.12 8.62 3.6 0
35 16.87 8.62 3.6 0
36 0 13.97 3.6 0
37 2.622 13.97 3.6 0
38 7.372 13.97 3.6 0
39 12.12 13.97 3.6 0
40 16.87 13.97 3.6 0
58 12.12 0 7.2 0
59 16.87 0 7.2 0
60 12.12 3.5 7.2 0
61 16.87 3.5 7.2 0
62 0 8.62 7.2 0
63 2.622 8.62 7.2 0
64 7.372 8.62 7.2 0
65 12.12 8.62 7.2 0
66 16.87 8.62 7.2 0
67 0 13.97 7.2 0
68 2.622 13.97 7.2 0
69 7.372 13.97 7.2 0
70 12.12 13.97 7.2 0
71 16.87 13.97 7.2 0
72 12.12 5.207 3.6 0
73 12.12 6.913 3.6 0
74 16.87 5.207 3.6 0
75 16.87 6.913 3.6 0
76 14.5 6.913 3.6 0
77 14.5 5.207 3.6 0
78 14.5 8.62 3.6 0
79 14.5 3.5 3.6 0
80 12.12 7.62 7.2 0
81 12.12 14.97 7.2 0
84 12.12 11.3 8.4 0
85 12.12 11.3 7.2 0
86 12.12 11.8 7.2 0
88 12.12 11.8 8.237 0
89 12.12 12.3 7.2 0
91 12.12 12.3 8.073 0
92 12.12 12.8 7.2 0
94 12.12 12.8 7.91 0
95 12.12 13.3 7.2 0
97 12.12 13.3 7.747 0
98 12.12 13.8 7.2 0
100 12.12 13.8 7.584 0
101 12.12 14.3 7.2 0
103 12.12 14.3 7.42 0
104 12.12 10.8 7.2 0
106 12.12 10.8 8.237 0
107 12.12 10.3 7.2 0
109 12.12 10.3 8.073 0
110 12.12 9.795 7.2 0
112 12.12 9.795 7.91 0
113 12.12 9.295 7.2 0
115 12.12 9.295 7.747 0
116 12.12 8.795 7.2 0
118 12.12 8.795 7.584 0
119 12.12 8.295 7.2 0
121 12.12 8.295 7.42 0
122 16.87 14.3 7.2 0
123 16.87 14.97 7.2 0
124 16.87 14.3 7.42 0
125 16.87 7.62 7.2 0
126 16.87 8.295 7.42 0
127 16.87 11.3 7.2 0
128 16.87 11.3 8.4 0
129 16.87 11.8 7.2 0
130 16.87 11.8 8.237 0
131 16.87 12.3 7.2 0
132 16.87 12.3 8.073 0
133 16.87 12.8 7.2 0
134 16.87 12.8 7.91 0
135 16.87 13.3 7.2 0
136 16.87 13.3 7.747 0
137 16.87 13.8 7.2 0
138 16.87 13.8 7.584 0
139 16.87 10.8 7.2 0
140 16.87 10.8 8.237 0
141 16.87 10.3 7.2 0
142 16.87 10.3 8.073 0
143 16.87 9.795 7.2 0
144 16.87 9.795 7.91 0
145 16.87 9.295 7.2 0
146 16.87 9.295 7.747 0
147 16.87 8.795 7.2 0
148 16.87 8.795 7.584 0
149 16.87 8.295 7.2 0
150 7.372 14.3 7.2 0
151 7.372 14.97 7.2 0
152 7.372 14.3 7.42 0
153 7.372 7.62 7.2 0
154 7.372 8.295 7.42 0
155 7.372 11.3 7.2 0
156 7.372 11.3 8.4 0
157 7.372 11.8 7.2 0
158 7.372 11.8 8.237 0
159 7.372 12.3 7.2 0
160 7.372 12.3 8.073 0
161 7.372 12.8 7.2 0
162 7.372 12.8 7.91 0
163 7.372 13.3 7.2 0
164 7.372 13.3 7.747 0
165 7.372 13.8 7.2 0
166 7.372 13.8 7.584 0
167 7.372 10.8 7.2 0
168 7.372 10.8 8.237 0
169 7.372 10.3 7.2 0
170 7.372 10.3 8.073 0
171 7.372 9.795 7.2 0
172 7.372 9.795 7.91 0
173 7.372 9.295 7.2 0
174 7.372 9.295 7.747 0
175 7.372 8.795 7.2 0
176 7.372 8.795 7.584 0
177 7.372 8.295 7.2 0
178 2.622 14.3 7.2 0
179 2.622 14.97 7.2 0
180 2.622 14.3 7.42 0
181 2.622 7.62 7.2 0
182 2.622 8.295 7.42 0
183 2.622 11.3 7.2 0
184 2.622 11.3 8.4 0
185 2.622 11.8 7.2 0
186 2.622 11.8 8.237 0
187 2.622 12.3 7.2 0
188 2.622 12.3 8.073 0
189 2.622 12.8 7.2 0
190 2.622 12.8 7.91 0
191 2.622 13.3 7.2 0
192 2.622 13.3 7.747 0
193 2.622 13.8 7.2 0
194 2.622 13.8 7.584 0
195 2.622 10.8 7.2 0
196 2.622 10.8 8.237 0
197 2.622 10.3 7.2 0
198 2.622 10.3 8.073 0
199 2.622 9.795 7.2 0
200 2.622 9.795 7.91 0
201 2.622 9.295 7.2 0
202 2.622 9.295 7.747 0
203 2.622 8.795 7.2 0
204 2.622 8.795 7.584 0
205 2.622 8.295 7.2 0
206 0 14.3 7.2 0
207 0 14.97 7.2 0
208 0 14.3 7.42 0
209 0 7.62 7.2 0
210 0 8.295 7.42 0
211 0 11.3 7.2 0
212 0 11.3 8.4 0
213 0 11.8 7.2 0
214 0 11.8 8.237 0
215 0 12.3 7.2 0
216 0 12.3 8.073 0
217 0 12.8 7.2 0
218 0 12.8 7.91 0
219 0 13.3 7.2 0
220 0 13.3 7.747 0
221 0 13.8 7.2 0
222 0 13.8 7.584 0
223 0 10.8 7.2 0
224 0 10.8 8.237 0
225 0 10.3 7.2 0
226 0 10.3 8.073 0
227 0 9.795 7.2 0
228 0 9.795 7.91 0
229 0 9.295 7.2 0
230 0 9.295 7.747 0
231 0 8.795 7.2 0
232 0 8.795 7.584 0
233 0 8.295 7.2 0
234 0 5.32 3.6 0
235 2.622 5.32 3.6 0
257 0 0 -4.2 0
258 16.87 0 -4.2 0
259 0 3.5 -4.2 0
260 2.622 3.5 -4.2 0
261 7.372 3.5 -4.2 0
262 12.12 3.5 -4.2 0
263 16.87 3.5 -4.2 0
264 0 8.62 -4.2 0
265 2.622 8.62 -4.2 0
266 7.372 8.62 -4.2 0
267 12.12 8.62 -4.2 0
268 16.87 8.62 -4.2 0
269 0 13.97 -4.2 0
270 2.622 13.97 -4.2 0
271 7.372 13.97 -4.2 0
272 12.12 13.97 -4.2 0
273 16.87 13.97 -4.2 0
274 12.12 1.25 0 0
275 14.62 0 0 0
276 14.62 1.25 0 0
277 16.87 2.5 3.6 0
278 12.12 2.5 3.6 0
279 13.12 0 3.6 0
280 13.12 2.5 3.6 0
281 12.12 6.06 0 0
< Boundary >
** SUPPORT / SPECIFIED DISPLACEMENT
NODE SUPPORT SPECIFIED DISPLACEMENT
DDDRRR Dx Dy Dz Rx Ry Rz
-------- -------- ---------- ---------- ---------- ---------- ---------- ----------
257 111111 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
258 111111 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
259 111111 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
260 111111 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
261 111111 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
262 111111 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
263 111111 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
264 111111 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
265 111111 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
266 111111 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
267 111111 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
268 111111 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
269 111111 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
270 111111 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
271 111111 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
272 111111 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
273 111111 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
< Floor Diaphragm/Rigid Link >
*** FLOOR DIAPHRAGM / RIGID LINK DATA
MASTER DDDRRR NODES OF SAME DISPLACEMENT
---------- --------------- ------------------------------------------------------------
3F Floor Diaphragm 21to40 72to79 234 235 277to280
2F Floor Diaphragm 1to20 274to276 281
< Beam >
*** BEAM MEMBER DATA
NO NODAL CONNECTIVITY BEAM END RELEASE MATERIAL SECTION LENGTH
I J I J
-------- --------- -------- -------- -------- --------------- --------------- ----------
1 16 17 - - Grade C3000 B3 2.622
2 17 18 - - Grade C3000 B3 4.75
3 18 19 - - Grade C3000 B3 4.75
4 19 20 - - Grade C3000 B3 4.75
5 11 12 - - Grade C3000 B2 2.622
6 12 13 - - Grade C3000 B2 4.75
7 13 14 - - Grade C3000 B2 4.75
8 14 15 - - Grade C3000 B2 4.75
9 6 7 - - Grade C3000 B2 2.622
10 7 8 - - Grade C3000 B2 4.75
11 8 9 - - Grade C3000 B2 4.75
12 9 10 - - Grade C3000 B2 4.75
13 1 2 - - Grade C3000 BEAM COVER 2.622
14 2 3 - - Grade C3000 BEAM COVER 4.75
15 3 4 - - Grade C3000 BEAM COVER 4.75
16 4 275 - - Grade C3000 BEAM COVER 2.5
17 1 6 - - Grade C3000 B3 3.5
18 6 11 - - Grade C3000 B3 5.12
19 11 16 - - Grade C3000 B3 5.35
20 7 2 000000 000011 Grade C3000 B3 3.5
21 7 12 - - Grade C3000 B1 5.12
22 12 17 - - Grade C3000 B1 5.35
23 8 3 000000 000011 Grade C3000 2FCB 3.5
24 8 13 - - Grade C3000 B1 5.12
25 13 18 - - Grade C3000 B1 5.35
26 9 274 - - Grade C3000 B3 2.25
27 9 14 - - Grade C3000 B1 5.12
28 14 19 - - Grade C3000 B1 5.35
29 5 10 - - Grade C3000 B3 3.5
30 10 15 - - Grade C3000 B3 5.12
31 15 20 - - Grade C3000 B3 5.35
32 36 37 - - Grade C3000 3B3 2.622
33 37 38 - - Grade C3000 3B3 4.75
34 38 39 - - Grade C3000 3B3 4.75
35 39 40 - - Grade C3000 3B3 4.75
36 31 32 - - Grade C3000 3B2 2.622
37 32 33 - - Grade C3000 3B2 4.75
38 33 34 - - Grade C3000 3B2 4.75
39 34 78 - - Grade C3000 3B2 2.375
40 26 27 - - Grade C3000 3B2 2.622
41 27 28 - - Grade C3000 3B2 4.75
42 28 29 - - Grade C3000 3B2 4.75
43 29 79 - - Grade C3000 3B2 2.375
44 21 22 - - Grade C3000 3B3 2.622
45 22 23 - - Grade C3000 3B3 4.75
46 23 24 - - Grade C3000 3B3 4.75
47 24 279 - - Grade C3000 3B3 1
48 21 26 - - Grade C3000 3B2 3.5
49 26 234 - - Grade C3000 3B2 1.82
50 31 36 - - Grade C3000 3B2 5.35
51 27 22 - - Grade C3000 3B2 3.5
52 27 235 - - Grade C3000 3B1 1.82
53 32 37 - - Grade C3000 3B1 5.35
54 28 23 - - Grade C3000 3FCRITICALBEAM 3.5
55 28 33 - - Grade C3000 3B1 5.12
56 33 38 - - Grade C3000 3B1 5.35
57 29 278 - - Grade C3000 3B2 1
58 29 72 - - Grade C3000 3B1 1.707
59 34 39 - - Grade C3000 3B1 5.35
60 25 277 - - Grade C3000 3B2 2.5
61 30 74 - - Grade C3000 3B2 1.707
62 35 40 - - Grade C3000 3B2 5.35
63 16 36 - - Grade C3000 2C1 3.6
64 17 37 - - Grade C3000 CANTI/COL 3.6
65 18 38 - - Grade C3000 CANTI/COL 3.6
66 19 39 - - Grade C3000 CANTI/COL 3.6
67 20 40 - - Grade C3000 2C1 3.6
68 11 31 - - Grade C3000 2C1 3.6
69 12 32 - - Grade C3000 2C1 3.6
70 13 33 - - Grade C3000 2C1 3.6
71 14 34 - - Grade C3000 2C1 3.6
72 15 35 - - Grade C3000 2C1 3.6
73 6 26 - - Grade C3000 2C1 3.6
74 7 27 - - Grade C3000 CANTI/COL 3.6
75 8 28 - - Grade C3000 CANTI/COL 3.6
76 9 29 - - Grade C3000 CANTI/COL 3.6
77 10 30 - - Grade C3000 2C1 3.6
78 1 21 - - Grade C3000 C1 3.6
82 5 25 - - Grade C3000 C1 3.6
100 67 68 - - Grade C3000 3B3 2.622
101 68 69 - - Grade C3000 3B3 4.75
102 69 70 - - Grade C3000 3B3 4.75
103 70 71 - - Grade C3000 3B3 4.75
104 62 63 - - Grade C3000 3B3 2.622
105 63 64 - - Grade C3000 3B3 4.75
106 64 65 - - Grade C3000 3B3 4.75
107 65 66 - - Grade C3000 3B3 4.75
108 60 61 - - Grade C3000 3B3 4.75
109 58 59 - - Grade C3000 3B3 4.75
113 58 60 - - Grade C3000 3B3 3.5
116 59 61 - - Grade C3000 3B3 3.5
120 25 59 - - Grade C3000 2C2/3C1 3.6
121 29 60 - - Grade C3000 3C1 3.6
122 30 61 - - Grade C3000 3C1 3.6
123 31 62 - - Grade C3000 3C1 3.6
124 32 63 - - Grade C3000 3C1 3.6
125 33 64 - - Grade C3000 3C1 3.6
126 34 65 - - Grade C3000 3C1 3.6
127 35 66 - - Grade C3000 3C1 3.6
128 36 67 - - Grade C3000 3C1 3.6
129 37 68 - - Grade C3000 3C1 3.6
130 38 69 - - Grade C3000 3C1 3.6
131 39 70 - - Grade C3000 3C1 3.6
132 40 71 - - Grade C3000 3C1 3.6
133 62 231 - - Grade C3000 3B3 0.175
134 63 203 - - Grade C3000 3B3 0.175
135 64 175 - - Grade C3000 3B3 0.175
136 65 116 - - Grade C3000 3B3 0.175
137 66 147 - - Grade C3000 3B3 0.175
138 60 80 - - Grade C3000 3B3 4.12
139 61 125 - - Grade C3000 3B3 4.12
140 72 73 - - Grade C3000 3B1 1.707
141 73 34 - - Grade C3000 3B1 1.707
142 74 75 - - Grade C3000 3B2 1.707
143 75 35 - - Grade C3000 3B2 1.707
144 73 76 - - Grade C3000 3B3 2.375
145 72 77 - - Grade C3000 3B3 2.375
146 76 75 - - Grade C3000 3B3 2.375
147 77 74 - - Grade C3000 3B3 2.375
148 78 35 - - Grade C3000 3B2 2.375
149 79 30 - - Grade C3000 3B2 2.375
150 79 77 - - DUMMY DUMMY BEAM 1.707
151 77 76 - - DUMMY DUMMY BEAM 1.707
152 76 78 - - DUMMY DUMMY BEAM 1.707
153 80 119 - - Grade C3000 3B3 0.675
157 70 101 - - A36 TOP AND BOTTOM~ 0.325
159 81 103 - - A36 TOP AND BOTTOM~ 0.7101
160 80 121 - - A36 TOP AND BOTTOM~ 0.7101
161 85 86 - - Grade C3000 3B3 0.5
162 85 84 - - A36 WEB 1.2
163 86 88 - - A36 WEB 1.037
165 86 89 - - Grade C3000 3B3 0.5
166 88 84 - - A36 TOP AND BOTTOM~ 0.526
167 89 91 - - A36 WEB 0.8735
169 89 92 - - Grade C3000 3B3 0.5
170 91 88 - - A36 TOP AND BOTTOM~ 0.526
171 92 94 - - A36 WEB 0.7102
173 92 95 - - Grade C3000 3B3 0.5
174 94 91 - - A36 TOP AND BOTTOM~ 0.526
175 95 97 - - A36 WEB 0.5469
177 95 98 - - Grade C3000 3B3 0.5
178 97 94 - - A36 TOP AND BOTTOM~ 0.526
179 98 100 - - A36 WEB 0.3837
181 98 70 - - Grade C3000 3B3 0.175
182 100 97 - - A36 TOP AND BOTTOM~ 0.526
183 101 103 - - A36 WEB 0.2204
185 101 81 - - A36 TOP AND BOTTOM~ 0.675
186 103 100 - - A36 TOP AND BOTTOM~ 0.526
187 104 106 - - A36 WEB 1.037
189 104 85 - - Grade C3000 3B3 0.5
190 106 84 - - A36 TOP AND BOTTOM~ 0.526
191 107 109 - - A36 WEB 0.8735
193 107 104 - - Grade C3000 3B3 0.5
194 109 106 - - A36 TOP AND BOTTOM~ 0.526
195 110 112 - - A36 WEB 0.7102
197 110 107 - - Grade C3000 3B3 0.5
198 112 109 - - A36 TOP AND BOTTOM~ 0.526
199 113 115 - - A36 WEB 0.5469
201 113 110 - - Grade C3000 3B3 0.5
202 115 112 - - A36 TOP AND BOTTOM~ 0.526
203 116 118 - - A36 WEB 0.3837
205 116 113 - - Grade C3000 3B3 0.5
206 118 115 - - A36 TOP AND BOTTOM~ 0.526
207 119 121 - - A36 WEB 0.2204
209 119 65 - - Grade C3000 3B3 0.325
210 121 118 - - A36 TOP AND BOTTOM~ 0.526
211 85 88 - - A36 WEB 1.151
212 86 91 - - A36 WEB 1.006
213 89 94 - - A36 WEB 0.8686
214 92 97 - - A36 WEB 0.741
215 95 100 - - A36 WEB 0.6302
216 98 103 - - A36 WEB 0.5464
217 85 106 - - A36 WEB 1.151
218 104 109 - - A36 WEB 1.006
219 107 112 - - A36 WEB 0.8686
220 110 115 - - A36 WEB 0.741
221 113 118 - - A36 WEB 0.6302
222 116 121 - - A36 WEB 0.5464
223 71 122 - - A36 TOP AND BOTTOM~ 0.325
224 123 124 - - A36 TOP AND BOTTOM~ 0.7101
225 125 126 - - A36 TOP AND BOTTOM~ 0.7101
226 125 149 - - Grade C3000 3B3 0.675
227 127 128 - - A36 WEB 1.2
228 127 129 - - Grade C3000 3B3 0.5
229 129 130 - - A36 WEB 1.037
230 129 131 - - Grade C3000 3B3 0.5
231 130 128 - - A36 TOP AND BOTTOM~ 0.526
232 131 132 - - A36 WEB 0.8735
233 131 133 - - Grade C3000 3B3 0.5
234 132 130 - - A36 TOP AND BOTTOM~ 0.526
235 133 134 - - A36 WEB 0.7102
236 133 135 - - Grade C3000 3B3 0.5
237 134 132 - - A36 TOP AND BOTTOM~ 0.526
238 135 136 - - A36 WEB 0.5469
239 135 137 - - Grade C3000 3B3 0.5
240 136 134 - - A36 TOP AND BOTTOM~ 0.526
241 137 138 - - A36 WEB 0.3837
242 137 71 - - Grade C3000 3B3 0.175
243 138 136 - - A36 TOP AND BOTTOM~ 0.526
244 122 124 - - A36 WEB 0.2204
245 122 123 - - A36 TOP AND BOTTOM~ 0.675
246 124 138 - - A36 TOP AND BOTTOM~ 0.526
247 139 140 - - A36 WEB 1.037
248 139 127 - - Grade C3000 3B3 0.5
249 140 128 - - A36 TOP AND BOTTOM~ 0.526
250 141 142 - - A36 WEB 0.8735
251 141 139 - - Grade C3000 3B3 0.5
252 142 140 - - A36 TOP AND BOTTOM~ 0.526
253 143 144 - - A36 WEB 0.7102
254 143 141 - - Grade C3000 3B3 0.5
255 144 142 - - A36 TOP AND BOTTOM~ 0.526
256 145 146 - - A36 WEB 0.5469
257 145 143 - - Grade C3000 3B3 0.5
258 146 144 - - A36 TOP AND BOTTOM~ 0.526
259 147 148 - - A36 WEB 0.3837
260 147 145 - - Grade C3000 3B3 0.5
261 148 146 - - A36 TOP AND BOTTOM~ 0.526
262 149 126 - - A36 WEB 0.2204
263 149 66 - - Grade C3000 3B3 0.325
264 126 148 - - A36 TOP AND BOTTOM~ 0.526
265 127 130 - - A36 WEB 1.151
266 129 132 - - A36 WEB 1.006
267 131 134 - - A36 WEB 0.8686
268 133 136 - - A36 WEB 0.741
269 135 138 - - A36 WEB 0.6302
270 137 124 - - A36 WEB 0.5464
271 127 140 - - A36 WEB 1.151
272 139 142 - - A36 WEB 1.006
273 141 144 - - A36 WEB 0.8686
274 143 146 - - A36 WEB 0.741
275 145 148 - - A36 WEB 0.6302
276 147 126 - - A36 WEB 0.5464
277 69 150 - - A36 TOP AND BOTTOM~ 0.325
278 151 152 - - A36 TOP AND BOTTOM~ 0.7101
279 153 154 - - A36 TOP AND BOTTOM~ 0.7101
280 155 156 - - A36 WEB 1.2
281 155 157 - - Grade C3000 3B3 0.5
282 157 158 - - A36 WEB 1.037
283 157 159 - - Grade C3000 3B3 0.5
284 158 156 - - A36 TOP AND BOTTOM~ 0.526
285 159 160 - - A36 WEB 0.8735
286 159 161 - - Grade C3000 3B3 0.5
287 160 158 - - A36 TOP AND BOTTOM~ 0.526
288 161 162 - - A36 WEB 0.7102
289 161 163 - - Grade C3000 3B3 0.5
290 162 160 - - A36 TOP AND BOTTOM~ 0.526
291 163 164 - - A36 WEB 0.5469
292 163 165 - - Grade C3000 3B3 0.5
293 164 162 - - A36 TOP AND BOTTOM~ 0.526
294 165 166 - - A36 WEB 0.3837
295 165 69 - - Grade C3000 3B3 0.175
296 166 164 - - A36 TOP AND BOTTOM~ 0.526
297 150 152 - - A36 WEB 0.2204
298 150 151 - - A36 TOP AND BOTTOM~ 0.675
299 152 166 - - A36 TOP AND BOTTOM~ 0.526
300 167 168 - - A36 WEB 1.037
301 167 155 - - Grade C3000 3B3 0.5
302 168 156 - - A36 TOP AND BOTTOM~ 0.526
303 169 170 - - A36 WEB 0.8735
304 169 167 - - Grade C3000 3B3 0.5
305 170 168 - - A36 TOP AND BOTTOM~ 0.526
306 171 172 - - A36 WEB 0.7102
307 171 169 - - Grade C3000 3B3 0.5
308 172 170 - - A36 TOP AND BOTTOM~ 0.526
309 173 174 - - A36 WEB 0.5469
310 173 171 - - Grade C3000 3B3 0.5
311 174 172 - - A36 TOP AND BOTTOM~ 0.526
312 175 176 - - A36 WEB 0.3837
313 175 173 - - Grade C3000 3B3 0.5
314 176 174 - - A36 TOP AND BOTTOM~ 0.526
315 177 154 - - A36 WEB 0.2204
316 154 176 - - A36 TOP AND BOTTOM~ 0.526
317 155 158 - - A36 WEB 1.151
318 157 160 - - A36 WEB 1.006
319 159 162 - - A36 WEB 0.8686
320 161 164 - - A36 WEB 0.741
321 163 166 - - A36 WEB 0.6302
322 165 152 - - A36 WEB 0.5464
323 155 168 - - A36 WEB 1.151
324 167 170 - - A36 WEB 1.006
325 169 172 - - A36 WEB 0.8686
326 171 174 - - A36 WEB 0.741
327 173 176 - - A36 WEB 0.6302
328 175 154 - - A36 WEB 0.5464
329 68 178 - - A36 TOP AND BOTTOM~ 0.325
330 179 180 - - A36 TOP AND BOTTOM~ 0.7101
331 181 182 - - A36 TOP AND BOTTOM~ 0.7101
332 183 184 - - A36 WEB 1.2
333 183 185 - - Grade C3000 3B3 0.5
334 185 186 - - A36 WEB 1.037
335 185 187 - - Grade C3000 3B3 0.5
336 186 184 - - A36 TOP AND BOTTOM~ 0.526
337 187 188 - - A36 WEB 0.8735
338 187 189 - - Grade C3000 3B3 0.5
339 188 186 - - A36 TOP AND BOTTOM~ 0.526
340 189 190 - - A36 WEB 0.7102
341 189 191 - - Grade C3000 3B3 0.5
342 190 188 - - A36 TOP AND BOTTOM~ 0.526
343 191 192 - - A36 WEB 0.5469
344 191 193 - - Grade C3000 3B3 0.5
345 192 190 - - A36 TOP AND BOTTOM~ 0.526
346 193 194 - - A36 WEB 0.3837
347 193 68 - - Grade C3000 3B3 0.175
348 194 192 - - A36 TOP AND BOTTOM~ 0.526
349 178 180 - - A36 WEB 0.2204
350 178 179 - - A36 TOP AND BOTTOM~ 0.675
351 180 194 - - A36 TOP AND BOTTOM~ 0.526
352 195 196 - - A36 WEB 1.037
353 195 183 - - Grade C3000 3B3 0.5
354 196 184 - - A36 TOP AND BOTTOM~ 0.526
355 197 198 - - A36 WEB 0.8735
356 197 195 - - Grade C3000 3B3 0.5
357 198 196 - - A36 TOP AND BOTTOM~ 0.526
358 199 200 - - A36 WEB 0.7102
359 199 197 - - Grade C3000 3B3 0.5
360 200 198 - - A36 TOP AND BOTTOM~ 0.526
361 201 202 - - A36 WEB 0.5469
362 201 199 - - Grade C3000 3B3 0.5
363 202 200 - - A36 TOP AND BOTTOM~ 0.526
