Workshop Manual

competence level 3

2011
is n do i cu s al tr m lo ib en w u ed ti o ti sc w n ith i n op yr ou eit ig t o he ht ur r p pr pr rin ot io te ec ra d te o d. gr r ee ele m ct en ro t. ni cf o rm ot

0312 1936 en

Th

Illustrations and data in this workshop manual are subject to technical change in the course of improvements to the engines. Reprinting and reproductions of any kind, even in part, require our written permission.

is

Regarding copyright questions and licensing agreements please contact : VS-DI, Mr. Sonntag Tel.: + 49 (0) 221 822-3053 EMail: [email protected]

Deutz AG Service Information Systems Ottostrae 1 D - 51149 Cologne Tel.: + 49 (0) 221-8 22-0 Fax: + 49 (0) 221-8 22-58 50 http://www.deutz.com Printed in Germany All rights reserved 1st edition, 11/2004 Order No. 0312 1936
11/2004

Workshop Manual 2011

Workshop Manual 2011

Note for printers Color: white Paper: Ikonofix 250 g/m2

0312 1936 en

Workshop Manual

2011

0312 1936 en

Illustrations and data in this workshop manual are subject to technical change in the course of improvements to the engines. Reprinting and reproductions of any kind, even in part, require our written permission.

Deutz AG Service Information Systems Deutz-Mlheimer Strasse 147-149 D - 51063 Kln Tel.: + 49 (0) 221-8 22-0 Fax: + 49 (0) 221-8 22-53 58 http://www.deutz.de Printed in Germany All rights reserved 1st edition, 11/2004 Order No. 0312 1936
11/2004

Contents 2011

Foreword

General

User notes
3.1 3.2 3.2.1 3.2.2 3.3 3.4 3.5 General Specifications Safety regulations and rules for the prevention of accidents Disposal regulations Operating manual and workshop manual Job cards Explanation of symbols

Technical data
4.1 4.2 Test and adjustment data Tightening specifications

Job card overview

5.1 5.2 5.3 Alphabetical sorting Numeric sorting Job card references

Job cards

Commercial tools

Special tools

11/2004

1/2

0312 1651 - 0138

Contents 2011
Notes

11/2004

2/2

0312 1651 - 0138

2011

Foreword
1

11/2004

1/4

0312 1650 - 0138

1 Foreword 2011
Notes

11/2004

2/4

0312 1650 - 0138

1 Foreword 2011
Read and observe the information in this documentation. You will avoid accidents, retain the manufacturers warranty and have a fully functional, ready to use engine at your disposal. This engine is built exclusively for the purpose according to the scope of delivery - defined by the equipment manufacturer (use for the intended purpose). Any use above and beyond this is considered improper use. The manufacturer will not be liable for damages resulting from this. The user will bear the sole risk in this case. Use for the intended purpose also includes observance of the operating, maintenance and repair instructions specified by the manufacturer. The engine may only be used, maintained and repaired by persons who are familiar with it and instructed in the dangers. Make sure that this documentation is available to everyone involved in the operation, maintenance and repair and that they have understood the contents. Failure to observe this documentation can lead to malfunctions and engine damage as well as injury to persons for which the manufacturer will accept no liability. Prerequisite for the proper maintenance and repair is the availability of all necessary equipment, commercial tools and special tools as well as their perfect working order. Engine parts such as springs, clamps, elastic retaining rings etc. constitute an increased risk of injury when not used properly. The pertinent rules for the prevention of accidents and other generally recognized safety and industrial medicine rules must be observed. Maximum cost effectiveness, reliability and long life is only guaranteed when DEUTZ original parts are used. Repair of the engine must comply with use for the intended purpose. Only parts released by the manufacturer for the respective purpose may be used for conversion work. Unauthorized modification to the engine exclude manufacturer liability for resulting damages. Failure to observe this will lead to voiding of the warranty! The engines made by DEUTZ are developed for a wide range of applications. A wide range of variants ensures that the respective special requirements are met. The engine is equipped according to the installation, i.e. not all the parts and components described in this documentation are installed in your engine. We have done our best to clearly identify the differences so that you can easily find the operating, maintenance and repair instructions relevant to your engine.

We are at your service for any questions you may have in this matter. Your DEUTZ AG

11/2004

3/4

0312 1650 - 0138

1 Foreword 2011

11/2004

4/4

0312 1650 - 0138

2011

General
2

11/2004

1/4

0312 1649 - 0138

2 General 2011
Notes

11/2004

2/4

0312 1649 - 0138

2 General 2011
DEUTZ engines are the product of years of research and development. The profound know-how gained in connection with high quality requirements is the guarantee for manufacturing of engines with a long life, high reliability and low fuel consumption. Naturally the high requirements for protection of the environment are also met.

Maintenance and care are decisive for whether the engine satisfactorily meets the set demands. Compliance with the prescribed maintenance times and the careful execution of maintenance and care are therefore essential. Difficult operating conditions deviation from normal operation must be observed especially.

DEUTZ AG Please consult one of our service representatives responsible for operating faults and spare parts questions. Our trained specialist personnel ensures fast, professional repairs using original parts in the event of damage. Original parts of the DEUTZ AG are always produced according to the latest state of the art. Information about our service can be found at the end of this documentation.

Take care when the engine is running Only perform maintenance work or repairs when the engine is at a standstill. Replace any removed protective devices upon completion of the work. When working on the running engine, work clothing must be close fitting.

Safety
!

This symbol accompanies all safety notes. Observe these carefully. Also pass on the safety instructions to your operating personnel. The General safety regulations and rules for the prevention of accidents of the legislator must be observed additionally.

Note
This symbol accompanies information of a general kind. Observe these carefully.

Asbestos
Gaskets used in this engine are asbestos-free. Please use the appropriate spare parts for maintenance and repair work.

11/2004

3/4

0312 1649 - 0138

2 General 2011
Notes

11/2004

4/4

0312 1649 - 0138

2011

User notes
3

11/2004

1/8

0312 1648 - 0138

3 User notes 2011

Notes

11/2004

2/8

0312 1648 - 0138

3 User notes 2011

3.1 General
The maintenance work prescribed in the operating manual and in the workshop manual must be performed on schedule and completely. The maintenance personnel must possess the necessary technical knowledge to perform the work. Safety and protection devices which are removed during maintenance work must be replaced again afterwards.

Caution!
!

The rules for the prevention of accidents and the safety regulations must be observed during maintenance work.

Also observe the special safety regulations for the different maintenance groups which are listed in detail as job cards in the Job cards chapter (cf. also section 1.2). See the maintenance schedules for the maintenance intervals. These also inform you of the work to be performed. The job cards provide technical instructions for performing the work.

3
3.2
3.2.1

Specifications
Safety regulations and rules for the prevention of accidents

For various maintenance groups, detailed safety notes in the form of job cards have been compiled, these precede the job cards of the respective maintenance groups. The legally prescribed rules for the prevention of accidents (available from professional associations or from dealers) must be observed. These are dependent on the installation site, operating mode and the operating and auxiliary materials being used. Special protection measures depending on the respective work are specified and identified in the job description. It generally applies among other things: for the personnel - Only instructed personnel may operate or maintain the engine. Unauthorized persons may not enter the engine room. - Wear close fitting clothing and ear protectors in the engine room when the engine is running. - Only appoint qualified personnel to do repairs and maintenance. for the engine room: Ensure adequate ventilation (do not cover air shafts) Install first aid kit and suitable fire extinguishers. Check the filling and readiness for operation regularly. Only store inflammable materials in the engine room if these are necessary for operating the system. Smoking and naked lights are prohibited in the engine room.

For operation and maintenance of the engine: - Only start the engine when all protection devices are installed. Make sure that no-one is standing in the danger area. - Only perform cleaning, maintenance and repair work when the engine has been shut down and secured against starting.

!
3/8

11/2004

0312 1648 - 0138

3 User notes 2011

3.2.2 Disposal regulations
The work described in the operating manual and workshop manual necessitates renewal of parts and operating materials. The renewed parts / operating materials must be stored, transported and disposed of properly. The owner himself is responsible for this. Disposal includes recycling and the scrapping of parts / operating materials whereby recycling has priority. Details of disposal and their monitoring are governed by regional, national and international laws and directives which the system operator must observe on his own responsibility.

3.3

Operating manual and workshop manual

To structure the information to suit the user, the service documentation is divided into operating manual and workshop manual. The operating manual contains a general description and instructions for all other maintenance work. It contains the following chapters: 1. General, Contents 2. Engine description 3. Operation 4. Operating materials 5. Maintenance 6. Care and maintenance work 7. Faults, causes and remedies 8. Engine corrosion protection 9. Technical data 10. Service The workshop manual assumes knowledge of the contents of the operating manual, this applies especially for the safety regulations. Minor repairs and emergency measures on components are described the execution of which requires more effort and appropriately qualified personnel.

11/2004

4/8

0312 1648 - 0138

3 User notes 2011

3.4 Job cards
The job cards are divided into job cards of the workshop manual e. g. W 04-05-01 and the maintenance manual I 04-05-01.

Numbering of job cards

Dokumentationsart Der fhrende Buchstabe steht fr die Art der Dokumentation. W = Werkstatthandbuch I = Instandsetzungsanleitung

Instandhaltungsgruppe (fr alle Motoren gleich) 00 01 02 03 04 05 06 Allgemein / bergreifende Ttigkeiten Zylinderkopf Triebwerk Kurbelgehuse Motorsteuerung Drehzahlregelung Abgasanlage / Aufladung 07 08 09 10 11 12 13 Kraftstoffsystem Schmierlsystem Khlflssigkeitssystem Druckluftsystem berwachungssystem Sonstige Bauteile Elektrische Anlage

Teilsystem (Bauteil) Die Teilsysteme unterscheiden sich je Instandhaltungsgruppe. Allgemein gltig: 00 Teilsysteme-bergreifend bzw. Sicherheitsvorschriften (SV) 01 Systemparameter bzw. generelle Kontrollen

Fortlaufende Nummer Zhlend je Teilsystem (Bauteil) Verschiedene Ttigkeiten je Teilsystem (Bauteil) Versions-Unterschiede

W 03-03-03
80301 3

11/2004

5/8

0312 1648 - 0138

3 User notes 2011

Structure of a job card

Kurbelgehuse W 00-00-00

13 12 11 6 5

3
10 6

8
39744 1

1. DEUTZ, publisher of the service documentation 2. Engine type (e. g. 914) 3. Maintenance group 4. Job card number 5. Reference to other job cards, Specifications and similar 6. Explanatory graphics 7. Page number

8. DEUTZ-internal part number of job card and technical order number 9. Date of issue of the job card 10. Work sequence 11. Safety and general notes 12. Necessary tools, auxiliary materials and spare parts 13. Title of the job card

Note
For inquiries about the job card please always state the engine type (2), the job card number (4), the page number (7), the date of issue (9) or alternatively the DEUTZ-internal part number (8).

11/2004

6/8

0312 1648 - 0138

3 User notes 2011

3.5 Explanation of symbols
Caution!
!

Auxiliary material
For example: Lifting gear, adhesive

Tools
for example:100 400 - meter

3
Note
For example: Cylinder head is dismantled.

Always renew when assembling

For example: Gaskets

References
For example: Job card no. W xx-yy-zz

01 61

See technical data (test and setting data)

Line note, for example: 01 61 Valve clearance (inlet)

01001

See technical data (tightening specifications)

Line note, for example: 01001 Cylinder head on crankcase

11/2004

7/8

0312 1648 - 0138

3 User notes 2011

Notes

11/2004

8/8

0312 1648 - 0138

2011

4
4.1

Technical data
Test and adjustment data

11/2004

1/22

0312 1642 - 0138

4 Technical data
4.1 Test and adjustment data Notes

2011

11/2004

2/22

0312 1642 - 0138

4 Technical data 2011

00 00
ID No. 00 04

4.1 Test and adjustment data

Engine general
Name Engine weight according to DIN 70020-A Remark F2L engine F3L engine F4L engine F2M engine F3M engine F4M engine BF3L engine BF4L engine BF3M engine BF4M engine Value 175 217 256 169 210 kg 248 222 257 215 250 four-stroke diesel Direct injection Diameter 94 112 FL/M engines BFL/M engines 19:1 17.5:1 left 25 to 30 22 to 27 180 120 bar bar mm mm Unit

00 10 00 20 00 31 00 32 00 40

Working principle Combustion process Bore Stroke Compression ratio

00 50

Direction of rotation

looking onto the flywheel FL/M engines BFL/M engines

00 51

Compression pressure

00 70

Ignition distance

2 and 4 cylinder 3-cylinder

11/2004

3/22

0312 1642 - 0138

4 Technical data
4.1 Test and adjustment data
ID No. 00 71

2011
Remark 2-cylinder 3-cylinder 4-cylinder Value 1-2 1-2-3 1-3-4-2 Unit

Name Ignition sequence

00 81

Cylinder arrangement 2-cylinder A = Manifold side B = Operating side

A
1 2

4
Cylinder arrangement 3-cylinder A = Manifold side B = Operating side

39617 0

A
1 2 3

B
Cylinder arrangement 4-cylinder A = Manifold side B = Operating side

39618 0

A
1 2 3 4

39619 0

01 00
ID No. 01 01 01 02 01 03 01 04

Cylinder head
Name Bore diameter for valve seat ring (inlet) Bore diameter for valve seat ring (outlet) Bore diameter for valve seat ring (inlet) Bore diameter for valve seat ring (outlet) Additional information Standard Standard 1. Overmeasure step 1. Overmeasure step Value 42.590 - 42.615 36.010 - 36.015 42.800 - 42.825 37.200 - 37.225 Unit mm mm mm mm

11/2004

4/22

0312 1642 - 0138

4 Technical data 2011

ID No. 01 05 01 06 Name Bore diameter for valve guide Bore diameter for valve guide

4.1 Test and adjustment data

Additional information Standard 1. Overmeasure step Repair Fit H7 Standard Undermeasure

Value 8.000 - 8.025

Unit mm

12.000 - 12.018

mm

01 08 01 09 01 10 01 12

Height of cylinder head Height of cylinder head Valve guide External diameter of the valve guide

118.00 0.1 117.96 0.1

mm mm

1. Overmeasure step Repair Repair Fit E7

12.025 - 12.035

mm

01 16

Internal diameter of valve guide (inlet)

8.025 - 8.040 8.025 - 8.040

mm

01 17

Internal diameter of valve guide (outlet) Repair Fit E7 Valve seat ring External diameter of the valve seat ring (inlet) External diameter of the valve seat ring (outlet) External diameter of the valve seat ring (inlet) External diameter of the valve seat ring (outlet) External diameter of the valve seat ring (inlet) External diameter of the valve seat ring (outlet) Valve Valve shaft diameter (inlet) Standard Standard

mm

01 20 01 21

42.680 0.006

mm

01 22

Standard

37.075 0.006

mm

01 23

Repair standard

42.67 0.005

mm

01 24

Repair standard

37.07 0.005

mm

01 27

1. Overmeasure step

42.87 0.005

mm

01 28

1. Overmeasure step

37.27 0.005

mm

01 30 01 31

7.98

-0.015

mm

11/2004

5/22

0312 1642 - 0138

4 Technical data
4.1 Test and adjustment data
ID No. 01 32

2011
Additional information Value Unit

Name Valve shaft diameter (outlet)

Standard Wear limit Wear limit Wear limit FL/M engines Wear limit BFL/M engines

7.96 0.5 1.3 0.8

-0.015

mm mm mm mm

01 33 01 34 01 35

Valve shaft clearance (inlet) Valve shaft clearance (outlet) Valve edge strength on valve head (inlet)

1.4

mm

01 36

Valve edge strength on valve head (outlet)

Wear limit FL/M engines Wear limit BFL/M engines

1.2

mm

1.2 41.5 0.1 35.4 0.1

mm mm mm

01 37 01 38 01 40 01 41

Valve head diameter (inlet) Valve head diameter (outlet) Valve seat Valve seat width on valve seat ring (inlet) FL/M engines B/FL/M engines

1.7 0.4 1.58 0.4 1.7 0.4 1.7 0.4 1.53

mm mm mm mm mm

01 42

Valve seat width on valve seat ring (outlet)

FL/M engines B/FL/M engines

01 45

Valve lag dimension (inlet)

Wear limit FL/M engines Wear limit B/FL/M engines

1.3

mm

01 46

Valve lag dimension (outlet)

Wear limit FL/M engines Wear limit B/FL/M engines

1.53

mm

1.3

mm

11/2004

6/22

0312 1642 - 0138

4 Technical data 2011

ID No. 01 47 Name Valve seat angle (inlet)

4.1 Test and adjustment data

Additional information FL/M engines B/FL/M engines

Value 45 30 45 45

Unit

01 48

Valve seat angle (outlet)

FL/M engines BFL/M engines

01 50 01 51

Valve spring Valve spring length (unclamped normal) Wire diameter 3.35 mm Wire diameter 3.40 mm 38.9 39.3 mm mm

01 60 01 61

Valve clearance Valve clearance (inlet) after a cooling time of at least 0.5 h (oil temperature < 80 C) Test and setting values in inspections from a running time of 50 operating hours of the engine or life of the cylinder head gasket (see maintenance schedule) Setting values when changing the cylinder head gasket

0.3 0.05

mm (0.4 0.05)

01 62

Valve clearance (outlet)

after a cooling time of at least 0.5 h (oil temperature < 80 C) Test and setting values in inspections from a running time of 50 operating hours of the engine or life of the cylinder head gasket (see maintenance schedule) Setting values when changing the cylinder head gasket

0.5 0.05

mm (0.6 0.05)

11/2004

7/22

0312 1642 - 0138

4 Technical data
4.1 Test and adjustment data
ID No. 01 63

2011
Additional information Value Unit

Name Valve clearance setting scheme

Turn over engine up until reaching the valve overlap cyl. no. 1.

Note
According to the order below (see table) the valve clearance setting is possible with 2 crankshaft revolutions 360. Crankshaft setting 1 Cyl. no. 1 = overlap

4
Crankshaft setting 2 Turn the crankshaft one rev on (360).

white = not adjustable black = adjustable

white = not adjustable black = adjustable

11/2004

8/22

0312 1642 - 0138

4 Technical data 2011

ID No. 01 70 01 72 Name toggle lever / toggle lever block toggle lever bore for toggle lever axle (outlet) toggle lever bore for toggle lever axle (inlet) diameter of the toggle lever axle Roughness of the sealing surface Length of the cylinder head screw Standard 18 0.27 mm

4.1 Test and adjustment data

Additional information

Value

Unit

01 73

18 0.27 17.97 0.01 15 - 18 150.000 - 0.8

+ 0.8

mm mm Rz mm

01 74 01 93 01 98

02 00
ID No. 02 02 02 03 02 04

Drive system
Name Main bearing pin Diameter of the main bearing pin Undermeasure graduation for main bearing pin Standard 1. Stage 2. Stage 69.970 - 69.990 0.25 0.50 69.47 Wear limit Standard 0.008 58
+4

Additional information

Value

Unit

mm mm mm mm mm HRC

02 05

Limit value for undermeasure graduation of the main bearing pin Unroundness of the main bearing pin Surface hardness of the main bearing pin Fit bearing pin Width of fit bearing pin Undermeasure graduation for fit bearing pin Limit value for undermeasure graduation of the fit bearing pin (width) 1. Stage

02 06 02 07

02 10 02 11 02 12

35 +0.04 0.4

mm mm

02 13

35.44

mm

11/2004

9/22

0312 1642 - 0138

4 Technical data
4.1 Test and adjustment data
ID No. 02 20 02 21 02 22 02 23 Lifting journal Width of lifting bearing journal Diameter of the lifting bearing journal Undermeasure step for lifting bearing journal Stroke 112 mm 1. Stage 2. Stage 02 24 Limit for undermeasure step of the lifting bearing journal Unroundness of the lifting bearing journal Concentricity of the crankshaft Hollow throat radius lifting and main bearing journal Wear limit max. deviation Do not damage hollow throat when reworking! Stroke 112 mm 31 +0.2 54.970 - 54.990 0.25 mm 0.50 54.47 mm mm mm

2011
Additional information Value Unit

Name

02 25

0.01 0.05

mm mm

02 26 02 27

1.9

+ 0.5

mm

02 30 02 31

Crankshaft main bearing Internal diameter of the main bearing shells Undermeasure graduation for main bearing shells Standard 1. Stage 2. Stage 70.020 - 70.055 0.25 mm 0.50 0.100 - 0.273 0.4 2.4
+ 0.05

mm

02 32

02 34

Axial clearance of crankshaft

Standard Wear limit

mm mm mm

02 35

Strength of the starting rings

Standard

02 36

Strength of the starting rings

1. Overmeasure step

2.6

+ 0.05

mm

02 40 02 41

Con-rod Parallelism of the con rod to the piston bolt at a distance of 100 mm 0.03 mm

11/2004

10/22

0312 1642 - 0138

4 Technical data 2011

ID No. 02 42 Name Parallelism of the con rod to the piston bolt

4.1 Test and adjustment data

Additional information at a distance of 100 mm max. perm. deviation

Value

Unit

0.03

mm

02 43

Internal diameter of the piston bolt bush Standard FL/M engines Standard BFL/M engines

26.025 - 26.035 mm 30.025 - 30.035

02 45

Theoretical clearance between Piston bolt bush (con rod) and piston bolt Clearance between piston and piston bolt Con rod bearing Internal diameter of the con rod bearing shells (in installed state) Limit value for undermeasure graduation of the con rod bearing shells Undermeasure graduation of the con rod bearing Con rod bearing bore in con rod Theoretical clearance between the con rod bearing and the lifting journal Con rod bearing clearance Piston bolt Diameter of the piston bolt

Wear limit

0.08

mm

02 48

Wear limit

0.004 - 0.015

mm

02 50 02 52

55.024 - 55.055

mm

02 53

54.524 - 54.555

mm

02 54

0.25 58.500 - 58.520 0.014 - 0.07 Wear limit 0.12

mm mm mm mm

02 55 02 56

02 57 02 60 02 61

FL/M engines BFL/M engines

25.995 - 26.000 mm 29.995 - 30.000 0.025 - 0.04 mm

02 62

Piston bolt clearance between con rod and piston bolt Piston

02 70

11/2004

11/22

0312 1642 - 0138

4 Technical data
4.1 Test and adjustment data
ID No. 02 71

2011
Additional information Measuring point 1 at height 22 mm FL/M engines Measuring point 1 at height 25 mm BFL/M engines Measuring point 1 at height 25 mm BFL engines without cooling duct Value Unit

