Conditional Branch Instructions in AVR Microcontroller

Logical Instructions in AVR Microcontroller

Last Updated : 24 Sep, 2020

Logical Instructions are the instructions which perform basic arithmetic operations such as AND, OR, XOR, etc. In AVR micro-controller, the destination operand is always a register.

The following table shows the logical instructions :

Instruction	Operand	Explanation	Example
AND	D, S	D = D AND S Performs a AND operation on the operands and stores the result in the left hand operand	AND D, S
ANDI	D, k(constant)	D = D AND k Performs a AND operation on the operands and stores the result in the left hand operand with the right hand operand being a constant	ANDI D, k
OR	D, S	D = D OR S Performs a OR operation on the operands and stores the result in the left hand operand	OR D, S
ORI	D, k	D = D OR k Performs a OR operation on the operands and stores the result in the left hand operand with the right hand operand being a constant	ORI D, k
EOR	D, S	D = D XOR S Performs a EX-OR operation on the operands and stores the result in the left hand operand	EOR D, S
COM	D.	D = 1’s complement of D The complement action changes ‘1’s to ‘0’s and ‘0’s to ‘1’s	COM D
NEG	D	D = 2’s complement of D This instruction takes the 2’s complement	NEG D
CP	D, S	Compares D and S This instruction is really a subtraction action. The only difference is that the values of registers don’t change	CP D, S
CPI	D, k	Compares D and k The only difference between CP an CPI is that CPI has one of the operands as a constant	CP D, k

Note :
D and S are Destination and Source respectively. Both are registers. k is a constant.

Conditional Branch Instructions in AVR Microcontroller

K

kunalsg18elec

Improve

Article Tags :

Similar Reads

Branch Instructions in AVR Microcontroller

In this article, we will be discussing looping in AVR and branch instructions, both Conditional and Unconditional. Looping in AVR : A repeated operation or a set of instructions is known as a loop in programming. It is one of the most fundamental techniques which comes in very handy in writing code.

Arithmetic instructions in AVR microcontroller

Arithmetic Instructions are the instructions which perform basic arithmetic operations such as addition, subtraction, multiplication, etc. AVR micro-controller has 2 operands which are actually registers that hold the data. The left register is the source register while the right one is the source r

Logical instructions in 8085 microprocessor

Introduction : Logical instructions in the 8085 microprocessor are a set of instructions that perform logical operations on data in registers and memory. Logical operations are operations that manipulate the bits of data without affecting their numerical value. These operations include AND, OR, XOR,

Logical instructions in 8086 microprocessor

Introduction : Logical instructions in the 8086 microprocessor are instructions that perform logical operations on data stored in registers or memory locations. These instructions can manipulate bits within a byte, set or clear individual bits, or perform Boolean operations such as AND, OR, XOR, and

Data Transfer instructions in AVR microcontroller

Data transfer instructions are the instructions that are used to transfer data into micro-controller. These instructions can be used to transfer data from: Register to Register : In register-to-register transfer, data is transfer from one register to another register. Consider an example where you h

CALL Instructions and Stack in AVR Microcontroller

Introduction : The AVR microcontroller is a type of microcontroller developed by Atmel Corporation. It is widely used in various embedded systems due to its low power consumption and high performance. In this context, I will discuss the introduction to CALL instructions and the stack in AVR microcon

Conditional Branch Instructions in AVR Microcontroller

Conditional branch instructions are the set of instructions that is used to branch out of a loop. We will discuss these instructions for the AVR micro-controller. To understand these instructions, first, we need to know about the registers in the AVR micro-controller. Status Register (SReg) : It is

Instruction sets of a microcontroller

Instruction Set: The set of instructions that needs to be executed by a processor in a microcontroller, which defines the fundamental operation of what can be done with this microcontroller. These instructions provide direction to the microcontroller and help it execute functions like data processin

Machine Control Instructions in Microprocessor

Microprocessors are electronic devices that process digital information using instructions stored in memory. Machine control instructions are a type of instruction that control machine functions such as Halt, Interrupt, or do nothing. These instructions alter the different type of operations execute

Arithmetic instructions in 8086 microprocessor

Arithmetic Instructions are the instructions which perform basic arithmetic operations such as addition, subtraction and a few more. Unlike in 8085 microprocessor, in 8086 microprocessor the destination operand need not be the accumulator. Following is the table showing the list of arithmetic instru