364 203 204 - - A36 WEB 0.3837
365 203 201 - - Grade C3000 3B3 0.5
366 204 202 - - A36 TOP AND BOTTOM~ 0.526
367 205 182 - - A36 WEB 0.2204
368 182 204 - - A36 TOP AND BOTTOM~ 0.526
369 183 186 - - A36 WEB 1.151
370 185 188 - - A36 WEB 1.006
371 187 190 - - A36 WEB 0.8686
372 189 192 - - A36 WEB 0.741
373 191 194 - - A36 WEB 0.6302
374 193 180 - - A36 WEB 0.5464
375 183 196 - - A36 WEB 1.151
376 195 198 - - A36 WEB 1.006
377 197 200 - - A36 WEB 0.8686
378 199 202 - - A36 WEB 0.741
379 201 204 - - A36 WEB 0.6302
380 203 182 - - A36 WEB 0.5464
381 67 206 - - A36 TOP AND BOTTOM~ 0.325
382 207 208 - - A36 TOP AND BOTTOM~ 0.7101
383 209 210 - - A36 TOP AND BOTTOM~ 0.7101
384 211 212 - - A36 WEB 1.2
385 211 213 - - Grade C3000 3B3 0.5
386 213 214 - - A36 WEB 1.037
387 213 215 - - Grade C3000 3B3 0.5
388 214 212 - - A36 TOP AND BOTTOM~ 0.526
389 215 216 - - A36 WEB 0.8735
390 215 217 - - Grade C3000 3B3 0.5
391 216 214 - - A36 TOP AND BOTTOM~ 0.526
392 217 218 - - A36 WEB 0.7102
393 217 219 - - Grade C3000 3B3 0.5
394 218 216 - - A36 TOP AND BOTTOM~ 0.526
395 219 220 - - A36 WEB 0.5469
396 219 221 - - Grade C3000 3B3 0.5
397 220 218 - - A36 TOP AND BOTTOM~ 0.526
398 221 222 - - A36 WEB 0.3837
399 221 67 - - Grade C3000 3B3 0.175
400 222 220 - - A36 TOP AND BOTTOM~ 0.526
401 206 208 - - A36 WEB 0.2204
402 206 207 - - A36 TOP AND BOTTOM~ 0.675
403 208 222 - - A36 TOP AND BOTTOM~ 0.526
404 223 224 - - A36 WEB 1.037
405 223 211 - - Grade C3000 3B3 0.5
406 224 212 - - A36 TOP AND BOTTOM~ 0.526
407 225 226 - - A36 WEB 0.8735
408 225 223 - - Grade C3000 3B3 0.5
409 226 224 - - A36 TOP AND BOTTOM~ 0.526
410 227 228 - - A36 WEB 0.7102
411 227 225 - - Grade C3000 3B3 0.5
412 228 226 - - A36 TOP AND BOTTOM~ 0.526
413 229 230 - - A36 WEB 0.5469
414 229 227 - - Grade C3000 3B3 0.5
415 230 228 - - A36 TOP AND BOTTOM~ 0.526
416 231 232 - - A36 WEB 0.3837
417 231 229 - - Grade C3000 3B3 0.5
418 232 230 - - A36 TOP AND BOTTOM~ 0.526
419 233 210 - - A36 WEB 0.2204
420 210 232 - - A36 TOP AND BOTTOM~ 0.526
421 211 214 - - A36 WEB 1.151
422 213 216 - - A36 WEB 1.006
423 215 218 - - A36 WEB 0.8686
424 217 220 - - A36 WEB 0.741
425 219 222 - - A36 WEB 0.6302
426 221 208 - - A36 WEB 0.5464
427 211 224 - - A36 WEB 1.151
428 223 226 - - A36 WEB 1.006
429 225 228 - - A36 WEB 0.8686
430 227 230 - - A36 WEB 0.741
431 229 232 - - A36 WEB 0.6302
432 231 210 - - A36 WEB 0.5464
433 62 233 - - A36 TOP AND BOTTOM~ 0.325
434 233 209 - - A36 TOP AND BOTTOM~ 0.675
435 63 205 - - A36 TOP AND BOTTOM~ 0.325
436 205 181 - - A36 TOP AND BOTTOM~ 0.675
437 64 177 - - A36 TOP AND BOTTOM~ 0.325
438 177 153 - - A36 TOP AND BOTTOM~ 0.675
439 234 31 - - Grade C3000 3B2 3.3
440 235 32 - - Grade C3000 3B1 3.3
441 234 235 - - DUMMY DUMMY BEAM 2.622
463 257 1 - - Grade C3000 C1 4.2
464 258 5 - - Grade C3000 C1 4.2
465 259 6 - - Grade C3000 C1 4.2
466 260 7 - - Grade C3000 CANTI/COL 4.2
467 261 8 - - Grade C3000 CANTI/COL 4.2
468 262 9 - - Grade C3000 CANTI/COL 4.2
469 263 10 - - Grade C3000 C1 4.2
470 264 11 - - Grade C3000 C1 4.2
471 265 12 - - Grade C3000 C1 4.2
472 266 13 - - Grade C3000 CANTI/COL 4.2
473 267 14 - - Grade C3000 C1 4.2
474 268 15 - - Grade C3000 C1 4.2
475 269 16 - - Grade C3000 C1 4.2
476 270 17 - - Grade C3000 CANTI/COL 4.2
477 271 18 - - Grade C3000 CANTI/COL 4.2
478 272 19 - - Grade C3000 CANTI/COL 4.2
479 273 20 - - Grade C3000 C1 4.2
480 274 4 000000 000011 Grade C3000 B3 1.25
481 275 5 - - Grade C3000 BEAM COVER 2.25
482 274 276 - - DUMMY DUMMY BEAM 2.5
483 275 276 - - DUMMY DUMMY BEAM 1.25
484 277 30 - - Grade C3000 3B2 1
485 278 24 - - Grade C3000 3B2 2.5
486 279 25 - - Grade C3000 3B3 3.75
487 279 280 - - DUMMY DUMMY BEAM 2.5
488 280 277 - - DUMMY DUMMY BEAM 3.75
489 278 280 - - DUMMY DUMMY BEAM 1
< Seismic Load >
[ LOAD CASE : EX+ ]
CODE = UBC.1997
-------------------------------------------------------------------------------------------------
-----
* MASS GENERATION DATA FOR LATERAL ANALYSIS OF BUILDING [UNIT: kN, m]
_________________________________________________________
STORY TRANSLATIONAL MASS ROTATIONAL CENTER OF MASS
NAME (X-DIR) (Y-DIR) MASS (X-COORD) (Y-COORD)
----------- ----------- ----------- ----------- ----------- -----------
Roof 0.0 0.0 0.0 0.0 0.0
10F 0.0 0.0 0.0 0.0 0.0
9F 0.0 0.0 0.0 0.0 0.0
8F 0.0 0.0 0.0 0.0 0.0
7F 0.0 0.0 0.0 0.0 0.0
6F 0.0 0.0 0.0 0.0 0.0
5F 0.0 0.0 0.0 0.0 0.0
4F 0.0 0.0 0.0 0.0 0.0
3F 229.124841 229.124841 12559.3962 8.54526098 7.90226119
2F 262.125665 262.125665 14423.2849 8.10800711 7.33476108
1F 0.0 0.0 0.0 0.0 0.0
----------- ----------- ----------- ----------- ----------- -----------
TOTAL : 491.250506 491.250506
* ADDITIONAL MASSES FOR THE CALCULATION OF EQUIVALENT SEISMIC FORCE
_____________________________________________________________________
Note. The following masses are between two adjacent stories or on the
nodes released from floor rigid diaphragm by *Diaphragm Disconnect command.
The masses are proportionally distributed to upper/lower stories according
to their vertical locations. For dynamic analysis, however, floor masses
and masses on vertical elements remain at their original locations.
STORY TRANSLATIONAL MASS
NAME (X-DIR) (Y-DIR)
-------------- ----------- -----------
Roof 0.65869628 0.65869628
10F 1.33255034 1.33255034
9F 1.32782658 1.32782658
8F 1.32320497 1.32320497
7F 1.3187427 1.3187427
6F 1.31453694 1.31453694
5F 1.5380663 1.5380663
4F 45.0550083 45.0550083
3F 0.0 0.0
2F 0.0 0.0
1F 15.1006099 15.1006099
-------------- ----------- -----------
TOTAL : 68.9692423 68.9692423
* EQUIVALENT SEISMIC LOAD IN ACCORDANCE WITH UNIFORM BUILDING CODE 1997 [UNIT: kN, m]
_____________________________________________________________________________________________
Seismic Zone Factor (Z) : 0.40
Importance Factor (I) : 1.00
Soil Profile Type : SD
Seismic Source Type : A
Closest Distance To Known Seismic Source [km] : 18.70
Near Source Factor, Na (UBC-97 Table 16-S) : 1.00
Near Source Factor, Nv (UBC-97 Table 16-T) : 1.00
Seismic Coefficient, Ca (UBC-97 Table 16-Q) : 0.44
Seismic Coefficient, Cv (UBC-97 Table 16-R) : 0.64
Fundamental Period Associated With X-dir. (Tx) : 0.4537
R Factor of Lateral System for X-direction (Rx) : 8.5000
Seismic Coefficient for X-dir. UBC-97(Para.1630.2.1) : 0.129412
Fundamental Period Associated With Y-dir. (Ty) : 0.4537
R Factor of Lateral System for Y-direction (Ry) : 8.5000
Seismic Coefficient for Y-dir. UBC-97(Para.1630.2.1) : 0.129412
Total Effective Weight For X-dir. Seismic Loads (Wx) : 5345.438268
Total Effective Weight For Y-dir. Seismic Loads (Wy) : 5345.438268
Scale Factor For X-directional Seismic Loads : 1.00
Scale Factor For Y-directional Seismic Loads : 0.00
Accidental Eccentricity For X-direction (Ex) : None
Accidental Eccentricity For Y-direction (Ey) : None
Torsional Amplification for Accidental Eccentricity : Do not Consider
Torsional Amplification for Inherent Eccentricity : Do not Consider
Total Base Shear Of Model For X-direction : 691.762599
Total Base Shear Of Model For Y-direction : 0.000000
Summation Of Wi*Hi Of Model For X-direction : 34399.841088
Summation Of Wi*Hi Of Model For Y-direction : 0.000000
--------------------------------------------------------------------------------------
===========================
ECCENTRICITY RELATED DATA
===========================
X - D I R E C T I O N A L L O A D Y - D I R E C T I O N A L L O A
D
STORY ACCIDENTAL INHERENT ACCIDENTAL INHERENT ACCIDENTAL INHERENT ACCIDENTAL
INHERENT
NAME ECCENT. ECCENT. [Link] [Link] ECCENT. ECCENT. [Link]
[Link]
---------- ---------- ---------- ---------- ---------- ---------- ---------- ---------- ----
------
Roof 0.0 0.0 1.0 0.0 0.0 0.0 1.0
0.0
10F 0.0 0.0 1.0 0.0 0.0 0.0 1.0
0.0
9F 0.0 0.0 1.0 0.0 0.0 0.0 1.0
0.0
8F 0.0 0.0 1.0 0.0 0.0 0.0 1.0
0.0
7F 0.0 0.0 1.0 0.0 0.0 0.0 1.0
0.0
6F 0.0 0.0 1.0 0.0 0.0 0.0 1.0
0.0
5F 0.0 0.0 1.0 0.0 0.0 0.0 1.0
0.0
4F 0.0 0.0 1.0 0.0 0.0 0.0 1.0
0.0
3F 0.0 0.0 1.0 0.0 0.0 0.0 1.0
0.0
2F 0.0 0.0 1.0 0.0 0.0 0.0 1.0
0.0
G.L 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0
-------------------------------------------------------------------------------------------------
------
-------------------------------------------------------------------------------------------------
------
The accidental amplification factors are automatically set to 1.0 when torsional amplification
effect
to accidental eccentricity is not considered.
The inherent amplification factors are automatically set to 0 when torsional amplification effect
to inherent eccentricity is not considered.
The inherent amplification factors are all set to 'the input value - 1.0'.(This is to exclude the
true
inherent torsion)
-------------------------------------------------------------------------------------------------
------
** Story Force , Seismic Force x Scale Factor + Added Force
S E I S M I C L O A D G E N E R A T I O N D A T A X - D I R E C T I O N
STORY STORY STORY SEISMIC ADDED STORY STORY OVERTURN. ACCIDENT. INHERENT
TOTAL
NAME WEIGHT LEVEL FORCE FORCE FORCE SHEAR MOMENT TORSION TORSION
TORSION
---------- -------- ------- -------- -------- -------- -------- --------- --------- --------- ---
------
Roof 6.459176 12.6 1.636622 0.0 1.636622 0.0 0.0 0.0 0.0
0.0
10F 13.06699 12.4367 3.268004 0.0 3.268004 1.636622 0.267204 0.0 0.0
0.0
9F 13.02067 12.2735 3.21367 0.0 3.21367 4.904625 1.067959 0.0 0.0
0.0
8F 12.97535 12.1102 3.159884 0.0 3.159884 8.118295 2.393395 0.0 0.0
0.0
7F 12.93159 11.9469 3.106771 0.0 3.106771 11.27818 4.23473 0.0 0.0
0.0
6F 12.89035 11.7837 3.054541 0.0 3.054541 14.38495 6.583293 0.0 0.0
0.0
5F 15.08228 11.6204 3.524431 0.0 3.524431 17.43949 9.430557 0.0 0.0
0.0
4F 441.8094 11.4 101.2839 0.0 101.2839 20.96392 14.05118 0.0 0.0
0.0
3F 2246.798 7.8 352.419 0.0 352.419 122.2478 454.1434 0.0 0.0
0.0
2F 2570.404 4.2 217.0958 0.0 217.0958 474.6668 2162.944 0.0 0.0
0.0
G.L. -- 0.0 -- -- -- 691.7626 5068.347 --- ---
---
-------------------------------------------------------------------------------------------------
------
S E I S M I C L O A D G E N E R A T I O N D A T A Y - D I R E C T I O N
STORY STORY STORY SEISMIC ADDED STORY STORY OVERTURN. ACCIDENT. INHERENT
TOTAL
NAME WEIGHT LEVEL FORCE FORCE FORCE SHEAR MOMENT TORSION TORSION
TORSION
---------- -------- ------- -------- -------- -------- -------- --------- --------- --------- ---
------
Roof 6.459176 12.6 1.636622 0.0 0.0 0.0 0.0 0.0 0.0
0.0
10F 13.06699 12.4367 3.268004 0.0 0.0 0.0 0.0 0.0 0.0
0.0
9F 13.02067 12.2735 3.21367 0.0 0.0 0.0 0.0 0.0 0.0
0.0
8F 12.97535 12.1102 3.159884 0.0 0.0 0.0 0.0 0.0 0.0
0.0
7F 12.93159 11.9469 3.106771 0.0 0.0 0.0 0.0 0.0 0.0
0.0
6F 12.89035 11.7837 3.054541 0.0 0.0 0.0 0.0 0.0 0.0
0.0
5F 15.08228 11.6204 3.524431 0.0 0.0 0.0 0.0 0.0 0.0
0.0
4F 441.8094 11.4 101.2839 0.0 0.0 0.0 0.0 0.0 0.0
0.0
3F 2246.798 7.8 352.419 0.0 0.0 0.0 0.0 0.0 0.0
0.0
2F 2570.404 4.2 217.0958 0.0 0.0 0.0 0.0 0.0 0.0
0.0
G.L. -- 0.0 -- -- -- 0.0 0.0 --- ---
---
-------------------------------------------------------------------------------------------------
------
=================================================
COMMENTS ABOUT TORSION
=================================================
-------------------------------------------------------------------------------------------------
------
If torsional amplification effects are considered :
-------------------------------------------------------------------------------------------------
------
Accidental Torsion , Story Force * Accidental Eccentricity * Amp. Factor for Accidental
Eccentricity
Inherent Torsion , Story Force * Inherent Eccentricity * Amp. Factor for Inherent Eccentricity
-------------------------------------------------------------------------------------------------
------
If torsional amplification effects are not considered :
-------------------------------------------------------------------------------------------------
------
Accidental Torsion , Story Force * Accidental Eccentricity
Inherent Torsion , 0
-------------------------------------------------------------------------------------------------
------
The inherent torsion above is the additional torsion due to torsional amplification effect.
The true inherent torsion is considered automatically in analysis stage when the seismic force is
applied to the structure.
-------------------------------------------------------------------------------------------------
------
< Seismic Load >
[ LOAD CASE : EY+ ]
CODE = UBC.1997
-------------------------------------------------------------------------------------------------
-----
* MASS GENERATION DATA FOR LATERAL ANALYSIS OF BUILDING [UNIT: kN, m]
_________________________________________________________
STORY TRANSLATIONAL MASS ROTATIONAL CENTER OF MASS
NAME (X-DIR) (Y-DIR) MASS (X-COORD) (Y-COORD)
----------- ----------- ----------- ----------- ----------- -----------
Roof 0.0 0.0 0.0 0.0 0.0
10F 0.0 0.0 0.0 0.0 0.0
9F 0.0 0.0 0.0 0.0 0.0
8F 0.0 0.0 0.0 0.0 0.0
7F 0.0 0.0 0.0 0.0 0.0
6F 0.0 0.0 0.0 0.0 0.0
5F 0.0 0.0 0.0 0.0 0.0
4F 0.0 0.0 0.0 0.0 0.0
3F 229.124841 229.124841 12559.3962 8.54526098 7.90226119
2F 262.125665 262.125665 14423.2849 8.10800711 7.33476108
1F 0.0 0.0 0.0 0.0 0.0
----------- ----------- ----------- ----------- ----------- -----------
TOTAL : 491.250506 491.250506
* ADDITIONAL MASSES FOR THE CALCULATION OF EQUIVALENT SEISMIC FORCE
_____________________________________________________________________
Note. The following masses are between two adjacent stories or on the
nodes released from floor rigid diaphragm by *Diaphragm Disconnect command.
The masses are proportionally distributed to upper/lower stories according
to their vertical locations. For dynamic analysis, however, floor masses
and masses on vertical elements remain at their original locations.
STORY TRANSLATIONAL MASS
NAME (X-DIR) (Y-DIR)
-------------- ----------- -----------
Roof 0.65869628 0.65869628
10F 1.33255034 1.33255034
9F 1.32782658 1.32782658
8F 1.32320497 1.32320497
7F 1.3187427 1.3187427
6F 1.31453694 1.31453694
5F 1.5380663 1.5380663
4F 45.0550083 45.0550083
3F 0.0 0.0
2F 0.0 0.0
1F 15.1006099 15.1006099
-------------- ----------- -----------
TOTAL : 68.9692423 68.9692423
* EQUIVALENT SEISMIC LOAD IN ACCORDANCE WITH UNIFORM BUILDING CODE 1997 [UNIT: kN, m]
_____________________________________________________________________________________________
Seismic Zone Factor (Z) : 0.40
Importance Factor (I) : 1.00
Soil Profile Type : SD
Seismic Source Type : A
Closest Distance To Known Seismic Source [km] : 18.70
Near Source Factor, Na (UBC-97 Table 16-S) : 1.00
Near Source Factor, Nv (UBC-97 Table 16-T) : 1.00
Seismic Coefficient, Ca (UBC-97 Table 16-Q) : 0.44
Seismic Coefficient, Cv (UBC-97 Table 16-R) : 0.64
Fundamental Period Associated With X-dir. (Tx) : 0.4537
R Factor of Lateral System for X-direction (Rx) : 8.5000
Seismic Coefficient for X-dir. UBC-97(Para.1630.2.1) : 0.129412
Fundamental Period Associated With Y-dir. (Ty) : 0.4537
R Factor of Lateral System for Y-direction (Ry) : 8.5000
Seismic Coefficient for Y-dir. UBC-97(Para.1630.2.1) : 0.129412
Total Effective Weight For X-dir. Seismic Loads (Wx) : 5345.438268
Total Effective Weight For Y-dir. Seismic Loads (Wy) : 5345.438268
Scale Factor For X-directional Seismic Loads : 0.00
Scale Factor For Y-directional Seismic Loads : 1.00
Accidental Eccentricity For X-direction (Ex) : None
Accidental Eccentricity For Y-direction (Ey) : None
Torsional Amplification for Accidental Eccentricity : Do not Consider
Torsional Amplification for Inherent Eccentricity : Do not Consider
Total Base Shear Of Model For X-direction : 0.000000
Total Base Shear Of Model For Y-direction : 691.762599
Summation Of Wi*Hi Of Model For X-direction : 0.000000
Summation Of Wi*Hi Of Model For Y-direction : 34399.841088
--------------------------------------------------------------------------------------
===========================
ECCENTRICITY RELATED DATA
===========================
X - D I R E C T I O N A L L O A D Y - D I R E C T I O N A L L O A
D
STORY ACCIDENTAL INHERENT ACCIDENTAL INHERENT ACCIDENTAL INHERENT ACCIDENTAL
INHERENT
NAME ECCENT. ECCENT. [Link] [Link] ECCENT. ECCENT. [Link]
[Link]
---------- ---------- ---------- ---------- ---------- ---------- ---------- ---------- ----
------
Roof 0.0 0.0 1.0 0.0 0.0 0.0 1.0
0.0
10F 0.0 0.0 1.0 0.0 0.0 0.0 1.0
0.0
9F 0.0 0.0 1.0 0.0 0.0 0.0 1.0
0.0
8F 0.0 0.0 1.0 0.0 0.0 0.0 1.0
0.0
7F 0.0 0.0 1.0 0.0 0.0 0.0 1.0
0.0
6F 0.0 0.0 1.0 0.0 0.0 0.0 1.0
0.0
5F 0.0 0.0 1.0 0.0 0.0 0.0 1.0
0.0
4F 0.0 0.0 1.0 0.0 0.0 0.0 1.0
0.0
3F 0.0 0.0 1.0 0.0 0.0 0.0 1.0
0.0
2F 0.0 0.0 1.0 0.0 0.0 0.0 1.0
0.0
G.L 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0
-------------------------------------------------------------------------------------------------
------
-------------------------------------------------------------------------------------------------
------
The accidental amplification factors are automatically set to 1.0 when torsional amplification
effect
to accidental eccentricity is not considered.