Name Diameter of the piston

93.920

93.900

mm

93.880

02 72

Diameter of the piston

Measuring point 2 at height 44.5 mm FL/M engines Measuring point 2 at height 47 mm BFL/M engines Measuring point 2 bat height 47 mm BFL engines without cooling duct

93.856

93.840

mm

93.820

02 73

Diameter of the piston

Measuring point 3 at height 69.7 mm FL/M engines Measuring point 3 at height 66.5 mm BFL/M engines Measuring point 3 at height 66.5 mm BFL engines without cooling duct

93.670

93.720

mm

93.700

02 74 02 75 02 76 02 77

Overmeasure graduation Piston overlap for cylinder head gasket Piston overlap for cylinder head gasket Piston overlap for cylinder head gasket 1 Notch 2 Notches 3 Notches

0.5 0.514 - 0.69 0.691 - 0.76 0.761 - 0.83

mm mm mm mm

11/2004

12/22

0312 1642 - 0138

4 Technical data 2011

ID No. 02 78 Piston bolt bore Name

4.1 Test and adjustment data

Additional information FM engines BFL/M engines

Value 26.004 - 26.010 30.004 - 30.010

Unit mm mm

20 79

Determine piston class

Piston class A Stroke 112 mm only in FL/M engines Piston class B Stroke 112 mm only in FL/M engines

196.380 - 196.490

mm

196.491 - 196.690

mm

02 80 02 81

Piston rings Piston ring 1st ring Rectangular ring External diameter/ internal diameter x height FL/M engines External diameter/ internal diameter x height BF3/4L/M engines External diameter/ internal diameter x height External diameter/ internal diameter x height

4
94.0 x 2.0 x 3.9 mm

Piston ring 1st ring Double-sided trapezoidal ring

94.0 x 3.0 x 3.9

02 82

Piston ring 2 ring minute ring

94.0 x 1.99 x 4.05 mm 91.0 x 2.5 x 3.8

02 83

Piston ring 3 ring Roof chamfer ring

External diameter/ internal diameter x height External diameter/ internal diameter x height Double-sided trapezoidal ring Wear limit Rectangular ring Wear limit

94.0 x 3.0 x 3.73 mm

Piston ring 3 ring Oil slit ring

94.0 x 2.99 x 2.9

02 84

Piston ring joint clearance of the 1st piston ring BFL/M engines Piston ring joint clearance of the 1st piston ring FL/M engines

0.3 - 0.5 mm 0.3 - 0.5 0.8

11/2004

13/22

0312 1642 - 0138

4 Technical data
4.1 Test and adjustment data
ID No. 02 85

2011
Additional information minute ring Wear limit Roof chamfer ring Wear limit FL/M engines Oil slit ring B/FL/M engine Value 1.5 - 2.0 mm 2.5 0.4 - 0.7 1.2 Unit

Name Piston ring joint clearance of the 2nd piston ring B/FL/M engines Piston ring joint clearance of the 3rd piston ring

02 86

mm

0.3 - 0.6

02 87

Axial clearance of the 1st piston ring Rectangular ring Axial clearance of the 1st piston ring

Wear limit FL/M engines Wear limit BFL/M engines

0.2 Trapezoidal groove wear gauge contact with piston 0.2 0.15 1.975 - 1.990 mm 3.0 1.975 - 1.990 2.975 - 2.990 mm mm mm

02 88 02 89 02 91

Axial clearance of the 2nd piston ring Axial clearance of the 3rd piston ring Piston ring height 1st. piston ring

Wear limit Wear limit Rectangular ring Double-sided trapezoidal ring

mm mm

02 92 02 93

Piston ring height 2nd piston ring Piston ring height 3rd piston ring

minute ring Roof chamfer ring Wear limit Oil slit ring Wear limit

2.975 - 2.990

02 95

Position of the piston ring joints

Angle of twist to each other Angle of twist of spring joint to piston ring joint Piston class A Piston class B

90 - 120

02 96

Position of the piston ring joints roof chamfer ring Compression height

180 51.67 51.77

mm mm

20 97

11/2004

14/22

0312 1642 - 0138

4 Technical data 2011

ID No. 02 99 Name Piston ring height 3rd piston ring

4.1 Test and adjustment data

Additional information Roof chamfer ring

Value 2.975 - 2.990

Unit mm

03 00
ID No. 03 10 03 11

Crankcase
Name Camshaft bearings Bore diameter for camshaft bearing liner in crankcase External diameter of the camshaft bearing liner Internal diameter of the camshaft bearing liner Camshaft bearing liner Bore for camshaft main bearing Diameter of the main bearing bore Standard Fit H6 75.000
+0.019

Additional information

Value

Unit

Fit H7

58

+0.030

mm

03 12

Standard

58.075

+0.045

4
mm mm mm

03 13

in the installed state Wear limit

54.000 - 54.054 54.08

03 14 03 20 03 21

mm

03 27

Fit bearing width on crankcase

30 - 0.033

mm

03 30 03 31

Cylinder Bore diameter of the cylinder Standard Wear limit Overmeasure step Wear limit of the overmeasure step 94.000 94.1 94.500
+ 0.020 + 0.020

mm mm mm

03 32 03 41

Bore diameter of the cylinder Bore diameter of the cylinder

03 42

Bore diameter of the cylinder

94.6

mm

11/2004

15/22

0312 1642 - 0138

4 Technical data
4.1 Test and adjustment data
04 00
ID No. 04 10

2011

Engine control
Name Control times for 1 mm valve clearance Inlet opens after UT Inlet closes after LT Outlet opens before LT Outlet closes before UT Camshaft Cam stroke (inlet) Cam stroke (outlet) Diameter of the camshaft bearing pin Standard 6.6 0.08 6.8 0.08 53.045 - 53.060 mm mm mm 312 1648 2748 412 Additional information Value Unit

04 11 04 12 04 13 04 14

04 20 04 21 04 22 04 31

05 00
ID No. 05 00 05 04 05 05 05 06 05 41

Speed governing
Name Speed governing Setting screw for full load stop Setting screw for minimum speed Screw in depth of the adapter capsule Full load stop (charge pressuredependent) in fuel filter console Stop screw 12 0.5 23 0.1 6.4 0.5 18 1 mm mm mm mm Additional information Value Unit

11/2004

16/22

0312 1642 - 0138

4 Technical data 2011

07 00
ID No. 07 01 07 02 07 10 Pump Make/Type injection pump no specification

4.1 Test and adjustment data

Fuel system
Name Additional information Value Unit

Note
Only injection pumps with the same classification may be installed per engine. 07 11 Make/Type (Motorpal) PCIM9F2071 PCIM9F2073 Make/Type (Bosch) PF 30 V, see rating plate PF 30 V, see rating plate

11/2004

17/22

0312 1642 - 0138

4 Technical data
4.1 Test and adjustment data
ID No. 07 16

2011
Additional information Color marking: black Camshaft stroke 11.0 mm FL/M engine Color marking: green Camshaft stroke 11.0 mm BFL/M engine Color marking: blue Camshaft stroke 11.0 mm FL/M engine Color marking: red Camshaft stroke 11.0 mm BFL/M engine Color marking: green Camshaft stroke 11.7 mm BFL/M engine Color marking: red Camshaft stroke 11.7 mm BFL/M engine Value Unit

Name Injection pump length "X" Standard roller tappet Motorpal TN 0428 1810 Injection pump length "X" Standard roller tappet Motorpal TN 0428 1814 Injection pump length "X" Hydro-roller tappet Motorpal TN 0428 6791 Injection pump length "X" Hydro-roller tappet Motorpal TN 0428 6450 Injection pump length "X" Standard roller tappet Motorpal TN 0428 6681 Injection pump length "X" Hydro-roller tappet Motorpal TN 0428 6792

60.9

mm

60.9

mm

52.1

mm

07 17

52.1

mm

61.6

mm

52.8

mm

Classification of the injection pump

A B C D 11.0 11.7 mm mm

07 19

Camshaft stroke for injection pump

11/2004

18/22

0312 1642 - 0138

4 Technical data 2011

ID No. 07 21 Name Selection of the shim gasket Determined difference (Ss) up to 0.37 0.38 0.42 0.43 0.47 0.48 0.52 0.53 0.57 0.58 0.62 0.63 0.67 0.68 0.72 0.73 0.77 0.78 0.82 0.83 0.87 0.88 0.92 0.93 0.97 0.98 1.02 1.03 1.07 1.08 1.12 1.13 1.17 1.18 1.22 1.23 1.27 1.28 1.32 Dimension "a" of the identification 9 14 12 17 15 20 18 23 21 26 24 8 27 11 30 29 33 7 10 13 mm

4.1 Test and adjustment data

Additional information

Value

Unit

Part number

0417 8522 0428 6587 0417 8523 0428 6588 0417 8524 0428 6589 0417 8525 0428 6590 0417 8526 0428 6591 0417 8527 0428 1633 0417 8528 0428 1634 0427 2923 0428 6592 0427 2924 0428 6593 0428 1635 0428 6696

11/2004

19/22

0312 1642 - 0138

4 Technical data
4.1 Test and adjustment data
ID No. 07 31 07 50 07 51

2011
Additional information Value see company plate Unit

Name Beginning of pumping Injection valve Nozzle type

Bosch FL engines Bosch BFL engines Motorpal (leak oil-less) B/FL engines

DSLA 144 P547 5-hole DLLA 144 P521 5-hole DOP152P522 3898 170
+10

07 52

Nozzle opening pressure of the injection valve (leak oil-less) Motorpal

bar

17 07 53 Pressure for leak test of the injection valve below the previously read opening pressure

+1

MPa

20

bar

08 00
ID No. 08 10 08 41

Lube oil system

Name Lube oil pump Pressure limiting valve Standard without cabin heater connection Pressure limiting valve with cabin heater connection Opening pressure Color marking Opening pressure Color marking 3.0 green 1.0 yellow 1.7 red 0.3 blue bar bar bar bar Additional information Value Unit

08 42

Pressure limiting valve Cabin heater connection

Opening pressure Color marking

08 43

Pressure limiting valve Cabin heater connection Engine input

Opening pressure Color marking

11/2004

20/22

0312 1642 - 0138

4 Technical data 2011

ID No. 08 44 Name Length of the compression spring (green) for the oil pressure regulating valve Length of the compression spring (yellow) for the oil pressure regulating valve 08 45 Length of the compression spring (red) for the oil pressure regulating valve Length of the compression spring (blue) for the oil pressure regulating valve Lube oil pressure Lube oil pressure in low idle Oil temperature approx. 110 C Starts opening Fully open 08 74 Length of the compression spring for the lube oil thermostat 1.4 93 C 110 116.7 mm bar

4.1 Test and adjustment data

Additional information

Value

Unit

without heater connection

56.5

mm

with heater connection

80.5

mm

with heater connection

78.4

mm

08 46

with heater connection

61.8

mm

08 50 08 51

08 73

Lube oil thermostat

09 00
ID No. 09 91

Cooling system
Name Gap dimension between running wheel and blower jacket inlet Additional information Value min. = 0.2 max. = 0.8 Unit

mm

12 00
ID No. 12 11 12 21

Other components
Name Tension of the single V-belt Tension of the single V-belt Additional information First assembly Check after 15 min running under load Value 450 50 300 20 Unit N N

11/2004

21/22

0312 1642 - 0138

4 Technical data
4.1 Test and adjustment data Notes

2011

11/2004

22/22

0312 1642 - 0138

2011

4
4.2

Technical data
Tightening specifications

11/2004

1/14

0312 1643 - 0138

4 Technical data
4.2 Tightening specifications Notes

2011

11/2004

2/14

0312 1643 - 0138

4 Technical data 2011

00000 Engine general
Pretightening value 90 Nm 90 Nm Re-tightening value

4.2 Tightening specifications

ID no.

Name

Remark

00001 Clamp holder on crankcase 00002 Clamp holder on adapter for assembly block 00003 Engine mount on crankcase elast. mounting

180 Nm

+ 30

11/2004

3/14

0312 1643 - 0138

4 Technical data
4.2 Tightening specifications
01000 Cylinder head
Pretightening value Re-tightening value

2011

ID no.

Name

Remark

01001 Cylinder head on crankcase 30 Nm

+ 80 Nm + 160 Nm + 90

In case of provability use max. 5 times. oil lubricated See tightening order

Tightening order 2-cylinder

4 2 6

4
Tightening order 3-cylinder

39152 1

39153 1

Tightening order 4-cylinder

8 6 4 5 9

10

39154 1

01002 Toggle lever block on cylinder head 01003 Lock nut on valve setting screw 01004 Cylinder head cover on cylinder head

21 Nm 20 2 Nm 8.5 Nm

11/2004

4/14

0312 1643 - 0138

4 Technical data 2011

02000 Drive system
Pretightening value Re-tightening value

4.2 Tightening specifications

ID no.

Name

Remark

02010 Main and fit bearing covers on crankcase

50 Nm

+ 60 + 45

in case of provability use max. 3 times with lube oil Central screw tighten alternately in case of provability use max. 5 times in case of provability use max. 5 times

02015 Crankshaft gear wheel/flange hub on crankshaft 02020 Con rod bearing cover on con rod (crack con rod)

130 Nm

+ 210

30 Nm

+ 60 + 60 + 60 + 60

Con rod bearing cover on con rod

30 Nm

03000 Crankcase
Pretightening value Re-tightening value

ID no.

Name

Remark

03003 Locking screw on crankcase 18 2 Nm

Setting bolt for crankshaft lock Holder for setting bolt for crankshaft lock Renew CU sealing ring Setting bolt for control linkage lock Holder for setting bolt for control linkage lock Renew CU sealing ring

03004 Locking screw on crankcase 18 Nm

11/2004

5/14

0312 1643 - 0138

4 Technical data
4.2 Tightening specifications
Pretightening value Re-tightening value

2011
Remark

ID no.

Name

03007 Locking screws M18 x 1.5mm - item 5 Note installation position of the sealing ring! Always renew after disassembly. M12 x 1.5mm - item 6 M30 x 1.5mm - item 7 Always renew after disassembly.

50 Nm

26 Nm

95 Nm

M20 x 1.5mm - item 10 Always renew after disassembly. M18 x 1.5mm - item 15 Always renew after disassembly. 03010 Rear cover on crankcase 03020 Front cover on crankcase 03030 Oil tray (plate), 2, 3 and 4-cylinder,

56 Nm
33822 1

50 Nm

21 Nm 21 Nm 0.5 Nm 21 Nm

Note tightening order! Note tightening order! Screws M8 x 16 mm Note tightening order! Screws M8 x 30 mm Note tightening order! Screws M8 x 5 mm Note tightening order! Cylinder head bolts Note tightening order! oiled Renew CU sealing ring

Oil tray (cast), 4-cylinder

0.5 Nm

31 Nm

Oil tray (cast), 4-cylinder

0.5 Nm

21 Nm

Oil tray (cast), 4-cylinder

0.5 Nm

180 Nm

03031 Oil drain screw on lube oil tray

55 5 Nm

03060 Crankcase bleeding on: Front cover Cylinder head cover Cylinder head

8.5 Nm

11/2004

6/14

0312 1643 - 0138

4 Technical data 2011

ID no. Name Pretightening value

4.2 Tightening specifications

Re-tightening value

Remark

03081 Connection housing on crankcase

106 Nm

M12 x 20mm M12 x 30mm M12 x 35mm M12 x 55mm M12 x 70mm M12 x 75mm M12 x 95mm

03082 Connection housing on crankcase Connection housing on crankcase

180 Nm

M14 x 55mm M10 x 40mm M10 x 30mm M10 x 25mm hex

45 Nm

Connection housing on crankcase

60 Nm

M10 x 40mm Cylinder head bolts M8 x 10mm M8 x 30mm M8 x 50mm

Connection housing on crankcase 22 Nm

03085 Cap on connection housing Cover plate on connection housing

9 Nm 9 Nm

04000 Engine control

Pretightening value 30 Nm 21 Nm 21 Nm Note tightening order! Note assembly specification! Re-tightening value

ID no.

Name

Remark

04001 Camshaft toothed belt wheel on camshaft 04002 Start-up disc on camshaft 04052 Clamping roller on front cover

+ 210

Central screw

04053 Protective hood (toothed belt) on front cover

7 Nm

11/2004

7/14

0312 1643 - 0138

4 Technical data
4.2 Tightening specifications
05000 Speed governing
Pretightening value 9.2 Nm 6 0.6 Nm 16 1.6 Nm 4.5 Nm 6 0.6 Nm 8.5 Nm Re-tightening value

2011

ID no.

Name

Remark

05004 Lock nut on setting screw 05005 Lock nut on setting screw 05006 Lock nut on setting screw 05007 Lock nut on setting screw 05008 Lock nut on setting screw 05011 Speed governor on connection housing

Full load stop Minimum speed Screw spring pre-tension Shutoff stop Adapter capsule

05021 Regulator lever shaft on front cover 05022 No load capsule on front cover 05023 Adapter capsule on front cover 05024 Eccenter shaft on front cover 05025 Cap (speed adjustment lever) on front cover

9.2 Nm 4.6 0.4 Nm 10 1 Nm 10 1 Nm Lock nut

4.5 Nm Valve crankshaft housing bleeding on front cover 05041 Lifting magnet (shutoff magnet) on front cover 05065 Lifting magnet (start volume release) on front cover 8.5 Nm

10 Nm

06000 Exhaust system / Charging

Pretightening value 55 Nm 21 Nm 4 1 Nm Re-tightening value

ID no.

Name

Remark

06001 Exhaust manifold on cylinder head 06020 Turbocharger on exhaust manifold 06024 Reducer on turbocharger

with DEUTZ S1 with DEUTZ S1 Hose clip

11/2004

8/14

0312 1643 - 0138

4 Technical data 2011

ID no. Name Pretightening value 21 Nm 21 Nm 10 Nm

4.2 Tightening specifications

Re-tightening value

Remark

06030 Air intake pipe on cylinder head Charge air on cylinder head 06094 Solenoid valve on LDA

07000 Fuel system

Pretightening value 21 Nm 35 5 Nm Motorpal Re-tightening value

ID no.

Name

Remark

07001 Injection valve on cylinder head 07002 Injection nozzles lock nut on nozzle holder (leak oil-less) Injection nozzles lock nut on nozzle holder 07003 Injection line on: Injection valve injection pump 07012 Injection pump on (Bosch/ Motorpal) crankcase 07015 Fuel supply line to injection pump

45 5 Nm

Bosch

25 2.5 Nm

Union nut

21 Nm Hollow screw DIN 7643-8 Piston pump Diaphragm pump Renew CU sealing rings Hollow screw

29 Nm

07024 Fuel pump on crankcase

21 Nm

07061 Overcurrent line to injection pump

29 Nm

07062 Overcurrent line to cylinder head bolt 07071 Locking screw on injection pump (Motorpal) 07082 Fuel filter console on crankcase 07087 Fuel filter console on holder

8.5 Nm

45 5 Nm 21 Nm

Renew CU sealing rings

Hexagon bolt M8 x 50mm and hexagon nut M8 27 Nm

11/2004

9/14

0312 1643 - 0138

4 Technical data
4.2 Tightening specifications
Pretightening value 22 Nm Re-tightening value

2011
Remark

ID no.

Name

07095 Charge pressure-dependent full load stop (LDA) on crankcase 07096 Cap on charge pressuredependent full load stop (LDA) 07099 Fuel filter on fuel filter console

8 Nm 9 1 Nm hand tight

08000 Lube oil system

Pretightening value Re-tightening value

ID no.

Name

Remark

08001 Oil filter 10 -12 Nm

Oil gasket lightly Screw on by hand and screw tight Torx screw

08003 Oil filter console on crankcase 08010 Lube oil pump on crankcase 08015 Oil suction intake pipe on crankcase 08035 Pipe support oil dipstick guide pipe on oil pump 08042 Oil pressure line on: Turbocharger Crankcase

21 Nm 22 Nm 21 Nm

Note gasket coating Sealant DEUTZ DW 73

30 Nm Renew CU sealing rings Hollow screw Before assembling the line ATL via pressure oil connection bore, pre-oil with approx. 1 cm engine oil! Screwed socket Flange socket FL/M engine BFL/M engines Hollow screw Injection adjustment Renew CU sealing rings Hollow screw

29 Nm

08044 Oil return pipe on turbocharger Oil return pipe on turbocharger 08046 Holder for stopper on crankcase Oil return pipe (ATL) holding plate on crankcase 08047 Oil return pipe (ATL) on crankcase 08048 Oil line to (control line): oil filter console Crankcase

40 Nm 8.5 Nm 8.5 Nm 8.5 Nm 29 Nm

18 Nm

11/2004

10/14

0312 1643 - 0138

4 Technical data 2011

ID no. Name Pretightening value 21 Nm

4.2 Tightening specifications

Re-tightening value

Remark

08051 Oil cooler fastening screws 08053 Locking screw thermostat for injection adjuster on oil filter console 08054 Oil cooler connection on crankcase 08061 Transfer nipple on crankcase (heater connection) 08062 Locking screws M18 x 1.5 mm at transfer nipple (heater connection) 08072 Locking screw oil cooler thermostat on crankcase 08091 Oil pressure switch (locking screw) on crankcase 08093 Oil pressure sensor on crankcase 08094 Locking screw (oil pressure sensor) on crankcase

Torx screw M8

90 Nm

Injection adjustment

13 Nm

M6 x 60mm Hexagon head screw Renew sealing rings Note installation position Renew CU sealing rings

111 11 Nm

50 Nm

50 Nm

Hexagon socket Oil pressure switch M10 x 1mm

13 1.5 Nm 20 +2 Nm

50 Nm

Oil pressure switch / oil pressure sensor M18 x 1.5mm

08095 Oil temperature sensor on crankcase 08096 Locking screw (oil temperature sensor) on crankcase 08098 Locking screw (oil pressure regulating valve) on crankcase 08099 Locking screw on crankcase (without air press lubrication)

25 2.5 Nm Renew CU sealing rings Oil temperature sensor Renew CU sealing rings Oil pressure regulating valve M10 x 1mm M18 x 1.5mm M22 x 1.5mm

28 Nm

111 Nm 18 2 Nm 60 6 Nm 80 8 Nm

11/2004

11/14

0312 1643 - 0138

4 Technical data
4.2 Tightening specifications
09000 Cooling system
Pretightening value 22 Nm 30 Nm 09042 Fan on flange hub, crankshaft 09065 Cooling blower jacket on generator 09066 Blower jacket on cylinder head Cooling blower on: air duct Cylinder head 09067 Blower jacket inlet on generator 09070 Stand plate on: crankcase Oil cooler 09087 Air duct cowling on: Cylinder head Stand plate 09089 Air duct on cooling blower 09098 Air duct on cylinder head 30 Nm 4 Nm 22 Nm Re-tightening value

2011

ID no.

