Maker Nano RP2040 Interfacing With Maker Line Using Arduino IDE

Introduction

In this tutorial we shall see how to interface Maker Nano RP2040 with Maker Line. This is the continuation from the previous tutorial whereby we have seen how to control the DC motor using the Maker Drive. At the end of the tutorial we shall see how the Maker Line Following Robot function.

Video

Hardware Preparation

Since this is a continuation from the previous tutorial the additional that we will need is the Maker Line.

Hardware Components

Add to Cart

6V 85RPM DC Micro Metal Gearmotor

RM18.50

x 1 unit(s)

Backorder Only

Add to Cart

Maker Drive: Simplifying H-Bridge Motor Driver ...

RM18.00

x 1 unit(s)

Add to Cart

Maker Line: Simplifying Line Sensor For Beginner

RM43.60

x 1 unit(s)

Add to Cart

SPG10/N20 DC Geared Motor Bracket Kit

RM2.90

x 1 unit(s)

Add to Cart

Maker Nano RP2040 Getting Started Kits

RM58.00++

x 1 unit(s)

Building The Circuit

1. Constructing the circuit is pretty much easy since we are using the grove connector. The connection between the devices are done as per the below figure.

Once the connection are made as per the figure above, we can now start to code.

Code

For the code, since we have used different type of devices, please ensure that all the library has been downloaded prior to running this code.

 #include "CytronMotorDriver.h"

 // Maker Line Sensor Pin Connection
#define LINE_D1   6
#define LINE_D2   7
#define LINE_D3   8
#define LINE_D4   9
#define LINE_D5   10


// Configure the motor driver.
CytronMD motor1(PWM_DIR, 2, 3);  // PWM 1 = Pin 2, DIR 1 = Pin 3.
CytronMD motor2(PWM_DIR, 4, 5); // PWM 2 = Pin 4, DIR 2 = Pin 5.


// The setup routine runs once when you press reset.
void setup() {

 pinMode(LINE_D1, INPUT);
 pinMode(LINE_D2, INPUT);
 pinMode(LINE_D3, INPUT);
 pinMode(LINE_D4, INPUT);
 pinMode(LINE_D5, INPUT);

  
}


// The loop routine runs over and over again forever.
void loop() {

  // Perform line following
   int D1 = digitalRead(LINE_D1);
   int D2 = digitalRead(LINE_D2);
   int D3 = digitalRead(LINE_D3);
   int D4 = digitalRead(LINE_D4);
   int D5 = digitalRead(LINE_D5);

   
   
   if (D1==0 && D2==0 && D3==1 && D4==0 && D5==0) {
     motor1.setSpeed(100);   
     motor2.setSpeed(100);    //robot move forward
   }
   else if (D1==0 && D2==1 && D3==0 && D4==0 && D5==0) {
     motor1.setSpeed(50);   
     motor2.setSpeed(100);    //move to left
   }
   else if (D1==1 && D2==0 && D3==0 && D4==0 && D5==0) {
     motor1.setSpeed(0);   
     motor2.setSpeed(100);     //robot slowing down, move more to left
   }
   else if (D1==0 && D2==0 && D3==0 && D4==1 && D5==0) {
     motor1.setSpeed(100);   
     motor2.setSpeed(50);    //move to right
   }
   else if (D1==0 && D2==0 && D3==0 && D4==0 && D5==1) {
     motor1.setSpeed(100);   
     motor2.setSpeed(0);     //robot slowing down, move more to right
   }
   else {
   }
}

Outcome

Just remember to calibrate the maker line before start beginning the line following task.

Thank You

Thanks for reading this tutorial. If you have any technical inquiries, please post at Cytron Technical Forum.

"Please be reminded, this tutorial is prepared for you to try and learn.
You are encouraged to improve the code for a better application."