The inherent amplification factors are automatically set to 0 when torsional amplification effect
to inherent eccentricity is not considered.
The inherent amplification factors are all set to 'the input value - 1.0'.(This is to exclude the
true
inherent torsion)
-------------------------------------------------------------------------------------------------
------
** Story Force , Seismic Force x Scale Factor + Added Force
S E I S M I C L O A D G E N E R A T I O N D A T A X - D I R E C T I O N
STORY STORY STORY SEISMIC ADDED STORY STORY OVERTURN. ACCIDENT. INHERENT
TOTAL
NAME WEIGHT LEVEL FORCE FORCE FORCE SHEAR MOMENT TORSION TORSION
TORSION
---------- -------- ------- -------- -------- -------- -------- --------- --------- --------- ---
------
Roof 6.459176 12.6 1.636622 0.0 0.0 0.0 0.0 0.0 0.0
0.0
10F 13.06699 12.4367 3.268004 0.0 0.0 0.0 0.0 0.0 0.0
0.0
9F 13.02067 12.2735 3.21367 0.0 0.0 0.0 0.0 0.0 0.0
0.0
8F 12.97535 12.1102 3.159884 0.0 0.0 0.0 0.0 0.0 0.0
0.0
7F 12.93159 11.9469 3.106771 0.0 0.0 0.0 0.0 0.0 0.0
0.0
6F 12.89035 11.7837 3.054541 0.0 0.0 0.0 0.0 0.0 0.0
0.0
5F 15.08228 11.6204 3.524431 0.0 0.0 0.0 0.0 0.0 0.0
0.0
4F 441.8094 11.4 101.2839 0.0 0.0 0.0 0.0 0.0 0.0
0.0
3F 2246.798 7.8 352.419 0.0 0.0 0.0 0.0 0.0 0.0
0.0
2F 2570.404 4.2 217.0958 0.0 0.0 0.0 0.0 0.0 0.0
0.0
G.L. -- 0.0 -- -- -- 0.0 0.0 --- ---
---
-------------------------------------------------------------------------------------------------
------
S E I S M I C L O A D G E N E R A T I O N D A T A Y - D I R E C T I O N
STORY STORY STORY SEISMIC ADDED STORY STORY OVERTURN. ACCIDENT. INHERENT
TOTAL
NAME WEIGHT LEVEL FORCE FORCE FORCE SHEAR MOMENT TORSION TORSION
TORSION
---------- -------- ------- -------- -------- -------- -------- --------- --------- --------- ---
------
Roof 6.459176 12.6 1.636622 0.0 1.636622 0.0 0.0 0.0 0.0
0.0
10F 13.06699 12.4367 3.268004 0.0 3.268004 1.636622 0.267204 0.0 0.0
0.0
9F 13.02067 12.2735 3.21367 0.0 3.21367 4.904625 1.067959 0.0 0.0
0.0
8F 12.97535 12.1102 3.159884 0.0 3.159884 8.118295 2.393395 0.0 0.0
0.0
7F 12.93159 11.9469 3.106771 0.0 3.106771 11.27818 4.23473 0.0 0.0
0.0
6F 12.89035 11.7837 3.054541 0.0 3.054541 14.38495 6.583293 0.0 0.0
0.0
5F 15.08228 11.6204 3.524431 0.0 3.524431 17.43949 9.430557 0.0 0.0
0.0
4F 441.8094 11.4 101.2839 0.0 101.2839 20.96392 14.05118 0.0 0.0
0.0
3F 2246.798 7.8 352.419 0.0 352.419 122.2478 454.1434 0.0 0.0
0.0
2F 2570.404 4.2 217.0958 0.0 217.0958 474.6668 2162.944 0.0 0.0
0.0
G.L. -- 0.0 -- -- -- 691.7626 5068.347 --- ---
---
-------------------------------------------------------------------------------------------------
------
=================================================
COMMENTS ABOUT TORSION
=================================================
-------------------------------------------------------------------------------------------------
------
If torsional amplification effects are considered :
-------------------------------------------------------------------------------------------------
------
Accidental Torsion , Story Force * Accidental Eccentricity * Amp. Factor for Accidental
Eccentricity
Inherent Torsion , Story Force * Inherent Eccentricity * Amp. Factor for Inherent Eccentricity
-------------------------------------------------------------------------------------------------
------
If torsional amplification effects are not considered :
-------------------------------------------------------------------------------------------------
------
Accidental Torsion , Story Force * Accidental Eccentricity
Inherent Torsion , 0
-------------------------------------------------------------------------------------------------
------
The inherent torsion above is the additional torsion due to torsional amplification effect.
The true inherent torsion is considered automatically in analysis stage when the seismic force is
applied to the structure.
-------------------------------------------------------------------------------------------------
------
< Load Combination >
** STEEL DESIGN
NO NAME TYPE ACTIVE DESCRIPTION
-------- ---------- ---------- ---------- ---------------------------------------------
1 sLCB1 Add ACTIVE 1.4D
2 sLCB2 Add ACTIVE 1.2(D) + 1.6(L) + 0.5LR
3 sLCB3 Add ACTIVE 1.2D + 1.6LR + 1.0L
4 sLCB4 Add ACTIVE 1.2D + 1.6LR + 0.5WL
5 sLCB5 Add ACTIVE 1.2D + 1.6LR - 0.5WL
6 sLCB6 Add ACTIVE 1.2D + 1.0WL + 1.0L + 0.5LR
7 sLCB7 Add ACTIVE 1.2D - 1.0WL + 1.0L + 0.5LR
8 sLCB12 Add ACTIVE 0.9D + 1.0WL
9 sLCB13 Add ACTIVE 0.9D - 1.0WL
10 sLCB14 Add ACTIVE 0.9D + 1.0EX+
11 sLCB15 Add ACTIVE 0.9D + 1.0EY+
12 sLCB16 Add ACTIVE 0.9D - 1.0EX+
13 sLCB17 Add ACTIVE 0.9D - 1.0EY+
** CONCRETE DESIGN
NO NAME TYPE ACTIVE DESCRIPTION
-------- ---------- ---------- ---------- ---------------------------------------------
1 cLCB1 Add STRENGTH 1.4(D)
2 cLCB2 Add STRENGTH 1.2(D) + 1.6L + 0.5LR
3 cLCB3 Add STRENGTH 1.2D + 1.6LR + 1.0(1.0(0.5)L)
4 cLCB4 Add STRENGTH 1.2D + 1.6LR + 0.5WL
5 cLCB5 Add STRENGTH 1.2D + 1.6LR - 0.5WL
6 cLCB6 Add STRENGTH 1.2D + 1.0WL + 1.0(1.0(0.5)L) + 0.5LR
7 cLCB7 Add STRENGTH 1.2D - 1.0WL + 1.0(1.0(0.5)L) + 0.5LR
8 cLCB8 Add STRENGTH 1.2D + 1.0EX+ + 1.0(1.0(0.5)L)
9 cLCB9 Add STRENGTH 1.2D + 1.0EY+ + 1.0(1.0(0.5)L)
10 cLCB10 Add STRENGTH 1.2D - 1.0EX+ + 1.0(1.0(0.5)L)
11 cLCB11 Add STRENGTH 1.2D - 1.0EY+ + 1.0(1.0(0.5)L)
12 cLCB12 Add STRENGTH 0.9D + 1.0WL
13 cLCB13 Add STRENGTH 0.9D - 1.0WL
14 cLCB14 Add STRENGTH 0.9D + 1.0EX+
15 cLCB15 Add STRENGTH 0.9D + 1.0EY+
16 cLCB16 Add STRENGTH 0.9D - 1.0EX+
17 cLCB17 Add STRENGTH 0.9D - 1.0EY+
18 cLCB18 Add SERVICE SERV :(D)
19 cLCB19 Add SERVICE SERV :(D) + (L)
20 cLCB20 Add SERVICE SERV :(D) + LR
21 cLCB21 Add SERVICE SERV :(D) + 0.75(L+LR)
22 cLCB22 Add SERVICE SERV :(D) + 0.75(L)
23 cLCB23 Add SERVICE SERV :(D) + 0.6WL
24 cLCB24 Add SERVICE SERV :(D) - 0.6WL
25 cLCB25 Add SERVICE SERV :(D) + EX+/1.4
26 cLCB26 Add SERVICE SERV :(D) + EY+/1.4
27 cLCB27 Add SERVICE SERV :(D) - EX+/1.4
28 cLCB28 Add SERVICE SERV :(D) - EY+/1.4
< Self Weight >
[ LOAD CASE : SELF WEIGHT ]
; X=0, Y=0, Z=-1
< Nodal Load >
[ LOAD CASE : DL ]
NODE FX FY FZ MX MY MZ
-------- ---------- ---------- ---------- ---------- ---------- ----------
2 0 0 -8.9 0 0 0
3 0 0 -8.9 0 0 0
4 0 0 -8.9 0 0 0
24 0 0 -8.9 0 0 0
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : C1(64)
1. General Information
(1) Design Code : ACI318M-14
(2) Code Unit : N, mm
2. Material
(1) F'c : 21.00MPa
(2) Fy : 420MPa
(3) Fys : 227MPa
450
3. Section
(1) Section Size : 450 x 450mm
(2) Lx : 3.600m
(3) Ly : 3.600m
(4) Kx : 1.000
(5) Ky : 1.000
(6) Splicing Limit : 0%
(7) Frame Type : Braced Frame 450
4. Load Combinations
General Forces Factors
Pu Mux Muy Vux Vuy
No CHK Name Cmx Cmy βd
(kN) (kN·m) (kN·m) (kN) (kN)
- PM cLCB10(64-J) 140 -22.47 93.89 -50.67 11.43 0.850 0.850 1.000
- Vx cLCB10(64-J) 140 -22.47 93.89 -50.67 11.43 0.850 0.850 1.000
- Vy cLCB9(64-J) 190 -60.32 30.02 -15.70 28.06 0.850 0.850 0.835
1 Yes cLCB1(64-I) 209 20.98 -18.44 -11.29 12.64 0.850 0.850 1.000
2 Yes cLCB1(64-J) 185 -24.52 22.19 -11.29 12.64 0.850 0.850 1.000
3 Yes cLCB2(64-I) 214 20.21 -20.57 -12.48 12.01 0.850 0.850 0.837
4 Yes cLCB2(64-J) 193 -23.03 24.34 -12.48 12.01 0.850 0.850 0.819
5 Yes cLCB3(64-I) 190 18.72 -17.40 -10.61 11.21 0.850 0.850 0.941
6 Yes cLCB3(64-J) 169 -21.63 20.79 -10.61 11.21 0.850 0.850 0.934
7 Yes cLCB4(64-I) 180 18.35 -15.97 -9.770 10.96 0.850 0.850 0.995
8 Yes cLCB4(64-J) 159 -21.13 19.20 -9.770 10.96 0.850 0.850 0.994
9 Yes cLCB5(64-I) 179 17.71 -15.86 -9.705 10.72 0.850 0.850 1.000
10 Yes cLCB5(64-J) 158 -20.87 19.08 -9.705 10.72 0.850 0.850 1.000
11 Yes cLCB6(64-I) 191 19.32 -17.43 -10.63 11.45 0.850 0.850 0.936
12 Yes cLCB6(64-J) 171 -21.90 20.83 -10.63 11.45 0.850 0.850 0.928
13 Yes cLCB7(64-I) 189 18.06 -17.20 -10.50 10.96 0.850 0.850 0.949
14 Yes cLCB7(64-J) 168 -21.38 20.59 -10.50 10.96 0.850 0.850 0.942
15 Yes cLCB8(64-I) 219 18.67 53.97 29.59 10.97 0.850 0.850 0.816
16 Yes cLCB8(64-J) 199 -20.82 -52.54 29.59 10.97 0.850 0.850 0.797
17 Yes cLCB9(64-I) 210 40.69 -26.49 -15.70 28.06 0.850 0.850 0.851
18 Yes cLCB9(64-J) 190 -60.32 30.02 -15.70 28.06 0.850 0.850 0.835
19 Yes cLCB10(64-I) 160 18.67 -88.54 -50.67 11.43 0.850 0.850 1.000
20 Yes cLCB10(64-J) 140 -22.47 93.89 -50.67 11.43 0.850 0.850 1.000
21 Yes cLCB11(64-I) 169 -3.347 -8.072 -5.387 -5.660 0.850 0.850 1.000
22 Yes cLCB11(64-J) 149 17.03 11.32 -5.387 -5.660 0.850 0.850 1.000
23 Yes cLCB12(64-I) 136 14.12 -11.97 -7.320 8.371 0.850 0.850 0.990
24 Yes cLCB12(64-J) 120 -16.02 14.39 -7.320 8.371 0.850 0.850 0.989
25 Yes cLCB13(64-I) 133 12.85 -11.74 -7.190 7.877 0.850 0.850 1.000
26 Yes cLCB13(64-J) 117 -15.50 14.14 -7.190 7.877 0.850 0.850 1.000
2023-09-15 07:51 1
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : C1(64)
27 Yes cLCB14(64-I) 164 13.49 59.40 32.88 7.895 0.850 0.850 0.820
28 Yes cLCB14(64-J) 148 -14.93 -58.95 32.88 7.895 0.850 0.850 0.801
29 Yes cLCB15(64-I) 155 35.51 -21.06 -12.41 24.98 0.850 0.850 0.868
30 Yes cLCB15(64-J) 139 -54.43 23.62 -12.41 24.98 0.850 0.850 0.853
31 Yes cLCB16(64-I) 105 13.49 -83.11 -47.39 8.353 0.850 0.850 1.000
32 Yes cLCB16(64-J) 89.34 -16.59 87.48 -47.39 8.353 0.850 0.850 1.000
33 Yes cLCB17(64-I) 114 -8.534 -2.642 -2.099 -8.736 0.850 0.850 1.000
34 Yes cLCB17(64-J) 98.33 22.91 4.915 -2.099 -8.736 0.850 0.850 1.000
5. Rebar
(1) Main Bar
Layer-1 : 10 - 4 - P25 ( Cc = 40.00mm, As = 4,909mm² )
Layer-2 :-
Layer-3 :-
Layer-4 :-
[Link] : 4,909mm²
(2) Hoop Bar
End : P10@100
Middle : P10@150
(3) Tie Bar
Apply Tie Bar to Shear Check : No
6. Calculation Summary
(1) Check Design Parameter
Category Value Criteria Ratio Note
Rebar Ratio ( Min. ) 0.0242 0.0100 0.413 ρmin / ρ
Rebar Ratio ( Max. ) 0.0242 0.0800 0.303 ρ / ρmax
(2) Check Moment Capacity ( Neutral axis )
Category Value Criteria Ratio Note
Moment Capacity ( Dir. X ) ( kN·m ) 22.47 80.41 0.279 Mux / øMnx
Moment Capacity ( Dir. Y ) ( kN·m ) 93.89 339 0.277 Muy / øMny
Axial Capacity ( kN ) 140 515 0.272 Pu / øPn
Moment Capacity ( kN·m ) 96.54 348 0.277 Mu / øMn
(3) Check Shear Capacity
Category Value Criteria Ratio Note
Shear Strength ( Dir. X ) ( kN ) 50.67 223 0.227 Vux / øVnx
Spacing Limits for Reinforcement ( Dir. X ) ( mm )100 400 0.250 sx / sx,max
Shear Strength ( Dir. Y ) ( kN ) 28.06 223 0.126 Vux / øVnx
Spacing Limits for Reinforcement ( Dir. Y ) ( mm )100 400 0.250 sy / sy,max
7. Check slenderness ratio
(1) Calculate radii of gyration
rx = 0.3D = 135mm
ry = 0.3B = 135mm
(2) Calculate slenderness ratio
M1x
= 0.625
M2x
M1y
= 0.625
M2y
2023-09-15 07:51 2
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : C1(64)
kx lux M1x
= 26.67 > min(34 + 12 , 40.0) = 26.50 → Slender
rx M2x
ky luy M1y
= 26.67 > min(34 + 12 , 40.0) = 26.50 → Slender
ry M2y
8. Check Magnified Moment
(1) Calculate modulus of elasticity
Ec = 4700 f'c = 21,538MPa
(2) Calculate moment magnification factor (Direction X)
Ig.x = BD3 / 12 = 3.417187e+9mm⁴
Ise.x = 108,465,197mm⁴
0.2Ec Ig.x + Es Ise.x
EIx = = 1.820646e+13N·mm²
1 + βdns
2 2
Pc.x = π EIx / (klu ) = 13,865kN
Cm
δns.x = = 1.000
1- Pu / 0.75Pc.x
(3) Calculate moment magnification factor (Direction Y)
Ig.y = DB3 / 12 = 3.417187e+9mm⁴
Ise.y = 134,600,168mm⁴
0.2Ec Ig.y + Es Ise.y
EIy = = 2.081996e+13N·mm²
1 + βdns
Pc.y = π2 EIy / (klu )2 = 15,855kN
Cm
δns.y = = 1.000
1- Pu / 0.75Pc.y
9. Check Minimum Moment
(1) Calculate minimum eccentricity
emin.x = 15 + 0.03D = 28.50mm
emin.y = 15 + 0.03B = 28.50mm
(2) Calculate minimum moment
Mmin.x = Pu emin.x = 3.985kN·m
Mmin.y = Pu emin.y = 3.985kN·m
10. Check design moment
(1) Calculate design moment
Mc.x = δns.x ㆍ max(Mmin.x , Mux ) = 22.47kN·m
Mc.y = δns.y ㆍ max(Mmin.y , Muy ) = 93.89kN·m
Mc = 96.54kN·m
11. Check Design Parameter
Calculation Summary ( Check Design Parameter )
Category Value Criteria Ratio Note
Rebar Ratio ( Min. ) 0.0242 0.0100 0.413 ρmin / ρ
Rebar Ratio ( Max. ) 0.0242 0.0800 0.303 ρ / ρmax
Rebar Ratio ( Min. ) 0.41
Rebar Ratio ( Max. ) 0.30
0.00 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80 0.90 1.00 1.10 1.20 1.30 1.40 1.50
(1) Calculate rebar ratio
Ag = 202,500mm², Ast = 4,909mm²
ρmin = 0.0100, ρmax = 0.0800, ρ = 0.0242
ρmin < ρ < ρmax → O.K
(2) Calculate eccentricity
ex = Mc.y / Pu = 671mm
ey = Mc.x / Pu = 161mm
2023-09-15 07:51 3
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : C1(64)
e = Mc / Pu = 690mm
Rotation angle of neutral axis = 71.75°
(3) Calculate concentric axial load capacity
P0 = 0.85f'c ( Ag - Ast ) + fy Ast = 5,589kN
[Link] = 0.80P0 = 4,471kN
Pt = fy Ast = -2,062kN
12. Check Moment Capacity ( Balanced axis )
(1) Calculate capacity of compression stress block
β1 = 0.850
c = 305mm, a = β1 ㆍ c = 259mm
Acom = 89,283mm²
ccx = 121mm, ccy = 28.04mm
Cc = 0.85 ㆍ f'c ㆍ Acom = 1,594kN
Mnx = Cc ㆍ ccy = 44.69kN·m
Mny = Cc ㆍ ccx = 193kN·m
(2) Calculate capacity of rebar
ds fs As Fs dy Mnx dx Mny
i εs
(mm) (MPa) (mm²) (kN) (mm) (kN) (mm) (kN)
1 518 -0.002100 -420 491 -206 -185 38.14 -185 38.14
2 479 -0.001720 -344 491 -169 -61.67 10.41 -185 31.23
3 441 -0.001339 -268 491 -131 61.67 -8.109 -185 24.33
4 402 -0.000959 -192 491 -94.15 185 -17.42 -185 17.42
5 226 0.000772 154 491 75.77 185 14.02 0.000 0.000
6 50.51 0.002502 420 491 206 185 38.14 185 38.14
7 89.13 0.002122 420 491 206 61.67 12.71 185 38.14
8 128 0.001742 348 491 171 -61.67 -10.55 185 31.64
9 166 0.001361 272 491 134 -185 -24.73 185 24.73
10 342 -0.000369 -73.87 491 -36.26 -185 6.708 0.000 0.000
∑Fs = 156kN
∑Mnx = 59.34kN·m
∑Mny = 244kN·m
(3) Calculate nominal capacity for neutral axis
Pb = Cc + Ps = 1,750kN
Mnx = [Link] + [Link] = 104kN·m
Mny = [Link] + [Link] = 437kN·m
2 2
Mn = ( Mnx ) + ( Mny ) = 449kN·m
13. Check Moment Capacity ( Neutral axis )
Calculation Summary ( Check Moment Capacity ( Neutral axis ) )
Category Value Criteria Ratio Note
Moment Capacity ( Dir. X ) ( kN·m ) 22.47 80.41 0.279 Mux / øMnx
Moment Capacity ( Dir. Y ) ( kN·m ) 93.89 339 0.277 Muy / øMny
Axial Capacity ( kN ) 140 515 0.272 Pu / øPn
Moment Capacity ( kN·m ) 96.54 348 0.277 Mu / øMn
Moment Capacity ( Dir. X ) 0.28
Moment Capacity ( Dir. Y ) 0.28
Axial Capacity 0.27
Moment Capacity 0.28
0.00 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80 0.90 1.00 1.10 1.20 1.30 1.40 1.50
(1) Calculate capacity of compression stress block
2023-09-15 07:51 4
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : C1(64)
c = 226mm, a = β1 ㆍ c = 192mm
Acom = 57,465mm²
ccx = 154mm, ccy = 43.56mm
Cc = 0.85 ㆍ fck ㆍ Acom = 1,026kN
Mnx = Cc ㆍ ccy = 44.69kN·m
Mny = Cc ㆍ ccx = 158kN·m
(2) Calculate capacity of rebar
ds fs As Fs dy Mnx dx Mny
i εs
(mm) (MPa) (mm²) (kN) (mm) (kN) (mm) (kN)
1 518 -0.003886 -420 491 -206 -185 38.14 -185 38.14
2 479 -0.003373 -420 491 -206 -61.67 12.71 -185 38.14
3 441 -0.002859 -420 491 -206 61.67 -12.71 -185 38.14
4 402 -0.002345 -420 491 -206 185 -38.14 -185 38.14
5 226 -0.000009 -1.732 491 -0.850 185 -0.157 0.000 0.000
6 50.51 0.002328 420 491 206 185 38.14 185 38.14
7 89.13 0.001815 363 491 178 61.67 10.99 185 32.96
8 128 0.001301 260 491 128 -61.67 -7.877 185 23.63
9 166 0.000787 157 491 77.31 -185 -14.30 185 14.30
10 342 -0.001549 -310 491 -152 -185 28.14 0.000 0.000
∑Fs = -388kN
∑Mnx = 54.94kN·m
∑Mny = 262kN·m
(3) Calculate nominal capacity for neutral axis
Pn = Cc + Ps = 637kN
Mnx = [Link] + [Link] = 99.62kN·m
Mny = [Link] + [Link] = 420kN·m
Mn = ( Mnx )2 + ( Mny )2 = 431kN·m
(4) Calculate strength reduction factor
ε[Link] = 0.0021, ε[Link] = 0.0050
εt = 0.003886
ø = 0.807
(5) Calculate axial load and moment capacities
øPn = 515kN
øMnx = 80.41kN·m
øMny = 339kN·m
øMn = 348kN·m
Mux / øMnx = 0.279 < 1.000 → O.K
Muy / øMny = 0.277 < 1.000 → O.K
Pu / øPn = 0.272 < 1.000 → O.K
Mc / øMn = 0.277 < 1.000 → O.K
2023-09-15 07:51 5
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : C1(64)
P (kN)
5750
θ=76.64˚
N.A=71.75˚
4950
4150
3350
2906
2550
1750 eb=304.56mm
950
(515,348)
150 (140,97) M (kN·m)
0
-650
-1450
-2250
0
50
100
150
200
250
300
350
400
450
500
14. Check Shear Capacity
Calculation Summary ( Check Shear Capacity )
Category Value Criteria Ratio Note
Shear Strength ( Dir. X ) ( kN ) 50.67 223 0.227 Vux / øVnx
Spacing Limits for Reinforcement ( Dir. X ) ( mm )100 400 0.250 sx / sx,max
Shear Strength ( Dir. Y ) ( kN ) 28.06 223 0.126 Vux / øVnx
Spacing Limits for Reinforcement ( Dir. Y ) ( mm )100 400 0.250 sy / sy,max
Shear Strength ( Dir. X ) 0.23
Spacing Limits for Reinforcement ( Dir. X ) 0.25
Shear Strength ( Dir. Y ) 0.13
Spacing Limits for Reinforcement ( Dir. Y ) 0.25
0.00 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80 0.90 1.00 1.10 1.20 1.30 1.40 1.50
(1) Calculate maximum space
ø = 0.750
Smax = min(16DMainBar , 48DStirrup , B, D) = 400mm
(2) Calculate Shear Strength (Direction X)
s = 100mm < smax = 400mm → O.K
Nu
øVc = ø0.17 (1+ ) f'c bw d = 113kN
14Ag
Av fyt d
øVs = ø = 110kN
s
øVn = øVc + øVs = 223kN
Vu / øVn = 0.227 → O.K
(3) Calculate Shear Strength (Direction Y)
s = 100mm < smax = 400mm → O.K
Nu
øVc = ø0.17 (1+ ) f'c bw d = 113kN
14Ag
Av fyt d
øVs = ø = 110kN
s
øVn = øVc + øVs = 223kN
2023-09-15 07:51 6
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : C1(64)
Vu / øVn = 0.126 → O.K
2023-09-15 07:51 7
midas Gen RC Column Design Result
Company Project Title
Author JPPES File Name HUANG CB [Link]
1. Design Condition z
Design Code : ACI318M-14 UNIT SYSTEM: kN, m
Member Number: 78 (PM), 78, 82 (Shear-y,z)
Material Data : fc = 20684.3, fy = 420000, fys = 230000 KPa
Column Height : 3.6 m
Section Property: C2 (No : 5)
0.45
Rebar Pattern : 6 - 3 - D25 Ast = 0.00294528 m^2 (Rhost = 0.019) y
2. Axial and Moments Capacity
0.0635
Load Combination : 11 (Pos : I)
Concentric Max. Axial Load phiPn-max = 2056.26 kN 0.35
Axial Load Ratio Pu / phiPn = 130.808 / 141.978 = 0.921 < 1.000 ....... O.K
Moment Ratio Mc / phiMn = 133.793 / 145.180 = 0.922 < 1.000 ....... O.K
Mcy / phiMny = -62.983 / 68.1567 = 0.924 < 1.000 ....... O.K
Mcz / phiMnz = -118.04 / 128.187 = 0.921 < 1.000 ....... O.K
P-M Interaction Diagram
P(kN)4000
phiPn(kN) phiMn(kN-m)