Name

Remark

09041 Fan on fan drive

M8 x 22mm / bolts 8.8 M8 x 20mm / bolts 10.9 M8 x 40mm

21 Nm

22 Nm

21 Nm

Torx screw 8 x 20mm

21 Nm

3 Nm 3 Nm

21 Nm

+21 Nm

12000 Other components

Pretightening value 30 Nm Re-tightening value + 60 + 30

ID no.

Name

Remark

12001 Flywheel on crankcase

Renew screws after every disassembly M10 x 40mm

12030 Flange hub on toothed belt wheel, crankshaft 12031 V-belt pulley on toothed belt wheel, crankshaft 12041 V-belt tensioning roller (holder) on front cover

43 Nm

42 4 Nm

45 Nm

11/2004

12/14

0312 1643 - 0138

4 Technical data 2011

ID no. Name Pretightening value 21 Nm 22 Nm 21 Nm 57 Nm Hexagon bolts

4.2 Tightening specifications

Re-tightening value

Remark

12043 V-belt tensioning roller on holder

M8 x 20mm M8 x 30mm Torx M8 x 16mm

12046 V-belt pulley on fan mounting 12047 V-belt guard on front cover 12051 Hydraulic pump on hydraulic pump console 12052 Toothed belt tensioning roller on hydraulic pump console 12056 Protective hood on hydraulic pump console 12057 Hydraulic pump console on crankcase

8 +2 Nm

+21 2 Nm

Hydraulic pump drive

8.5 Nm

57 Nm

13000 Electrical components

Pretightening value 43,5 Nm 75 7 Nm 8.5 Nm without connection housing Bolts M6 with built up fan drive Unit design Re-tightening value

ID no.

Name

Remark

13001 Starter on crankcase 13006 Starter console on crankcase 13009 Heat shield for starter 13010 Generator console on: crankcase Cylinder head Generator console on crankcase

34 Nm

30 Nm

49

with built up fan drive Unit design with built up fan drive Unit design with built up fan drive Building machine design with built up fan drive Unit design with built up fan drive Building machine design

13012 Generator on console

34 Nm

34 Nm 13015 Generator on clamping bracket

22 Nm

21 Nm

11/2004

13/14

0312 1643 - 0138

4 Technical data
4.2 Tightening specifications
Pretightening value 22 Nm Re-tightening value

2011
Remark

ID no.

Name

13016 Clamping bracket on console Generator

with built up fan drive Unit design with built up fan drive Building machine design

21 Nm 13017 V-belt clamping bracket on front cover 13018 Generator console on cylinder head 13021 Pulley on generator

45 Nm

34 Nm 50 Nm 50 Nm

with in-built fan drive

Running wheel on generator 13022 Fan drive on generator console

30 Nm

120

M10 x 110mm with built up fan drive Unit design

13031 Helical heater plug in: charge air line Suction pipe 13071 Charging current cable on starter 13081 Charging current cable on generator B+ 13082 Cable G1.D+ on generator 13083 Cable G1.W on generator 13092 Cable harness holder on crankcase Cable harness holder on: Starter crankcase

60 Nm

max. 15 Nm 5.5 -7 Nm 4.5 0.8 Nm 4 Nm 14 Nm Torx screw M8 x 16mm

8.5 Nm

M6

11/2004

14/14

0312 1643 - 0138

2011

5
5.1

Job card overview

Sorted alphabetically

11/2004

1/6

0312 1644 - 0138

5 Job card overview

5.1 Sorted alphabetically Notes

2011

11/2004

2/6

0312 1644 - 0138

5 Job card overview 2011

Activity Assemble and disassemble engine on assembly stand Check and repair injection valve Check and set valve clearance Check camshaft Check compression Check con rod Check con rod (crack con rod) Check crankcase Check cylinder Check engine control times Check piston Check piston rings and piston ring grooves Check start of pumping Check valve guide Check valve lag Check valves Check V-belt, renew (in FL and BFL engines) Check V-belt, renew (in FM and BFM engines) Checking and setting injection valves (leak fuel-less) Determine the thickness of the shim gasket Disassemble and complete, check toggle lever and toggle lever block Dismantle and complete cooling blower, check Dismantle and complete fan drive Dismantle and complete front cover (speed governor with torque adaption)

5.1 Sorted alphabetically

Job card W 00-05-01 W 07-07-02 W 01-01-01 W 04-05-06 W 00-02-06 W 02-03-01 W 02-03-01 W 02-01-07 W 03-03-01 W 04-04-11 W 02-09-07 W 02-10-03 W 07-06-04 W 01-06-03 W 01-07-08 W 01-05-04 W 12-02-01 W 12-02-01 W 07-07-05 W 07-06-03 W 01-02-06 W 09-11-02 W 09-13-01 W 03-08-03 Maintenance group Engine general Fuel system Cylinder head Engine control Engine general Drive system Drive system Drive system Crankcase Engine control Drive system Drive system Fuel system Cylinder head Cylinder head Cylinder head Other components Other components Fuel system Fuel system Cylinder head Cooling system Cooling system Crankcase

11/2004

3/6

0312 1644 - 0138

5 Job card overview

5.1 Sorted alphabetically
Activity Dismantle and complete front cover (speed governor without torque adaption) Machine valve seat ring Remove and install air intake pipe Remove and install cable harness Remove and install camshaft Remove and install camshaft bearing, check Remove and install charge pressure-depedent full load stop (LDA) Job card W 03-08-03 I 01-07-07 W 06-07-03 W 13-01-02 W 04-05-05 W 03-11-01 W 07-08-02 W 03-09-04 W 09-11-01 W 02-04-01 W 03-01-11 W 01-04-04 W 06-01-05 W 12-06-01 W 03-08-01 W 07-10-08 W 07-10-06 W 07-10-06 W 07-11-01 W 13-02-03 W 13-02-03 W 07-02-06 W 13-06-01 W 12-08-02

2011
Maintenance group Crankcase Cylinder head Exhaust system / Charging Electrical system Engine control crankcase Fuel system crankcase Cooling system Drive system crankcase Cylinder head Exhaust system / Charging Other components Crankcase Fuel system Fuel system Fuel system Fuel system Electrical system Electrical system Fuel system Electrical system Other components

Remove and install connection housing Remove and install cooling blower Remove and install crankcase Remove and install crankcase bleeding Remove and install cylinder head Remove and install exhaust manifold Remove and install flywheel Remove and install front cover (opposite side to flywheel) Remove and install fuel filter console Remove and install fuel lines (with Bosch injection pumps) Remove and install fuel lines (with leak fuel line) Remove and install fuel pump Remove and install generator (in FL and BFL engines) Remove and install generator and holder (in FM and BFM engines) Remove and install control linkage and guide bushes Remove and install helical heater plugs Remove and install hydraulic pump

11/2004

4/6

0312 1644 - 0138

5 Job card overview 2011

Activity Remove and install injection pumps (Bosch) Remove and install injection pumps (Motorpal) Remove and install injection valves Remove and install lifting magnet (shutoff magnet) Remove and install lifting magnet for start volume release Remove and install lube oil pump Remove and install lube oil tray Remove and install oil cooler Remove and install oil filter cartridge Remove and install oil filter console Remove and install oil intake pipe Remove and install oil pressure sensor Remove and install oil pressure line (turbocharger) Remove and install oil pressure regulating valve, check Remove and install oil pressure switch Remove and install oil line for injection adjuster supply Remove and install oil return line (turbocharger) Remove and install oil temperature sensor Remove and install oil temperature sensor (in engines with injection adjustment) Remove and install oil thermostat (oil cooler) Remove and install piston bolt bush Remove and install piston cooling nozzles Remove and install pistons and con rod Remove and install pistons and con rod (crack con rod) Remove and install rear cover (flywheel side)

5.1 Sorted alphabetically

Job card W 07-04-01 W 07-04-01 W 07-07-01 W 11-00-03 W 07-02-07 W 08-04-05 W 08-04-07 W 08-08-02 W 08-10-06 W 08-11-07 W 08-04-06 W 08-11-09 W 08-15-01 W 08-11-02 W 08-11-08 W 08-16-01 W 08-15-02 W 08-11-11 W 08-16-02 W 08-11-12 W 02-03-03 W 02-15-01 W 02-09-03 W 02-09-03 W 03-09-01 Maintenance group Fuel system Fuel system Fuel system Monitoring system Fuel system Lube oil system Lube oil system Lube oil system Lube oil system Lube oil system Lube oil system Lube oil system Lube oil system Lube oil system Lube oil system Lube oil system Lube oil system Lube oil system Lube oil system Lube oil system Drive system Drive system Drive system Drive system Crankcase

11/2004

5/6

0312 1644 - 0138

5 Job card overview

5.1 Sorted alphabetically
Activity Remove and install solenoid valve (LDA) Remove and install speed governor Remove and install starter Remove and install toggle lever and toggle lever block Remove and install toothed belt and clamping roller of the hydraulic pump Remove and install turbocharger Remove and install V-belt clamping roller Job card W 07-08-01 W 05-07-01 W 13-03-02 W 01-02-02 W 12-08-03 W 06-06-04 W 12-02-06 W 01-05-01 W 04-03-01 W 02-02-04 W 02-02-02 W 07-03-01 W 04-04-12

2011
Maintenance group Fuel system Speed governing Electrical system Cylinder head Other components Exhaust system / Charging Other components Cylinder head Engine control Drive system Drive system Fuel system Engine control

Remove and install valves Renew camshaft sealing ring (opposite side to flywheel) Renew crankshaft sealing ring (opposite side to flywheel) Renew crankshaft sealing ring (flywheel side) Renew injection lines Renew toothed belt and clamping roller (new version of clamping roller) Renew toothed belt and clamping roller (old version of clamping roller) Renew toothed starter flywheel ring

W 04-04-12 W 12-06-03

Engine control Other components

11/2004

6/6

0312 1644 - 0138

2011

5
5.2

Job card overview

Sorted numerically

11/2004

1/6

0312 1645 - 0138

5 Job card overview

5.2 Sorted numerically Notes

2011

11/2004

2/6

0312 1645 - 0138

5 Job card overview 2011

Job card W 00-02-06 W 00-05-01 W 01-01-01 W 01-02-02 W 01-02-06 W 01-04-04 W 01-05-01 W 01-05-04 W 01-06-03 I 01-07-07 W 01-07-08 W 02-01-07 W 02-02-02 W 02-02-04 W 02-03-01 W 02-03-01 W 02-03-03 W 02-04-01 W 02-09-03 W 02-09-03 W 02-09-07 W 02-10-03 W 02-15-01 W 03-01-11 W 03-03-01 Check compression Assemble and disassemble engine on engine block Check and set valve clearance Remove and install toggle lever and toggle lever block Disassemble and complete, check toggle lever and toggle lever block Remove and install cylinder head Remove and install valves Check valves Check valve guide Machine valve seat ring Check valve lag Check crankcase Renew crankshaft sealing ring (flywheel side) Renew crankshaft sealing ring (opposite side to flywheel) Check con rod Check con rod (crack con rod) Remove and install piston bolt bush Remove and install crankcase Remove and install pistons and con rod Remove and install pistons and con rod (crack con rod) Check piston Check piston rings and piston ring grooves Remove and install piston cooling nozzles Remove and install crankcase bleeding Check cylinder Activity

5.2 Sorted numerically

Maintenance group Engine general Engine general Cylinder head Cylinder head Cylinder head Cylinder head Cylinder head Cylinder head Cylinder head Cylinder head Cylinder head Drive system Drive system Drive system Drive system Drive system Drive system Drive system Drive system Drive system Drive system Drive system Drive system Crankcase Crankcase

11/2004

3/6

0312 1645 - 0138

5 Job card overview

5.2 Sorted numerically
Job card W 03-08-01 W 03-08-03 Activity Remove and install front cover (opposite side to flywheel) Dismantle and complete front cover (speed governor with torque adaption) Dismantle and complete front cover (speed governor without torque adaption) Remove and install rear cover (flywheel side) Remove and install connection housing Remove and install camshaft bearing, check Renew camshaft sealing ring (opposite side to flywheel) Check engine control times Renew toothed belt and clamping roller (old version of clamping roller) Renew toothed belt and clamping roller (new version of clamping roller) Remove and install camshaft Check camshaft Remove and install speed governor Remove and install exhaust manifold Remove and install turbocharger Remove and install air intake pipe Remove and install control linkage and guide bushes Remove and install lifting magnet for start volume release Renew injection lines Remove and install injection pumps (Bosch) Remove and install injection pumps (Motorpal) Determine the thickness of the shim gasket Check start of pumping

2011
Maintenance group Crankcase Crankcase

W 03-08-03 W 03-09-01 W 03-09-04 W 03-11-01 W 04-03-01

Crankcase Crankcase Crankcase Crankcase Engine control Engine control Engine control

W 04-04-11 W 04-04-12

W 04-04-12 W 04-05-05 W 04-05-06 W 05-07-01 W 06-01-05 W 06-06-04 W 06-07-03 W 07-02-06 W 07-02-07 W 07-03-01 W 07-04-01 W 07-04-01 W 07-06-03 W 07-06-04

Engine control Engine control Engine control Speed governing Exhaust system / Charging Exhaust system / Charging Exhaust system / Charging Fuel system Fuel system Fuel system Fuel system Fuel system Fuel system Fuel system

11/2004

4/6

0312 1645 - 0138

5 Job card overview 2011

Job card W 07-07-01 W 07-07-02 W 07-07-05 W 07-08-01 W 07-08-02 W 07-10-06 W 07-10-06 W 07-10-08 W 07-11-01 W 08-04-05 W 08-04-06 W 08-04-07 W 08-08-02 W 08-10-06 W 08-11-02 W 08-11-07 W 08-11-08 W 08-11-09 W 08-11-11 W 08-11-12 W 08-15-01 W 08-15-02 W 08-16-01 W 08-16-02 Activity Remove and install injection valves Check and repair injection valve Checking and setting injection valves (leak fuel-less) Remove and install solenoid valve (LDA) Remove and install charge pressure-depedent full load stop (LDA) Remove and install fuel lines (with Bosch injection pumps) Remove and install fuel lines (with leak fuel line) Remove and install fuel filter console Remove and install fuel pump Remove and install lube oil pump Remove and install oil intake pipe Remove and install lube oil tray Remove and install oil cooler Remove and install oil filter cartridge Remove and install oil pressure regulating valve, check Remove and install oil filter console Remove and install oil pressure switch Remove and install oil pressure sensor Remove and install oil temperature sensor Remove and install oil thermostat (oil cooler) Remove and install oil pressure line (turbocharger) Remove and install oil return line (turbocharger) Remove and install oil line for injection adjuster supply Remove and install oil temperature sensor (in engines with injection adjustment)

5.2 Sorted numerically

Maintenance group Fuel system Fuel system Fuel system Fuel system Fuel system Fuel system Fuel system Fuel system Fuel system Lube oil system Lube oil system Lube oil system Lube oil system Lube oil system Lube oil system Lube oil system Lube oil system Lube oil system Lube oil system Lube oil system Lube oil system Lube oil system Lube oil system Lube oil system

11/2004

5/6

0312 1645 - 0138

5 Job card overview

5.2 Sorted numerically
Job card W 09-11-01 W 09-11-02 W 09-13-01 W 11-00-03 W 12-02-01 W 12-02-01 W 12-02-06 W 12-06-01 Activity Remove and install cooling blower Dismantle and complete cooling blower, check Dismantle and complete fan drive Remove and install lifting magnet (shutoff magnet) Check V-belt, renew (in FL and BFL engines) Check V-belt, renew (in FM and BFM engines) Remove and install V-belt clamping roller Remove and install flywheel Renew toothed starter flywheel ring Remove and install hydraulic pump Remove and install toothed belt and clamping roller of the hydraulic pump Remove and install cable harness Remove and install generator (in FL and BFL engines) Remove and install generator and holder (in FM and BFM engines) Remove and install starter Remove and install helical heater plugs

2011
Maintenance group Cooling system Cooling system Cooling system Monitoring system Other components Other components Other components Other components Other components Other components Other components Electrical system Electrical system Electrical system Electrical system Electrical system

W 12-06-03 W 12-08-02 W 12-08-03 W 13-01-02 W 13-02-03 W 13-02-03 W 13-03-02 W 13-06-01

11/2004

6/6

0312 1645 - 0138

2011

5
5.3

Job card overview

Job card references

11/2004

1/10

0312 1646 - 0138

5 Job card overview

5.3 Job card references
Explanation of job card reference: Owing to the job card structure, individual parts of the work processes may overlap or repeat. Illustrations of the same working environment may also deviate slightly.

2011

11/2004

2/10

0312 1646 - 0138

5 Job card overview 2011

00 Engine general
Job card Activity Other job cards necessary for performing the activity W 01-01-01 W 07-07-01 W 08-08-02

5.3 Job card references

W 00-02-06 Check compression Assemble and W 00-05-01 disassemble engine on engine block

W 13-03-02

01

Cylinder head
Job card Activity Check and set valve clearance Other job cards necessary for performing the activity

W 01-01-01

Remove and install toggle W 01-02-02 lever and toggle lever W 01-01-01 block Disassemble and complete, check toggle W 01-02-06 lever and toggle lever block W 01-04-04 Remove and install cylinder head

W 01-02-02

W 01-02-02 W 06-07-03 W 07-07-01 W 09-11-01 W 13-02-03

W 01-05-01 Remove and install valves W 01-04-04 W 01-05-04 Check valves W 01-06-03 Check valve guide I 01-07-07 Machine valve seat ring W 01-05-01 W 01-05-01 W 01-05-01 W 01-07-08 W 01-04-04

W 01-07-08 Check valve lag

0312 1646 - 0138

3/10

0312 1646 - 0138

5 Job card overview

5.3 Job card references
02 Drive system
Job card Activity Other job cards necessary for performing the activity W 02-04-01

2011

W 02-01-07 Check crankcase W 02-02-02

Renew crankshaft sealing W 12-06-01 ring (flywheel side)

Renew crankshaft sealing W 04-04-12 W 04-04-12 W 02-02-04 ring (opposite side to W 03-08-01 (old version) (new version) flywheel) W 02-03-01 Check con rod W 02-03-01 Check con rod (crack con rod) W 02-03-03 W 02-03-03

5
W 02-03-03 W 02-04-01

Remove and install piston W 02-09-03 bolt bush Remove and install crankcase W 02-01-07 W 02-09-03 W 03-08-01 W 03-09-01

W 02-09-03

Remove and install pistons W 01-04-04 W 02-10-03 W 08-04-06 and con rod

Remove and install pistons W 02-09-03 and con rod (crack con W 01-04-04 W 02-10-03 W 08-04-06 rod) W 02-09-07 Check piston W 02-10-03 Check piston rings and piston ring grooves W 02-09-03 W 02-09-03

W 02-15-01

Remove and install piston W 02-04-01 cooling nozzles

11/2004

4/10

0312 1646 - 0138

5 Job card overview 2011

03 Crankcase
Job card W 03-01-11 Activity Remove and install crankcase bleeding W 01-04-04 W 04-04-12 W 04-04-12 (new W 08-04-05 W 08-08-02 (old version) version) Other job cards necessary for performing the activity

5.3 Job card references

W 03-03-01 Check cylinder Remove and install front W 03-08-01 cover (opposite side to flywheel) Dismantle and complete front cover (speed W 03-08-03 governor with torque adaption) Dismantle and complete front cover (speed W 03-08-03 governor without torque adaption) W 03-09-01 Remove and install rear cover (flywheel side) Remove and install connection housing Remove and install camshaft bearing, check

W 04-03-01

W 03-08-01

5
W 03-08-01

W 03-09-04 W 08-04-07

W 03-09-04

W 00-05-01 W 12-06-01 W 07-04-01 W 07-04-01 W 07-11-01 (Motorpal) (Bosch)

W 03-11-01

W 01-02-02 W 02-04-01

0312 1646 - 0138

5/10

0312 1646 - 0138

5 Job card overview

5.3 Job card references
04 Engine control
Job card Activity Other job cards necessary for performing the activity W 04-04-12 (old version) W 04-04-12 (new version) W 04-04-12 (new version)

2011

Renew camshaft sealing W 04-03-01 ring (opposite side to flywheel) Check engine control times

W 04-04-11

W 04-04-12 (old version)

Renew toothed belt and W 12-02-01 W 12-02-01 W 04-04-12 clamping roller (old version (FL, BFL (FM, BFM W 12-08-03 of clamping roller) engines) engines) Renew toothed belt and W 12-02-01 W 12-02-01 W 04-04-12 clamping roller (new (FL, BFL (FM, BFM W 12-08-03 version of clamping roller) engines) engines) W 04-04-12 (old version) W 04-04-12 W 07-04-01 (new (Motorpal) version)

W 01-02-02 W 03-09-01 W 04-05-05 Remove and install camshaft W 07-04-01 W 07-11-01 (Bosch) W 04-05-06 Check camshaft W 04-05-05

05

Speed governing

W 05-07-01

Remove and install speed governor

06

Exhaust system / Charging

W 06-01-05

Remove and install exhaust manifold Remove and install turbocharger Remove and install air intake pipe

W 06-06-04

W 06-06-04

W 06-07-03

W 06-01-05

11/2004

6/10

0312 1646 - 0138

5 Job card overview 2011

07 Fuel system
Job card Activity Other job cards necessary for performing the activity W 03-08-01 W 03-09-04 W 07-04-01 W 07-04-01 W 07-08-02 (Motorpal) (Bosch)

5.3 Job card references

Remove and install control W 07-02-06 linkage and guide bushes

W 08-11-12 W 09-11-01 W 13-02-03 Remove and install lifting W 07-02-07 magnet for start volume release W 07-03-01 Renew injection lines W 07-04-01 Remove and install injection pumps (Bosch) W 08-08-02 W 07-03-01 W 07-06-04 W 07-10-06

W 07-04-01

Remove and install W 07-03-01 W 07-06-03 W 07-06-04 W 07-10-06 injection pumps (Motorpal) Determine the thickness of W 07-04-01 the shim gasket W 07-03-01 W 07-10-06 W 07-10-06 W 11-00-03 (Bosch) (Motorpal)

W 07-06-03

W 07-06-04 Check start of pumping Remove and install injection valves

W 07-07-01

W 07-03-01

W 07-07-02

Check and repair injection W 07-07-05 W 07-07-01 valve

Checking and setting W 07-07-05 injection valves (leak fuel- W 07-07-01 less) W 07-08-01 Remove and install solenoid valve (LDA)

