Scribd
Upload
505 views1 page

Square Keyway

This document contains Table A2 from Appendix A of Orttech's Pneumatic Installation Guidelines. The table specifies the recommended dimensions in inches for rectangular and square keys used in combination with shafts of various nominal diameters, according to the ANSI B17.1 standard. Notes below the table provide additional details on depth of keyways, tolerances, fits, and that the maximum allowable key size for hubs is specified in Table A1.

Uploaded by

Dan Jeremy
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
505 views1 page

Square Keyway

This document contains Table A2 from Appendix A of Orttech's Pneumatic Installation Guidelines. The table specifies the recommended dimensions in inches for rectangular and square keys used in combination with shafts of various nominal diameters, according to the ANSI B17.1 standard. Notes below the table provide additional details on depth of keyways, tolerances, fits, and that the maximum allowable key size for hubs is specified in Table A1.

Uploaded by

Dan Jeremy
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Orttech

Pneumatic Installation Guidelines, Appendix A

Table A2
Shaft Diameter / Key Combinations Per ANSI B17.1
Dimensions in inches
Nom. Shaft Dia.

Rectangular Key

Square Key

over

to

(width x height)

(width & height)

5/16

7/16

---

3/32

7/16

9/16

1/8 x 3/32

1/8

9/16

7/8

3/16 x 1/8

3/16

7/8

1-1/4

1/4 x 3/16

1/4

1-1/4

1-3/8

5/16 x 1/4

5/16

1-3/8

1-3/4

3/8 x 1/4

3/8

1-3/4

2-1/4

1/2 x 3/8

1/2

2-1/4

2-3/4

5/8 x 7/16

5/8

2-3/4

3-1/4

3/4 x 1/2

3/4

3-1/4

3-3/4

7/8 x 5/8

7/8

3-3/4

4-1/2

1 x 3/4

4-1/2

5-1/2

1-1/4 x 7/8

1-1/4

5-1/2

6-1/2

1-1/2 x 1

1-1/2

6-1/2

7-1/2

1-3/4 x 1-1/2

1-3/4

7-1/2

2 x 1-1/2

11

2-1/2 x 1-3/4

2-1/2

11

13

3x2

13

15

3-1/2 x 2-1/2

3-1/2

15

18

4x3

Please Note:
1. For depth of keyways in the hub and shaft refer to Depth Control Formulas or
Table 3 in the ANSI B17.1 Standard.
2. A minimum headroom clearance of .005 inch is recommended.
3. Recommended tolerance on keyway width is +0 / -.002 inch.
4. Recommended tolerance on key width is +.002 / -0 inch.
5. A tight side to side fit is required between the keys and the shaft and hub keyways.
Hand fitting at assembly is usually required.
6. Key sizes listed in this table are per the ANSI B17.1 standard, maximum allowable
key size for the hub is per Table A1.

igpneu appA

Page A3

Issue date Jan 02

You might also like