3475 Theta=62.00Deg.
N.A=68.94Deg. 2570.32 0.00
2950 2272.95 42.59
2425 1975.44 79.53
2056 1580.37 110.19
1900
1195.32 127.99
1375 858.13 136.18
850 648.84 138.50
325
535.97 142.22
0 (142,145)
(131,134)
291.77 146.02
-200
M(kN-m) -75.12 141.61
-725 -550.83 97.23
-1250 -987.45 27.05
-1113.32 0.00
100
125
150
175
200
225
250
25
50
75
3. Shear Capacity
[ END ] y (LCB : 11, POS : J) z (LCB : 17, POS : J)
Applied Shear Force (Vu) 111.669 kN 92.0218 kN
Design Shear Strength (phiVc+phiVs)0.00000 + 293.175 = 293.175 kN 0.00000 + 307.615 = 307.615 kN
Shear Ratio 0.381 < 1.000 ....... O.K 0.299 < 1.000 ....... O.K
As-H_req 0.00226 m^2/m, 2-D10 @20 0.00138 m^2/m, 2-D10 @20
[ MIDDLE ] y (LCB : 11, POS : 1/2) z (LCB : 11, POS : 1/2)
Applied Shear Force (Vu) 111.669 kN 93.4940 kN
Design Shear Strength (phiVc+phiVs)78.9229 + 55.4506 = 134.374 kN 84.9464 + 69.8181 = 154.765 kN
Shear Ratio 0.831 < 1.000 ....... O.K 0.604 < 1.000 ....... O.K
As-H_req 0.00068 m^2/m, 2-D10 @140 0.00053 m^2/m, 2-D10 @140
[ JOINT : TOP ] y (LCB : 16, POS : J) z (LCB : 16, POS : J)
Joint Shear (Vhj/phiVnj) 477.068 / 608.863 = 0.784 487.110 / 608.863 = 0.800
Joint Ratio 0.784 < 1.000 ....... O.K 0.800 < 1.000 ....... O.K
Modeling, Integrated Design & Analysis Software Print Date/Time : 09/15/2023 07:52
midas Gen RC Column Design Result
Company Project Title
Author JPPES File Name HUANG CB [Link]
1. Design Condition z
Design Code : ACI318M-14 UNIT SYSTEM: kN, m
Member Number: 78 (PM), 78, 82 (Shear-y,z)
Material Data : fc = 20684.3, fy = 420000, fys = 230000 KPa
Column Height : 3.6 m
Section Property: C2 (No : 5)
0.45
Rebar Pattern : 6 - 3 - D25 Ast = 0.00294528 m^2 (Rhost = 0.019) y
2. Axial and Moments Capacity
0.0635
Load Combination : 11 (Pos : I)
Concentric Max. Axial Load phiPn-max = 2056.26 kN 0.35
Axial Load Ratio Pu / phiPn = 130.808 / 141.978 = 0.921 < 1.000 ....... O.K
Moment Ratio Mc / phiMn = 133.793 / 145.180 = 0.922 < 1.000 ....... O.K
Mcy / phiMny = -62.983 / 68.1567 = 0.924 < 1.000 ....... O.K
Mcz / phiMnz = -118.04 / 128.187 = 0.921 < 1.000 ....... O.K
P-M Interaction Diagram
P(kN)4000
phiPn(kN) phiMn(kN-m)
3475 Theta=62.00Deg.
N.A=68.94Deg. 2570.32 0.00
2950 2272.95 42.59
2425 1975.44 79.53
2056 1580.37 110.19
1900
1195.32 127.99
1375 858.13 136.18
850 648.84 138.50
325
535.97 142.22
0 (142,145)
(131,134)
291.77 146.02
-200
M(kN-m) -75.12 141.61
-725 -550.83 97.23
-1250 -987.45 27.05
-1113.32 0.00
100
125
150
175
200
225
250
25
50
75
3. Shear Capacity
[ END ] y (LCB : 11, POS : J) z (LCB : 17, POS : J)
Applied Shear Force (Vu) 111.669 kN 92.0218 kN
Design Shear Strength (phiVc+phiVs)0.00000 + 293.175 = 293.175 kN 0.00000 + 307.615 = 307.615 kN
Shear Ratio 0.381 < 1.000 ....... O.K 0.299 < 1.000 ....... O.K
As-H_req 0.00226 m^2/m, 2-D10 @20 0.00138 m^2/m, 2-D10 @20
[ MIDDLE ] y (LCB : 11, POS : 1/2) z (LCB : 11, POS : 1/2)
Applied Shear Force (Vu) 111.669 kN 93.4940 kN
Design Shear Strength (phiVc+phiVs)78.9229 + 55.4506 = 134.374 kN 84.9464 + 69.8181 = 154.765 kN
Shear Ratio 0.831 < 1.000 ....... O.K 0.604 < 1.000 ....... O.K
As-H_req 0.00068 m^2/m, 2-D10 @140 0.00053 m^2/m, 2-D10 @140
[ JOINT : TOP ] y (LCB : 16, POS : J) z (LCB : 16, POS : J)
Joint Shear (Vhj/phiVnj) 477.068 / 608.863 = 0.784 487.110 / 608.863 = 0.800
Joint Ratio 0.784 < 1.000 ....... O.K 0.800 < 1.000 ....... O.K
Modeling, Integrated Design & Analysis Software Print Date/Time : 09/15/2023 07:52
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 3C1(121)
1. General Information
(1) Design Code : ACI318M-14
(2) Code Unit : N, mm
2. Material
(1) F'c : 21.00MPa
(2) Fy : 420MPa
(3) Fys : 275MPa
350
3. Section
(1) Section Size : 300 x 350mm
(2) Lx : 3.600m
(3) Ly : 3.600m
(4) Kx : 1.000
(5) Ky : 1.000
(6) Splicing Limit : 0%
(7) Frame Type : Braced Frame 300
4. Load Combinations
General Forces Factors
Pu Mux Muy Vux Vuy
No CHK Name Cmx Cmy βd
(kN) (kN·m) (kN·m) (kN) (kN)
- PM cLCB10(121-J) 95.65 -30.99 30.72 -17.36 13.66 0.850 0.850 0.857
- Vx cLCB10(121-J) 95.65 -30.99 30.72 -17.36 13.66 0.850 0.850 0.857
- Vy cLCB9(121-J) 76.74 -43.39 8.873 -5.721 19.51 0.850 0.850 1.000
1 Yes cLCB1(121-I) 108 16.15 -14.42 -7.065 12.53 0.850 0.850 1.000
2 Yes cLCB1(121-J) 95.62 -28.95 11.01 -7.065 12.53 0.850 0.850 1.000
3 Yes cLCB2(121-I) 93.15 16.15 -12.99 -6.388 11.22 0.850 0.850 0.995
4 Yes cLCB2(121-J) 82.46 -24.24 10.01 -6.388 11.22 0.850 0.850 0.994
5 Yes cLCB3(121-I) 92.52 14.15 -12.58 -6.168 10.74 0.850 0.850 1.000
6 Yes cLCB3(121-J) 81.83 -24.53 9.626 -6.168 10.74 0.850 0.850 1.000
7 Yes cLCB4(121-I) 92.23 13.70 -12.40 -6.073 10.77 0.850 0.850 1.000
8 Yes cLCB4(121-J) 81.54 -25.07 9.465 -6.073 10.77 0.850 0.850 1.000
9 Yes cLCB5(121-I) 92.43 13.06 -12.37 -6.057 10.38 0.850 0.850 1.000
10 Yes cLCB5(121-J) 81.74 -24.32 9.435 -6.057 10.38 0.850 0.850 1.000
11 Yes cLCB6(121-I) 92.54 15.11 -12.59 -6.178 11.24 0.850 0.850 1.000
12 Yes cLCB6(121-J) 81.85 -25.36 9.649 -6.178 11.24 0.850 0.850 1.000
13 Yes cLCB7(121-I) 92.94 13.82 -12.53 -6.145 10.47 0.850 0.850 0.997
14 Yes cLCB7(121-J) 82.25 -23.86 9.590 -6.145 10.47 0.850 0.850 0.996
15 Yes cLCB8(121-I) 79.33 11.01 6.653 5.040 8.143 0.850 0.850 1.000
16 Yes cLCB8(121-J) 68.65 -18.31 -11.49 5.040 8.143 0.850 0.850 1.000
17 Yes cLCB9(121-I) 87.42 26.86 -11.72 -5.721 19.51 0.850 0.850 1.000
18 Yes cLCB9(121-J) 76.74 -43.39 8.873 -5.721 19.51 0.850 0.850 1.000
19 Yes cLCB10(121-I) 106 18.21 -31.76 -17.36 13.66 0.850 0.850 0.871
20 Yes cLCB10(121-J) 95.65 -30.99 30.72 -17.36 13.66 0.850 0.850 0.857
21 Yes cLCB11(121-I) 98.25 2.356 -13.39 -6.597 2.294 0.850 0.850 0.943
22 Yes cLCB11(121-J) 87.56 -5.903 10.36 -6.597 2.294 0.850 0.850 0.936
23 Yes cLCB12(121-I) 69.29 11.02 -9.299 -4.558 8.439 0.850 0.850 1.000
24 Yes cLCB12(121-J) 61.27 -19.36 7.111 -4.558 8.439 0.850 0.850 1.000
25 Yes cLCB13(121-I) 69.69 9.735 -9.241 -4.526 7.667 0.850 0.850 0.997
26 Yes cLCB13(121-J) 61.67 -17.86 7.051 -4.526 7.667 0.850 0.850 0.997
2023-09-15 07:55 1
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 3C1(121)
27 Yes cLCB14(121-I) 55.98 6.780 9.938 6.657 5.292 0.850 0.850 1.000
28 Yes cLCB14(121-J) 47.97 -12.27 -14.03 6.657 5.292 0.850 0.850 1.000
29 Yes cLCB15(121-I) 64.07 22.63 -8.436 -4.104 16.66 0.850 0.850 1.000
30 Yes cLCB15(121-J) 56.06 -37.35 6.337 -4.104 16.66 0.850 0.850 1.000
31 Yes cLCB16(121-I) 82.99 13.98 -28.48 -15.74 10.81 0.850 0.850 0.837
32 Yes cLCB16(121-J) 74.97 -24.95 28.19 -15.74 10.81 0.850 0.850 0.820
33 Yes cLCB17(121-I) 74.90 -1.871 -10.10 -4.980 -0.556 0.850 0.850 0.928
34 Yes cLCB17(121-J) 66.88 0.131 7.825 -4.980 -0.556 0.850 0.850 0.919
5. Rebar
(1) Main Bar
Layer-1 : 4 - 2 - P25 ( Cc = 40.00mm, As = 1,964mm² )
Layer-2 :-
Layer-3 :-
Layer-4 :-
[Link] : 1,964mm²
(2) Hoop Bar
End : P10@20.00
Middle : P10@150
(3) Tie Bar
Apply Tie Bar to Shear Check : No
6. Calculation Summary
(1) Check Design Parameter
Category Value Criteria Ratio Note
Rebar Ratio ( Min. ) 0.0187 0.0100 0.535 ρmin / ρ
Rebar Ratio ( Max. ) 0.0187 0.0800 0.234 ρ / ρmax
(2) Check Moment Capacity ( Neutral axis )
Category Value Criteria Ratio Note
Moment Capacity ( Dir. X ) ( kN·m ) 30.99 68.91 0.450 Mux / øMnx
Moment Capacity ( Dir. Y ) ( kN·m ) 30.72 68.41 0.449 Muy / øMny
Axial Capacity ( kN ) 95.65 212 0.451 Pu / øPn
Moment Capacity ( kN·m ) 43.63 97.10 0.449 Mu / øMn
(3) Check Shear Capacity
Category Value Criteria Ratio Note
Shear Strength ( Dir. X ) ( kN ) 17.36 478 0.0363 Vux / øVnx
Spacing Limits for Reinforcement ( Dir. X ) ( mm 2
) 0.00 300 0.0667 sx / sx,max
Shear Strength ( Dir. Y ) ( kN ) 19.51 560 0.0348 Vux / øVnx
Spacing Limits for Reinforcement ( Dir. Y ) ( mm 2
) 0.00 300 0.0667 sy / sy,max
7. Check slenderness ratio
(1) Calculate radii of gyration
rx = 0.3D = 105mm
ry = 0.3B = 90.00mm
(2) Calculate slenderness ratio
M1x
= 0.625
M2x
M1y
= 0.625
M2y
2023-09-15 07:55 2
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 3C1(121)
kx lux M1x
= 34.29 > min(34 + 12 , 40.0) = 26.50 → Slender
rx M2x
ky luy M1y
= 40.00 > min(34 + 12 , 40.0) = 26.50 → Slender
ry M2y
8. Check Magnified Moment
(1) Calculate modulus of elasticity
Ec = 4700 f'c = 21,538MPa
(2) Calculate moment magnification factor (Direction X)
Ig.x = BD3 / 12 = 1.071875e+9mm⁴
Ise.x = 35,863,309mm⁴
0.2Ec Ig.x + Es Ise.x
EIx = = 6.349377e+12N·mm²
1 + βdns
2 2
Pc.x = π EIx / (klu ) = 4,835kN
Cm
δns.x = = 1.000
1- Pu / 0.75Pc.x
(3) Calculate moment magnification factor (Direction Y)
Ig.y = DB3 / 12 = 787,500,000mm⁴
Ise.y = 23,836,259mm⁴
0.2Ec Ig.y + Es Ise.y
EIy = = 4.394252e+12N·mm²
1 + βdns
Pc.y = π2 EIy / (klu )2 = 3,346kN
Cm
δns.y = = 1.000
1- Pu / 0.75Pc.y
9. Check Minimum Moment
(1) Calculate minimum eccentricity
emin.x = 15 + 0.03D = 25.50mm
emin.y = 15 + 0.03B = 24.00mm
(2) Calculate minimum moment
Mmin.x = Pu emin.x = 2.439kN·m
Mmin.y = Pu emin.y = 2.296kN·m
10. Check design moment
(1) Calculate design moment
Mc.x = δns.x ㆍ max(Mmin.x , Mux ) = 30.99kN·m
Mc.y = δns.y ㆍ max(Mmin.y , Muy ) = 30.72kN·m
Mc = 43.63kN·m
11. Check Design Parameter
Calculation Summary ( Check Design Parameter )
Category Value Criteria Ratio Note
Rebar Ratio ( Min. ) 0.0187 0.0100 0.535 ρmin / ρ
Rebar Ratio ( Max. ) 0.0187 0.0800 0.234 ρ / ρmax
Rebar Ratio ( Min. ) 0.53
Rebar Ratio ( Max. ) 0.23
0.00 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80 0.90 1.00 1.10 1.20 1.30 1.40 1.50
(1) Calculate rebar ratio
Ag = 105,000mm², Ast = 1,964mm²
ρmin = 0.0100, ρmax = 0.0800, ρ = 0.0187
ρmin < ρ < ρmax → O.K
(2) Calculate eccentricity
ex = Mc.y / Pu = 321mm
ey = Mc.x / Pu = 324mm
2023-09-15 07:55 3
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 3C1(121)
e = Mc / Pu = 456mm
Rotation angle of neutral axis = 54.65°
(3) Calculate concentric axial load capacity
P0 = 0.85f'c ( Ag - Ast ) + fy Ast = 2,664kN
[Link] = 0.80P0 = 2,131kN
Pt = fy Ast = -825kN
12. Check Moment Capacity ( Balanced axis )
(1) Calculate capacity of compression stress block
β1 = 0.850
c = 230mm, a = β1 ㆍ c = 196mm
Acom = 40,584mm²
ccx = 70.02mm, ccy = 62.24mm
Cc = 0.85 ㆍ f'c ㆍ Acom = 724kN
Mnx = Cc ㆍ ccy = 45.09kN·m
Mny = Cc ㆍ ccx = 50.73kN·m
(2) Calculate capacity of rebar
ds fs As Fs dy Mnx dx Mny
i εs
(mm) (MPa) (mm²) (kN) (mm) (kN) (mm) (kN)
1 391 -0.002100 -420 491 -206 -135 27.83 -110 22.68
2 235 -0.000065 -12.95 491 -6.359 135 -0.859 -110 0.700
3 55.77 0.002273 420 491 206 135 27.83 110 22.68
4 212 0.000238 47.63 491 23.38 -135 -3.156 110 2.572
∑Fs = 17.02kN
∑Mnx = 51.65kN·m
∑Mny = 48.63kN·m
(3) Calculate nominal capacity for neutral axis
Pb = Cc + Ps = 741kN
Mnx = [Link] + [Link] = 96.74kN·m
Mny = [Link] + [Link] = 99.36kN·m
2 2
Mn = ( Mnx ) + ( Mny ) = 139kN·m
13. Check Moment Capacity ( Neutral axis )
Calculation Summary ( Check Moment Capacity ( Neutral axis ) )
Category Value Criteria Ratio Note
Moment Capacity ( Dir. X ) ( kN·m ) 30.99 68.91 0.450 Mux / øMnx
Moment Capacity ( Dir. Y ) ( kN·m ) 30.72 68.41 0.449 Muy / øMny
Axial Capacity ( kN ) 95.65 212 0.451 Pu / øPn
Moment Capacity ( kN·m ) 43.63 97.10 0.449 Mu / øMn
Moment Capacity ( Dir. X ) 0.45
Moment Capacity ( Dir. Y ) 0.45
Axial Capacity 0.45
Moment Capacity 0.45
0.00 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80 0.90 1.00 1.10 1.20 1.30 1.40 1.50
(1) Calculate capacity of compression stress block
c = 177mm, a = β1 ㆍ c = 151mm
Acom = 24,018mm²
ccx = 88.47mm, ccy = 88.25mm
Cc = 0.85 ㆍ fck ㆍ Acom = 429kN
Mnx = Cc ㆍ ccy = 37.84kN·m
Mny = Cc ㆍ ccx = 37.93kN·m
2023-09-15 07:55 4
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 3C1(121)
(2) Calculate capacity of rebar
ds fs As Fs dy Mnx dx Mny
i εs
(mm) (MPa) (mm²) (kN) (mm) (kN) (mm) (kN)
1 391 -0.003629 -420 491 -206 -135 27.83 -110 22.68
2 235 -0.000984 -197 491 -96.60 135 -13.04 -110 10.63
3 55.77 0.002055 411 491 202 135 27.24 110 22.20
4 212 -0.000590 -118 491 -57.94 -135 7.821 110 -6.373
∑Fs = -159kN
∑Mnx = 49.86kN·m
∑Mny = 49.13kN·m
(3) Calculate nominal capacity for neutral axis
Pn = Cc + Ps = 270kN
Mnx = [Link] + [Link] = 87.69kN·m
Mny = [Link] + [Link] = 87.06kN·m
Mn = ( Mnx )2 + ( Mny )2 = 124kN·m
(4) Calculate strength reduction factor
ε[Link] = 0.0021, ε[Link] = 0.0050
εt = 0.003629
ø = 0.786
(5) Calculate axial load and moment capacities
øPn = 212kN
øMnx = 68.91kN·m
øMny = 68.41kN·m
øMn = 97.10kN·m
Mux / øMnx = 0.450 < 1.000 → O.K
Muy / øMny = 0.449 < 1.000 → O.K
Pu / øPn = 0.451 < 1.000 → O.K
Mc / øMn = 0.449 < 1.000 → O.K
P (kN)
2750
θ=44.79˚
N.A=54.65˚
2375
2000
1625
1385
1250
875
eb=230.24mm
500
(212,97)
125 (96,44) M (kN·m)
0
-250
-625
-1000
0
15
30
45
60
75
90
105
120
135
150
14. Check Shear Capacity
2023-09-15 07:55 5
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 3C1(121)
Calculation Summary ( Check Shear Capacity )
Category Value Criteria Ratio Note
Shear Strength ( Dir. X ) ( kN ) 17.36 478 0.0363 Vux / øVnx
Spacing Limits for Reinforcement ( Dir. X ) ( mm 2
) 0.00 300 0.0667 sx / sx,max
Shear Strength ( Dir. Y ) ( kN ) 19.51 560 0.0348 Vux / øVnx
Spacing Limits for Reinforcement ( Dir. Y ) ( mm 2
) 0.00 300 0.0667 sy / sy,max
Shear Strength ( Dir. X ) 0.04
Spacing Limits for Reinforcement ( Dir. X ) 0.07
Shear Strength ( Dir. Y ) 0.03
Spacing Limits for Reinforcement ( Dir. Y ) 0.07
0.00 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80 0.90 1.00 1.10 1.20 1.30 1.40 1.50
(1) Calculate maximum space
ø = 0.750
Smax = min(16DMainBar , 48DStirrup , B, D) = 300mm
(2) Calculate Shear Strength (Direction X)
s = 20.00mm < smax = 300mm → O.K
Nu
øVc = ø0.17 (1+ ) f'c bw d = 56.63kN
14Ag
Av fyt d
øVs = ø = 421kN
s
øVn = øVc + øVs = 478kN
Vu / øVn = 0.0363 → O.K
(3) Calculate Shear Strength (Direction Y)
s = 20.00mm < smax = 300mm → O.K
Nu
øVc = ø0.17 (1+ ) f'c bw d = 57.87kN
14Ag
Av fyt d
øVs = ø = 503kN
s
øVn = øVc + øVs = 560kN
Vu / øVn = 0.0348 → O.K
2023-09-15 07:55 6
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 2B1
Section : BOTH END
1. General Information
(1) Design Code : ACI318M-14
(2) Code Unit : N, mm
2. Material
(1) F'c : 21.00MPa
(2) Fy : 275MPa
(3) Fys : 227MPa
3. Section
(1) Section Size : 250 x 625mm (R-Section)
(2) Cover : 40.00mm
(3) Compression : Not Considered
(4) Splicing Limit : 0%
250
40
625
40
4. Moments and Forces
(1) Mu,top : 257kN·m
(2) Mu,bottom : 96.90kN·m
(3) Vu : 127kN
5. Reinforcement
(1) Top Bar : 5-P25 (As = 2,455mm²)
Layer 1 : 3 EA (Cc = 62.50mm)
Layer 2 : 2 EA (Cc = 113mm)
(2) Bot Bar : 3-P25 (As = 1,473mm²)
Layer 1 : 3 EA (Cc = 62.50mm)
(3) Stirrup : 2-P10@100 (As = 157mm²)
6. Check Bending Moment Capacity (Positive)
(1) Calculate design parameter
β1 = 0.850
(2) Check space of rebar
280 280
smax1 = 380 ( ) - 2.5cc smax2 = 300 ( )
fs fs
2023-09-15 07:32 1
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 2B1
smax = min ( smax1 , smax2 ) = 455mm, Nreq = 2
s = 62.50 < 455mm → O.K
(3) Calculate required ratio of reinforcement
( f'c )1/2 1.4
ρmin.11 = 0.25 ρmin.12 =
fy fy
ρmin.1 = max ( ρmin.11 , ρmin.12 ) = 0.0051
4 Mu
ρmin.2 = = 0.0069
3 ø fy bd(d-a/2)
ρmin = min ( ρmin1 , ρmin2 ) = 0.0051
f'c εc
ρεt = 0.85 β1 ( )( ) = 0.0236
fy εc + 0.004
ρmax = ρet = 0.0236
(4) Check ratio of tensile reinforcement
As
ρ= = 0.0105
bw d
ρmin < ρ < ρmax → O.K
(5) Calculate moment capacity
As fy
a= = 90.75mm
0.85 f'c bw
ø = 0.900
Mn = As fy (d - a/2) = 209kN·m
øMn = 188kN·m
(6) Calculate ratio of moment capacity
Mu / øMn = 0.514 → O.K
7. Check Bending Moment Capacity (Negative)
(1) Calculate design parameter
β1 = 0.850
(2) Check space of rebar
280 280
smax1 = 380 ( ) - 2.5cc smax2 = 300 ( )
fs fs
smax = min ( smax1 , smax2 ) = 455mm, Nreq =2
s = 62.50 < 455mm → O.K
(3) Calculate required ratio of reinforcement
1/2
( f'c ) 1.4
ρmin.11 = 0.25 ρmin.12 =
fy fy
ρmin.1 = max ( ρmin.11 , ρmin.12 ) = 0.0051
4 Mu
ρmin.2 = = 0.0215
3 ø fy bd(d-a/2)
ρmin = min ( ρmin1 , ρmin2 ) = 0.0051
f'c εc
ρεt = 0.85 β1 ( )( ) = 0.0236
fy εc + 0.004
ρmax = ρet = 0.0236
(4) Check ratio of tensile reinforcement
As
ρ= = 0.0181
bw d
ρmin < ρ < ρmax → O.K
(5) Calculate moment capacity
As fy
a= = 151mm
0.85 f'c bw
ø = 0.900
Mn = As fy (d - a/2) = 315kN·m
øMn = 284kN·m
(6) Calculate ratio of moment capacity
2023-09-15 07:32 2
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 2B1
Mu / øMn = 0.907 → O.K
8. Check Shear Capacity
(1) Calculate shear strength by concrete
ø = 0.750 d = 543mm
øVc = ø 0.17 f'c bw d = 79.24kN
Vu > øVc → Shear reinforcement is required
(2) Calculate required shear strength by shear reinforcement
[Link] = ( Vu - øVc ) / ø = 63.30kN
Vc1 = 0.33 f'c bw d = 205kN Refer to [[Link]]
Vc2 = 0.66 f'c bw d = 410kN
[Link] < Vc2 → O.K
bw bw
Av.min1/s = 0.062 f'c Av.min2/s = 0.35
fyt fyt
[Link] = max [ Av.min1 , Av.min2 ] = 0.385mm²/mm
[Link]
Av.req0 = = 0.514mm²/mm
fyt ㆍ d
[Link] = max [ [Link] , Av.req0 ] = 0.514mm²/mm
(3) Calculate shear strength by stirrup
Nleg = 2 Av1 = 78.60mm² (P10)
Av fyt d
øVs = ø = 145kN
s
(4) Calculate ratio of shear capacity
øVn = øVc + øVs = 224kN
Vu / øVn = 0.565 → O.K
(5) Calculate spacing limits for reinforcement
smax.0 = min [ d/2, 600mm ] = 271mm
Nleg Av1
sreq = = 306mm
[Link]