Remove and install charge W 07-08-02 pressure-depedent full load stop (LDA) Remove and install fuel W 07-10-06 lines (with Bosch injection W 08-08-02 pumps) W 07-10-06 Remove and install fuel lines (with leak fuel line) Remove and install fuel filter console

W 07-10-08

0312 1646 - 0138

7/10

0312 1646 - 0138

5 Job card overview

5.3 Job card references
Job card W 07-11-01 Activity Remove and install fuel pump

2011
Other job cards necessary for performing the activity

08

Lube oil system

Job card Activity Other job cards necessary for performing the activity W 04-04-12 (new version)

W 08-04-05

Remove and install lube oil W 04-04-12 pump (old version) Remove and install oil intake pipe Remove and install lube oil tray Remove and install oil cooler Remove and install oil filter cartridge

W 08-04-06

W 08-04-07

5
W 08-04-07 W 08-08-02

W 08-10-06

Remove and install oil W 08-11-02 pressure regulating valve, check W 08-11-07 Remove and install oil filter W 08-10-06 console Remove and install oil pressure switch Remove and install oil pressure sensor Remove and install oil temperature sensor Remove and install oil thermostat (oil cooler) W 08-08-02

W 08-11-08

W 08-11-09

W 08-11-11

W 08-11-12

Remove and install oil W 08-15-01 pressure line (turbocharger) W 08-15-02 Remove and install oil return line (turbocharger)

11/2004

8/10

0312 1646 - 0138

5 Job card overview 2011

Job card Activity

5.3 Job card references

Other job cards necessary for performing the activity

Remove and install oil line W 08-16-01 for injection adjuster supply Remove and install oil temperature sensor (in W 08-16-02 engines with injection adjustment)

09

Cooling system
Job card Activity Remove and install cooling blower Dismantle and complete cooling blower, check Dismantle and complete fan drive Other job cards necessary for performing the activity W 12-02-01 (FL, BFL engines) W 09-11-01

W 09-11-01

W 09-11-02

W 09-13-01

11

Monitoring system
Job card Activity Remove and install lifting magnet (shutoff magnet) Other job cards necessary for performing the activity W 13-02-03 (FM, BFM engines)

W 11-00-03

W 12-02-06

12

Other components
Job card Activity Check V-belt, renew (in FL and BFL engines) Check V-belt, renew (in FM and BFM engines) Remove and install V-belt clamping roller W 12-02-01 W 12-02-01 (FL, BFL (FM, BFM engines) engines) Other job cards necessary for performing the activity

W 12-02-01

W 12-02-01

W 12-02-06

0312 1646 - 0138

9/10

0312 1646 - 0138

5 Job card overview

5.3 Job card references
Job card W 12-06-01 Activity Remove and install flywheel Renew toothed starter flywheel ring Remove and install hydraulic pump W 12-06-01

2011
Other job cards necessary for performing the activity

W 12-06-03

W 12-08-02

Remove and install W 12-02-01 W 12-02-01 toothed belt and clamping W 12-08-03 (FL, BFL (FM, BFM roller of the hydraulic engines) engines) pump

13

Electrical components
Job card Activity Remove and install cable harness Other job cards necessary for performing the activity

W 13-01-02

Remove and install W 13-02-03 generator (in FL and BFL engines) Remove and install W 13-02-03 generator and holder (in FM and BFM engines) W 13-03-02 Remove and install starter W 13-06-01 Remove and install helical heater plugs

W 12-02-01

W 12-02-01

11/2004

10/10

0312 1646 - 0138

2011

Job cards
6

11/2004

1/2

0312 1647 - 0138

6 Job cards 2011

Notes

11/2004

2/2

0312 1647 - 0138

2011
W 00-02-06

Engine general W 00-02-06

Check compression
Tools
- Commercial tools 8005 - Compression tester 8189 - Torx tool kit - Special tools 100 120 - Connecting piece

References
- W 01-01-01 - W 07-07-01 - W 08-08-02

Check compression Check and set valve clearance Job card W 01-01-01. Remove injection valves Job card W 07-07-01. In FL, BFL engines Install oil cooler Job card W 08-08-02.

39104 0

Insert adapter (1) with sealing ring.

Note
Use sealing ring from injection valve.

39105 0
11/2004

1/4

0312 1553 - 0138

Engine general W 00-02-06

Fit clamping claw (1) and tighten screws (2) .

2011

Note
Note installation position.

07001

39106 0

If necessary, mount adapter (1) on connection piece.

39107 0

Connect compression tester to connection piece or adapter. Turn over engine with starter.
00 51

39102 0
11/2004

2/4

0312 1553 - 0138

2011
The measured compression pressure depends on the starting speed during the measuring process and the altitude of the engine installation site. Limit values can therefore not be determined exactly. The compression measurement is only recommended as a reference measurement of all cylinders of an engine to each other. If more than 15% deviation has been determined, the cause should be determined by disassembling the cylinder unit concerned.

Engine general W 00-02-06

No.
Kompression in bar Compression value in bar Pression en bar Dat. _________ 30 35 40 10 15 20 25

Zyl. 1 2 3 4 5 6 7 8

Best. Nr. 5 1341 250 00

DBGM

Made in Germany

MOTOMETER 7250 Leonberg

33771 1

Remove the compression tester and adapter.

39102 0

Unscrew screw (1). Remove connection piece with sealing ring. In FL, BFL engines Remove oil cooler Job card W 08-08-02. Install injection valves Job card W 07-07-01.

39103 0
11/2004

3/4

0312 1553 - 0138

Engine general W 00-02-06

Notes

2011

11/2004

4/4

0312 1553 - 0138

2011
W 00-05-01

Engine general W 00-05-01

Mount engine on assembly stand and disassemble

Tools
- Commercial tools - Special tools 6067 - Engine assembly block 6067/115 - Clamping holder 6067/114 - Support arm

References
- W 13-03-02

Note
In the repair procedure shown here different customer scopes are not taken into consideration, i.e. add-on parts deviating from standard are not shown.

Auxiliary material
- Lifting gear - Support ropes - Eyebolts

Assemble engine on engine block Remove starter Job card W 13-03-02. Screw in eyebolt (1). Hang engine on suitable workshop crane.

6
1 1

39500 0

Unscrew screws (1) and remove engine bearing (2) of the Manifold side.
00 81

39501 0
11/2004

1/6

0312 1554 - 0138

Engine general W 00-05-01

In FL, FM engines Unscrew screw (1) and remove holder. Pull out stopper (2).

2011

2 1

39502 0

In BFL, BFM engines Unscrew screw (1) and remove holder. Remove oil return pipe (arrow).

34015 1

Mount clamping holder (1) on the Manifold side and tighten screws (2).
00001

39503 0
11/2004

2/6

0312 1554 - 0138

2011
Mount clamping holder on engine assembly block. Fit counter plate (1). Insert screws and nuts (2).
00002

Engine general W 00-05-01

Unhook engine from workshop crane and unscrew eyebolt.

39504 0

Remove engine from assembly block. Screw in eyebolt. Hang engine on suitable workshop crane. Unscrew nuts (2), remove counter plate (1) and bolts.

39504 0

Unscrew screws (2) and remove clamping holder (1).

39503 0
11/2004

3/6

0312 1554 - 0138

Engine general W 00-05-01

In FL, FM engines Pull new round sealing ring (arrow) onto stopper.

2011

39505 0

Insert stopper (2).

Note
Oil round sealing ring lightly

Mount holder and tighten screw (1).

08046

2 1

39502 0

In BFL, BFM engines Pull new round sealing rings onto screwed socket (arrow) and oil return pipe.

34266 1
11/2004

4/6

0312 1554 - 0138

2011
Insert oil return pipe (arrow). Mount holder and tighten screw (1).
08044

Engine general W 00-05-01

34015 1

Mount engine bearing (2) and tighten screws (1).

00003

Unhook engine from workshop crane and unscrew eyebolt. Install starter Job card W 13-03-02

39501 0

11/2004

5/6

0312 1554 - 0138

Engine general W 00-05-01

Notes

2011

11/2004

6/6

0312 1554 - 0138

2011
W 01-01-01

Cylinder head W 01-01-01

Check and set valve clearance

Tools
- Commercial tools Feeler gauges

Note
The standard valve clearance setting is possible: - On cold or warm engine after a cooling time of at least 0.5 h. - Oil temperature < 80 C.

Removal Unscrew screws (arrows), remove starter cylinder head cover (1) and gasket.

39131 0

Set engine to valve overlap Turn crankshaft until reaching valve overlap on cylinder no. 1.
01 63

39132 0
11/2004

1/4

0312 1555 - 0138

Cylinder head W 01-01-01

Note
Valve overlap means: - Outlet valve not yet closed. - The inlet valve starts opening.

2011

39133 0

Check valve clearance Arrangement of inlet and outlet valves. - IN = inlet valve - EX = outlet valve

EX

IN

EX

IN

EX

IN

EX

IN

39134 0

Check valve clearance setting with feeler gauge blade on the appropriate cylinder.
01 63 01 61 01 62

Note
The feeler gauge blade must go between the toggle lever sliding surface and the valve with little resistance.

39135 0
11/2004

2/4

0312 1555 - 0138

2011
Setting valve clearance Loosen lock nut (1). Correct valve clearance by turning the setting screw (2).

Cylinder head W 01-01-01

Note
- If valve clearance is too small, unscrew the setting screw. - If valve clearance is too great, screw in the setting screw.
01 61 01 62

39136 0

Tighten lock nut (1).

Note
Do not turn the setting screw (2) when tightening the lock nut.
01003

Check the valve clearance again with a feeler gauge blade.

1
39137 0

Assembly Clean the sealing surface on the cylinder head cover and cylinder head. Fit gasket.

Note
Note installation position, the gate (arrow) must face the front cover.

39138 0
11/2004

3/4

0312 1555 - 0138

Cylinder head W 01-01-01

Mount cylinder head cover and tighten screws alternately.
01004

2011

39139 0

11/2004

4/4

0312 1555 - 0138

2011
W 01-02-02

Cylinder head W 01-02-02

Remove and install toggle lever and toggle lever block

Tools
- Commercial tools

References
- W 01-01-01

Remove toggle lever and toggle lever block Unscrew screws (arrows). Remove cylinder head cover (1) and gasket.

39131 0

Unscrew screws (1) and remove toggle lever with toggle lever block (2).

Note
- Loosen screws evenly to avoid jamming the toggle lever blocks. - Set down the components in the order of installation.

2
39140 0
11/2004

1/4

0312 1556 - 0138

Cylinder head W 01-02-02

Remove stop rods (1).

2011

Note
Set down the components in the order of installation.

Check stop rods for visible signs of damage.

1 1

39141 0

Insert stop rods (1).

Note
- Note the assignment of the stop rods. - The stop rod must be seated in the socket of the ram with the ball head.

1 1

39141 0

Install toggle lever and toggle lever block Loosen the lock nuts of the setting screws and turn back the setting screws. Mount toggle lever block (1).

Note
The ball heads must be seated in the sockets of the stop rods (arrows).

39142 0
11/2004

2/4

0312 1556 - 0138

2011
Tighten (1) screws alternately.

Cylinder head W 01-02-02

Note
- Make sure that the stop rods are not under stress due to valve overlap when tightening the bolts. - Align toggle lever to the stop rods/valves.
01002

Check and set valve clearance Job card W 01-01-01.

39143 0

Clean the sealing surface on the cylinder head cover and cylinder head. Fit gasket.

Note
Note installation position, the gate (arrow) must face the front cover.

39138 0

Mount cylinder head cover and tighten screws alternately.

01004

39139 0
11/2004

3/4

0312 1556 - 0138

Cylinder head W 01-02-02

Notes

2011

11/2004

4/4

0312 1556 - 0138

2011
W 01-02-06

Cylinder head W 01-02-06

Disassemble and complete, check toggle lever and toggle lever block
Tools
- Commercial tools Internal measuring device Micrometer gauge

References
- W 01-02-02

Dismantle toggle lever block Remove toggle lever and toggle lever block Job card W 01-02-02. Remove locking rings (1).

6
1

39144 0

Remove toggle lever.

39145 0
11/2004

1/4

0312 1557 - 0138

Cylinder head W 01-02-06

Check toggle lever Measure toggle lever bore with internal measuring device.
01 72 01 73

2011

Note
If the wear limit is reached, change the toggle lever.

39032 0

Unscrew lock nut (1) and turn out setting screw (1).

39146 0

Check components for visible signs of wear. Check oil channels (arrows) for free passage.

39147 0
11/2004

2/4

0312 1557 - 0138

2011
Turn setting screw (2) into the toggle lever and tighten the lock nut (1).

Cylinder head W 01-02-06

39146 0

Check the toggle lever axis Measure toggle lever diameter with micrometer gauge.
01 74

Note
If the wear limit is reached, the toggle lever block has to be changed.

39148 0

Complete the toggle lever block Push toggle lever (1) onto the toggle lever axle (2).

Note
- Oil the toggle lever axle (2) lightly. - The toggle lever sliding surface (3) must face the side with the notch (arrow).

39149 0
11/2004

3/4

0312 1557 - 0138

Cylinder head W 01-02-06

Install locking rings (1).

2011

Note
Pay attention to correct fit of the locking ring in the groove. Install toggle lever and toggle lever block Job card W 01-02-02.

1
39150 0

11/2004

4/4

0312 1557 - 0138

2011
W 01-04-04

Cylinder head W 01-04-04

Remove and install cylinder head

Tools
- Commercial tools 8189 - Torx tool kit - Special tools 100 400 - Meter 100 750 - Measuring device

References
- W 01-02-02 - W 06-07-03 - W 07-07-01 - W 09-11-01 - W 13-02-03

Remove cylinder head Remove air intake pipe Job card W 06-07-03. Remove injection valve Job card W 07-07-01. Remove toggle lever and toggle lever block Job card W 01-02-02. In FM, BFM engines Remove generator Job card W 13-02-03.

39445 0

In FL, BFL engines Remove cooling blower Job card W 09-11-01.

Note
Put down the components in the order of installation, note order of cylinders.

39151 0
11/2004

1/8

0312 1558 - 0138

Cylinder head W 01-04-04

Unscrew screws (arrows), remove cylinder head (1) and gasket. Clean sealing surfaces on cylinder head and crankcase.

2011

39155 0

Determine cylinder head gasket

Note
- The piston overlap must be measured on all pistons to determine the cylinder head gasket. - The cylinder head gasket must be selected according to the greatest measured piston overlap.

39208 0

Determine piston UT Turn crankshaft until the piston closes flush with the crankcase.

Note
Turn crankshaft in direction of rotation of engine.

39156 0
11/2004

2/8

0312 1558 - 0138

2011
Mount shim (1) and measuring bridge (2) on crankcase. Insert meter in measuring bridge and position the stylus with pre-tension on the piston base (arrow). Turn the crankshaft on evenly until the reversal point of the pointer on the meter is reached. The piston is now in UT.

Cylinder head W 01-04-04

39157 0

Determine piston overlap Move measuring bridge and shim. Place the stylus of the meter under pre-tension on the sealing surface of the crankcase (arrow). Adjust meter to "0".

39158 0

Read measuring points.

Note
Schematic representation for measuring the piston overlap at the points "1" and "2".

2
34151 1
11/2004

3/8

0312 1558 - 0138

Cylinder head W 01-04-04

Move the measuring bridge on the shims so that the stylus is applied to the specified measuring points.

2011

Note
- Measuring points, see schematic diagram. - The stylus may not be positioned on the labeling of the piston. Note the greatest measured value.

39159 0

Select the cylinder head gasket according to the greatest measured piston overlap.
02 75 02 76 02 77

Example: Piston overlap = 0.73 mm, corresponds to cylinder head gasket with 2 notches (arrow).

39160 0

Install cylinder head Make sure the clamping pins (arrows) are in place.

39161 0
11/2004

4/8

0312 1558 - 0138

2011
Mount new cylinder head gasket.

Cylinder head W 01-04-04

Note
- Sealing surfaces for the cylinder head gasket must be clean and free of oil. - Identification OBEN / TOP must face up.

39162 0

Mount cylinder head, oil cylinder head bolts lightly and tighten.

Note
Cylinder head bolts can be used a maximum 5 times in case of provability.
01 98

39163 0

Tightening order 2-cylinder Tighten all bolts in the right order.

01001

39152 0
11/2004

5/8

0312 1558 - 0138

Cylinder head W 01-04-04

Tightening order 3-cylinder Tighten all bolts in the right order.
01001

2011

39153 0

Tightening order 4-cylinder Tighten all bolts in the right order.

01001

10

39154 0

In FM, BFM engines Install generator Job card W 13-02-03.

39445 0
11/2004

6/8

0312 1558 - 0138

2011
In FL, BFL engines Install cooling blower Job card W 09-11-01. Install toggle lever and toggle lever block Job card W 01-02-02. Install injection valve Job card W 07-07-01. Install air intake pipe Job card W 06-07-03.

Cylinder head W 01-04-04

39234 0

11/2004

7/8

0312 1558 - 0138

Cylinder head W 01-04-04

Notes

2011

11/2004

8/8

0312 1558 - 0138

2011
W 01-05-01

Cylinder head W 01-05-01

Remove and install valves

Tools
- Commercial tools Caliper gauge 8024 - Assembly pliers 9017 - Assembly lever - Special tools 120 900 - Clamping block 120 910 - Clamping plate 121 410 - Assembly tool

References
- W 01-04-04

Remove valves Remove cylinder head Job card W 01-04-04. Install clamping block (1) on clamping plate (2). Install cylinder head on clamping block.

6
1

2
39164 0

Install valve assembly lever (1). Press down the valve spring with the valve assembly lever and remove both clamping cones (2). Remove valve spring plates, valve springs and valves. Remove valve assembly lever.

39165 0
11/2004

1/4

0312 1559 - 0138

Cylinder head W 01-05-01

Remove valve shaft seal with valve sealing ring pliers.

2011

39166 0

Clean cylinder head, check and inspect for damage. Check components for visible signs of damage.

39167 0

Install valves Measure valve spring length with caliper gauge.

Note
If the wear limit is reached, the valve spring has to be changed.
01 51

35856 1
11/2004

2/4

0312 1559 - 0138

2011
Insert valve, hold tight and push the protective sleeve (1) onto the valve shaft.

Cylinder head W 01-05-01

Note
- Oil the valve shaft slightly. - Cover the valve V-grooves with the protective sleeve (1) or adhesive foil before installing the valve shaft seal every time.

33889 1

Push the new valve shaft seal over the protective sleeve (arrow).

33890 1

Remove the protective sleeve. Press the valve shaft seal in with the assembly tool (1) until it touches.

39168 0
11/2004

3/4

0312 1559 - 0138

Cylinder head W 01-05-01

Insert valve spring (1) and valve spring head (2).

2011
2

39169 0

Install valve assembly lever. Press down the valve spring with the valve assembly lever and insert both clamping cones (1).

Note
Pay attention to correct fit of the clamping cones in the valve V-groove.

39170 0

Remove valve assembly lever Remove cylinder head from clamping block. Install cylinder head Job card W 01-04-04.

39171 0
11/2004

4/4

0312 1559 - 0138

2011
W 01-05-04

Cylinder head W 01-05-04

Check valves
Tools
- Commercial tools Micrometer gauge Caliper gauge

References
- W 01-05-01

Note
- Clean all valves. - If the wear limit is reached, the valve has to be changed.

Valve shaft diameter Remove valves Job card W 01-05-01. Measure valve shaft diameter with micrometer screw.
01 31 01 32

42182 0

Valve edge strength Measure valve edge thickness with caliper gauge.
01 35 01 36

42183 0
11/2004

1/2

0312 1560 - 0138

Cylinder head W 01-05-04

Valve plate diameter Measure head diameter with caliper gauge.
01 37 01 38

2011

Install valves Job card W 01-05-01.

42184 0

11/2004

2/2

0312 1560 - 0138

2011
W 01-06-03

Cylinder head W 01-06-03

Check valve guide

Tools
- Commercial tools Magnetic measuring stand - Special tools 100 400 - Meter

References
- W 01-05-01

Note
- New valves are used for testing. - If the wear limit is reached, the valve guide has to be changed.

Check valve guide Remove valves Job card W 01-05-01. Check valve guide for visible signs of wear. Attach magnetic measuring stand and insert meter. Insert new valve. Apply stylus to the valve head with pre-tension (arrow) and set meter to 0.

33881 1

Measure valve shaft clearance Move valve to and fro in direction of arrow.

Note
- The end of the valve shaft must be flush with the valve guide to measure the valve shaft clearance. - The whole tilt angle must be taken into consideration.
01 33 01 34

39172 0
11/2004

1/2

0312 1561 - 0138

Cylinder head W 01-06-03

Remove magnetic measuring stand and meter. Install valves Job card W 01-05-01.

2011

39173 0

11/2004

2/2

0312 1561 - 0138

2011
I 01-07-07

Cylinder head I 01-07-07

Machine valve seat ring

Tools
- Commercial tools Caliper gauge Valve seat rotating device

References
- W 01-05-01 - W 01-07-08

Note
- The valve seat ring must be reworked in the installed state in the cylinder head. - For handling the valve seat rotating device, observe the respective manufacturers operating manual.

Check valve seat ring Check valve lag Job card W 01-07-08. Remove valves and valve shaft seals Job card W 01-05-01.

39175 0

Check valve seat rings for tight fit and damage.

Note
If the wear limit of valve seat and valve lag is not yet reached and there are no burnthroughs, blow-throughs, tears or marks, it is possible to rework the valve seat ring for further use.

39167 0
11/2004

1/4

0312 1562 - 0138

Cylinder head I 01-07-07

Machine valve seat ring Install valve seat rotating device

2011

Note
Observe different valve seat angles.

01 47

01 48

39353 0

Turn out the valve seat carefully until it is level all round.

Note
- Do not remove more material than necessary from the valve seat. - Check the valve seat after every step.

39353 0

Measure valve seat width with caliper gauge.

01 41 01 42

39379 0
11/2004

2/4

0312 1562 - 0138

2011
Note
The valve set is a little wider after reworking. If necessary, the valve seat width can be reduced by reworking the outer correction angle (1) and also the inner correction angle (2) if necessary.
01 41 01 42

Cylinder head I 01-07-07

Remove valve seat rotating device Remove chips.

2
39393 0

Check contact pattern Coat the sitting surface of the valve cone thinly with varnish. Insert valve and turn 45 to 90. Remove the valve and check the contact pattern.

Note
A continuous surrounding contact between the valve cone and the valve seat ring must be guaranteed at the greatest valve seat diameter (outer contact) with a radial contact percentage of 60 to 100%.

39461 0

Clean valve and valve seat ring. Check valve lag Job card W 01-07-08.

Note
Do not rework valve seat with lapping compound.

39052 0
11/2004

3/4

0312 1562 - 0138

Cylinder head I 01-07-07

Notes

2011

11/2004

4/4

0312 1562 - 0138

2011
W 01-07-08

Cylinder head W 01-07-08

Check valve lag

Tools
- Commercial tools Depth-measuring appliance - Special tools 120 900 - Clamping block 120 910 - Clamping plate

References
- W 01-04-04

Note
If the wear limit is reached, the valve seat ring or the valve itself must be changed, both together if necessary.

Check valve lag Remove cylinder head Job card W 01-04-04. Install clamping block (1) on clamping plate (2). Mount the cylinder head on the clamping block.

6
1

2
39164 0

Measure valve lag with depth measuring appliance from the valve head to the cylinder head sealing surface.
01 45 01 46

39175 0
11/2004

1/2

0312 1563 - 0138

Cylinder head W 01-07-08

Remove cylinder head from clamping block (1). Remove clamping block from clamping plate (2). Install cylinder head Job card W 01-04-04.

2011

2
39164 0

11/2004

2/2

0312 1563 - 0138

2011
W 02-01-07

Drive system W 02-01-07

Check crankcase
Tools
- Commercial tools Magnetic measuring stand Micrometer gauge Internal measuring device Prisms Hardness tester - Special tools 100 400 - Meter

References
- W 02-04-01

Note
The rework stages are marked on the outer contour of the crankshaft face on the flywheel side. H = ground main bearing pin P = ground con rod bearing pin

Note
If the crankshaft is worn it is possible to have the crankshaft repaired in our Service Centers. Check bearing pin hardness Remove crankshaft Job card W 02-04-01. Place the crankshaft on prisms.

39176 0

Check baring pin with hardness tester.

Note
The measured values must be converted according to the table of the measuring instrument.
02 07

39177 0
11/2004

1/4

0312 1564 - 0138

Drive system W 02-01-07

Note
Schematic representation for measuring the bearing pins at the points 1 and 2 in the levels a and b.

2011

36424 1

Check the diameter of the main bearing pins Measure main bearing pin with micrometer screw.

Note
Measuring points, see schematic diagram

02 03

02 04

02 05

02 06

39178 0

Check the diameter of the lifting bearing journal Measure lifting bearing journal with micrometer gauge.

Note
Measuring points, see schematic diagram

02 22

02 23

02 24

02 25

39179 0
11/2004

2/4

0312 1564 - 0138

2011
Check runout Attach magnetic measuring stand and insert meter. Apply stylus to the main bearing pin with pre-tension (arrow) and set meter to 0. Turn crankshaft evenly and check shells.
02 26

Drive system W 02-01-07

Remove magnetic measuring stand and meter.

39180 0

Measure fit bearing width Set micrometer gauge to 35 mm. Push the internal measuring device between the test surfaces of the micrometer gauge and set to 0.

35825 1

Measure fit bearing width with internal measuring device between the contact surfaces of the starting rings. Note the measured value (dimension A).
02 11 02 12 02 13

Note
The dimension "A" is required for determining the axial clearance.

39181 0
11/2004

3/4

0312 1564 - 0138

Drive system W 02-01-07

Check axial clearance Place startup ring halves on fit bearing cover (arrows). Measure width with micrometer gauge. Note the measured value (dimension B).

2011

Note
The dimension "B" is required for determining the axial clearance.

35827 1

Determine axial clearance Axial clearance = dimension A dimension B

02 34

Example: Dimension "A" = Dimension B Axial clearance 35.00 mm 34.80 mm 0.20 mm

Use the appropriate startup ring halves.

02 35 02 36

Visual inspection Visually inspect the running surfaces (arrows) of the shaft sealing rings. Install crankshaft Job card W 02-04-01.

39182 0
11/2004

4/4

0312 1564 - 0138

2011
W 02-02-02

Drive system W 02-02-02

Renew crankshaft sealing ring (flywheel side)

Tools
- Commercial tools Assembly lever - Special tools 142 860 - Assembly tool

References
- W 12-06-01

Remove crankshaft sealing ring Remove flywheel Job card W 12-06-01. Loosen the crankshaft sealing ring (arrow) in its seat with a pin.

39506 0

Carefully drill a hole (at least 3 mm ) diameter in the crankshaft sealing ring.

Note
- Coat the drill thickly with grease so that no drill chips fall into the crankcase. - Do not damage the rear cover and crankshaft.

39507 0
11/2004

1/4

0312 1565 - 0138

Drive system W 02-02-02

Turn in self-tapping screw (1) with washer.

2011

39508 0

Remove crankshaft sealing ring with suitable tool, e.g. assembly lever. Visually inspect the crankshaft flange and rear cover.

39509 0

Install crankshaft sealing ring Oil the sealing lip of the new crankshaft sealing ring lightly with engine oil. Fit the crankshaft sealing ring (1) to the assembly sleeve (2).

2 1

Note
The sealing lip must face the crankshaft in assembly.

39510 0
11/2004

2/4

0312 1565 - 0138

2011
Note
Installation depthe X = approx. 2.5 mm of the crankshaft sealing ring.

Drive system W 02-02-02

X
39352 0

Drive in crankshaft sealing ring with assembly tool.

Note
Note installation depth. Install flywheel. Job card W 12-06-01.

39511 0

11/2004

3/4

0312 1565 - 0138

Drive system W 02-02-02

Notes

2011

11/2004

4/4

0312 1565 - 0138

2011
W 02-02-04

Drive system W 02-02-04

Renew crankshaft sealing ring (opposite side to flywheel)

Tools
- Commercial tools 9017 - Assembly lever - Special tools 100 700 - Setting bolt 142 850 - Assembly tool

References
- W 03-08-01 - W 04-04-12 old version - W 04-04-12 new version

Remove crankshaft sealing ring Remove toothed belt and clamping roller, loosen camshaft toothed belt wheel Job card W 04-04-12 old version. Job card W 04-04-12 new version. Remove crankshaft toothed wheel Job card W 03-08-01. Loosen crankshaft sealing ring in its seat with a pin.

39650 0

Carefully drill a hole (at least 3 mm ) diameter in the crankshaft sealing ring.

Note
- Coat the drill thickly with grease so that no drill chips fall into the crankcase. - Do not damage the front cover and crankshaft.

39651 0
11/2004

1/4

0312 1566 - 0138

Drive system W 02-02-04

Turn in self-tapping screw (1) with washer.

2011

39652 0

Remove crankshaft sealing ring with suitable tool, e.g. assembly lever. Visually inspect the running surface of the crankshaft flange and front cover.

39653 0

Install crankshaft sealing ring Oil the sealing lip of the new crankshaft sealing ring lightly with engine oil. Fit the crankshaft sealing ring (1) to the assembly tool (2).

1 2

Note
The sealing lip must face the crankshaft in assembly.

39515 0
11/2004

2/4

0312 1566 - 0138

2011
Mount the crankshaft sealing ring with the assembly tool and turn in the screw.

Drive system W 02-02-04

39654 0

Pull in the assembly tool to the stop by turning in the screw.

Note
The installation depth of the crankshaft sealing ring is determined by the assembly tool. Unscrew screw and remove assembly tool. Install crankshaft toothed wheel Job card W 03-08-01. Install toothed belt and clamping roller, fix camshaft toothed belt wheel Job card W 04-04-12 old version. Job card W 04-04-12 new version.
39655 0

11/2004

3/4

0312 1566 - 0138

Drive system W 02-02-04

Notes

2011

11/2004

4/4

0312 1566 - 0138

2011
W 02-03-01

Drive system W 02-03-01

Check con rod

Tools
- Commercial tools Micrometer gauge Internal measuring device Con rod test device 8021 - Socket size 15 - Special tools 100 400 - Meter

References
- W 02-03-03

Note
The con rod is removed and the piston disassembled.

Check piston bolt bush Prepare internal measuring device Mount probe bolt for the appropriate measuring range in the internal measuring device. Mount meter with approx. 1 mm pre-tension in the internal measuring device. Set micrometer gauge to - 26 mm in FL/M engines - 30 mm in BFL/M engines. Balance the internal measuring device between the test surfaces of the micrometer gauge and set the meter to the reversal point of the pointer to 0.
34768 1

Note
Schematic representation for measuring the piston bolt bush at the points a and b in the levels 1 and 2.

37239 0
11/2004

1/8

0312 1567 - 0138

Drive system W 02-03-01

Measure piston bolt bush with internal measuring device. Insert the internal measuring device in the piston bolt bush. Balance the internal measuring device respectively at the given measuring points and read off the measured value at the reversal point of the pointer.

2011

Note
- Piston bolt bush pressed in. - Measuring points, see schematic diagram.
02 43

Remove and install piston bolt bush Job card W 02-03-03.

34770 1

Check diameter of the piston bolt Measure piston bolt with micrometer gauge.
02 61

35908 1

Determine piston bolt clearance

Example:
Dimension "A" = Dimension B Piston bolt clearance 26.035 mm 26.000 mm 0.035 mm

Note
The piston bolt clearance is given by the difference between the piston bolt bush internal diameter "A" and the diameter of the piston bolt "B".
02 45

11/2004

2/8

0312 1567 - 0138

2011
Check the con rod bearing bore Mount con rod bearing cover on con rod.

Drive system W 02-03-01

Note
The numeric identification (1) on the con rod and the con rod bearing cover must be identical and be opposite each other in assembly.

39322 0

Tighten nuts.

Note
Use a twelve-edge box wrench.
02020

39323 0

Prepare internal measuring device Mount probe bolt for the appropriate measuring range in the internal measuring device. Mount meter with approx. 1 mm pre-tension in the internal measuring device. Set micrometer gauge to 58.50 mm. Balance the internal measuring device between the test surfaces of the micrometer gauge and set the meter to the reversal point of the pointer to 0.

36094 1
11/2004

3/8

0312 1567 - 0138

Drive system W 02-03-01

Note
Schematic representation for measuring the con rod bearing bore at the points a and b in the levels 1 and 2.

2011

37239 0

Measure con rod bearing bore with internal measuring device. Insert internal measuring device in the con rod bearing bore. Balance the internal measuring device respectively at the given measuring points and read the measured value at the reversal point of the pointer.

Note
If the measured values deviate slightly, additional measurements must be made with new bearing shells.
02 55

39324 0

Check con rod bearing shell internal diameter Unscrew nuts and remove con rod bearing cover. Insert con rod bearing shell in the con rod.

Note
- Note the assignment of the bearing shells. - The twist protection (1) must engage in the groove (2).

39325 0
11/2004

4/8

0312 1567 - 0138

2011
Insert con rod bearing shell in the appropriate con rod bearing cover.

Drive system W 02-03-01

Note
The twist protection (1) must engage in the groove (2).

39326 0

Mount the con rod bearing cover and tighten the nuts.

Note
The numeric identification (1) on the con rod and the con rod bearing cover must be identical and be opposite each other in assembly.

1
39327 0

Tighten nuts.

Note
Use a twelve-edge box wrench.
02020

39328 0
11/2004

5/8

0312 1567 - 0138

Drive system W 02-03-01

Prepare internal measuring device Mount probe bolt for the appropriate measuring range in the internal measuring device. Mount meter with approx. 1 mm pre-tension in the internal measuring device. Set micrometer gauge to 55 mm. Balance the internal measuring device between the test surfaces of the micrometer gauge and set the meter at the reversal point of the pointer to 0.

2011

36094 1

Note
Schematic representation for measuring the con rod bearing shell internal diameter at the points a and b in the levels 1 and 2.

37239 0

Measure con rod bearing shell internal diameter with internal measuring device. Insert internal measuring device between the con rod bearing shells. Balance the internal measuring device respectively at the given measuring points and read off the measured value at the reversal point of the pointer.

Note
- If the values are up to max. 0.015 mm above the bearing tolerances, the con rod can be used further. - If the wear limit is reached, the con rod has to be changed.
02 52 02 53 02 54

39329 0
11/2004

6/8

0312 1567 - 0138

2011
Determine con rod bearing clearance

Drive system W 02-03-01

Example:
Dimension "A" = Dimension B Con rod bearing clearance 35.00 mm 34.80 mm 0.20 mm

Note
The con rod bearing clearance is given by the difference of the con rod bearing shell internal diameter A and the diameter of the lifting bearing journal B.

02 56

02 57

Unscrew nuts and remove con rod bearing cover.

Check con rod parallelism Check con rod without bearing shells on the con rod test device. Permissible deviation "a" = max. 0.03 mm at a distance of "X" = 100 mm.

35880 1

Check con rod right-angledness Permissible deviation "A" to "B" = max. 0.03 mm at a distance of "X" = 100 mm.

Note
Aligning the con rod is not permissible.

35881 1
11/2004

7/8

0312 1567 - 0138

Drive system W 02-03-01

Notes

2011

11/2004

8/8

0312 1567 - 0138

2011
W 02-03-03

Drive system W 02-03-03

Remove and install piston bolt bush

Tools
- Commercial tools - Special tools 131 340 - Assembly tool for FL/M engines 131 350 - Assembly tool for BF/M engines

Note
- The con rod is removed and the piston disassembled. - The piston bolt bush must be mechanically machined after assembly.

References
- W 02-09-03

Remove piston and con rod Job card W 02-09-03. Remove piston bolt bush Insert extraction socket (1) in piston bolt bush. Place counterbearing (2) with the open side on the con rod and insert the screw (3). Fit washer and tighten nut (4).

6
4

3 2 1

Note
- 131 340 for FL/M engines. - 131 350 for BFL/M engines.

39330 0

Pull out piston bolt bush. Dismantle disassembly tool and remove piston bolt bush.

39331 0
11/2004

1/4

0312 1568 - 0138

Drive system W 02-03-03

Install piston bolt bush Mount piston bolt bush on con rod.

2011

Note
Pay attention to matching of the oil bores (1) in the piston bolt bush and the con rod.

39332 0

Insert extraction socket (1) in new piston bolt bush. Place counterbearing (2) with the closed side on the con rod and insert the screw (arrow). Fit washer and tighten nut.

39333 0

Pull in piston bolt bush flush. Remove disassembly tool. Check matching of oil bores in the piston bolt bush and con rod again.

39334 0
11/2004

2/4

0312 1568 - 0138

2011
Note
The piston bolt bush must be mechanically machined after assembly.
02 61 02 43 02 45

Drive system W 02-03-03

Install piston and con rod Job card W 02-09-03.

33855 1

11/2004

3/4

0312 1568 - 0138

Drive system W 02-03-03

Notes

2011

11/2004

4/4

0312 1568 - 0138

2011
W 02-04-01

Drive system W 02-04-01

Remove and install crankshaft

Tools
- Commercial tools 8021 - Socket size 15

References
- W 02-01-07 - W 02-09-03 - W 03-08-01 - W 03-09-01

Note
Only in FL, FM engines When replacing the crankshaft and/or crankcase, the piston class must be redetermined.

Auxiliary material
- DEUTZ DW 74

Remove crankshaft Remove rear cover (flywheel side) Job card W 03-09-01. Remove front cover (opposite side to flywheel) Job card W 03-08-01. Unscrew screws (1) and remove oil intake pipe (2).

39335 0

Unscrew setting bolts (1) of the crankshaft lock.

39188 0
11/2004

1/10

0312 1569 - 0138

Drive system W 02-04-01

Remove all con rod bearing covers Unscrew nut (1) and remove con rod bearing cover (2).

2011

Note
- Use a twelve-edge box wrench. - Put down the con rod bearing cover in the order of installation, note order of cylinders. - Do not turn the crankshaft. Remove con rod bearing cover and con rod bearing shell.

39336 0

Remove fit bearing and all main bearing covers Unscrew screws (1).

39337 0

Remove fit bearing cover (1), bearing shell and both startup ring halves (arrows). Remove main bearing cover (2) and bearing shells.

Note
Put down the components in the order of installation, note order of cylinders.

39338 0
11/2004

2/10

0312 1569 - 0138

2011
Remove crankshaft.

Drive system W 02-04-01

39339 0

Remove all main bearing shells (1) and all con rod bearing shells (2).

Note
Put down the components in the order of installation, note order of cylinders. Check components for visible signs of wear. Check axial clearance of crankshaft Job card W 02-01-07.

39340 0

Only in FL, FM engines

Note
When replacing the crankshaft and/or crankcase, the distance from the cylinder head sealing surface to the highest point of the lifting bearing pin in UT position must be redetermined to define the piston class. Remove and install pistons and con rod Job card W 02-09-03.

39251 0
11/2004

3/10

0312 1569 - 0138

Drive system W 02-04-01

Install crankshaft Insert main bearing shells in the crankcase.

2011

Note
- Note the assignment of the bearing shell. - The twist protection (1) must engage in the groove (2).

39341 0

Insert main bearing shell in the appropriate main bearing cover.

Note
- Note the assignment of the main bearing cover. - The twist protection (1) must engage in the groove (2).

37043 1

Insert con rod bearing shell in the con rod.

Note
- Note the assignment of the bearing shell. - The twist protection (1) must engage in the groove (2).

39342 0
11/2004

4/10

0312 1569 - 0138

2011
Insert con rod bearing shell in the appropriate con rod bearing cover.

Drive system W 02-04-01

Note
- Note the assignment of the bearing shell. - The twist protection (1) must engage in the groove (2).

39343 0

Check all clamping bushes are in place (arrows).

39344 0

Oil all bearing surfaces on the bearing pin and bearing shells lightly. Insert the crankshaft carefully in the crankcase.

Note
Do not jam the con rods when inserting the crankshaft.

39339 0
11/2004

5/10

0312 1569 - 0138

Drive system W 02-04-01

Stick both startup ring halves with guide lugs (arrow) to the fir bearing cover with a little grease.

2011

Note
- The installation position of the fit bearing cover is given by the numeric identification (1): Number 1 in 2-cylinder Number 2 in 3-cylinder Number 3 in 4-cylinder - The oil groove (2) must face the face mirror of the crankshaft.

2
39345 0

Install fit bearing and main bearing covers Insert fit bearing cover (1) and main bearing cover (2) according to the numbering.

Note
Note assignment and installation position. - Insert bearing cover with number "1" on flywheel side. - The bevel (arrow) must face the front cover.

1
39346 0

Oil lightly and tighten all screws (1) of the fit bearing and main bearing covers.

Note
Screws can be used a max. 3 times in case of provability, otherwise always change them.
02010

39347 0
11/2004

6/10

0312 1569 - 0138

2011
Install all con rod bearing covers Pull the con rods carefully onto the lifting bearing journal.

Drive system W 02-04-01

39348 0

Note
- Note the assignment of the con rod bearing cover. - The numeric identification on the con rod bearing cover and the con rod must be identical and be opposite each other in assembly (1). - The numeric identification is facing the operating side.

39349 0

Tighten nuts.

Note
- Con rod bolts and nuts can be used a max. 5 times in case of provability, otherwise always change them. - Use a twelve-edge box wrench.
02020

39350 0
11/2004

7/10

0312 1569 - 0138

Drive system W 02-04-01

Clean the sealing surface on the oil intake pipe and crankcase. Apply sealant DEUTZ DW 74 to oil suction pipe (arrow).

2011

39351 0

Mount oil intake pipe (2) and tighten screws (1).

Note
Do not move sealant when mounting the oil intake pipe.
08015

39335 0

Screw setting bolts (1) into the crankcase to the stops.

39188 0
11/2004

8/10

0312 1569 - 0138

2011
Turn the crankshaft carefully in the direction of rotation of the engine (clockwise) until it touches the setting bolts. Install rear cover (flywheel side) Job card W 03-09-01. Install front cover (opposite side to flywheel) Job card W 03-08-01.

Drive system W 02-04-01

39130 0

11/2004

9/10

0312 1569 - 0138

Drive system W 02-04-01

Notes

2011

11/2004

10/10

0312 1569 - 0138

2011
W 02-09-03

Drive system W 02-09-03

Remove and install pistons and con rod

Tools
- Commercial tools 8021 - Socket size 15 - Special tools 101 910 - Device 130 630 - Piston ring tensioning band 131 100 - Disassembly tool

References
- W 01-04-04 - W 02-10-03 - W 08-04-06

Notes on piston classes of the pistons When replacing a piston, make sure you use the same piston class.

Note
- The pistons are divided into piston classes by different compression values. - The piston classes are marked on the base of the piston by "A" or "B" (1).

39249 0

Note
- For FL- and FM engines pistons with different compression values are available. - In BFL and BFM-engines pistons with piston class "A" (1) are used exclusively.
20 97

39174 0
11/2004

1/8

0312 1570 - 0138

Drive system W 02-09-03

Remove piston and con rod. Remove cylinder head Job card W 01-04-04. Remove oil intake pipe Job card W 08-04-06. Pull out oil dipstick (1).

2011

1
39219 0

Remove con rod bearing cover Set lifting bearing journal in the lower dead point. Unscrew nuts (1).

Note
- Use a twelve-edge box wrench. - Put down the components in the order of installation, note order of cylinders.
00 81

Remove con rod bearing cover (2) and con rod bearing.

39220 0

Press out piston and con rod.

Note
Set down the components in the order of installation, note cylinder order.

00 81

39221 0
11/2004

2/8

0312 1570 - 0138

2011
Remove con rod bearing shells (1). Check components for visible signs of wear.

Drive system W 02-09-03

1 1
39240 0

Remove piston from con rod. Insert disassembly tool (1) in the piston bolt.

6
1

Caution!
!

Risk of injury! The spring ring jumps off. Always use the disassembly tool.

39244 0

Place suitable tool in recess (1). Remove spring rings (2) on both sides and press out piston bolt (3).

Note
The tools are not inserted for a better representation. Check components for visible signs of wear.

1 2

3
39248 0
11/2004

3/8

0312 1570 - 0138

Drive system W 02-09-03

Only in FL, FM engines Determine piston class

2011

Note
If the crankshaft and/or the crankcase are replaced, the piston class must be redetermined for every single cylinder. Place lifting bearing journal of the respective cylinder in the upper dead point (UT).

39250 0

Measure the distance with the depth measuring appliance, from the cylinder head sealing surface to the highest point of the lifting bearing journal in UT position.

Note
The sealing surface must be clean. Read and note measured value.

39251 0

Select piston class (1) per cylinder.

20 79

Note
In undermeasure steps of the crankshaft 0.125 must be added to the values in the technical data.