smax = min [ smax.0 sreq ] = 271mm
s = 100mm < smax = 271mm → O.K
Section : MIDDLE
1. General Information
(1) Design Code : ACI318M-14
(2) Code Unit : N, mm
2. Material
(1) F'c : 21.00MPa
(2) Fy : 275MPa
(3) Fys : 227MPa
3. Section
(1) Section Size : 250 x 625mm (R-Section)
(2) Cover : 40.00mm
(3) Compression : Not Considered
(4) Splicing Limit : 0%
2023-09-15 07:32 3
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 2B1
250
40
625
40
4. Moments and Forces
(1) Mu,top : 9.151kN·m
(2) Mu,bottom : 111kN·m
(3) Vu : 38.02kN
5. Reinforcement
(1) Top Bar : 3-P25 (As = 1,473mm²)
Layer 1 : 3 EA (Cc = 62.50mm)
(2) Bot Bar : 3-P25 (As = 1,473mm²)
Layer 1 : 3 EA (Cc = 62.50mm)
(3) Stirrup : 2-P10@150 (As = 157mm²)
6. Check Bending Moment Capacity (Positive)
(1) Calculate design parameter
β1 = 0.850
(2) Check space of rebar
280 280
smax1 = 380 ( ) - 2.5cc smax2 = 300 ( )
fs fs
smax = min ( smax1 , smax2 ) = 455mm, Nreq =2
s = 62.50 < 455mm → O.K
(3) Calculate required ratio of reinforcement
( f'c )1/2 1.4
ρmin.11 = 0.25 ρmin.12 =
fy fy
ρmin.1 = max ( ρmin.11 , ρmin.12 ) = 0.0051
4 Mu
ρmin.2 = = 0.0079
3 ø fy bd(d-a/2)
ρmin = min ( ρmin1 , ρmin2 ) = 0.0051
f'c εc
ρεt = 0.85 β1 ( )( ) = 0.0236
fy εc + 0.004
ρmax = ρet = 0.0236
(4) Check ratio of tensile reinforcement
As
ρ= = 0.0105
bw d
ρmin < ρ < ρmax → O.K
2023-09-15 07:32 4
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 2B1
(5) Calculate moment capacity
As fy
a= = 90.75mm
0.85 f'c bw
ø = 0.900
Mn = As fy (d - a/2) = 209kN·m
øMn = 188kN·m
(6) Calculate ratio of moment capacity
Mu / øMn = 0.589 → O.K
7. Check Bending Moment Capacity (Negative)
(1) Calculate design parameter
β1 = 0.850
(2) Check space of rebar
280 280
smax1 = 380 ( ) - 2.5cc smax2 = 300 ( )
fs fs
smax = min ( smax1 , smax2 ) = 455mm, Nreq =2
s = 62.50 < 455mm → O.K
(3) Calculate required ratio of reinforcement
( f'c )1/2 1.4
ρmin.11 = 0.25 ρmin.12 =
fy fy
ρmin.1 = max ( ρmin.11 , ρmin.12 ) = 0.0051
4 Mu
ρmin.2 = = 0.0006
3 ø fy bd(d-a/2)
ρmin = min ( ρmin1 , ρmin2 ) = 0.0006
f'c εc
ρεt = 0.85 β1 ( )( ) = 0.0236
fy εc + 0.004
ρmax = ρet = 0.0236
(4) Check ratio of tensile reinforcement
As
ρ= = 0.0105
bw d
ρmin < ρ < ρmax → O.K
(5) Calculate moment capacity
As fy
a= = 90.75mm
0.85 f'c bw
ø = 0.900
Mn = As fy (d - a/2) = 209kN·m
øMn = 188kN·m
(6) Calculate ratio of moment capacity
Mu / øMn = 0.0486 → O.K
8. Check Shear Capacity
(1) Calculate shear strength by concrete
ø = 0.750 d = 563mm
øVc = ø 0.17 f'c bw d = 82.16kN
1
Vu < øVc → Shear reinforcement is not required
2
(2) Calculate shear strength by stirrup
Nleg = 2 Av1 = 78.60mm² (P10)
Av fyt d
øVs = ø = 100kN
s
(3) Calculate ratio of shear capacity
øVn = øVc + øVs = 183kN
Vu / øVn = 0.208 → O.K
(4) Calculate spacing limits for reinforcement
2023-09-15 07:32 5
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 2B1
smax.0 = min [ d/2, 600mm ] = 281mm
Nleg Av1
sreq = = 281mm
[Link]
smax = min [ smax.0 sreq ] = 281mm
s = 150mm < smax = 281mm → O.K
2023-09-15 07:32 6
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 2B2(24)
Section : BOTH END
1. General Information
(1) Design Code : ACI318M-14
(2) Code Unit : N, mm
2. Material
(1) F'c : 21.00MPa
(2) Fy : 420MPa
(3) Fys : 227MPa
3. Section
(1) Section Size : 350 x 500mm (R-Section)
(2) Cover : 40.00mm
(3) Compression : Not Considered
(4) Splicing Limit : 0%
350
40
500
40
4. Moments and Forces
(1) Mu,top : 216kN·m
(2) Mu,bottom : 35.75kN·m
(3) Vu : 108kN
5. Reinforcement
(1) Top Bar : 4-P25 (As = 1,964mm²)
Layer 1 : 4 EA (Cc = 62.50mm)
(2) Bot Bar : 2-P25 (As = 982mm²)
Layer 1 : 2 EA (Cc = 62.50mm)
(3) Stirrup : 2-P10@100 (As = 157mm²)
6. Check Bending Moment Capacity (Positive)
(1) Calculate design parameter
β1 = 0.850
(2) Check space of rebar
280 280
smax1 = 380 ( ) - 2.5cc smax2 = 300 ( )
fs fs
smax = min ( smax1 , smax2 ) = 255mm, Nreq =2
2023-09-15 07:36 1
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 2B2(24)
s = 225 < 255mm → O.K
(3) Calculate required ratio of reinforcement
( f'c )1/2 1.4
ρmin.11 = 0.25 ρmin.12 =
fy fy
ρmin.1 = max ( ρmin.11 , ρmin.12 ) = 0.0033
4 Mu
ρmin.2 = = 0.0019
3 ø fy bd(d-a/2)
ρmin = min ( ρmin1 , ρmin2 ) = 0.0019
f'c εc
ρεt = 0.85 β1 ( )( ) = 0.0155
fy εc + 0.004
ρmax = ρet = 0.0155
(4) Check ratio of tensile reinforcement
As
ρ= = 0.0064
bw d
ρmin < ρ < ρmax → O.K
(5) Calculate moment capacity
As fy
a= = 66.00mm
0.85 f'c bw
ø = 0.900
Mn = As fy (d - a/2) = 167kN·m
øMn = 150kN·m
(6) Calculate ratio of moment capacity
Mu / øMn = 0.238 → O.K
7. Check Bending Moment Capacity (Negative)
(1) Calculate design parameter
β1 = 0.850
(2) Check space of rebar
280 280
smax1 = 380 ( ) - 2.5cc smax2 = 300 ( )
fs fs
smax = min ( smax1 , smax2 ) = 255mm, Nreq =2
s = 75.00 < 255mm → O.K
(3) Calculate required ratio of reinforcement
( f'c )1/2 1.4
ρmin.11 = 0.25 ρmin.12 =
fy fy
ρmin.1 = max ( ρmin.11 , ρmin.12 ) = 0.0033
4 Mu
ρmin.2 = = 0.0128
3 ø fy bd(d-a/2)
ρmin = min ( ρmin1 , ρmin2 ) = 0.0033
f'c εc
ρεt = 0.85 β1 ( )( ) = 0.0155
fy εc + 0.004
ρmax = ρet = 0.0155
(4) Check ratio of tensile reinforcement
As
ρ= = 0.0128
bw d
ρmin < ρ < ρmax → O.K
(5) Calculate moment capacity
As fy
a= = 132mm
0.85 f'c bw
ø = 0.900
Mn = As fy (d - a/2) = 306kN·m
øMn = 276kN·m
(6) Calculate ratio of moment capacity
Mu / øMn = 0.783 → O.K
2023-09-15 07:36 2
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 2B2(24)
8. Check Shear Capacity
(1) Calculate shear strength by concrete
ø = 0.750 d = 438mm
øVc = ø 0.17 f'c bw d = 89.47kN
Vu > øVc → Shear reinforcement is required
(2) Calculate required shear strength by shear reinforcement
[Link] = ( Vu - øVc ) / ø = 24.12kN
Vc1 = 0.33 f'c bw d = 232kN Refer to [[Link]]
Vc2 = 0.66 f'c bw d = 463kN
[Link] < Vc2 → O.K
bw bw
Av.min1/s = 0.062 f'c Av.min2/s = 0.35
fyt fyt
[Link] = max [ Av.min1 , Av.min2 ] = 0.540mm²/mm
[Link]
Av.req0 = = 0.243mm²/mm
fyt ㆍ d
[Link] = max [ [Link] , Av.req0 ] = 0.540mm²/mm
(3) Calculate shear strength by stirrup
Nleg = 2 Av1 = 78.60mm² (P10)
Av fyt d
øVs = ø = 117kN
s
(4) Calculate ratio of shear capacity
øVn = øVc + øVs = 207kN
Vu / øVn = 0.521 → O.K
(5) Calculate spacing limits for reinforcement
smax.0 = min [ d/2, 600mm ] = 219mm
Nleg Av1
sreq = = 291mm
[Link]
smax = min [ smax.0 sreq ] = 219mm
s = 100mm < smax = 219mm → O.K
Section : MIDDLE
1. General Information
(1) Design Code : ACI318M-14
(2) Code Unit : N, mm
2. Material
(1) F'c : 21.00MPa
(2) Fy : 420MPa
(3) Fys : 227MPa
3. Section
(1) Section Size : 350 x 500mm (R-Section)
(2) Cover : 40.00mm
(3) Compression : Not Considered
(4) Splicing Limit : 0%
2023-09-15 07:36 3
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 2B2(24)
350
40
500
40
4. Moments and Forces
(1) Mu,top : 86.34kN·m
(2) Mu,bottom : 65.90kN·m
(3) Vu : 91.18kN
5. Reinforcement
(1) Top Bar : 4-P25 (As = 1,964mm²)
Layer 1 : 4 EA (Cc = 62.50mm)
(2) Bot Bar : 2-P25 (As = 982mm²)
Layer 1 : 2 EA (Cc = 62.50mm)
(3) Stirrup : 2-P10@150 (As = 157mm²)
6. Check Bending Moment Capacity (Positive)
(1) Calculate design parameter
β1 = 0.850
(2) Check space of rebar
280 280
smax1 = 380 ( ) - 2.5cc smax2 = 300 ( )
fs fs
smax = min ( smax1 , smax2 ) = 255mm, Nreq =2
s = 225 < 255mm → O.K
(3) Calculate required ratio of reinforcement
( f'c )1/2 1.4
ρmin.11 = 0.25 ρmin.12 =
fy fy
ρmin.1 = max ( ρmin.11 , ρmin.12 ) = 0.0033
4 Mu
ρmin.2 = = 0.0036
3 ø fy bd(d-a/2)
ρmin = min ( ρmin1 , ρmin2 ) = 0.0033
f'c εc
ρεt = 0.85 β1 ( )( ) = 0.0155
fy εc + 0.004
ρmax = ρet = 0.0155
(4) Check ratio of tensile reinforcement
As
ρ= = 0.0064
bw d
ρmin < ρ < ρmax → O.K
2023-09-15 07:36 4
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 2B2(24)
(5) Calculate moment capacity
As fy
a= = 66.00mm
0.85 f'c bw
ø = 0.900
Mn = As fy (d - a/2) = 167kN·m
øMn = 150kN·m
(6) Calculate ratio of moment capacity
Mu / øMn = 0.439 → O.K
7. Check Bending Moment Capacity (Negative)
(1) Calculate design parameter
β1 = 0.850
(2) Check space of rebar
280 280
smax1 = 380 ( ) - 2.5cc smax2 = 300 ( )
fs fs
smax = min ( smax1 , smax2 ) = 255mm, Nreq =2
s = 75.00 < 255mm → O.K
(3) Calculate required ratio of reinforcement
( f'c )1/2 1.4
ρmin.11 = 0.25 ρmin.12 =
fy fy
ρmin.1 = max ( ρmin.11 , ρmin.12 ) = 0.0033
4 Mu
ρmin.2 = = 0.0047
3 ø fy bd(d-a/2)
ρmin = min ( ρmin1 , ρmin2 ) = 0.0033
f'c εc
ρεt = 0.85 β1 ( )( ) = 0.0155
fy εc + 0.004
ρmax = ρet = 0.0155
(4) Check ratio of tensile reinforcement
As
ρ= = 0.0128
bw d
ρmin < ρ < ρmax → O.K
(5) Calculate moment capacity
As fy
a= = 132mm
0.85 f'c bw
ø = 0.900
Mn = As fy (d - a/2) = 306kN·m
øMn = 276kN·m
(6) Calculate ratio of moment capacity
Mu / øMn = 0.313 → O.K
8. Check Shear Capacity
(1) Calculate shear strength by concrete
ø = 0.750 d = 438mm
øVc = ø 0.17 f'c bw d = 89.47kN
Vu > øVc → Shear reinforcement is required
(2) Calculate required shear strength by shear reinforcement
[Link] = ( Vu - øVc ) / ø = 2.288kN
Vc1 = 0.33 f'c bw d = 232kN Refer to [[Link]]
Vc2 = 0.66 f'c bw d = 463kN
[Link] < Vc2 → O.K
bw bw
Av.min1/s = 0.062 f'c Av.min2/s = 0.35
fyt fyt
[Link] = max [ Av.min1 , Av.min2 ] = 0.540mm²/mm
2023-09-15 07:36 5
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 2B2(24)
[Link]
Av.req0 = = 0.0230mm²/mm
fyt ㆍ d
[Link] = max [ [Link] , Av.req0 ] = 0.540mm²/mm
(3) Calculate shear strength by stirrup
Nleg = 2 Av1 = 78.60mm² (P10)
Av fyt d
øVs = ø = 78.06kN
s
(4) Calculate ratio of shear capacity
øVn = øVc + øVs = 168kN
Vu / øVn = 0.544 → O.K
(5) Calculate spacing limits for reinforcement
smax.0 = min [ d/2, 600mm ] = 219mm
Nleg Av1
sreq = = 291mm
[Link]
smax = min [ smax.0 sreq ] = 219mm
s = 150mm < smax = 219mm → O.K
2023-09-15 07:36 6
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 2B1(21)
Section : BOTH END
1. General Information
(1) Design Code : ACI318M-14
(2) Code Unit : N, mm
2. Material
(1) F'c : 21.00MPa
(2) Fy : 420MPa
(3) Fys : 227MPa
3. Section
(1) Section Size : 300 x 450mm (R-Section)
(2) Cover : 40.00mm
(3) Compression : Not Considered
(4) Splicing Limit : 0%
300
40
450
40
4. Moments and Forces
(1) Mu,top : 182kN·m
(2) Mu,bottom : 34.33kN·m
(3) Vu : 98.66kN
5. Reinforcement
(1) Top Bar : 5-P20 (As = 1,571mm²)
Layer 1 : 3 EA (Cc = 60.00mm)
Layer 2 : 2 EA (Cc = 105mm)
(2) Bot Bar : 3-P20 (As = 943mm²)
Layer 1 : 3 EA (Cc = 60.00mm)
(3) Stirrup : 2-P10@100 (As = 157mm²)
6. Check Bending Moment Capacity (Positive)
(1) Calculate design parameter
β1 = 0.850
(2) Check space of rebar
280 280
smax1 = 380 ( ) - 2.5cc smax2 = 300 ( )
fs fs
2023-09-15 07:37 1
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 2B1(21)
smax = min ( smax1 , smax2 ) = 255mm, Nreq = 2
s = 90.00 < 255mm → O.K
(3) Calculate required ratio of reinforcement
( f'c )1/2 1.4
ρmin.11 = 0.25 ρmin.12 =
fy fy
ρmin.1 = max ( ρmin.11 , ρmin.12 ) = 0.0033
4 Mu
ρmin.2 = = 0.0027
3 ø fy bd(d-a/2)
ρmin = min ( ρmin1 , ρmin2 ) = 0.0027
f'c εc
ρεt = 0.85 β1 ( )( ) = 0.0155
fy εc + 0.004
ρmax = ρet = 0.0155
(4) Check ratio of tensile reinforcement
As
ρ= = 0.0081
bw d
ρmin < ρ < ρmax → O.K
(5) Calculate moment capacity
As fy
a= = 73.93mm
0.85 f'c bw
ø = 0.900
Mn = As fy (d - a/2) = 140kN·m
øMn = 126kN·m
(6) Calculate ratio of moment capacity
Mu / øMn = 0.273 → O.K
7. Check Bending Moment Capacity (Negative)
(1) Calculate design parameter
β1 = 0.850
(2) Check space of rebar
280 280
smax1 = 380 ( ) - 2.5cc smax2 = 300 ( )
fs fs
smax = min ( smax1 , smax2 ) = 255mm, Nreq =2
s = 90.00 < 255mm → O.K
(3) Calculate required ratio of reinforcement
1/2
( f'c ) 1.4
ρmin.11 = 0.25 ρmin.12 =
fy fy
ρmin.1 = max ( ρmin.11 , ρmin.12 ) = 0.0033
4 Mu
ρmin.2 = = 0.0184
3 ø fy bd(d-a/2)
ρmin = min ( ρmin1 , ρmin2 ) = 0.0033
f'c εc
ρεt = 0.85 β1 ( )( ) = 0.0155
fy εc + 0.004
ρmax = ρet = 0.0155
(4) Check ratio of tensile reinforcement
As
ρ= = 0.0141
bw d
ρmin < ρ < ρmax → O.K
(5) Calculate moment capacity
As fy
a= = 123mm
0.85 f'c bw
ø = 0.900
Mn = As fy (d - a/2) = 205kN·m
øMn = 184kN·m
(6) Calculate ratio of moment capacity
2023-09-15 07:37 2
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 2B1(21)
Mu / øMn = 0.986 → O.K
8. Check Shear Capacity
(1) Calculate shear strength by concrete
ø = 0.750 d = 372mm
øVc = ø 0.17 f'c bw d = 65.21kN
Vu > øVc → Shear reinforcement is required
(2) Calculate required shear strength by shear reinforcement
[Link] = ( Vu - øVc ) / ø = 44.60kN
Vc1 = 0.33 f'c bw d = 169kN Refer to [[Link]]
Vc2 = 0.66 f'c bw d = 338kN
[Link] < Vc2 → O.K
bw bw
Av.min1/s = 0.062 f'c Av.min2/s = 0.35
fyt fyt
[Link] = max [ Av.min1 , Av.min2 ] = 0.463mm²/mm
[Link]
Av.req0 = = 0.528mm²/mm
fyt ㆍ d
[Link] = max [ [Link] , Av.req0 ] = 0.528mm²/mm
(3) Calculate shear strength by stirrup
Nleg = 2 Av1 = 78.60mm² (P10)
Av fyt d
øVs = ø = 99.56kN
s
(4) Calculate ratio of shear capacity
øVn = øVc + øVs = 165kN
Vu / øVn = 0.599 → O.K
(5) Calculate spacing limits for reinforcement
smax.0 = min [ d/2, 600mm ] = 186mm
Nleg Av1
sreq = = 298mm
[Link]
smax = min [ smax.0 sreq ] = 186mm
s = 100mm < smax = 186mm → O.K
Section : MIDDLE
1. General Information
(1) Design Code : ACI318M-14
(2) Code Unit : N, mm
2. Material
(1) F'c : 21.00MPa
(2) Fy : 420MPa
(3) Fys : 227MPa
3. Section
(1) Section Size : 300 x 450mm (R-Section)
(2) Cover : 40.00mm
(3) Compression : Not Considered
(4) Splicing Limit : 0%
2023-09-15 07:37 3
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 2B1(21)
300
40
450
40
4. Moments and Forces
(1) Mu,top : 67.07kN·m
(2) Mu,bottom : 68.81kN·m
(3) Vu : 79.53kN
5. Reinforcement
(1) Top Bar : 3-P20 (As = 943mm²)
Layer 1 : 3 EA (Cc = 60.00mm)
(2) Bot Bar : 3-P20 (As = 943mm²)
Layer 1 : 3 EA (Cc = 60.00mm)
(3) Stirrup : 2-P10@150 (As = 157mm²)
6. Check Bending Moment Capacity (Positive)
(1) Calculate design parameter
β1 = 0.850
(2) Check space of rebar
280 280
smax1 = 380 ( ) - 2.5cc smax2 = 300 ( )
fs fs
smax = min ( smax1 , smax2 ) = 255mm, Nreq =2
s = 90.00 < 255mm → O.K
(3) Calculate required ratio of reinforcement
( f'c )1/2 1.4
ρmin.11 = 0.25 ρmin.12 =
fy fy
ρmin.1 = max ( ρmin.11 , ρmin.12 ) = 0.0033
4 Mu
ρmin.2 = = 0.0056
3 ø fy bd(d-a/2)
ρmin = min ( ρmin1 , ρmin2 ) = 0.0033
f'c εc
ρεt = 0.85 β1 ( )( ) = 0.0155
fy εc + 0.004
ρmax = ρet = 0.0155
(4) Check ratio of tensile reinforcement
As
ρ= = 0.0081
bw d
ρmin < ρ < ρmax → O.K
2023-09-15 07:37 4
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 2B1(21)
(5) Calculate moment capacity
As fy
a= = 73.93mm
0.85 f'c bw
ø = 0.900
Mn = As fy (d - a/2) = 140kN·m
øMn = 126kN·m
(6) Calculate ratio of moment capacity
Mu / øMn = 0.547 → O.K
7. Check Bending Moment Capacity (Negative)
(1) Calculate design parameter
β1 = 0.850
(2) Check space of rebar
280 280
smax1 = 380 ( ) - 2.5cc smax2 = 300 ( )
fs fs
smax = min ( smax1 , smax2 ) = 255mm, Nreq =2
s = 90.00 < 255mm → O.K
(3) Calculate required ratio of reinforcement
( f'c )1/2 1.4
ρmin.11 = 0.25 ρmin.12 =
fy fy
ρmin.1 = max ( ρmin.11 , ρmin.12 ) = 0.0033
4 Mu
ρmin.2 = = 0.0054
3 ø fy bd(d-a/2)
ρmin = min ( ρmin1 , ρmin2 ) = 0.0033
f'c εc
ρεt = 0.85 β1 ( )( ) = 0.0155
fy εc + 0.004
ρmax = ρet = 0.0155
(4) Check ratio of tensile reinforcement
As
ρ= = 0.0081
bw d
ρmin < ρ < ρmax → O.K
(5) Calculate moment capacity
As fy
a= = 73.93mm
0.85 f'c bw
ø = 0.900
Mn = As fy (d - a/2) = 140kN·m
øMn = 126kN·m
(6) Calculate ratio of moment capacity
Mu / øMn = 0.533 → O.K
8. Check Shear Capacity
(1) Calculate shear strength by concrete
ø = 0.750 d = 390mm
øVc = ø 0.17 f'c bw d = 68.36kN
Vu > øVc → Shear reinforcement is required
(2) Calculate required shear strength by shear reinforcement
[Link] = ( Vu - øVc ) / ø = 14.89kN
Vc1 = 0.33 f'c bw d = 177kN Refer to [[Link]]
Vc2 = 0.66 f'c bw d = 354kN
[Link] < Vc2 → O.K
bw bw
Av.min1/s = 0.062 f'c Av.min2/s = 0.35
fyt fyt
[Link] = max [ Av.min1 , Av.min2 ] = 0.463mm²/mm
2023-09-15 07:37 5
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 2B1(21)
[Link]
Av.req0 = = 0.168mm²/mm
fyt ㆍ d
[Link] = max [ [Link] , Av.req0 ] = 0.463mm²/mm
(3) Calculate shear strength by stirrup
Nleg = 2 Av1 = 78.60mm² (P10)
Av fyt d
øVs = ø = 69.58kN
s
(4) Calculate ratio of shear capacity
øVn = øVc + øVs = 138kN
Vu / øVn = 0.577 → O.K
(5) Calculate spacing limits for reinforcement
smax.0 = min [ d/2, 600mm ] = 195mm
Nleg Av1
sreq = = 340mm
[Link]
smax = min [ smax.0 sreq ] = 195mm
s = 150mm < smax = 195mm → O.K
2023-09-15 07:37 6
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 22FCB1 (23)
Section : BOTH END
1. General Information
(1) Design Code : ACI318M-14
(2) Code Unit : N, mm
2. Material
(1) F'c : 21.00MPa
(2) Fy : 420MPa
(3) Fys : 227MPa
3. Section
(1) Section Size : 400 x 575mm (R-Section)
(2) Cover : 40.00mm
(3) Compression : Not Considered
(4) Splicing Limit : 0%
400
40
575
40
4. Moments and Forces
(1) Mu,top : 371kN·m
(2) Mu,bottom : 0.000kN·m
(3) Vu : 141kN
5. Reinforcement
(1) Top Bar : 5-P25 (As = 2,455mm²)
Layer 1 : 5 EA (Cc = 62.50mm)
(2) Bot Bar : 2-P25 (As = 982mm²)
Layer 1 : 2 EA (Cc = 62.50mm)
(3) Stirrup : 2-P10@100 (As = 157mm²)
6. Check Bending Moment Capacity (Positive)
(1) Calculate design parameter
β1 = 0.850
(2) Check space of rebar
Moment is zero. Skipped.
(3) Calculate required ratio of reinforcement
Moment is zero. Skipped.
2023-09-15 07:39 1
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 22FCB1 (23)
(4) Calculate moment capacity
Moment is zero. Skipped.
7. Check Bending Moment Capacity (Negative)
(1) Calculate design parameter
β1 = 0.850
(2) Check space of rebar
280 280
smax1 = 380 ( ) - 2.5cc smax2 = 300 ( )
fs fs
smax = min ( smax1 , smax2 ) = 255mm, Nreq =3
s = 68.75 < 255mm → O.K
(3) Calculate required ratio of reinforcement
1/2
( f'c ) 1.4
ρmin.11 = 0.25 ρmin.12 =
fy fy
ρmin.1 = max ( ρmin.11 , ρmin.12 ) = 0.0033
4 Mu
ρmin.2 = = 0.0142
3 ø fy bd(d-a/2)
ρmin = min ( ρmin1 , ρmin2 ) = 0.0033
f'c εc
ρεt = 0.85 β1 ( )( ) = 0.0155
fy εc + 0.004
ρmax = ρet = 0.0155
(4) Check ratio of tensile reinforcement
As
ρ= = 0.0120
bw d
ρmin < ρ < ρmax → O.K
(5) Calculate moment capacity
As fy
a= = 144mm
0.85 f'c bw
ø = 0.900
Mn = As fy (d - a/2) = 454kN·m
øMn = 409kN·m
(6) Calculate ratio of moment capacity
Mu / øMn = 0.908 → O.K
8. Check Shear Capacity
(1) Calculate shear strength by concrete
ø = 0.750 d = 513mm
øVc = ø 0.17 f'c bw d = 120kN
Vu > øVc → Shear reinforcement is required
(2) Calculate required shear strength by shear reinforcement
[Link] = ( Vu - øVc ) / ø = 28.60kN
Vc1 = 0.33 f'c bw d = 310kN Refer to [[Link]]
Vc2 = 0.66 f'c bw d = 620kN
[Link] < Vc2 → O.K
bw bw
Av.min1/s = 0.062 f'c Av.min2/s = 0.35
fyt fyt
[Link] = max [ Av.min1 , Av.min2 ] = 0.617mm²/mm
[Link]
Av.req0 = = 0.246mm²/mm
fyt ㆍ d
[Link] = max [ [Link] , Av.req0 ] = 0.617mm²/mm
(3) Calculate shear strength by stirrup
Nleg = 2 Av1 = 78.60mm² (P10)
Av fyt d
øVs = ø = 137kN
s
2023-09-15 07:39 2
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 22FCB1 (23)
(4) Calculate ratio of shear capacity
øVn = øVc + øVs = 257kN
Vu / øVn = 0.550 → O.K
(5) Calculate spacing limits for reinforcement
smax.0 = min [ d/2, 600mm ] = 256mm
Nleg Av1
sreq = = 255mm
[Link]
smax = min [ smax.0 sreq ] = 255mm
s = 100mm < smax = 255mm → O.K
Section : MIDDLE
1. General Information
(1) Design Code : ACI318M-14
(2) Code Unit : N, mm
2. Material
(1) F'c : 21.00MPa
(2) Fy : 420MPa
(3) Fys : 227MPa
3. Section
(1) Section Size : 400 x 575mm (R-Section)
(2) Cover : 40.00mm
(3) Compression : Not Considered
(4) Splicing Limit : 0%
400
40
575
40
4. Moments and Forces
(1) Mu,top : 251kN·m
(2) Mu,bottom : 0.000kN·m
2023-09-15 07:39 3
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 22FCB1 (23)
(3) Vu : 130kN
5. Reinforcement
(1) Top Bar : 4-P25 (As = 1,964mm²)
Layer 1 : 4 EA (Cc = 62.50mm)
(2) Bot Bar : 2-P25 (As = 982mm²)
Layer 1 : 2 EA (Cc = 62.50mm)
(3) Stirrup : 2-P10@150 (As = 157mm²)
6. Check Bending Moment Capacity (Positive)
(1) Calculate design parameter
β1 = 0.850
(2) Check space of rebar
Moment is zero. Skipped.
(3) Calculate required ratio of reinforcement
Moment is zero. Skipped.
(4) Calculate moment capacity
Moment is zero. Skipped.
7. Check Bending Moment Capacity (Negative)
(1) Calculate design parameter
β1 = 0.850
(2) Check space of rebar
280 280
smax1 = 380 ( ) - 2.5cc smax2 = 300 ( )
fs fs
smax = min ( smax1 , smax2 ) = 255mm, Nreq =3
s = 91.67 < 255mm → O.K
(3) Calculate required ratio of reinforcement
1/2
( f'c ) 1.4
ρmin.11 = 0.25 ρmin.12 =
fy fy
ρmin.1 = max ( ρmin.11 , ρmin.12 ) = 0.0033
4 Mu
ρmin.2 = = 0.0092
3 ø fy bd(d-a/2)
ρmin = min ( ρmin1 , ρmin2 ) = 0.0033
f'c εc
ρεt = 0.85 β1 ( )( ) = 0.0155
fy εc + 0.004
ρmax = ρet = 0.0155
(4) Check ratio of tensile reinforcement
As
ρ= = 0.0096
bw d
ρmin < ρ < ρmax → O.K
(5) Calculate moment capacity
As fy
a= = 116mm
0.85 f'c bw
ø = 0.900
Mn = As fy (d - a/2) = 375kN·m
øMn = 338kN·m
(6) Calculate ratio of moment capacity
Mu / øMn = 0.744 → O.K
8. Check Shear Capacity
(1) Calculate shear strength by concrete
ø = 0.750 d = 513mm
øVc = ø 0.17 f'c bw d = 120kN
2023-09-15 07:39 4
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 22FCB1 (23)
Vu > øVc → Shear reinforcement is required
(2) Calculate required shear strength by shear reinforcement
[Link] = ( Vu - øVc ) / ø = 13.95kN
Vc1 = 0.33 f'c bw d = 310kN Refer to [[Link]]
Vc2 = 0.66 f'c bw d = 620kN
[Link] < Vc2 → O.K
bw bw
Av.min1/s = 0.062 f'c Av.min2/s = 0.35
fyt fyt
[Link] = max [ Av.min1 , Av.min2 ] = 0.617mm²/mm
[Link]
Av.req0 = = 0.120mm²/mm
fyt ㆍ d
[Link] = max [ [Link] , Av.req0 ] = 0.617mm²/mm
(3) Calculate shear strength by stirrup
Nleg = 2 Av1 = 78.60mm² (P10)
Av fyt d
øVs = ø = 91.44kN
s
(4) Calculate ratio of shear capacity
øVn = øVc + øVs = 211kN
Vu / øVn = 0.617 → O.K
(5) Calculate spacing limits for reinforcement
smax.0 = min [ d/2, 600mm ] = 256mm
Nleg Av1
sreq = = 255mm
[Link]
smax = min [ smax.0 sreq ] = 255mm
s = 150mm < smax = 255mm → O.K
2023-09-15 07:39 5
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 3B1(44)
Section : BOTH END
1. General Information
(1) Design Code : ACI318M-14
(2) Code Unit : N, mm
2. Material
(1) F'c : 21.00MPa
(2) Fy : 420MPa
(3) Fys : 227MPa
3. Section
(1) Section Size : 250 x 550mm (R-Section)
(2) Cover : 40.00mm
(3) Compression : Not Considered
(4) Splicing Limit : 0%
250
40
550
40
4. Moments and Forces
(1) Mu,top : 93.17kN·m
(2) Mu,bottom : 25.55kN·m
(3) Vu : 54.32kN
5. Reinforcement
(1) Top Bar : 2-P20 (As = 628mm²)
Layer 1 : 2 EA (Cc = 60.00mm)
(2) Bot Bar : 2-P20 (As = 628mm²)
Layer 1 : 2 EA (Cc = 60.00mm)
(3) Stirrup : 2-P10@100 (As = 157mm²)
6. Check Bending Moment Capacity (Positive)
(1) Calculate design parameter
β1 = 0.850
(2) Check space of rebar
280 280
smax1 = 380 ( ) - 2.5cc smax2 = 300 ( )
fs fs
smax = min ( smax1 , smax2 ) = 255mm, Nreq =2
2023-09-15 07:41 1
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 3B1(44)
s = 130 < 255mm → O.K
(3) Calculate required ratio of reinforcement
( f'c )1/2 1.4
ρmin.11 = 0.25 ρmin.12 =
fy fy
ρmin.1 = max ( ρmin.11 , ρmin.12 ) = 0.0033
4 Mu
ρmin.2 = = 0.0015
3 ø fy bd(d-a/2)
ρmin = min ( ρmin1 , ρmin2 ) = 0.0015
f'c εc
ρεt = 0.85 β1 ( )( ) = 0.0155
fy εc + 0.004
ρmax = ρet = 0.0155
(4) Check ratio of tensile reinforcement
As
ρ= = 0.0051
bw d
ρmin < ρ < ρmax → O.K
(5) Calculate moment capacity
As fy
a= = 59.14mm
0.85 f'c bw
ø = 0.900
Mn = As fy (d - a/2) = 122kN·m
øMn = 109kN·m
(6) Calculate ratio of moment capacity
Mu / øMn = 0.234 → O.K
7. Check Bending Moment Capacity (Negative)
(1) Calculate design parameter
β1 = 0.850
(2) Check space of rebar
280 280
smax1 = 380 ( ) - 2.5cc smax2 = 300 ( )
fs fs
smax = min ( smax1 , smax2 ) = 255mm, Nreq =2
s = 130 < 255mm → O.K
(3) Calculate required ratio of reinforcement
( f'c )1/2 1.4
ρmin.11 = 0.25 ρmin.12 =
fy fy
ρmin.1 = max ( ρmin.11 , ρmin.12 ) = 0.0033
4 Mu
ρmin.2 = = 0.0058
3 ø fy bd(d-a/2)
ρmin = min ( ρmin1 , ρmin2 ) = 0.0033
f'c εc
ρεt = 0.85 β1 ( )( ) = 0.0155
fy εc + 0.004
ρmax = ρet = 0.0155
(4) Check ratio of tensile reinforcement
As
ρ= = 0.0051
bw d
ρmin < ρ < ρmax → O.K
(5) Calculate moment capacity
As fy
a= = 59.14mm
0.85 f'c bw
ø = 0.900
Mn = As fy (d - a/2) = 122kN·m
øMn = 109kN·m
(6) Calculate ratio of moment capacity
Mu / øMn = 0.852 → O.K
2023-09-15 07:41 2
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 3B1(44)
8. Check Shear Capacity
(1) Calculate shear strength by concrete
ø = 0.750 d = 490mm
øVc = ø 0.17 f'c bw d = 71.57kN
1
øVc < Vu < øVc → Minimum shear reinforcement is required
2
(2) Calculate required shear strength by shear reinforcement
bw bw
Av.min1/s = 0.062 f'c Av.min2/s = 0.35
fyt fyt
[Link] = max [ Av.min1 , Av.min2 ] = 0.385mm²/mm
Av,req = [Link] = 0.385mm²/mm
(3) Calculate shear strength by stirrup
Nleg = 2 Av1 = 78.60mm² (P10)
Av fyt d
øVs = ø = 131kN
s
(4) Calculate ratio of shear capacity
øVn = øVc + øVs = 203kN
Vu / øVn = 0.268 → O.K
(5) Calculate spacing limits for reinforcement
smax.0 = min [ d/2, 600mm ] = 245mm
Nleg Av1
sreq = = 408mm
[Link]
smax = min [ smax.0 sreq ] = 245mm
s = 100mm < smax = 245mm → O.K
Section : MIDDLE
1. General Information
(1) Design Code : ACI318M-14
(2) Code Unit : N, mm
2. Material
(1) F'c : 21.00MPa
(2) Fy : 420MPa
(3) Fys : 227MPa
3. Section
(1) Section Size : 250 x 550mm (R-Section)
(2) Cover : 40.00mm
(3) Compression : Not Considered
(4) Splicing Limit : 0%
2023-09-15 07:41 3
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 3B1(44)
250
40
550
40
4. Moments and Forces
(1) Mu,top : 61.55kN·m
(2) Mu,bottom : 35.77kN·m
(3) Vu : 47.53kN
5. Reinforcement
(1) Top Bar : 2-P20 (As = 628mm²)
Layer 1 : 2 EA (Cc = 60.00mm)
(2) Bot Bar : 2-P20 (As = 628mm²)
Layer 1 : 2 EA (Cc = 60.00mm)
(3) Stirrup : 2-P10@150 (As = 157mm²)
6. Check Bending Moment Capacity (Positive)
(1) Calculate design parameter
β1 = 0.850
(2) Check space of rebar
280 280
smax1 = 380 ( ) - 2.5cc smax2 = 300 ( )
fs fs
smax = min ( smax1 , smax2 ) = 255mm, Nreq =2
s = 130 < 255mm → O.K
(3) Calculate required ratio of reinforcement
( f'c )1/2 1.4
ρmin.11 = 0.25 ρmin.12 =
fy fy
ρmin.1 = max ( ρmin.11 , ρmin.12 ) = 0.0033
4 Mu
ρmin.2 = = 0.0021
3 ø fy bd(d-a/2)
ρmin = min ( ρmin1 , ρmin2 ) = 0.0021
f'c εc
ρεt = 0.85 β1 ( )( ) = 0.0155
fy εc + 0.004
ρmax = ρet = 0.0155
(4) Check ratio of tensile reinforcement
As
ρ= = 0.0051
bw d
ρmin < ρ < ρmax → O.K
2023-09-15 07:41 4
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 3B1(44)
(5) Calculate moment capacity
As fy
a= = 59.14mm
0.85 f'c bw
ø = 0.900
Mn = As fy (d - a/2) = 122kN·m
øMn = 109kN·m
(6) Calculate ratio of moment capacity
Mu / øMn = 0.327 → O.K
7. Check Bending Moment Capacity (Negative)
(1) Calculate design parameter
β1 = 0.850
(2) Check space of rebar
280 280
smax1 = 380 ( ) - 2.5cc smax2 = 300 ( )
fs fs
smax = min ( smax1 , smax2 ) = 255mm, Nreq =2
s = 130 < 255mm → O.K
(3) Calculate required ratio of reinforcement
( f'c )1/2 1.4
ρmin.11 = 0.25 ρmin.12 =
fy fy
ρmin.1 = max ( ρmin.11 , ρmin.12 ) = 0.0033
4 Mu
ρmin.2 = = 0.0037
3 ø fy bd(d-a/2)
ρmin = min ( ρmin1 , ρmin2 ) = 0.0033
f'c εc
ρεt = 0.85 β1 ( )( ) = 0.0155
fy εc + 0.004
ρmax = ρet = 0.0155
(4) Check ratio of tensile reinforcement
As
ρ= = 0.0051
bw d
ρmin < ρ < ρmax → O.K
(5) Calculate moment capacity
As fy
a= = 59.14mm
0.85 f'c bw
ø = 0.900
Mn = As fy (d - a/2) = 122kN·m
øMn = 109kN·m
(6) Calculate ratio of moment capacity
Mu / øMn = 0.563 → O.K
8. Check Shear Capacity
(1) Calculate shear strength by concrete
ø = 0.750 d = 490mm
øVc = ø 0.17 f'c bw d = 71.57kN
1
øVc < Vu < øVc → Minimum shear reinforcement is required
2
(2) Calculate required shear strength by shear reinforcement
bw bw
Av.min1/s = 0.062 f'c Av.min2/s = 0.35
fyt fyt
[Link] = max [ Av.min1 , Av.min2 ] = 0.385mm²/mm
Av,req = [Link] = 0.385mm²/mm
(3) Calculate shear strength by stirrup
Nleg = 2 Av1 = 78.60mm² (P10)
2023-09-15 07:42 5
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 3B1(44)
Av fyt d
øVs = ø = 87.43kN
s
(4) Calculate ratio of shear capacity
øVn = øVc + øVs = 159kN
Vu / øVn = 0.299 → O.K
(5) Calculate spacing limits for reinforcement
smax.0 = min [ d/2, 600mm ] = 245mm
Nleg Av1
sreq = = 408mm
[Link]
smax = min [ smax.0 sreq ] = 245mm
s = 150mm < smax = 245mm → O.K
2023-09-15 07:42 6
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 43B3(100)
Section : BOTH END
1. General Information
(1) Design Code : ACI318M-14
(2) Code Unit : N, mm
2. Material
(1) F'c : 21.00MPa
(2) Fy : 420MPa
(3) Fys : 227MPa
3. Section
(1) Section Size : 250 x 375mm (R-Section)
(2) Cover : 40.00mm
(3) Compression : Not Considered
(4) Splicing Limit : 0%
250
40
375
40
4. Moments and Forces
(1) Mu,top : 61.16kN·m
(2) Mu,bottom : 30.58kN·m
(3) Vu : 80.48kN
5. Reinforcement
(1) Top Bar : 2-P20 (As = 628mm²)
Layer 1 : 2 EA (Cc = 60.00mm)
(2) Bot Bar : 2-P20 (As = 628mm²)
Layer 1 : 2 EA (Cc = 60.00mm)
(3) Stirrup : 2-P10@80.00 (As = 157mm²)
6. Check Bending Moment Capacity (Positive)
(1) Calculate design parameter
β1 = 0.850
(2) Check space of rebar
280 280
smax1 = 380 ( ) - 2.5cc smax2 = 300 ( )
fs fs
smax = min ( smax1 , smax2 ) = 255mm, Nreq =2
2023-09-15 07:42 1
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 43B3(100)
s = 130 < 255mm → O.K
(3) Calculate required ratio of reinforcement
( f'c )1/2 1.4
ρmin.11 = 0.25 ρmin.12 =
fy fy
ρmin.1 = max ( ρmin.11 , ρmin.12 ) = 0.0033
4 Mu
ρmin.2 = = 0.0045
3 ø fy bd(d-a/2)
ρmin = min ( ρmin1 , ρmin2 ) = 0.0033
f'c εc
ρεt = 0.85 β1 ( )( ) = 0.0155
fy εc + 0.004
ρmax = ρet = 0.0155
(4) Check ratio of tensile reinforcement
As
ρ= = 0.0080
bw d
ρmin < ρ < ρmax → O.K
(5) Calculate moment capacity
As fy
a= = 59.14mm
0.85 f'c bw
ø = 0.900
Mn = As fy (d - a/2) = 75.33kN·m
øMn = 67.80kN·m
(6) Calculate ratio of moment capacity
Mu / øMn = 0.451 → O.K
7. Check Bending Moment Capacity (Negative)
(1) Calculate design parameter
β1 = 0.850
(2) Check space of rebar
280 280
smax1 = 380 ( ) - 2.5cc smax2 = 300 ( )
fs fs
smax = min ( smax1 , smax2 ) = 255mm, Nreq =2
s = 130 < 255mm → O.K
(3) Calculate required ratio of reinforcement
( f'c )1/2 1.4
ρmin.11 = 0.25 ρmin.12 =
fy fy
ρmin.1 = max ( ρmin.11 , ρmin.12 ) = 0.0033
4 Mu
ρmin.2 = = 0.0095
3 ø fy bd(d-a/2)
ρmin = min ( ρmin1 , ρmin2 ) = 0.0033
f'c εc
ρεt = 0.85 β1 ( )( ) = 0.0155
fy εc + 0.004
ρmax = ρet = 0.0155
(4) Check ratio of tensile reinforcement
As
ρ= = 0.0080
bw d
ρmin < ρ < ρmax → O.K
(5) Calculate moment capacity
As fy
a= = 59.14mm
0.85 f'c bw
ø = 0.900
Mn = As fy (d - a/2) = 75.33kN·m
øMn = 67.80kN·m
(6) Calculate ratio of moment capacity
Mu / øMn = 0.902 → O.K
2023-09-15 07:42 2
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 43B3(100)
8. Check Shear Capacity
(1) Calculate shear strength by concrete
ø = 0.750 d = 315mm
øVc = ø 0.17 f'c bw d = 46.01kN
Vu > øVc → Shear reinforcement is required
(2) Calculate required shear strength by shear reinforcement
[Link] = ( Vu - øVc ) / ø = 45.96kN
Vc1 = 0.33 f'c bw d = 119kN Refer to [[Link]]
Vc2 = 0.66 f'c bw d = 238kN
[Link] < Vc2 → O.K
bw bw
Av.min1/s = 0.062 f'c Av.min2/s = 0.35
fyt fyt
[Link] = max [ Av.min1 , Av.min2 ] = 0.385mm²/mm
[Link]
Av.req0 = = 0.643mm²/mm
fyt ㆍ d
[Link] = max [ [Link] , Av.req0 ] = 0.643mm²/mm
(3) Calculate shear strength by stirrup
Nleg = 2 Av1 = 78.60mm² (P10)