39249 0
11/2004

4/8

0312 1570 - 0138

2011
Complete the con rod and the piston Insert a spring ring.

Drive system W 02-09-03

X

Note
- The ring joint must face the piston base, X = +/- 20 - Pay attention to correct fit of the locking ring in the groove.

39257 0

Insert con rod in piston.

6
6010

Note
The symbol flywheel/crankshaft (1), on the piston base, must face left and the numeric identification (2) on the con rod up.

39259 0

Oil lightly and press in the piston bolt. Insert the second spring ring.

Note
- The ring joint must face the piston compression bolt. - Pay attention to correct fit of the spring ring in the groove.

39260 0
11/2004

5/8

0312 1570 - 0138

Drive system W 02-09-03

Install piston and con rod Insert con rod bearing shell in the con rod.

2011

Note
- Note the assignment of the bearing shells. - The twist protection (1) must engage in the groove (2).

39282 0

Insert con rod bearing shell in the appropriate con rod bearing cover.

Note
The twist protection (1) must engage in the groove (2).

39283 0

Arrange piston ring joints offset by about 120. Check piston rings and piston ring grooves Job card W 02-10-03.

36216 1
11/2004

6/8

0312 1570 - 0138

2011
Oil cylinder running surface, piston, piston rings and lifting bearing journal lightly. Clamp piston rings with piston ring tensioning band (1).

Drive system W 02-09-03

Note
Do not turn the piston rings any more.

39284 0

Set lifting bearing journal in the lower dead point.

Note
- Note the cylinder assignment of the piston. - Note the identification (1) of the installation position on the piston base, the symbol flywheel/crankshaft must face the flywheel. - The piston ring tensioning band must lie flat on the crankcase. Push the piston into the cylinder with the con rod.

39285 0

Press the con rod carefully against the lifting journal.

Note
Do not jam the con rod with the crankshaft.

39286 0
11/2004

7/8

0312 1570 - 0138

Drive system W 02-09-03

Install the con rod bearing cover.

2011

Note
- Note the assignment of the con rod bearing cover. - The numeric identifications (1) on the con rod and the con rod bearing cover must be identical and opposite each other when assembled. - The numeric identification is facing the operating side.

39287 0

Tighten nuts.

Note
- Con rod bolts and nuts can be used a max. 5 times in case of provability, otherwise always change them. - Use a twelve-edge box wrench.
02020

39290 0

Insert oil dipstick (1). Install oil intake pipe. Job card W 08-04-06. Install cylinder head Job card W 01-04-04.

1
39219 0
11/2004

8/8

0312 1570 - 0138

2011
W 02-09-07

Drive system W 02-09-07

Check piston
Tools
- Commercial tools Micrometer gauge Internal measuring device - Special tools 100 400 - Meter

References
- W 02-09-03

Note
If the wear limit is reached, the piston has to be changed.

Check the piston bolt bore Remove piston from con rod. Job card W 02-09-03.

39054 0

Prepare internal measuring device Mount probe bolt for the appropriate measuring range in the internal measuring device. Mount meter with approx. 1 mm pre-tension in the internal measuring device. Set micrometer gauge to - 26 mm in FL/M engines - 30 mm in BFL/M engines. Balance the internal measuring device between the test surfaces of the micrometer gauge and set the meter to the reversal point of the pointer to 0.

34768 1
11/2004

1/4

0312 1571 - 0138

Drive system W 02-09-07

Note
Schematic representation for measuring the piston bolt bore at the points a and b in the levels 1 and 2.

2011

37239 0

Measure piston bolt bore with internal measuring device. Insert the internal measuring device in the piston bolt bush. Balance the internal measuring device respectively at the given measuring points and read off the measured value at the reversal point of the pointer.

Note
Measuring points, see schematic diagram.
02 78

36484 1

Check the piston diameter

Note
Schematic representation for measuring the piston diameter at the measuring points 1, 2 and 3, transverse to the piston bolt bore.

3 2 1

37244 0
11/2004

2/4

0312 1571 - 0138

2011
Measure piston diameter with micrometer gauge.

Drive system W 02-09-07

Note
Measuring points, see schematic diagram.
02 71 02 72 02 73

Complete the con rod with piston Job card W 02-09-03.

39055 0

11/2004

3/4

0312 1571 - 0138

Drive system W 02-09-07

Notes

2011

11/2004

4/4

0312 1571 - 0138

2011
W 02-10-03

Drive system W 02-10-03

Check piston rings and piston ring grooves

Tools
- Commercial tools Feeler gauges - Special tools 130 300 - Universal piston ring pliers 130 420 - Trapezoidal wear gauge

References
- W 02-09-03

Check piston rings and piston ring grooves Remove piston from con rod. Job card W 02-09-03. Set universal piston ring pliers to the piston diameter.
02 71

Remove piston rings with universal piston ring pliers.

39212 0

Clean and inspect the pistons and ring grooves.

39213 0
11/2004

1/4

0312 1572 - 0138

Drive system W 02-10-03

Only in BFL, BFM engines Measure piston ring trapezoidal groove for first piston ring with trapezoidal groove wear gauge.

2011

33866 1

If there is a gap (S) between the trapezoidal wear gauge and piston, the piston is still usable.

33867 1

If the trapezoidal groove wear gauge is touching the piston (arrow), the piston must be changed.

33868 1
11/2004

2/4

0312 1572 - 0138

2011
Check the piston ring joint clearance Insert the piston ring (1) in the cylinder.

Drive system W 02-10-03

Note
Align the piston ring in the cylinder by pushing the piston.

39214 0

Measure the piston ring joint clearance with a feeler gauge.

Note
If the wear limit is reached, change the piston ring.
02 84 02 85 02 86

39215 0

Install piston rings.

Note
- Order and position of the piston rings seen from the piston base. - On the piston rings (1, 2 and 3) the identification Top must face the combustion chamber. Rectangular ring in FL/M engines. Double trapeze ring for BFL/M engines. Minute ring. Roof chamfer ring with hose spring.

1 2 3

1. 1. 2. 3.

39216 0
11/2004

3/4

0312 1572 - 0138

Drive system W 02-10-03

Install rings with universal piston ring pliers.

2011

Note
Set spring joint of the roof chamfer ring 180 to the ring joint.

39217 0

Check the piston ring axial clearance Measure piston ring axial clearance in the piston ring groove with a feeler gauge.

Note
- Do measurement with new piston rings. - In BF engines, only check axial clearance with feeler gauge in piston ring groove 2 and 3. - If the wear limit is reached, the piston has to be changed.
02 87 02 88 02 89

39218 0

Mount piston on con rod Job card W 02-09-03.

11/2004

4/4

0312 1572 - 0138

2011
W 02-15-01

Drive system W 02-15-01

Remove and install piston cooling nozzles

Tools
- Commercial tools

References
- W 02-04-01

Remove piston cooling nozzles Remove crankshaft Job card W 02-04-01. Press out piston cooling nozzle (1) with a suitable tool (2).

39210 0

Install piston cooling nozzles Clean bores for piston cooling nozzles in the crankcase. Press in piston cooling nozzle (1) with suitable tool to the stop. Install crankshaft Job card W 02-04-01.

39211 0
11/2004

1/2

0312 1573 - 0138

Drive system W 02-15-01

Notes

2011

11/2004

2/2

0312 1573 - 0138

2011
W 03-01-11

Crankcase W 03-01-11

Remove and install crankcase bleeding

Tools
- Commercial tools

Remove bleed valve Unscrew screw (1) and remove bleed valve (2). Clean components and check for visible signs of wear.

39028 0

Pull new round sealing ring (1) onto bleed valve (2).

2 1

39029 0
11/2004

1/4

0312 1574 - 0138

Crankcase W 03-01-11
Install bleed valve Mount bleed valve (2) and press in.

2011

Note
The bleed valve must contact the front cover evenly. Tighten screw (1).

2
03060

39028 0

In BFL, BFM engines Remove bleed valve Unscrew screw (1) and remove bleed valve (2). Clean components and check for visible signs of wear.

34038 1

Pull new round sealing ring (1) onto bleed valve (2).

2 1

39029 0
11/2004

2/4

0312 1574 - 0138

2011
Install bleed valve Mount bleed valve (1) and press in.

Crankcase W 03-01-11

Note
The bleed valve must touch the cylinder head cover evenly. Tighten screw.
03060

34163 1

11/2004

3/4

0312 1574 - 0138

Crankcase W 03-01-11
Notes

2011

11/2004

4/4

0312 1574 - 0138

2011
W 04-03-01

Engine control W 04-03-01

Renew camshaft sealing ring (opposite side to flywheel)

Tools
- Commercial tools 9017 - Assembly lever - Special tools 142 050 - Press-in device

References
- W 04-04-12 (old version) - W 04-04-12 (new version)

Remove camshaft sealing ring Remove toothed belt and clamping roller, loosen camshaft toothed belt wheel Job card W 04-04-12(old version) Job card W 04-04-12(new version)

2 1

Unscrew center screw (1) with washer (2) and remove the camshaft toothed belt wheel (3).

Note
There is no washer (2) on the camshaft toothed belt wheel with torsional vibration damper.

39243 0

Loosen crankshaft sealing ring in its seat by hitting with a mandrel.

39656 0
11/2004

1/4

0312 1582 - 0138

Engine control W 04-03-01

Carefully drill a hole (at least 3 mm ) diameter in the crankshaft sealing ring.

2011

Note
- Coat the drill thickly with grease so that no drill chips fall into the crankcase. - Do not damage the front cover and crankshaft.

39657 0

Turn in self-tapping screw (1) with washer.

39658 0

Pull out crankshaft sealing ring with assembly lever. Visually inspect the running surface of the crankshaft flange and front cover.

39659 0
11/2004

2/4

0312 1582 - 0138

2011
Install camshaft sealing ring Oil the sealing lip of the new camshaft sealing ring lightly with engine oil. Fit the camshaft sealing ring (1) to the assembly tool (2).

Engine control W 04-03-01

1 2

Note
The sealing lip must face the camshaft in assembly.

39515 0

Mount the camshaft sealing ring with the assembly tool and turn in the screw.

39660 0

Pull in the assembly tool to the stop by turning in the screw.

Note
The installation depth of the crankshaft sealing ring is determined by the assembly tool. Unscrew screw and remove assembly tool.

39661 0
11/2004

3/4

0312 1582 - 0138

Engine control W 04-03-01

Mount camshaft toothed belt wheel (3) and tighten center screw (1) with washer (2).

2011

Note
- There is no washer (2) on the camshaft toothed belt wheel with torsional vibration damper. - All connections must be clean and oil free. Install toothed belt and clamping roller, fix camshaft toothed belt wheel. Job card W 04-04-12 (old version) Job card W 04-04-12 (new version)

2 1

39243 0

11/2004

4/4

0312 1582 - 0138

2011
W 03-03-01

Crankcase W 03-03-01

Check cylinder
Tools
- Commercial tools Internal measuring device Micrometer gauge - Special tools 100 400 - Meter

Note
- The crankshaft bearing cover must be mounted properly to measure the cylinder. - If the wear limit is reached, it is possible to rework the crankshaft for further use. Use pistons and piston rings according to the repair stage.

References
- W 01-04-04

Remove cylinder head Job card W 01-04-04. Check cylinder Check cylinder for visible signs of wear.

39239 0

Check the cylinder running surface Prepare internal measuring device. Mount probe bolt for the appropriate measuring range in internal measuring device. Install meter with approx. 1 mm pre-tension in the internal measuring device. Set micrometer gauge to 94 mm. Balance internal measuring device between the test surfaces of the micrometer gauge and set the meter at the reversal point of the pointer to 0.

36094 1
11/2004

1/2

0312 1575 - 0138

Crankcase W 03-03-01
Note
Schematic representation for measuring the cylinder running surface at the points a and b in the levels 1 - 3".

2011

1
a b

2
a b

39100 0

Measure cylinder with internal measuring device. Insert internal measuring device in the cylinder. Balance the internal measuring device respectively at the given measuring points and read off the measured value at the reversal point of the pointer.

Note
Measuring points, see schematic diagram.
03 31 03 41 03 32 03 42

Install cylinder head Job card W 01-04-04.

39241 0

11/2004

2/2

0312 1575 - 0138

2011
W 03-08-01

Crankcase W 03-08-01

Remove and install front cover (opposite side to flywheel)

Tools
- Commercial tools 8036 - Socket 8049 - Force multiplier 8189 - Torx tool kit - Special tools 142 850 - Assembly tool 143 420 - Holder 143 430 - Intermediate disc

Auxiliary material
DEUTZ DW 67

References
- W 04-03-01 - W 04-04-12(new version) - W 04-04-12 (old version) - W 08-04-05 - W 08-08-02

Remove front cover Remove toothed belt and clamping roller, loosen camshaft toothed belt wheel Job card W 04-04-12(new version) Job card W 04-04-12(old version)

2 1

Remove camshaft toothed belt wheel Unscrew center screw (1) with washer (2) and remove the camshaft toothed belt wheel (3).

Note
There is no washer (2) on the camshaft toothed belt wheel with torsional vibration damper.
39243 0

Remove crankshaft toothed wheel. Mount intermediate disc.

Note
The fixing bolts (1) must engage the bores (2).

1
39374 0
11/2004

1/12

0312 1576 - 0138

Crankcase W 03-08-01
Mount holder.

2011

Note
- The fixing bolts (1) must engage the bores (2). - Do not turn the crankshaft.

39375 0

Tighten screws (1).

Note
Do not turn the crankshaft.

39293 0

Mount force multiplier with socket.

Note
Snap in setting bolts (1) in CCW position.

39294 0
11/2004

2/12

0312 1576 - 0138

2011
Hold the force multiplier and loosen the center screw. Remove the force multiplier, holder and intermediate disc.

Crankcase W 03-08-01

39460 0

Unscrew center screw (1) and remove toothed wheel (2).

Note
An adapter is used in place of the toothed wheel without a hydraulic pump mounted.

39295 0

Remove crankshaft toothed wheel (1). Remove lube oil pump Job card W 08-04-05.

39296 0
11/2004

3/12

0312 1576 - 0138

Crankcase W 03-08-01
Unscrew screws (1) and remove hydraulic pump console with hydraulic pump.

2011

39297 0

Unscrew screw (1) and remove cable plug (2) from engine shutdown. Pull out cable plug (3) from lifting magnet for start volume release. Remove lube oil tray Job card W 08-08-02.

1 2

39298 0

Unscrew screws (arrows) and remove front cover. Check components for visible signs of damage.

39299 0
11/2004

4/12

0312 1576 - 0138

2011
Install front cover Knock out crankshaft sealing ring (1).

Crankcase W 03-08-01

Note
Do not damage the sealing surface when knocking out. Clean the sealing surfaces on the front cover and crankcase.

39527 0

Oil the sealing lip of the new crankshaft sealing ring lightly with engine oil. Fit the crankshaft sealing ring (1) to the assembly sleeve(2).

6
1 2

Note
The sealing lip must face the crankshaft in assembly.

39515 0

Drive in crankshaft sealing ring with assembly tool. Press in assembly tool to stop.

Note
The installation depth of the crankshaft sealing ring is determined by the assembly tool.

33948 1
11/2004

5/12

0312 1576 - 0138

Crankcase W 03-08-01
Coat sealing surface of the front cover with sealant DEUTZ DW 67.

2011

Note
The connection between the camshaft pin and the centrifugal force regulator must be clean and free of oil. Turn engine 180.

Note
The oil tray sealing surface on the crankcase must face up.

34110 1

Mount the front cover with shaft sealing ring and tighten the screws. Align the front cover flush with the oil tray sealing surface (arrows).

Note
- The sealing lips of the shaft sealing rings (1) must touch the bearing journal all round. - Do not tighten screws.

39450 0

Tighten the screws in the tightening order.

03020

Install the lube oil tray Job card W 08-08-02.

34112 1
11/2004

6/12

0312 1576 - 0138

2011
Plug the cable plug (2) to the engine shutdown and tighten the screw (1). Plug the cable plug (3) to the lifting magnet for start volume release.

Crankcase W 03-08-01

1 2

39298 0

Clean the sealing surface on the hydraulic pump console and crankcase. Insert new round sealing ring (arrow).

39451 0

Check all clamping sleeves are in place (arrows).

39452 0
11/2004

7/12

0312 1576 - 0138

Crankcase W 03-08-01
Mount the hydraulic pump console and tighten the screws.

2011

Note
Note different screw length: Screw M10 x 75 mm (1) Screws M10 x 90 mm (2)

39668 0

Tighten screws (1).

12057

Install lube oil pump Job card W 08-04-05. Renew camshaft sealing ring Job card W 04-03-01.

39297 0

Install crankshaft toothed wheel Mount crankshaft toothed wheel (1).

Note
All connections must be clean and oil free.

39453 0
11/2004

8/12

0312 1576 - 0138

2011
Mount toothed wheel (1) for hydraulic pump.

Crankcase W 03-08-01

Note
- An adapter is used in place of the toothed wheel without a hydraulic pump mounted. - All connections must be clean and oil free.

39454 0

Tighten the center screw (1).

Note
Use new screw.

39455 0

Pre-tighten center screw.

02015

39456 0
11/2004

9/12

0312 1576 - 0138

Crankcase W 03-08-01
Mount intermediate disc.

2011

Note
The fixing bolts (1) must engage the bores (2).

1
39374 0

Mount holder.

Note
- The fixing bolts (1) must engage the bores (2). - Do not turn the crankshaft.

39375 0

Tighten screws (1).

Note
Do not turn the crankshaft.

39293 0
11/2004

10/12

0312 1576 - 0138

2011
Mount force multiplier with socket.

Crankcase W 03-08-01

Note
Snap in setting bolts (1) in CW position.

39457 0

Turn the ratchet (1) of the force multiplier to the stop (arrow). Set scale dial (2) to "0".

1
39458 0

Hold the force multiplier and tighten the center screw.

02015

39459 0
11/2004

11/12

0312 1576 - 0138

Crankcase W 03-08-01
Hold the force multiplier to counter (arrows), press setting bolts (1) and release force multiplier.

2011

Caution!
!

Danger of injury when removing an unreleased force multiplier.

Remove the force multiplier with socket, holder and intermediate disc.

39669 0

Install camshaft toothed belt wheel Mount camshaft toothed belt wheel (3) and tighten center screw (1) with washer (2).

Note
- There is no washer (2) on the camshaft toothed belt wheel with torsional vibration damper. - All connections must be clean and oil free.

2 1

39243 0

Install toothed belt and clamping roller, fix camshaft toothed belt wheel Job card W 04-04-12(new version) Job card W 04-04-12(old version)

11/2004

12/12

0312 1576 - 0138

2011
W 03-08-03

Crankcase W 03-08-03

Dismantle and complete front cover (Speed governor with torque adjustment)
Tools
- Commercial tools Depth-measuring appliance - Special tools 100 400 - Meter 100 750 - Measuring device

References
- W 03-08-01

Note
Distinguishing mark for a speed governor with torque adjustment: Adjustment capsule with clamping claw (1) in place of a full load volume stop.

39629 0

Dismantle front cover Remove front cover Job card W 03-08-01. Unscrew screw (1) and remove bleed valve (2).

39261 0
11/2004

1/24

0312 1577 - 0138

Crankcase W 03-08-03
Unscrew screws (1) and remove lifting magnet (2).

2011
1

39262 0

Unscrew screws (1) and remove cap (2) with gasket.

2
1

39263 0

Unhook regulator spring (1).

1
39631 0
11/2004

2/24

0312 1577 - 0138

2011
Unscrew nuts (1). Remove controller lever shaft with roller lever (2) and adjustment lever (3).

Crankcase W 03-08-03
2

39632 0

Remove shims (1).

Note
Pay attention to number and arrangement.

39633 0

Remove centrifugal force measuring mechanism (1).

39634 0
11/2004

3/24

0312 1577 - 0138

Crankcase W 03-08-03
Unscrew nut (1) and remove clamping claw (2). Unscrew idling capsule (3) and remove spring (4).

2011

39637 0

Unscrew nut (1) and remove clamping claw (2).

1 2

39635 0

Unscrew adjustment capsule (1).

39336 0
11/2004

4/24

0312 1577 - 0138

2011
For speed governor with minus adjustment Remove locking ring (1) and deflector lever (2).

Crankcase W 03-08-03

39269 0

Unscrew lifting magnet for start volume release (1).

6
1

39270 0

Remove locking ring (1). Pull out actuating lever (2), remove spring and washer.

2 1

39530 0
11/2004

5/24

0312 1577 - 0138

Crankcase W 03-08-03
Unhook spring from stop (arrow).

2011

39529 0

Knock out clamping pin (1), remove shutoff lever (2) and disc.

39528 0

Remove guide bush (1) and round sealing ring (2). Pull out shutoff shaft (3).

39056 0
11/2004

6/24

0312 1577 - 0138

2011
For speed governor with minus adjustment Unscrew nut (1) and remove washer.

Crankcase W 03-08-03

39272 0

Knock out clamping pin (1).

Note
Mark the installation position of the eccenter shaft (2) before removing.

39467 0

Pull out eccenter shaft (1). Remove guide bush (2) and round sealing ring (3).

39063 0
11/2004

7/24

0312 1577 - 0138

Crankcase W 03-08-03
Remove locking bolt (arrow).

2011

Note
Do not damage the sealing surface on the front cover.

33928 1

Knock out clamping pin (1).

Note
Do not jam the clamping pin in the cover when knocking out.

39470 0

Insert the speed adjustment lever (1) with shaft, guide bush and round sealing ring. Remove adjustment lever (2).

39273 0
11/2004

8/24

0312 1577 - 0138

2011
Unscrew lock nut (1) and turn out setting screw for minimum speed (2). Check components for visible signs of damage.

Crankcase W 03-08-03

39274 0

Complete front cover Turn in setting screw for minimum speed (2) and put on lock nut (1).

39274 0

Set setting screw (1) for minimum speed to dimension "X".

05 05

Note
The setting dimension X only serves as a basic setting. A test stand run is necessary for the performance and speed setting. Tighten lock nut (2).
05005

33950 1
11/2004

9/24

0312 1577 - 0138

Crankcase W 03-08-03
Insert the speed adjustment lever (1) with shaft, guide bush and new round sealing ring.

2011

Note
Oil the speed adjustment shaft lightly.

39469 0

Insert adjustment lever (1) with clamping pin.

Note
Note the installation position, the hole for hooking in the regulator spring (arrow) must face the outside of the front cover. Press the speed adjustment shaft (2) into the front cover to the stop.

39209 0

Drive in clamping pin (1) flush with the adjustment lever.

Note
The bore in the speed adjustment shaft must match up with the bore in the adjustment lever.