Av fyt d
øVs = ø = 105kN
s
(4) Calculate ratio of shear capacity
øVn = øVc + øVs = 151kN
Vu / øVn = 0.532 → O.K
(5) Calculate spacing limits for reinforcement
smax.0 = min [ d/2, 600mm ] = 158mm
Nleg Av1
sreq = = 245mm
[Link]
smax = min [ smax.0 sreq ] = 158mm
s = 80.00mm < smax = 158mm → O.K
Section : MIDDLE
1. General Information
(1) Design Code : ACI318M-14
(2) Code Unit : N, mm
2. Material
(1) F'c : 21.00MPa
(2) Fy : 420MPa
(3) Fys : 227MPa
3. Section
(1) Section Size : 250 x 375mm (R-Section)
(2) Cover : 40.00mm
(3) Compression : Not Considered
(4) Splicing Limit : 0%
2023-09-15 07:42 3
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 43B3(100)
250
40
375
40
4. Moments and Forces
(1) Mu,top : 55.60kN·m
(2) Mu,bottom : 17.12kN·m
(3) Vu : 76.78kN
5. Reinforcement
(1) Top Bar : 2-P20 (As = 628mm²)
Layer 1 : 2 EA (Cc = 60.00mm)
(2) Bot Bar : 2-P20 (As = 628mm²)
Layer 1 : 2 EA (Cc = 60.00mm)
(3) Stirrup : 2-P10@100 (As = 157mm²)
6. Check Bending Moment Capacity (Positive)
(1) Calculate design parameter
β1 = 0.850
(2) Check space of rebar
280 280
smax1 = 380 ( ) - 2.5cc smax2 = 300 ( )
fs fs
smax = min ( smax1 , smax2 ) = 255mm, Nreq =2
s = 130 < 255mm → O.K
(3) Calculate required ratio of reinforcement
( f'c )1/2 1.4
ρmin.11 = 0.25 ρmin.12 =
fy fy
ρmin.1 = max ( ρmin.11 , ρmin.12 ) = 0.0033
4 Mu
ρmin.2 = = 0.0025
3 ø fy bd(d-a/2)
ρmin = min ( ρmin1 , ρmin2 ) = 0.0025
f'c εc
ρεt = 0.85 β1 ( )( ) = 0.0155
fy εc + 0.004
ρmax = ρet = 0.0155
(4) Check ratio of tensile reinforcement
As
ρ= = 0.0080
bw d
ρmin < ρ < ρmax → O.K
2023-09-15 07:42 4
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 43B3(100)
(5) Calculate moment capacity
As fy
a= = 59.14mm
0.85 f'c bw
ø = 0.900
Mn = As fy (d - a/2) = 75.33kN·m
øMn = 67.80kN·m
(6) Calculate ratio of moment capacity
Mu / øMn = 0.253 → O.K
7. Check Bending Moment Capacity (Negative)
(1) Calculate design parameter
β1 = 0.850
(2) Check space of rebar
280 280
smax1 = 380 ( ) - 2.5cc smax2 = 300 ( )
fs fs
smax = min ( smax1 , smax2 ) = 255mm, Nreq =2
s = 130 < 255mm → O.K
(3) Calculate required ratio of reinforcement
( f'c )1/2 1.4
ρmin.11 = 0.25 ρmin.12 =
fy fy
ρmin.1 = max ( ρmin.11 , ρmin.12 ) = 0.0033
4 Mu
ρmin.2 = = 0.0086
3 ø fy bd(d-a/2)
ρmin = min ( ρmin1 , ρmin2 ) = 0.0033
f'c εc
ρεt = 0.85 β1 ( )( ) = 0.0155
fy εc + 0.004
ρmax = ρet = 0.0155
(4) Check ratio of tensile reinforcement
As
ρ= = 0.0080
bw d
ρmin < ρ < ρmax → O.K
(5) Calculate moment capacity
As fy
a= = 59.14mm
0.85 f'c bw
ø = 0.900
Mn = As fy (d - a/2) = 75.33kN·m
øMn = 67.80kN·m
(6) Calculate ratio of moment capacity
Mu / øMn = 0.820 → O.K
8. Check Shear Capacity
(1) Calculate shear strength by concrete
ø = 0.750 d = 315mm
øVc = ø 0.17 f'c bw d = 46.01kN
Vu > øVc → Shear reinforcement is required
(2) Calculate required shear strength by shear reinforcement
[Link] = ( Vu - øVc ) / ø = 41.02kN
Vc1 = 0.33 f'c bw d = 119kN Refer to [[Link]]
Vc2 = 0.66 f'c bw d = 238kN
[Link] < Vc2 → O.K
bw bw
Av.min1/s = 0.062 f'c Av.min2/s = 0.35
fyt fyt
[Link] = max [ Av.min1 , Av.min2 ] = 0.385mm²/mm
2023-09-15 07:42 5
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : 43B3(100)
[Link]
Av.req0 = = 0.574mm²/mm
fyt ㆍ d
[Link] = max [ [Link] , Av.req0 ] = 0.574mm²/mm
(3) Calculate shear strength by stirrup
Nleg = 2 Av1 = 78.60mm² (P10)
Av fyt d
øVs = ø = 84.30kN
s
(4) Calculate ratio of shear capacity
øVn = øVc + øVs = 130kN
Vu / øVn = 0.589 → O.K
(5) Calculate spacing limits for reinforcement
smax.0 = min [ d/2, 600mm ] = 158mm
Nleg Av1
sreq = = 274mm
[Link]
smax = min [ smax.0 sreq ] = 158mm
s = 100mm < smax = 158mm → O.K
2023-09-15 07:42 6
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : F1
1. General Information
(1) Design Code : ACI318M-14 2,700
(2) Code Unit : N, mm
1,350 1,350
2. Material
(1) F'c : 21.00MPa
(2) Fy : 420MPa
1,350
3. Section
2,700
(1) Section Size
Depth : 400mm Y1
1,350
Cover : 75.00mm
(2) Column Section X1
Shape of Column : Rectangle
Section : 450x450mm
4. Rebar
(1) Direction Y
Layer 1 : P16@250 (As = 804mm²)
2,100
(2) Direction X
Layer 1 : P16@250 (As = 804mm²)
5. Foundation
400
(1) Foundation Size
Lx : 2.700m
Ly : 2.700m
fe : 150kN/m²
6. Design Load
(1) Service Load ( by Load Combinations )
Ps Msx Msy
No. CHK Name Description
(kN) (kN·m) (kN·m)
- - cLCB17 424 27.03 106 SERV :(D) + EX+/1.4
1 Yes cLCB13 542 28.40 5.983 SERV :(D) + (L)
2 Yes cLCB18 393 108 13.06 SERV :(D) + EY+/1.4
3 Yes cLCB20 453 -54.60 -1.272 SERV :(D) - EY+/1.4
4 Yes cLCB17 424 27.03 106 SERV :(D) + EX+/1.4
5 Yes cLCB19 422 26.02 -94.40 SERV :(D) - EX+/1.4
(2) Factored Load ( by Load Combinations )
Pu Mux Muy
No. CHK Name Description
(kN) (kN·m) (kN·m)
- - cLCB2 698 34.83 7.214 1.2(D) + 1.6L + 0.5LR
1 Yes cLCB2 698 34.83 7.214 1.2(D) + 1.6L + 0.5LR
2 Yes cLCB9 339 137 15.34 0.9D + 1.0EY+
3 Yes cLCB5 525 146 17.15 1.2D + 1.0EY+ + 1.0(1.0(0.5)L)
4 Yes cLCB11 423 -89.71 -4.729 0.9D - 1.0EY+
5 Yes cLCB4 568 33.47 148 1.2D + 1.0EX+ + 1.0(1.0(0.5)L)
6 Yes cLCB10 379 23.16 -135 0.9D - 1.0EX+
(3) Surcharge Load
Surface Load : 0.000KPa
Weight Density : 18.00kN/m³
Soil Height : 2.100m
2023-09-15 07:58 1
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : F1
(4) Self weight is considered.
7. Check Soil Capacity
(1) Calculate actual soil stress
qs,top-left = 80.92kN/m² qs,top-right = 146kN/m²
qs,bot-left = 64.44kN/m² qs,bot-right = 129kN/m²
qs,max = 146kN/m²
qs,max / fe = 0.969 → O.K
(2) Calculate factored soil stress
qu,top-left = 176kN/m² qu,top-right = 180kN/m²
qu,bot-left = 154kN/m² qu,bot-right = 159kN/m²
qu,max = 180kN/m² qu,min = 154kN/m²
8. Check Shear
(1) Calculate one-way shear
ø = 0.750
Vux = 151kN øVcx = 500kN
Vux / øVcx = 0.302 → O.K
Vuy = 171kN øVcy = 475kN
Vuy / øVcy = 0.361 → O.K
(2) Calculate two-way shear
b0 Vc1 Vc2 Vc3 Vc Vu øV c
- Ratio
(mm) (kN) (kN) (kN) (kN) (kN) (kN)
Interior 3,068 2,273 2,269 1,471 1,471 1,078 1,103 0.977
Edge(X) 4,234 3,137 2,168 2,030 2,030 954 1,522 0.627
Edge(Y) 4,234 3,137 2,168 2,030 2,030 954 1,522 0.627
Corner 3,467 2,569 1,600 1,662 1,600 674 1,200 0.562
INTERIOR EDGE( X ) EDGE( Y ) CORNER
ø = 0.750
d = 317mm
2
Vc1 = 0.17 ( 1 + ) f'c b0 d
β
as d
Vc2 = 0.083 ( + 2 ) f'c b0 d
b0
Vc3 = 0.33 f'c b0 d
Vc = min(Vc1 , Vc2 , Vc3 )
Vu = 1,078kN
Vu / øVc = 0.977 → O.K
9. Check Moment Capacity
(1) Calculate moment capacity (Direction X)
ø = 0.900
2023-09-15 07:58 2
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : F1
Muy = 61.58kN·m øMny = 93.51kN·m
Muy / øMny = 0.659 → O.K
(2) Calculate moment capacity (Direction Y)
ø = 0.900
Mux = 65.43kN·m øMnx = 88.65kN·m
Mux / øMnx = 0.738 → O.K
10. Check Rebar
(1) Calculate minimum rebar area required
As,min = 0.00180D = 720mm²
(2) Calculate minimum rebar space required (Direction Y)
As = 201mm² (P16@250)
sreq. = 279mm
sx = 250mm < sreq. = 279mm → O.K
(3) Calculate minimum rebar space required (Direction X)
As = 201mm² (P16@250)
sreq. = 279mm
sy = 250mm < sreq. = 279mm → O.K
2023-09-15 07:58 3
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : F2
1. General Information
(1) Design Code : ACI318M-14 2,600
(2) Code Unit : N, mm
1,300 1,300
2. Material
(1) F'c : 21.00MPa
(2) Fy : 420MPa
1,300
3. Section
2,600
(1) Section Size
Depth : 400mm Y1
1,300
Cover : 75.00mm
(2) Column Section X1
Shape of Column : Rectangle
Section : 450x450mm
4. Rebar
(1) Direction Y
Layer 1 : P16@250 (As = 804mm²)
2,100
(2) Direction X
Layer 1 : P16@250 (As = 804mm²)
5. Foundation
400
(1) Foundation Size
Lx : 2.600m
Ly : 2.600m
fe : 150kN/m²
6. Design Load
(1) Service Load ( by Load Combinations )
Ps Msx Msy
No. CHK Name Description
(kN) (kN·m) (kN·m)
- - cLCB19 441 6.543 -93.31 SERV :(D) - EX+/1.4
1 Yes cLCB13 513 5.930 7.599 SERV :(D) + (L)
2 Yes cLCB18 392 94.82 13.05 SERV :(D) + EY+/1.4
3 Yes cLCB20 448 -81.65 0.0923 SERV :(D) - EY+/1.4
4 Yes cLCB17 399 6.632 106 SERV :(D) + EX+/1.4
5 Yes cLCB19 441 6.543 -93.31 SERV :(D) - EX+/1.4
(2) Factored Load ( by Load Combinations )
Pu Mux Muy
No. CHK Name Description
(kN) (kN·m) (kN·m)
- - cLCB2 653 6.846 9.530 1.2(D) + 1.6L + 0.5LR
1 Yes cLCB2 653 6.846 9.530 1.2(D) + 1.6L + 0.5LR
2 Yes cLCB9 339 129 14.99 0.9D + 1.0EY+
3 Yes cLCB5 512 131 17.47 1.2D + 1.0EY+ + 1.0(1.0(0.5)L)
4 Yes cLCB11 417 -118 -3.157 0.9D - 1.0EY+
5 Yes cLCB4 522 7.638 148 1.2D + 1.0EX+ + 1.0(1.0(0.5)L)
6 Yes cLCB10 407 5.867 -134 0.9D - 1.0EX+
(3) Surcharge Load
Surface Load : 0.000KPa
Weight Density : 18.00kN/m³
Soil Height : 2.100m
2023-09-15 07:59 1
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : F2
(4) Self weight is considered.
7. Check Soil Capacity
(1) Calculate actual soil stress
qs,top-left = 146kN/m² qs,top-right = 82.43kN/m²
qs,bot-left = 142kN/m² qs,bot-right = 77.96kN/m²
qs,max = 146kN/m²
qs,max / fe = 0.972 → O.K
(2) Calculate factored soil stress
qu,top-left = 167kN/m² qu,top-right = 174kN/m²
qu,bot-left = 162kN/m² qu,bot-right = 169kN/m²
qu,max = 174kN/m² qu,min = 162kN/m²
8. Check Shear
(1) Calculate one-way shear
ø = 0.750
Vux = 136kN øVcx = 482kN
Vux / øVcx = 0.283 → O.K
Vuy = 142kN øVcy = 457kN
Vuy / øVcy = 0.310 → O.K
(2) Calculate two-way shear
b0 Vc1 Vc2 Vc3 Vc Vu øV c
- Ratio
(mm) (kN) (kN) (kN) (kN) (kN) (kN)
Interior 3,068 2,273 2,269 1,471 1,471 995 1,103 0.902
Edge(X) 4,134 3,063 2,144 1,982 1,982 877 1,486 0.590
Edge(Y) 4,134 3,063 2,144 1,982 1,982 877 1,486 0.590
Corner 3,367 2,494 1,576 1,614 1,576 618 1,182 0.522
INTERIOR EDGE( X ) EDGE( Y ) CORNER
ø = 0.750
d = 317mm
2
Vc1 = 0.17 ( 1 + ) f'c b0 d
β
as d
Vc2 = 0.083 ( + 2 ) f'c b0 d
b0
Vc3 = 0.33 f'c b0 d
Vc = min(Vc1 , Vc2 , Vc3 )
Vu = 995kN
Vu / øVc = 0.902 → O.K
9. Check Moment Capacity
(1) Calculate moment capacity (Direction X)
ø = 0.900
2023-09-15 07:59 2
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : F2
Muy = 57.21kN·m øMny = 93.51kN·m
Muy / øMny = 0.612 → O.K
(2) Calculate moment capacity (Direction Y)
ø = 0.900
Mux = 56.82kN·m øMnx = 88.65kN·m
Mux / øMnx = 0.641 → O.K
10. Check Rebar
(1) Calculate minimum rebar area required
As,min = 0.00180D = 720mm²
(2) Calculate minimum rebar space required (Direction Y)
As = 201mm² (P16@250)
sreq. = 279mm
sx = 250mm < sreq. = 279mm → O.K
(3) Calculate minimum rebar space required (Direction X)
As = 201mm² (P16@250)
sreq. = 279mm
sy = 250mm < sreq. = 279mm → O.K
2023-09-15 07:59 3
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : F3
1. General Information
(1) Design Code : ACI318M-14 2,500
(2) Code Unit : N, mm
1,250 1,250
2. Material
(1) F'c : 21.00MPa
(2) Fy : 420MPa
1,250
y
3. Section
2,500
(1) Section Size x
Depth : 350mm Y1
1,250
Cover : 75.00mm
(2) Column Section X1
Shape of Column : Rectangle
Section : 450x450mm
4. Rebar
(1) Direction Y
Layer 1 : P16@300 (As = 670mm²)
2,150
(2) Direction X
Layer 1 : P16@300 (As = 670mm²)
5. Foundation
350
(1) Foundation Size
Lx : 2.500m
Ly : 2.500m
fe : 150kN/m²
6. Design Load
(1) Service Load ( by Load Combinations )
Ps Msx Msy
No. CHK Name Description
(kN) (kN·m) (kN·m)
- - cLCB17 344 -5.275 96.73 SERV :(D) + EX+/1.4
1 Yes cLCB13 397 -3.766 0.637 SERV :(D) + (L)
2 Yes cLCB20 310 -84.12 9.448 SERV :(D) - EY+/1.4
3 Yes cLCB18 381 74.26 -8.436 SERV :(D) + EY+/1.4
4 Yes cLCB17 344 -5.275 96.73 SERV :(D) + EX+/1.4
5 Yes cLCB19 346 -4.583 -95.72 SERV :(D) - EX+/1.4
(2) Factored Load ( by Load Combinations )
Pu Mux Muy
No. CHK Name Description
(kN) (kN·m) (kN·m)
- - cLCB2 503 -4.028 0.807 1.2(D) + 1.6L + 0.5LR
1 Yes cLCB2 503 -4.028 0.807 1.2(D) + 1.6L + 0.5LR
2 Yes cLCB11 261 -115 12.97 0.9D - 1.0EY+
3 Yes cLCB9 360 106 -12.06 0.9D + 1.0EY+
4 Yes cLCB7 390 -116 13.19 1.2D - 1.0EY+ + 1.0(1.0(0.5)L)
5 Yes cLCB4 438 -5.818 135 1.2D + 1.0EX+ + 1.0(1.0(0.5)L)
6 Yes cLCB10 312 -3.952 -134 0.9D - 1.0EX+
(3) Surcharge Load
Surface Load : 0.000KPa
Weight Density : 18.00kN/m³
Soil Height : 2.150m
2023-09-15 07:59 1
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : F3
(4) Self weight is considered.
7. Check Soil Capacity
(1) Calculate actual soil stress
qs,top-left = 62.47kN/m² qs,top-right = 137kN/m²
qs,bot-left = 66.52kN/m² qs,bot-right = 141kN/m²
qs,max = 141kN/m²
qs,max / fe = 0.937 → O.K
(2) Calculate factored soil stress
qu,top-left = 150kN/m² qu,top-right = 151kN/m²
qu,bot-left = 153kN/m² qu,bot-right = 154kN/m²
qu,max = 154kN/m² qu,min = 150kN/m²
8. Check Shear
(1) Calculate one-way shear
ø = 0.750
Vux = 105kN øVcx = 390kN
Vux / øVcx = 0.270 → O.K
Vuy = 113kN øVcy = 367kN
Vuy / øVcy = 0.308 → O.K
(2) Calculate two-way shear
b0 Vc1 Vc2 Vc3 Vc Vu øV c
- Ratio
(mm) (kN) (kN) (kN) (kN) (kN) (kN)
Interior 2,868 1,790 1,667 1,158 1,158 835 869 0.961
Edge(X) 3,934 2,455 1,612 1,588 1,588 738 1,191 0.619
Edge(Y) 3,934 2,455 1,612 1,588 1,588 738 1,191 0.619
Corner 3,217 2,007 1,196 1,299 1,196 520 897 0.580
INTERIOR EDGE( X ) EDGE( Y ) CORNER
ø = 0.750
d = 267mm
2
Vc1 = 0.17 ( 1 + ) f'c b0 d
β
as d
Vc2 = 0.083 ( + 2 ) f'c b0 d
b0
Vc3 = 0.33 f'c b0 d
Vc = min(Vc1 , Vc2 , Vc3 )
Vu = 835kN
Vu / øVc = 0.961 → O.K
9. Check Moment Capacity
(1) Calculate moment capacity (Direction X)
ø = 0.900
2023-09-15 07:59 2
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : F3
Muy = 42.39kN·m øMny = 65.66kN·m
Muy / øMny = 0.646 → O.K
(2) Calculate moment capacity (Direction Y)
ø = 0.900
Mux = 42.87kN·m øMnx = 61.60kN·m
Mux / øMnx = 0.696 → O.K
10. Check Rebar
(1) Calculate minimum rebar area required
As,min = 0.00180D = 630mm²
(2) Calculate minimum rebar space required (Direction Y)
As = 201mm² (P16@300)
sreq. = 319mm
sx = 300mm < sreq. = 319mm → O.K
(3) Calculate minimum rebar space required (Direction X)
As = 201mm² (P16@300)
sreq. = 319mm
sy = 300mm < sreq. = 319mm → O.K
2023-09-15 07:59 3
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : CF1
1. General Information
(1) Design Code : ACI318M-14
(2) Code Unit : N, mm
2. Material
(1) F'c : 21.00MPa
(2) Fy : 420MPa
3. Design Load
(1) Column 1
Ps : 262kN
Pu : 242kN
(2) Column 2
Ps : 278kN
Pu : 532kN
(3) Surcharge Load
Surface Load : 0.000KPa
Weight Density : 18.00kN/m³
Soil Height : 2.150m
(4) Self weight is considered.
4. Foundation
(1) Foundation Size
Lx : 3.720m
Ly : 2.300m
Depth : 350mm
Cover : 75.00mm
(2) Soil Bearing Capacity
fe : 150kN/m²
5. Column
No. Shape Section Lxi
1 Rectangle 350x450mm 0.175m
2 Rectangle 450x450mm 2.622m
2023-09-15 07:59 1
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : CF1
3720
2300
450
450
Y 350 450
X
2150
P20@300
P25@250 P25@250
350
P20@300 P20@300
P20@300
175 2622 923
-119.95
(-)
0.00 -31.81
[B.M.D]
38.13
(+) 59.15
-261.91
2023-09-15 07:59 2
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : CF1
6. Rebar
(1) Direction X
Cantilever(L) : P20@300 (As = 1,047mm²)
Colm (1) : P20@300 (As = 1,047mm²)
Span (1-2) : P20@300 (As = 1,047mm²)
Colm (2) : P20@300 (As = 1,047mm²)
Cantilever(R) : P20@300 (As = 1,047mm²)
(2) Direction Y
Colm (1) : P25@250 (As = 1,964mm²)
Colm (2) : P25@250 (As = 1,964mm²)
7. Check Soil Capacity
(1) Calculate actual soil stress
qs,left = 144kN/m² qs,right = 75.64kN/m²
qs,max = 144kN/m²
qs,max / fe = 0.956 → O.K
(2) Calculate factored soil stress
qu,left = 73.14kN/m² qu,right = 108kN/m²
qu,max = 108kN/m² qu,min = 73.14kN/m²
8. Check Shear
(1) Calculate one-way shear
ø = 0.750
Vux = 204kN øVcx = 356kN
Vux / øVcx = 0.574 → O.K
(2) Calculate two-way shear
b0 Vc1 Vc2 Vc3 Vc Vu øV c
Column Position Ratio
(mm) (kN) (kN) (kN) (kN) (kN) (kN)
1 Edge(X) 1,658 837 1,055 636 636 211 477 0.443
2 Interior 2,815 1,669 1,523 1,080 1,080 488 810 0.602
ø = 0.750
d = 0.000mm
2
Vc1 = 0.17 ( 1 + ) f'c b0 d
β
as d
Vc2 = 0.083 ( + 2 ) f'c b0 d
b0
Vc3 = 0.33 f'c b0 d
Vc = min(Vc1 , Vc2 , Vc3 )
Vu = 488kN
Vu / øVc = 0.602 → O.K
9. Check Moment Capacity
(1) Calculate moment capacity (Direction X)
Position Top/Bottom ø Mu(kN·m/m) øMn(kN·m/m) Ratio Remark
Cantilever(L) Bottom 0.900 0.000 100 0.000 OK
Colm (1) Bottom 0.900 0.000 100 0.000 OK
Span (1-2) Top 0.900 -52.15 100 0.521 OK
Colm (2) Bottom 0.900 25.72 100 0.257 OK
Cantilever(R) Bottom 0.900 25.72 100 0.257 OK
(2) Calculate moment capacity (Direction Y)
Position Top/Bottom ø Mu(kN·m/m) øMn(kN·m/m) Ratio Remark
2023-09-15 07:59 3
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : CF1
Colm (1) Bottom 0.900 95.34 163 0.585 OK
Colm (2) Bottom 0.900 143 163 0.878 OK
10. Check Rebar
(1) Calculate minimum rebar area required
As,min = 0.00180D = 630mm²
(2) Calculate minimum rebar space required (Direction X)
Position Top/Bottom Rebar As(mm²) Smax(mm) Sreq(mm) Remark
Cantilever(L) Bottom P20@300 314 450 450 OK
Colm (1) Bottom P20@300 314 450 450 OK
Span (1-2) Top P20@300 314 450 450 OK
Colm (2) Bottom P20@300 314 450 450 OK
Cantilever(R) Bottom P20@300 314 450 450 OK
(3) Calculate minimum rebar space required (Direction Y)
Position Top/Bottom Rebar As(mm²) Smax(mm) Sreq(mm) Remark
Colm (1) Bottom P25@250 491 450 450 OK
Colm (2) Bottom P25@250 491 450 450 OK
2023-09-15 07:59 4
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : CF2
1. General Information
(1) Design Code : ACI318M-14
(2) Code Unit : N, mm
2. Material
(1) F'c : 21.00MPa
(2) Fy : 420MPa
3. Design Load
(1) Column 1
Service Load ( by Load Combinations )
Ps
No. CHK Name Description
(kN)
- - cLCB19 224 SERV :(D) - EX+/1.4
1 Yes cLCB12 139 SERV :(D)
2 Yes cLCB13 135 SERV :(D) + (L)
3 Yes cLCB14 139 SERV :(D) + LR
4 Yes cLCB15 136 SERV :(D) + 0.75(L+LR)
5 Yes cLCB16 136 SERV :(D) + 0.75(L)
6 Yes cLCB17 53.03 SERV :(D) + EX+/1.4
7 Yes cLCB18 177 SERV :(D) + EY+/1.4
8 Yes cLCB19 224 SERV :(D) - EX+/1.4
9 Yes cLCB20 100 SERV :(D) - EY+/1.4
Factored Load ( by Load Combinations )
Pu
No. CHK Name Description
(kN)
- - cLCB6 285 1.2D - 1.0EX+ + 1.0(1.0(0.5)L)
1 Yes cLCB1 194 1.4(D)
2 Yes cLCB2 161 1.2(D) + 1.6L + 0.5LR
3 Yes cLCB3 165 1.2D + 1.6LR + 1.0(1.0(0.5)L)
4 Yes cLCB4 44.88 1.2D + 1.0EX+ + 1.0(1.0(0.5)L)
5 Yes cLCB5 219 1.2D + 1.0EY+ + 1.0(1.0(0.5)L)
6 Yes cLCB6 285 1.2D - 1.0EX+ + 1.0(1.0(0.5)L)
7 Yes cLCB7 111 1.2D - 1.0EY+ + 1.0(1.0(0.5)L)
8 Yes cLCB8 4.895 0.9D + 1.0EX+
9 Yes cLCB9 179 0.9D + 1.0EY+
10 Yes cLCB10 245 0.9D - 1.0EX+
11 Yes cLCB11 70.87 0.9D - 1.0EY+
(2) Column 2
Service Load ( by Load Combinations )
Ps
No. CHK Name Description
(kN)
- - cLCB19 222 SERV :(D) - EX+/1.4
1 Yes cLCB12 271 SERV :(D)
2 Yes cLCB13 295 SERV :(D) + (L)
3 Yes cLCB14 271 SERV :(D) + LR
4 Yes cLCB15 289 SERV :(D) + 0.75(L+LR)
5 Yes cLCB16 289 SERV :(D) + 0.75(L)
6 Yes cLCB17 320 SERV :(D) + EX+/1.4
2023-09-15 08:00 1
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : CF2
7 Yes cLCB18 299 SERV :(D) + EY+/1.4
8 Yes cLCB19 222 SERV :(D) - EX+/1.4
9 Yes cLCB20 243 SERV :(D) - EY+/1.4
Factored Load ( by Load Combinations )
Pu
No. CHK Name Description
(kN)
- - cLCB6 268 1.2D - 1.0EX+ + 1.0(1.0(0.5)L)
1 Yes cLCB1 379 1.4(D)
2 Yes cLCB2 364 1.2(D) + 1.6L + 0.5LR
3 Yes cLCB3 337 1.2D + 1.6LR + 1.0(1.0(0.5)L)
4 Yes cLCB4 405 1.2D + 1.0EX+ + 1.0(1.0(0.5)L)
5 Yes cLCB5 376 1.2D + 1.0EY+ + 1.0(1.0(0.5)L)
6 Yes cLCB6 268 1.2D - 1.0EX+ + 1.0(1.0(0.5)L)
7 Yes cLCB7 298 1.2D - 1.0EY+ + 1.0(1.0(0.5)L)
8 Yes cLCB8 312 0.9D + 1.0EX+
9 Yes cLCB9 283 0.9D + 1.0EY+
10 Yes cLCB10 175 0.9D - 1.0EX+
11 Yes cLCB11 204 0.9D - 1.0EY+
(3) Surcharge Load
Surface Load : 0.000KPa
Weight Density : 18.00kN/m³
Soil Height : 2.150m
(4) Self weight is considered.
4. Foundation
(1) Foundation Size
Lx : 3.720m
Ly : 2.000m
Depth : 350mm
Cover : 75.00mm
(2) Soil Bearing Capacity
fe : 150kN/m²
5. Column
No. Shape Section Lxi
1 Rectangle 350x450mm 0.175m
2 Rectangle 450x450mm 2.622m
2023-09-15 08:00 2
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : CF2
3720
2000
450
450
Y 350 450
X
2150
P20@300
P25@250 P25@250
350
P20@300 P20@300
P20@300
175 2622 923
-129.49
(-)
-35.04 -14.20
0.00
[B.M.D]
15.14
(+)
-176.28
(-)
0.00
[S.F.D]
47.69
(+)
2023-09-15 08:00 3
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : CF2
6. Rebar
(1) Direction X
Cantilever(L) : P20@300 (As = 1,047mm²)
Colm (1) : P20@300 (As = 1,047mm²)
Span (1-2) : P20@300 (As = 1,047mm²)
Colm (2) : P20@300 (As = 1,047mm²)
Cantilever(R) : P20@300 (As = 1,047mm²)
(2) Direction Y
Colm (1) : P25@250 (As = 1,964mm²)
Colm (2) : P25@250 (As = 1,964mm²)
7. Check Soil Capacity
(1) Calculate actual soil stress
qs,left = 144kN/m² qs,right = 69.67kN/m²
qs,max = 144kN/m²
qs,max / fe = 0.955 → O.K
(2) Calculate factored soil stress
qu,left = 124kN/m² qu,right = 24.88kN/m²
qu,max = 124kN/m² qu,min = 24.88kN/m²
8. Check Shear
(1) Calculate one-way shear
ø = 0.750
Vux = 145kN øVcx = 310kN
Vux / øVcx = 0.467 → O.K
(2) Calculate two-way shear
b0 Vc1 Vc2 Vc3 Vc Vu øV c
Column Position Ratio
(mm) (kN) (kN) (kN) (kN) (kN) (kN)
1 Edge(X) 1,658 837 1,055 636 636 260 477 0.545
2 Interior 2,815 1,669 1,523 1,080 1,080 232 810 0.286
ø = 0.750
d = 0.000mm
2
Vc1 = 0.17 ( 1 + ) f'c b0 d
β
as d
Vc2 = 0.083 ( + 2 ) f'c b0 d
b0
Vc3 = 0.33 f'c b0 d
Vc = min(Vc1 , Vc2 , Vc3 )
Vu = 260kN
Vu / øVc = 0.545 → O.K
9. Check Moment Capacity
(1) Calculate moment capacity (Direction X)
Position Top/Bottom ø Mu(kN·m/m) øMn(kN·m/m) Ratio Remark
Cantilever(L) Bottom 0.900 0.000 100 0.000 OK
Colm (1) Bottom 0.900 0.000 100 0.000 OK
Span (1-2) Top 0.900 -64.75 100 0.647 OK
Colm (2) Bottom 0.900 7.568 100 0.0757 OK
Cantilever(R) Bottom 0.900 7.568 100 0.0757 OK
(2) Calculate moment capacity (Direction Y)
Position Top/Bottom ø Mu(kN·m/m) øMn(kN·m/m) Ratio Remark
2023-09-15 08:00 4
MIDASIT [Link]
TEL:1-646-852-9286
MEMBER NAME : CF2
Colm (1) Bottom 0.900 90.72 163 0.557 OK
Colm (2) Bottom 0.900 58.21 163 0.357 OK
10. Check Rebar
(1) Calculate minimum rebar area required
As,min = 0.00180D = 630mm²
(2) Calculate minimum rebar space required (Direction X)
Position Top/Bottom Rebar As(mm²) Smax(mm) Sreq(mm) Remark
Cantilever(L) Bottom P20@300 314 450 450 OK
Colm (1) Bottom P20@300 314 450 450 OK
Span (1-2) Top P20@300 314 450 450 OK
Colm (2) Bottom P20@300 314 450 450 OK
Cantilever(R) Bottom P20@300 314 450 450 OK
(3) Calculate minimum rebar space required (Direction Y)
Position Top/Bottom Rebar As(mm²) Smax(mm) Sreq(mm) Remark
Colm (1) Bottom P25@250 491 450 450 OK
Colm (2) Bottom P25@250 491 450 450 OK
2023-09-15 08:00 5
midas Gen Steel Checking Result
Company Project Title
Author JPPES File Name HUANG CB [Link]
z
1. Design Information
0.006
0.006
Design Code AISC(15th)-LRFD16
Unit System kN, m y
0.0508
Member No 279
0.036
Material A36 (No:2)
(Fy = 248211, Es = 199948024)
Section Name TOP AND BOTTOM CHORD (No:18) 0.015
(Built-up Section).
0.0508
Member Length : 0.71007
2. Member Forces Depth 0.05080 Web Thick 0.00600
Axial Force Fxx = 13.3495 (LCB: 6, POS:J) Top F Width 0.05080 Top F Thick 0.00600
Bending Moments My = -0.8003, Mz = 0.00012 Area 0.00057 Asz 0.00020
Qyb 0.00064 Qzb 0.00064
End Moments Myi = -0.3210, Myj = -0.8003 (for Lb) Iyy 0.00000 Izz 0.00000
Ybar 0.01490 Zbar 0.03590
Myi = -0.3210, Myj = -0.8003 (for Ly) Syy 0.00000 Szz 0.00000
Mzi = -0.0000, Mzj = 0.00012 (for Lz) rp 0.00995
Shear Forces Fyy = -0.0564 (LCB: 12, POS:1/2)
Fzz = 6.12286 (LCB: 6, POS:J)
3. Design Parameters
Unbraced Lengths Ly = 0.71007, Lz = 0.71007, Lb = 0.71007
Effective Length Factors Ky = 1.00, Kz = 1.00
Moment Factor / Bending Coefficient
Cmy = 1.00, Cmz = 1.00, Cb = 2.17
4. Checking Results
Slenderness Ratio
KL/r = 71.4 < 200.0 (Memb:160, LCB: 8)................................... O.K
Axial Strength
Pr/Pc = 13.349/128.137 = 0.104 < 1.000 ..................................... O.K
Bending Strength
Mru/Mcu = 0.56583/2.04563 = 0.277 < 1.000 ................................... O.K
Mrv/Mcv = 0.56601/0.90236 = 0.627 < 1.000 ................................... O.K
Combined Strength (Tension+Bending)
Pr/Pc = 0.10 < 0.20
Rmax = Pr/(2*Pc) + [Mru/Mcu + Mrv/Mcv] = 0.956 < 1.000 ............................ O.K
Shear Strength
Vry/Vcy = 0.001 < 1.000 ...................................................... O.K
Vrz/Vcz = 0.150 < 1.000 ...................................................... O.K
Modeling, Integrated Design & Analysis Software Print Date/Time : 09/14/2023 18:38
midas Gen Steel Checking Result
Company Project Title
Author JPPES File Name HUANG CB [Link]
z
1. Design Information
0.004
0.004
Design Code AISC(15th)-LRFD16
Unit System kN, m y
0.0508
Member No 312
0.037
Material A36 (No:2)
(Fy = 248211, Es = 199948024)
Section Name WEB (No:17) 0.014
(Built-up Section).
0.0508
Member Length : 0.38367
2. Member Forces Depth 0.05080 Web Thick 0.00400
Axial Force Fxx = -29.718 (LCB: 6, POS:I) Top F Width 0.05080 Top F Thick 0.00400
Bending Moments My = 0.00031, Mz = 0.18362 Area 0.00039 Asz 0.00014
Qyb 0.00067 Qzb 0.00067
End Moments Myi = 0.00031, Myj = 0.00002 (for Lb) Iyy 0.00000 Izz 0.00000
Ybar 0.01418 Zbar 0.03662
Myi = 0.00031, Myj = 0.00002 (for Ly) Syy 0.00000 Szz 0.00000
Mzi = 0.18362, Mzj = -0.1233 (for Lz) rp 0.01004
Shear Forces Fyy = 0.80000 (LCB: 6, POS:1/2)
Fzz = 0.34892 (LCB: 10, POS:1/2)
3. Design Parameters
Unbraced Lengths Ly = 0.38367, Lz = 0.38367, Lb = 0.38367
Effective Length Factors Ky = 1.00, Kz = 1.00
Moment Factor / Bending Coefficient
Cmy = 0.85, Cmz = 0.85, Cb = 1.00
4. Checking Results
Slenderness Ratio
KL/r = 119.5 < 200.0 (Memb:280, LCB: 7)................................... O.K
Axial Strength
Pr/Pc = 29.7179/62.5579 = 0.475 < 1.000 ..................................... O.K
Bending Strength
Mru/Mcu = 0.13005/1.44788 = 0.090 < 1.000 ................................... O.K
Mrv/Mcv = 0.12962/0.65818 = 0.197 < 1.000 ................................... O.K
Combined Strength (Compression+Bending)
Pr/Pc = 0.48 > 0.20
Rmax = Pr/Pc + 8/9*[Mru/Mcu + Mrv/Mcv] = 0.730 < 1.000 ............................ O.K
Shear Strength
Vry/Vcy = 0.029 < 1.000 ...................................................... O.K
Vrz/Vcz = 0.013 < 1.000 ...................................................... O.K
Modeling, Integrated Design & Analysis Software Print Date/Time : 09/14/2023 18:38
Vous aimerez peut-être aussi
- Tables de croissance pour garçons (0-5 ans)Pas encore d'évaluationTables de croissance pour garçons (0-5 ans)34 pages
- Analyse des données de masse et tempsPas encore d'évaluationAnalyse des données de masse et temps2 pages
- Paramètres de régression et donnéesPas encore d'évaluationParamètres de régression et données18 pages
- Valeurs de puissance moteurs à inductionPas encore d'évaluationValeurs de puissance moteurs à induction1 page
- Analyse des Forces et Moments en StructurePas encore d'évaluationAnalyse des Forces et Moments en Structure4 pages
- Tableaux de couple et pression techniquesPas encore d'évaluationTableaux de couple et pression techniques1 page
- Temps d'attente et de vitaux par IDPas encore d'évaluationTemps d'attente et de vitaux par ID471 pages
- Valeurs critiques de la distribution FPas encore d'évaluationValeurs critiques de la distribution F4 pages
- Croissance quotidienne des investissementsPas encore d'évaluationCroissance quotidienne des investissements1 page
- Analyse statistique des données numériquesPas encore d'évaluationAnalyse statistique des données numériques79 pages
- Statistiques de Service par StationPas encore d'évaluationStatistiques de Service par Station271 pages
- Analyse des Forces et Moments dans une StructurePas encore d'évaluationAnalyse des Forces et Moments dans une Structure3 pages
- Quantification des Calibres de LaminaPas encore d'évaluationQuantification des Calibres de Lamina10 pages
- Statistiques de fitness par générationPas encore d'évaluationStatistiques de fitness par génération10 pages
- Tablau des Tubes Carrés et ÉpaisseursPas encore d'évaluationTablau des Tubes Carrés et Épaisseurs5 pages
- Conversion de Salinité par HydromètrePas encore d'évaluationConversion de Salinité par Hydromètre1 page
- Analyse des heures de sommeil des étudiantsPas encore d'évaluationAnalyse des heures de sommeil des étudiants3 pages
- Résultats d'essai IELTS - 3 nov. 2019Pas encore d'évaluationRésultats d'essai IELTS - 3 nov. 20197 pages
- Analyse des Données de Masse et VolumePas encore d'évaluationAnalyse des Données de Masse et Volume7 pages
- Analyse de Productivité des MachinesPas encore d'évaluationAnalyse de Productivité des Machines4 pages
- Données de points X et Y détailléesPas encore d'évaluationDonnées de points X et Y détaillées16 pages
- Commandes de production ALUMIX 2023Pas encore d'évaluationCommandes de production ALUMIX 20239 pages
- Modèle de sortie en volts par échantillonPas encore d'évaluationModèle de sortie en volts par échantillon2 pages
- Analyse des données statistiques X^2Pas encore d'évaluationAnalyse des données statistiques X^238 pages
- Analyse des données statistiques X^2Pas encore d'évaluationAnalyse des données statistiques X^229 pages
- Données de mouvement en projection horizontalePas encore d'évaluationDonnées de mouvement en projection horizontale4 pages
- Spécifications des tuyaux ANSI B36.10Pas encore d'évaluationSpécifications des tuyaux ANSI B36.103 pages
- Données numériques organisées par colonnesPas encore d'évaluationDonnées numériques organisées par colonnes1 page
- Besoins en eau pour l'irrigation des carottesPas encore d'évaluationBesoins en eau pour l'irrigation des carottes8 pages
- Données Météo Mensuelles en °C et mmPas encore d'évaluationDonnées Météo Mensuelles en °C et mm1 page
- Tableau de référence IMC enfants 5-17 ansPas encore d'évaluationTableau de référence IMC enfants 5-17 ans1 page
- Eurocode 3 : Fatigue des structures en acierPas encore d'évaluationEurocode 3 : Fatigue des structures en acier5 pages
- Installation sanitaire : Guide pratiquePas encore d'évaluationInstallation sanitaire : Guide pratique10 pages
- Visserie et Boulonnerie : Normes et TypesPas encore d'évaluationVisserie et Boulonnerie : Normes et Types11 pages
- Ra 2016-Manuel Construction Flower Toilet FR 0Pas encore d'évaluationRa 2016-Manuel Construction Flower Toilet FR 028 pages
- Guide Des Solutions 2012 Gros Oeuvre Partie 1Pas encore d'évaluationGuide Des Solutions 2012 Gros Oeuvre Partie 124 pages
- Étude de la dalle mixte acier-bétonPas encore d'évaluationÉtude de la dalle mixte acier-béton11 pages
- Rapport de stage en intelligence économiquePas encore d'évaluationRapport de stage en intelligence économique26 pages
- Expertise en Tuyauterie et ChaudronneriePas encore d'évaluationExpertise en Tuyauterie et Chaudronnerie10 pages
- Solutions de construction résistantesPas encore d'évaluationSolutions de construction résistantes2 pages
- Étude hydrologique et hydraulique des bassinsPas encore d'évaluationÉtude hydrologique et hydraulique des bassins154 pages
- Offre Technique - Rehabilitation - Ecole - Catholique - Saint - Barbe - MOUNANAPas encore d'évaluationOffre Technique - Rehabilitation - Ecole - Catholique - Saint - Barbe - MOUNANA54 pages
- Béton Renforcé de Fibres MétalliquesPas encore d'évaluationBéton Renforcé de Fibres Métalliques8 pages
- Étude de Poteaux et Poutres en BétonPas encore d'évaluationÉtude de Poteaux et Poutres en Béton30 pages
- Menuiserie NC II : Compétences essentiellesPas encore d'évaluationMenuiserie NC II : Compétences essentielles5 pages
- Dimensionnement sismique d'une villa R+2Pas encore d'évaluationDimensionnement sismique d'une villa R+233 pages
- Classification et caractéristiques des bétonsPas encore d'évaluationClassification et caractéristiques des bétons29 pages
- Devis Forage et Équipement au BéninPas encore d'évaluationDevis Forage et Équipement au Bénin3 pages
- Rapport sur le Dossier Technique en ConstructionPas encore d'évaluationRapport sur le Dossier Technique en Construction18 pages