39470 0
11/2004

10/24

0312 1577 - 0138

2011
Knock in the locking bolt (arrow) to the stop.

Crankcase W 03-08-03

Note
The groove in the speed adjustment shaft must match up with the bore in the front cover.

33960 1

For speed governor with minus adjustment Oil lightly and insert the eccenter shaft (1).

39471 0

Drive in clamping pin (1) flush with the front cover.

Note
The groove in the eccenter shaft must match up with the bore for he clamping pin.

39478 0
11/2004

11/24

0312 1577 - 0138

Crankcase W 03-08-03
Put on new round sealing ring (1) and guide bush (2).

2011

Note
Oil round sealing ring lightly.

39472 0

Fit washer and tighten nut (1). Position the eccenter shaft at the mark made before removal. Tighten nut (1).
05024

39272 0

Insert shutoff shaft, pre-tension spring (1) and hang into stop (arrow).

Note
- Note installation position. - Oil the shutoff shaft lightly.

39473 0
11/2004

12/24

0312 1577 - 0138

2011
Put on new round sealing ring (1) and guide bush (2).

Crankcase W 03-08-03

Note
Oil round sealing ring lightly.

39474 0

Press the shutoff shaft into the front cover inlet. Put on washer (1) and shutoff lever (2) with clamping pin.

Note
Note installation position of the shutoff lever.

2 1

39475 0

Drive in clamping pin (arrow) flush with the shutoff lever.

Note
The bore in the shutoff shaft must match up with the bore in the shutoff lever.

39466 0
11/2004

13/24

0312 1577 - 0138

Crankcase W 03-08-03
For speed governor with minus adjustment Insert actuating lever (1), spring and washer.

2011

Note
Note installation position of the actuating lever.

39476 0

Put on locking ring (1).

Note
Pay attention to correct fit of the locking ring in the groove.

39464 0

Tighten lifting magnet for start volume release (1) with new round sealing ring.
05065

39270 0
11/2004

14/24

0312 1577 - 0138

2011
Remove deflector lever (2) and locking ring (1).

Crankcase W 03-08-03

Note
- Note installation position of the deflector lever. - Pay attention to correct fit of the locking ring in the groove.

39269 0

Insert centrifugal force measuring mechanism (1).

Note
Do not damage the sealing lip of the shaft sealing ring.

39634 0

Measure and set the parallelism of the roller lever. Place shim discs of at least 0.3 mm on the stud bolts (1).

39633 0
11/2004

15/24

0312 1577 - 0138

Crankcase W 03-08-03
Insert regulator lever shaft with roller lever (1) and tighten nuts (2).
05021

2011
2 1

Note
Note the installation position of the regulator lever shaft, the side with the long cut-out X must face the opening for the lube oil pump and the shim disc.

X
39277 0

Place shims underneath the contact surface of the roller lever (1) so that the ball bearings do not touch the muff (arrows)

39278 0

Insert meter in measuring bridge and position the stylus with pre-tension on the ball bearing (1). Adjust meter to "0".

39279 0
11/2004

16/24

0312 1577 - 0138

2011
Move the measuring bridge and position the stylus on the ball bearing (1). Read and note measured value.

Crankcase W 03-08-03

Note
The difference between both measured values is max. 0.05 mm. To achieve the required tolerance shims of max. 0.5 mm may be placed under one stud bolt.

39280 0

Compensate the tolerance by using shim discs (1) of suitable thickness. Repeat the measuring process after setting.

39633 0

Unscrew nuts and remove regulator lever shaft. Push the adjustment lever (1) onto the regulator lever shaft (2).

Note
Note installation position of the adjustment lever.

1
33967 1

11/2004

17/24

0312 1577 - 0138

Crankcase W 03-08-03
Remove regulator lever shaft with roller lever (2) and adjustment lever (3). Tighten nuts (1).
05021

2011
2

Note
Note installation position of the regulator lever shaft.

39632 0

Hook in regulator spring (1).

1
39631 0

Visually inspect the components of the adjustment capsule, renew if necessary.

33940 1
11/2004

18/24

0312 1577 - 0138

2011
Pre-assemble the adjustment capsule Turn in the spring pre-tensioner (1) to the stop in the housing (2) with max. 1 Nm. Turn out the spring pre-tensioner 1 + 0.5 turns again. Tighten lock nut (3).
05006

Crankcase W 03-08-03

33941 0

Turn in setting screw (2) to the stop on the pressure capsule (1). Turn out the setting screw 1 turn again. Tighten lock nut (3).
05008

2 3

33942 1

Fit new round sealing ring (arrow) onto adjustment capsule.

Note
Oil round sealing ring lightly.

39463 0
11/2004

19/24

0312 1577 - 0138

Crankcase W 03-08-03
Screw in adjustment capsule (1).

2011

39636 0

Measure screw-in depth "X" of the adjustment capsule with depth measuring appliance from the front cover to the housing.
05 06

Note
- If necessary, correct the screw-in depth of the adjustment capsule. - The setting dimension "X" only serves for basic setting, a test stand run is necessary for the exact setting.

33944 1

Insert clamping claw (2) and tighten nut (1).

05023

1 2

39635 0
11/2004

20/24

0312 1577 - 0138

2011
Fit new round sealing ring (arrow) onto idling.

Crankcase W 03-08-03

Note
Oil round sealing ring lightly.

39477 0

Insert spring (1) and turn in idling capsule (2) flush with the inside edge of the front cover (arrow).

2 1

34002 1

Insert clamping claw (1) and tighten nut (2).

Note
Note installation position of the clamping claw.

05022

2
39264 0
11/2004

21/24

0312 1577 - 0138

Crankcase W 03-08-03
Mount cover (2) with new gasket and tighten screws (1).
05025

2011

2
1

39263 0

Pull new round sealing ring (1) onto lifting magnet.

39036 0

Insert lifting magnet (2) and tighten screws (1).

1
05041

39262 0
11/2004

22/24

0312 1577 - 0138

2011
Pull new round sealing ring (1) onto bleed valve (2).

Crankcase W 03-08-03

2 1

39029 0

Mount bleed valve (2) and press in.

6
1

Note
The bleed valve must contact the front cover evenly. Tighten screw (1).

2
03060

Install front cover Job card W 03-08-01.

39261 0

11/2004

23/24

0312 1577 - 0138

Crankcase W 03-08-03
Notes

2011

11/2004

24/24

0312 1577 - 0138

2011
W 03-08-03

Crankcase W 03-08-03

Dismantle and complete front cover (Speed governor without torque adjustment)
Tools
- Commercial tools Depth-measuring appliance - Special tools 100 400 - Meter 100 750 - Measuring device

References
- W 03-08-01

Note
Distinguishing mark for a speed governor without torque adjustment: Full load volume stop (arrow) in place of adjustment capsule.

33931 1

Dismantle front cover Remove front cover Job card W 03-08-01. Unscrew screw (1) and remove bleed valve (2).

39261 0
11/2004

1/18

0312 1578 - 0138

Crankcase W 03-08-03
Unscrew screws (1) and remove lfiting magnet (2).

2011

33914 1

Unscrew screws (1) and remove cap (arrow) with gasket.

33926 1

Unhook regulator spring (1).

33915 1
11/2004

2/18

0312 1578 - 0138

2011
Unscrew nuts (arrows). Remove controller lever shaft with roller lever (1) and adjustment lever (2).

Crankcase W 03-08-03

33916 1

Remove shim discs (arrow).

Note
Pay attention to number and arrangement.

33917 1

Remove centrifugal force measuring mechanism (1).

33918 1
11/2004

3/18

0312 1578 - 0138

Crankcase W 03-08-03
Unscrew nut (1) and remove clamping claw (2). Unscrew idling capsule (3) and remove (4) spring.

2011

39637 0

Unhook spring from stop (arrow).

33921 1

Drive out clamping pin.

33922 1
11/2004

4/18

0312 1578 - 0138

2011
Remove shutoff lever (1) and guide bush.

Crankcase W 03-08-03

33923 1

Pull out shutoff shaft (1) with spacing bush and spring.

6
1

33924 1

Remove round sealing ring (arrow).

33925 1
11/2004

5/18

0312 1578 - 0138

Crankcase W 03-08-03
Knock out clamping pin (1).

2011

1
33927 1

Remove locking bolt (arrow).

Note
Do not damage the sealing surface on the front cover.

33928 1

Pull out the speed adjustment lever (1) with shaft and guide bush, remove the adjustment lever (2).

1 2

33929 1
11/2004

6/18

0312 1578 - 0138

2011
Remove round sealing ring (arrow).

Crankcase W 03-08-03

33930 1

6
Loosen lock nut (arrows). Unscrew setting screw for shutoff stop (1), full load stop (2) and minimum speed (3). Check components for visible signs of damage.

1 2

3
39203 0

Complete front cover Screw in setting screw for shutoff stop (1), minimum speed (2) and full load stop (3).

1 3

Note
Renew round sealing ring on full load stop. Screw on lock nuts.

33938 1
11/2004

7/18

0312 1578 - 0138

Crankcase W 03-08-03
Set setting screw (1) for full load stop to dimension "X".
05 04

2011
2

Tighten lock nut (2).

05004

33939 1

Screw in setting screw (1) for shutoff stop so that the lock nut is flush with the end of the bolt (arrows). Tighten lock nut.
05007

1
33949 1

Set setting screw (1) for minimum speed to dimension "X".

05 05

Note
The setting dimension X only serves as a basic setting. A test stand run is necessary for the performance and speed setting. Tighten lock nut (2).
05005

33950 1
11/2004

8/18

0312 1578 - 0138

2011
Push the spacer bush (arrow) and spring onto the shutoff shaft.

Crankcase W 03-08-03

33951 1

Insert shutoff shaft and hook in spring.

Note
- Note installation position. - Oil the shutoff shaft lightly.

33952 1

Insert new round sealing ring (1).

Note
Oil round sealing ring lightly.

33953 1
11/2004

9/18

0312 1578 - 0138

Crankcase W 03-08-03
Insert guide bush (1).

2011

33954 1

Press the shutoff shaft into the front cover to the stop. Push on shutoff lever with clamping pin.

Note
Note installation position of the shutoff lever.

33955 1

Drive in clamping pin flush with the shutoff lever.

Note
The bore in the shutoff shaft must match up with the bore in the shutoff lever.

33955 1
11/2004

10/18

0312 1578 - 0138

2011
Insert new round sealing ring (1).

Crankcase W 03-08-03

Note
Oil round sealing ring lightly.

1
33956 1

Insert the speed adjustment lever (1) with shaft and guide bush (2).

Note
- Oil the speed adjustment shaft lightly. - Observe the installation position of the speed adjustment lever.

33957 1

Insert adjustment lever (1) with clamping pin.

Note
Note the installation position, the hole for hooking in the regulator spring (arrow) must face the outside of the front cover. Press the speed adjustment shaft (2) into the front cover to the stop.

39057 0
11/2004

11/18

0312 1578 - 0138

Crankcase W 03-08-03
Drive in clamping pin (1) flush with the adjustment lever.

2011

Note
The bore in the speed adjustment shaft must match up with the bore in the adjustment lever.

1
33959 1

Knock in the locking bolt (arrow) to the stop.

Note
The groove in the speed adjustment shaft must match up with the bore in the front cover.

33960 1

Insert centrifugal force measuring mechanism (1).

Note
Do not damage the sealing lip of the shaft sealing ring.

33962 1
11/2004

12/18

0312 1578 - 0138

2011
Measure and set the parallelism of the roller lever. Place shim discs of at least 0.3 mm on the stud bolts (1).

Crankcase W 03-08-03

33963 1

Insert regulator lever shaft with roller lever (1) and tighten nuts (2).
05021

6
2 1

Note
Note the installation position of the regulator lever shaft, the side with the long cut-out X must face the opening for the lube oil pump and the shim disc.

X
39277 0

Place shims underneath the contact surface of the roller lever (1) so that the ball bearings do not touch the muff (arrows).

39278 0
11/2004

13/18

0312 1578 - 0138

Crankcase W 03-08-03
Insert meter in measuring bridge and position the stylus with pre-tension on the ball bearing (1). Adjust meter to "0".

2011

1
33965 1

Move the measuring bridge and position the stylus on the ball bearing (1). Read and note measured value.

Note
The difference between both measured values is max. 0.05 mm. To achieve the required tolerance shims of max. 0.5 mm may be placed under one stud bolt.

1
33966 1

Compensate the tolerance by using shim discs (1) of suitable thickness. Repeat the measuring process after setting.

33963 1
11/2004

14/18

0312 1578 - 0138

2011
Unscrew nuts and remove regulator lever shaft. Push the adjustment lever (1) onto the regulator lever shaft (2).

Crankcase W 03-08-03

Note
Note installation position of the adjustment lever.

1
33967 1

Insert regulator lever shaft with roller lever and adjustment lever. Tighten nuts.
05021

Note
Note installation position of the regulator lever shaft.

33968 1

Hook in regulator spring (1).

33969 1
11/2004

15/18

0312 1578 - 0138

Crankcase W 03-08-03
Fit new round sealing ring (arrow) onto idling capsule.

2011

Note
Oil round sealing ring lightly.

39477 0

Insert spring (1) and turn in idling capsule (2) flush with the inside edge of the front cover (arrow).

2 1

34002 1

Insert clamping claw (1) and tighten nut (2).

Note
Note installation position of the clamping claw.

05022

2
39264 0
11/2004

16/18

0312 1578 - 0138

2011
Mount cover (1) with new gasket and tighten screws (2).
05025

Crankcase W 03-08-03

33970 1

Pull new round sealing ring (1) onto lifting magnet.

6
1

33971 1

Insert lifting magnet and tighten screws.

Note
Note installation position of the lifting magnet.

05041

33972 1
11/2004

17/18

0312 1578 - 0138

Crankcase W 03-08-03
Pull new round sealing ring (1) onto bleed valve.

2011

2 1

39029 0

Mount bleed valve (1) and press in.

Note
The bleed valve must contact the front cover evenly. Tighten screw.
03060

Install front cover Job card W 03-08-01.

33974 1

11/2004

18/18

0312 1578 - 0138

2011
W 03-09-01

Crankcase W 03-09-01

Remove and install rear cover (flywheel side)

Tools
- Commercial tools - Special tools 142 860 - Assembly tool

References
- W 03-09-04 - W 08-04-07

Auxiliary material
- DEUTZ DW 67

Remove rear cover (flywheel side) Remove connection housing Job card W 03-09-04. Remove oil tray Job card W 08-04-07. Unscrew screws (arrows) and remove rear cover (1).

6
1

39031 0

Renew crankshaft sealing ring Knock out crankshaft sealing ring (1).

Note
- Do not damage the sealing surface when knocking out. Check the rear cover visually, renew if necessary.

39512 0
11/2004

1/4

0312 1579 - 0138

Crankcase W 03-09-01
Oil the sealing lip of the new crankshaft sealing ring lightly with engine oil. Fit the crankshaft sealing ring (1) to the assembly sleeve (2).

2011

2 1

Note
The sealing lip must face the crankshaft in assembly.

39510 0

Note
Installation depth X = approx. 2.5 mm of the crankshaft sealing ring.

X
39352 0

Press in crankshaft sealing ring with assembly tool.

Note
- Note installation depth.

33828 1
11/2004

2/4

0312 1579 - 0138

2011
Install rear cover (flywheel side) Clean the sealing surface on the rear cover and crankcase. Apply sealant DEUTZ DW 67 to rear cover.

Crankcase W 03-09-01

34100 1

Mount the rear cover with crankshaft sealing ring and tighten the screws.

Note
- The sealing lip of the crankshaft sealing ring must be touching the crankshaft journal all round. - Do not tighten screws. Align the rear cover to the sealing surface of the oil tray (arrows).

39034 0

Tighten screws in tightening order (1 to 8).

03010

2 8

Install oil tray Job card W 08-04-07. Install connection housing Job card W 03-09-04.

7 3 4 5 1
39037 0

11/2004

3/4

0312 1579 - 0138

Crankcase W 03-09-01
Notes

2011

11/2004

4/4

0312 1579 - 0138

2011
W 03-09-04

Crankcase W 03-09-04

Remove and install connection housing

Tools
- Commercial tools

References
- W 00-05-01 - W 12-06-01

Remove connection housing Mount engine on engine assembly stand Job card W 00-05-01. Remove flywheel Job card W 12-06-01. Unscrew screws (1) and remove engine mounting (2).

39041 0

Unscrew screws (arrows) and remove connection housing.

39046 0
11/2004

1/4

0312 1580 - 0138

Crankcase W 03-09-04
Install connection housing Clean contact surfaces on connection housing and crankcase.

2011

39048 1

Note
Make sure the clamping sleeves (arrows) are in place. Knock clamping sleeves into the crankcase to the stop. Mount the connection housing and center over the clamping sleeves.

39049 0

Tighten screws (arrows) alternately.

03081 03082 13006

39053 0
11/2004

2/4

0312 1580 - 0138

2011
Mount engine bearing (2) and tighten screws (1).
00003

Crankcase W 03-09-04

Note
Note installation position. Install flywheel. Job card W 12-06-01. Disassemble engine from engine assembly stand Job card W 00-05-01

39041 0

11/2004

3/4

0312 1580 - 0138

Crankcase W 03-09-04
Notes

2011

11/2004

4/4

0312 1580 - 0138

2011
W 03-11-01

Crankcase W 03-11-01

Remove and install camshaft bearing, check

Tools
- Commercial tools - Special tools 100 700 - Setting bolt 143 820 - Assembly tool

References
- W 01-02-02 - W 02-04-01 - W 07-04-01(Motorpal) - W 07-04-01(Bosch) - W 07-11-01

Remove camshaft Remove crankshaft Job card W 02-04-01. Remove toggle lever and toggle lever blocks Job card W 01-02-02. Remove injection pumps Job card W 07-04-01 (Motorpal) Job card W 07-04-01 (Bosch) Remove fuel pump Job card W 07-11-01.

39199 0

Unscrew screw (1) and remove startup disc (2). Unscrew setting bolts (3).

3
39302 0
11/2004

1/10

0312 1581 - 0138

Crankcase W 03-11-01
Press in all tappets. Pull out camshaft (1) carefully to the flywheel side.

2011

39303 0

Check the camshaft bearing. Prepare internal measuring device Mount probe bolt for the appropriate measuring range in the internal measuring device. Mount meter with approx. 1 mm pre-tension in the internal measuring device. Set micrometer gauge to 54 mm. Balance the internal measuring device between the test surfaces of the micrometer gauge and set the meter to the reversal point of the pointer to "0".

34768 1

Note
Schematic representation for measuring the camshaft bearing at the points "a" and "b" in the levels "1" and "2".

37239 0
11/2004

2/10

0312 1581 - 0138

2011
Measure camshaft bearing with internal measuring device. Insert internal measuring device in the camshaft bearing. Balance the internal measuring device respectively at the given measuring points and read off the measured value at the reversal point of the pointer.

Crankcase W 03-11-01

Note
- Measuring points, see schematic diagram. - If the wear limit is reached, the bearing has to be changed.
03 13 03 14

39304 0

Remove camshaft bearing Remove all tappets (arrow).

Note
Put down the components in the order of installation, note order of cylinders.

39305 0

Remove outer camshaft bearing Insert extraction bush (1) in outer camshaft bearing.

39306 0
11/2004

3/10

0312 1581 - 0138

Crankcase W 03-11-01
Push in spindle, push on holder (1) and insert in inside camshaft bearing.

2011

Note
Make sure that the holder is evenly in contact with the crankcase. Fit washer and nut.

39307 0

Press out outer camshaft bearing. Dismantle assembly tool and remove camshaft bearing.

39308 0

Remove inner camshaft bearing Insert extraction bush (1) in inner camshaft bearings. Insert spindle and fit washer and nut.

Note
Align counterbearing in the center of the bearing bore (arrow).

39309 0
11/2004

4/10

0312 1581 - 0138

2011
Pull out inner camshaft bearing. Dismantle assembly tool and remove camshaft bearing.

Crankcase W 03-11-01

39310 0

Install camshaft bearing

Note
Schematic for installation direction of the joint in the camshaft bearing.

39311 0

Note
Schematic for the installation depth of the camshaft bearing.
Number of cylinders 2-cylinder 3-cylinder B = opposite side to flywheel 0.5 0.3 mm 117.1 0.3 mm 0.5 0.3 mm 117.1 0.3 mm 0.5 0.3 mm 117.1 0.3 mm 228.1 0.3 mm

A = flywheel side 2.5 0.3 mm 2.5 0.3 mm 118.9 0.3 mm 2.5 0.3 mm 118.9 0.3 mm

4-cylinder

33794 1
11/2004

5/10

0312 1581 - 0138

Crankcase W 03-11-01
Install inner camshaft bearing Mount inner camshaft bearing.

2011

Note
- Note position of joint (1), see schematic diagram. - Check that the oil bores (arrows) in the camshaft bearing and the crankcase match up.

39312 0

Insert extraction bush (1) in the inner camshaft bearing. Insert spindle and fit washer and nut.

Note
- Do not change the installation position of the camshaft bearing. - Counterbearing centered to bearing bore.

39313 0

Pull in camshaft bearing until the extraction socket is almost flush with the crankcase (arrow). Loosen assembly tool. Check that the lube oil bores match up.

Note
If the lube oil bores do not match up, the camshaft bearing must be mounted again.

39314 0
11/2004

6/10

0312 1581 - 0138

2011
Measure the installation depth of the camshaft bearing with the depth measuring appliance from the crankcase joint to the camshaft bearing.

Crankcase W 03-11-01

Note
- Correct the installation depth of the camshaft bearing if necessary. - Installation depth, see schematic diagram. Remove the assembly tool.

39315 0

Install outer camshaft bearing Mount outer camshaft bearing.

6
2 3

Note
- Note position of joint (1), see schematic diagram. - Check that the oil bores (2) in the camshaft bearing and the crankcase match up. - In the camshaft bearing on the flywheel side, the bores (3) for the setting bolts must match up with the camshaft lock.

39316 0

Insert counterbearing (1) in inner camshaft bearing. Insert spindle and fit washer and nut. Insert extraction bus in outer camshaft bearing.

Note
- Do not change the installation position of the camshaft bearing. - Make sure that the counterbearing is evenly in contact with the crankcase.

39307 0
11/2004

7/10

0312 1581 - 0138

Crankcase W 03-11-01
Pull in the camshaft bearing. Loosen assembly tool. Check that the lube oil bores match up.

2011

Note
If the lube oil bores do not match up, the camshaft bearing must be mounted again.

39317 0

Measure the installation depth of the camshaft bearing with the depth measuring appliance from the crankcase joint to the camshaft bearing.

Note
- Correct the installation depth of the camshaft bearing if necessary. - Installation depth, see schematic diagram. Remove the assembly tool.

39318 0

Oil tappets lightly with engine oil and insert (arrow).

Note
Note assignment.

39305 0
11/2004

8/10

0312 1581 - 0138

2011
Install camshaft Oil camshaft bearing and camshaft journal lightly.

Crankcase W 03-11-01

Note
The connecting surface (arrow) with the muff of the measuring mechanism must be clean and oil free.

39252 0

Insert camshaft carefully.

Note
Check that the bores (1) in the camshaft and the crankcase match up.

39319 0

Fit startup disc (1) and tighten screw.

Note
The lubricating groove (2) of the startup disc must face the crankcase.

2
39320 0
11/2004

9/10

0312 1581 - 0138

Crankcase W 03-11-01
Turn in the setting bolt (1), for locking the camshaft, to the stop in the crankcase. Tighten screw.
04002

2011

39321 0

Install crankshaft Job card W 02-04-01. Install toggle lever and toggle lever blocks Job card W 01-02-02. Install fuel pump Job card W 07-11-01. Install injection pumps. Job card W 07-04-01(Motorpal) Job card W 07-04-01(Bosch)

39199 0

11/2004

10/10

0312 1581 - 0138

2011
W 04-04-11

Engine control W 04-04-11

Check engine control times

Tools
- Commercial tools - Special tools 100 700 - Setting bolt
!

References
- W 04-04-12 (old version) - W 04-04-12 (new version)

Caution!
It is not permissible to retighten a toothed belt which has already been in operation and to set the engine control times.

Check engine control times Lock camshaft. Unscrew cap (1) and remove sealing ring.

39670 0

Insert setting bolt (1) in the bore (2) to lock the camshaft.

39671 0
11/2004

1/4

0312 1583 - 0138

Engine control W 04-04-11

Hold the setting bolt lightly and turn the crankshaft in the direction of rotation of the engine (clockwise) until the setting bolt engages the bore of the camshaft.

2011

39672 0

Screw setting bolts (1) into the crankcase.

39186 0

Unscrew cap (1) and remove sealing ring.

39187 0
11/2004

2/4

0312 1583 - 0138

2011
Tighten center screw with the torque wrench in engine direction of rotation with 40 Nm. Carefully relieve pressure on the torque wrench.

Engine control W 04-04-11

Note
Do not turn the crankshaft any more.

34143 1

Turn in the setting bolt (1) to the crankshaft lock until it is lightly touching the crankshaft.

Note
Do not turn the crankshaft when screwing in the setting bolt. Make help marks (arrow) on the crankcase and setting bolt.

39517 0

The engine control times are set correctly when the setting bolt can be turned another 0.75 to 2.25 turns up to the stop in the crankcase.

Note
If the screw-in depth "X" deviates from the specification, the toothed belt and the clamping roller must be changed. Renew toothed belt and clamping roller Job card W 04-04-12(old version) Job card W 04-04-12(new version) Unscrew the setting bolts for camshaft and crankshaft locking.

39543 0
11/2004

3/4

0312 1583 - 0138

Engine control W 04-04-11

Tighten locking screw (1) with new CU sealing ring.
03003

2011

39670 0

Tighten locking screw (1) with new CU sealing ring.

03003

39187 0

11/2004

4/4

0312 1583 - 0138

2011
W 04-04-12

Engine control W 04-04-12

Renew toothed belt and clamping roller (old version of the clamping roller)
Tools
- Commercial tools 8189 - Torx tool kit 9120 - Special bit, 70 mm long 9122 - Special bit, 25 mm long - Special tools 100 700 - Setting bolt 144 130 - Holder
!

References
- W 12-02-01 (FL, BFL engines) - W 12-02-01 (FM, BFM engines) - W 12-08-03

Caution!
The toothed belt and the clamping roller must be renewed after every disassembly regardless of their time in operation.

Note
Distinguishing features of the old version of the clamping roller: - Pointer and notch (1) serve to set and check the toothed belt tension. - The clamping roller is locked by a guide fork (2) on the front cover.

2
39258 0

Renew toothed belt and clamping roller Remove V-belt Job card W 12-02-01 (FL, BFL engines) Job card W 12-02-01 (FM, BFM engines) In FM, BFM engines If available, unscrew screws (1) and remove fan.

39625 0
11/2004

1/16

0312 1584 - 0138

Engine control W 04-04-12

Unscrew screws (1), flange hub (2) and remove V-belt pulley.

2011

2 1
39461 0

Unscrew screws (1) and remove V-belt pulley (2).

Note
Hold at the center screw.

1
39354 0

Remove centrifugal disc (1). Remove toothed belt and clamping roller of the hydraulic pump Job card W 12-08-03.

39355 0
11/2004

2/16

0312 1584 - 0138

2011
In FL, BFL engines Unscrew screws (1) and remove V-belt clamping roller (2).

Engine control W 04-04-12

39356 0

Unscrew locking screw (1).

Note
Use a special bit, 70 mm long. Unscrew screws (2) and remove protective cover (1).

1 3

39357 0

Unscrew screws (1) and remove protective cover (2).

1
39358 0
11/2004

3/16

0312 1584 - 0138

Engine control W 04-04-12

Lock camshaft Unscrew cap (1) and remove sealing ring.

2011

39670 0

Insert setting bolt (1) in the bore (2) to lock the camshaft.

39671 0

Hold the setting bolt lightly and turn the crankshaft in the direction of rotation of the engine (clockwise) until the setting bolt engages the bore of the camshaft.

39672 0
11/2004

4/16

0312 1584 - 0138

2011
Screw setting bolt (1) into the crankcase to the stop.

Engine control W 04-04-12

39186 0

Lock the crankshaft Unscrew cap (1) and remove sealing ring.

39187 0

Insert setting bolt (1) in the bore (2) to lock the crankshaft.

1
39516 0
11/2004

5/16

0312 1584 - 0138

Engine control W 04-04-12

Screw setting bolts (1) into the crankcase.

2011

Note
The cylinder at the front cover is now in the ignition UT.

39188 0

Unscrew screw (1) and remove clamping roller (2). Remove toothed belt (3).

1 2
34054 1

Loosen camshaft toothed belt wheel Mount holder (1) and loosen center screw (2).

Note
Do not turn the camshaft.

39359 0
11/2004

6/16

0312 1584 - 0138

2011
Install toothed belt and clamping roller Tighten the center screw (1) hand tight.

Engine control W 04-04-12

Note
- To guarantee the length compensation of the toothed belt, the camshaft toothed belt wheel must still be turnable. - Use new center screw.

39360 0

Turn the crankshaft carefully in the direction of rotation of the engine (clockwise) until it touches the setting bolts.

39130 0

Mount new toothed belt.

Note
Note the running direction of the toothed belt, the arrows (1) must point in the direction of rotation of the engine (arrow).

39361 0
11/2004

7/16

0312 1584 - 0138

Engine control W 04-04-12

Insert new clamping roller with the guide fork (1) of the base plate in the guide pin (2) of the front cover.

2011

Note
When installing a hydraulic pump, watch out for different clamping rollers. Width of clamping roller for: - Camshaft drive 30 mm - Hydraulic pump drive 35 mm Screw in screw (3).

39362 0

Position setting eccenter (arrow) in 6:00 h position. Press the clamping roller against the toothed belt and pre-tighten the screw (1).
04052

39363 0

Align the toothed belt so that there is an even distance between the cover and toothed belt of 8 to 9 mm.

34132 1
11/2004

8/16

0312 1584 - 0138

2011
Tighten the draw side (1) of the toothed belt by turning the camshaft toothed belt wheel in the direction of the arrow (counterclockwise).

Engine control W 04-04-12

Note
- Turn the camshaft toothed wheel by hand, not by the center screw. - The crankshaft must be held against the stop whilst setting the toothed belt.

39364 0

Remove locking pin (1).

34133 1

Turn the setting eccenter in the direction of the arrow (counterclockwise) until the pointer of the clamping roller is in line with the notch (1).

Note
Turn the setting eccenter at the hexagon socket. Tighten screw.
04052

34134 1
11/2004

9/16

0312 1584 - 0138

Engine control W 04-04-12

Fix the camshaft toothed belt wheel Mount holder (1) and pre-tighten center screw (2). Tighten center screw (2).
04001

2011

Note
- Hold the toothed belt wheel. - Hold the crankshaft against the stop.

34135 1

Check the toothed belt tension Unscrew the setting bolts for camshaft and crankshaft locking. Make help marks on the camshaft toothed belt wheel and the screw opposite (arrow).

34138 1

Turn the crankshaft 2 turns in the direction of rotation of the engine (clockwise) until the help marks (1) are in line.

34139 1
11/2004

10/16

0312 1584 - 0138

2011
Note
- The pointer of the clamping roller must be in line with the notch (1). - If the marks are not in line, the toothed belt tension must be corrected.

Engine control W 04-04-12

34140 1

Correct the toothed belt tension Loosen screw and re-tighten.

04052

Turn the setting eccenter in the direction of the arrow (counterclockwise) until the pointer of the clamping roller is in line with the notch (1). Tighten screw.
04052

34134 1

Check engine control times Lock camshaft. Insert setting bolt (1) for the camshaft lock in the bore and hold lightly. Turn the crankshaft in the direction of rotation of the engine (clockwise) until the setting bolt engages the bore of the camshaft. Turn the setting bolt into the crankcase to the stop.

39186 0
11/2004

11/16

0312 1584 - 0138

Engine control W 04-04-12

Tighten center screw with the torque wrench in engine direction of rotation with 40 Nm. Carefully relieve pressure on the torque wrench.

2011

Note
Do not turn the crankshaft any more.

34143 1

Turn in the setting bolt (1) for the crankshaft lock until it is lightly touching the crankshaft.

Note
Do not turn the crankshaft when screwing in the setting bolt. Make help marks (arrow) on the crankcase and setting bolt.

39517 0

The engine control times are set correctly when the setting bolt can be turned another 0.75 to 2.25 turns up to the stop in the crankcase.

Note
If the screw-in depth "X" deviates from the specification, the toothed belt and the clamping roller must be changed. Unscrew the setting bolts for camshaft and crankshaft locking.

39543 0
11/2004

12/16

0312 1584 - 0138

2011
Tighten locking screw (1) with new CU sealing ring.
03003

Engine control W 04-04-12

39670 0

Tighten locking screw (1) with new CU sealing ring.

03003

39187 0

Inspect the protective covers visually, renew the sealing profile if necessary.

34229 1
11/2004

13/16

0312 1584 - 0138

Engine control W 04-04-12

Mount protective cover (2) and tighten screws (1).

2011

Note
Pay attention to the correct fitting of the protective cover.

2
04053

1
39358 0

Mount protective cover (3) and tighten screws (2) . Screw in locking screw (1).

Note
Use a special bit, 70 mm long. Tighten screws.
04053

1 3

39357 0

Install toothed belt and clamping roller of the hydraulic pump Job card W 12-08-03. Mount centrifugal disc (1).

Note
The hollow throat must face the adapter.

1
39598 0
11/2004

14/16

0312 1584 - 0138

2011
Fit V-belt pulley (1) and tighten screws (2) alternately.

Engine control W 04-04-12

Note
Hold at the center screw.

1 2

12031

39599 0

In FM, BFM engines If available, mount V-belt pulley and flange hub (1). Tighten (2) screws alternately.

2
12031

2
39462 0

Mount fan and disc, tighten screws (1).

09042

39624 0
11/2004

15/16

0312 1584 - 0138

Engine control W 04-04-12

In FL, BFL engines Fit V-belt clamping roller (2) and tighten screws (1). Install V-belt Job card W 12-02-01 (FL, BFL engines) Job card W 12-02-01 (FM, BFM engines).

2011

39356 0

11/2004

16/16

0312 1584 - 0138

2011
W 04-04-12

Engine control W 04-04-12

Renew toothed belt and clamping roller (new version of the clamping roller)
Tools
- Commercial tools 8189 - Torx tool kit 9120 - Special bit, 70 mm long 9122 - Special bit, 25 mm long - Special tools 100 700 - Setting bolt 144 130 - Holder
!

References
- W 12-02-01 (FL, BFL engines) - W 12-02-01 (FM, BFM engines) - W 12-08-03

Caution!
The toothed belt and the clamping roller must be renewed after every disassembly regardless of their time in operation.

Note
Distinguishing features of the new version of the clamping roller: - The bores (arrows) serve for setting and inspecting the toothed belt tension. - The clamping roller has no lock on the front cover.

39600 0

Renew toothed belt and clamping roller Remove V-belt Job card W 12-02-01 (FL, BFL engines) Job card W 12-02-01 (FM, BFM engines) In FM, BFM engines If available, unscrew screws (1) and remove fan.

39625 0
11/2004

1/16

0312 1585 - 0138

Engine control W 04-04-12

Unscrew screws (1) and remove flange hub (2) and V-belt pulley.

2011

2 1
39461 0

Unscrew screws (1) and remove V-belt pulley (2).

Note
Hold at the center screw.

1
39354 0

Remove centrifugal disc (1). Remove toothed belt and clamping roller of the hydraulic pump Job card W 12-08-03.

39355 0
11/2004

2/16

0312 1585 - 0138

2011
In FL, BFL engines Unscrew screws (1) and remove V-belt clamping roller (2).

Engine control W 04-04-12

39356 0

Unscrew locking screw (1).

Note
Use a special bit, 70 mm long. Unscrew screws (2) and remove protective cover (1).

1 3

39357 0

Unscrew screws (1) and remove protective cover (2).

1
39358 0
11/2004

3/16

0312 1585 - 0138

Engine control W 04-04-12

Lock camshaft Unscrew cap (1) and remove sealing ring.

2011

39670 0

Insert setting bolt (1) in the bore (2) to lock the camshaft.

39671 0

Hold the setting bolt lightly and turn the crankshaft in the direction of rotation of the engine (clockwise) until the setting bolt engages the bore of the camshaft.

39672 0
11/2004

4/16

0312 1585 - 0138

2011
Screw setting bolts (1) into the crankcase to the stop.

Engine control W 04-04-12

39186 0

Lock the crankshaft Unscrew cap (1) and remove sealing ring.

39187 0

Insert setting bolt (1) in the bore (2) to lock the crankshaft.

1
39516 0
11/2004

5/16

0312 1585 - 0138

Engine control W 04-04-12

Screw setting bolts (1) into the crankcase.

2011

Note
The cylinder at the front cover is now in the ignition UT.

39188 0

Unscrew screw (1) and remove clamping roller (2). Remove toothed belt (3).

2
39602 0

Loosen camshaft toothed belt wheel (without torsional vibration damper) Mount holder (1) and loosen center screw (2).

Note
Do not turn the camshaft.

39359 0
11/2004

6/16

0312 1585 - 0138

2011
Loosen camshaft toothed belt wheel (with torsional vibration damper)

Engine control W 04-04-12

Note
For camshaft toothed belt wheels with torsional vibration dampers, the hexagon is no longer on the toothed belt wheel (1) but directly on the camshaft toothed belt wheel (2).

39513 0

Hold camshaft toothed belt wheel and loosen the center screw (1).

6
1

Note
Do not turn the camshaft.

39673 0

Install toothed belt and clamping roller Tighten the center screw (1) hand tight.

Note
- To guarantee the length compensation of the toothed belt, the camshaft toothed belt wheel must still be turnable. - Use new center screw.

39360 0
11/2004

7/16

0312 1585 - 0138

Engine control W 04-04-12

Turn the crankshaft carefully in the direction of rotation of the engine (clockwise) until it touches the setting bolts.

2011

39130 0

Mount new toothed belt.

Note
Note the running direction of the toothed belt, the arrows (1) must point in the direction of rotation of the engine (arrow).

39361 0

Mount new clamping roller (1) and position setting eccenter (arrow) at 6.00 h position.

Note
When installing a hydraulic pump, watch out for different clamping rollers. Width of clamping roller for: - Camshaft drive 30 mm - Hydraulic pump drive 35 mm Screw in screw (2).

39603 0
11/2004

8/16

0312 1585 - 0138

2011
Press the clamping roller against the toothed belt and pre-tighten the screw.
04052

Engine control W 04-04-12

39604 0

Align the toothed belt so that there is an even distance between the cover and the toothed belt of 8 to 9 mm.

34132 1

Tighten the draw side (1) of the toothed belt by turning the camshaft toothed belt wheel in the direction of the arrow (clockwise).

Note
- Turn the camshaft toothed wheel by hand, not by the center screw. - The crankshaft must be held against the stop whilst setting the toothed belt.

39364 0
11/2004

9/16

0312 1585 - 0138

Engine control W 04-04-12

Turn setting eccenter in direction of arrow (counterclockwise) until the bores (1) in the setting eccenter are in line.

2011

Note
Turn the setting eccenter at the hexagon socket. Tighten screw (2).
04052

39605 0

Fix the camshaft toothed belt wheel (without torsional vibration damper) Mount holder (1) and pre-tighten center screw (2). Tighten center screw (2).

2 1

Note
- Hold the toothed belt wheel. - Hold the crankshaft against the stop.
04001

39606 0

Fix the camshaft toothed belt wheel (with torsional vibration damper) Pre-tighten (1) and tighten center screw.

Note
- Hold the camshaft toothed belt wheel - Hold the crankshaft against the stop.
04001

39674 0
11/2004

10/16

0312 1585 - 0138

2011
Check the toothed belt tension Unscrew the setting bolts for camshaft and crankshaft locking. Make help marks on the camshaft toothed belt wheel and insert the screw opposite (1). Turn the crankshaft 2 turns in the direction of rotation of the engine (clockwise) until the help marks are in line.

Engine control W 04-04-12

39607 0

Note
- The bores (1) in the setting eccenter must be in line. - If the marks are not in line, the toothed belt tension must be corrected.

39608 0

Correct the toothed belt tension Loosen screw (2) and re-tighten.
04052

Turn setting eccenter in direction of arrow (counterclockwise) until the bores (1) in the setting eccenter are in line. Tighten screw (2).

2
04052

39605 0
11/2004

11/16

0312 1585 - 0138

Engine control W 04-04-12

Check engine control times Lock camshaft Insert setting bolt (1) for the camshaft lock in the bore and hold lightly. Turn the crankshaft in the direction of rotation of the engine (clockwise) until the setting bolt engages the bore of the camshaft. Screw setting bolt into the crankcase to the stop.

2011

39186 0

Tighten center screw with the torque wrench in engine direction of rotation with 40 Nm. Carefully relieve pressure on the torque wrench.

Note
Do not turn the crankshaft any more.

39609 0

Turn in the setting bolt (1) to the crankshaft lock until it is lightly touching the crankshaft.

Note
Do not turn the crankshaft when screwing in the setting bolt. Make help marks (arrow) on the crankcase and setting bolt.

39517 0
11/2004

12/16

0312 1585 - 0138

2011
The engine control times are set correctly when the setting bolt can be turned another 0.75 to 2.25 turns up to the stop in the crankcase.

Engine control W 04-04-12

Note
If the screw-in depth (X) deviates from the specification, the toothed belt and the clamping roller must be changed. Unscrew the setting bolts for camshaft and crankshaft locking.

39543 0

Tighten locking screw (1) with new CU sealing ring.

03003

39670 0

Tighten locking screw (1) with new CU sealing ring.

03003

39187 0
11/2004

13/16

0312 1585 - 0138

Engine control W 04-04-12

Inspect the protective covers visually, renew the sealing profile if necessary.

2011

34229 1

Mount protective cover (2) and tighten screws (1).

Note
Pay attention to the correct fitting of the protective cover.

2
04053

1
39358 0

Mount protective cover (3) and tighten screws (2). Screw in locking screw (1).

Note
Use a special bit, 70 mm long. Tighten screws.
04053

1 3

39357 0
11/2004

14/16

0312 1585 - 0138

2011
Install toothed belt and clamping roller of the hydraulic pump Job card W 12-08-03. Mount centrifugal disc (1).

Engine control W 04-04-12

Note
The hollow throat must face the adapter.

1
39598 0

Fit V-belt pulley (1) and tighten screws (2) alternately.

6
1 2

Note
Hold at the center screw.

12031

39599 0

In FM, BFM engines (as an overview) If available, mount the V-belt pulley and flange hub (1). Tighten (2) screws alternately.

2
12031

2
39462 0
11/2004

15/16

0312 1585 - 0138

Engine control W 04-04-12

Mount fan and disc, tighten screws (1).
12031

2011

39624 0

In FL, BFL engines Fit V-belt clamping roller (2) and tighten screws (1). Install V-belt Job card W 12-02-01 (FL, BFL engines) Job card W 12-02-01 (FM, BFM engines)

39356 0

11/2004

16/16

0312 1585 - 0138

2011
W 04-05-05

Engine control W 04-05-05

Remove and install camshaft

Tools
- Commercial tools - Special tools - 100 700 - Setting bolt

References
- W 01-02-02 - W 03-09-01 - W 04-04-12 (old version) - W 04-04-12 (new version) - W 07-04-01 (Motorpal) - W 07-04-01 (Bosch) - W 07-11-01

Remove camshaft Remove toothed belt and clamping roller and loosen camshaft toothed belt wheel Job card W 04-04-12 (old version) Job card W 04-04-12 (new version)

2 1

Unscrew center screw (1) with washer (2) and remove the camshaft toothed belt wheel (3).

Note
There is no washer (2) on the camshaft toothed belt wheel with torsional vibration damper.

39243 0

Remove toggle lever and toggle lever blocks Job card W 01-02-02. Remove injection pumps Job card W 07-04-01 (Motorpal) Job card W 07-04-01 (Bosch) Remove fuel pump Job card W 07-11-01. Remove rear cover (flywheel side) Job card W 03-09-01.

39245 0
11/2004

1/6

0312 1586 - 0138

Engine control W 04-05-05

Unscrew screw (1) and remove startup disc (2). Unscrew setting bolts (3).

2011

39246 0

Press in all tappets. Pull out camshaft (1) carefully to the flywheel side.

39242 0

Remove tappets. Remove all tappets (arrow).

Note
Put down the components in the order of installation, note order of cylinders. Check the tappets for visible signs of wear.

39247 0
11/2004

2/6

0312 1586 - 0138

2011
Install tappets Oil all tappets (arrow) lightly with engine oil and insert.

Engine control W 04-05-05

Note
Note assignment.

39247 0

Install camshaft Oil camshaft bearing and camshaft journal lightly with engine oil.

Note
The connecting surface (arrow) with the muff of the measuring mechanism must be clean and oil free.

39252 0

Insert camshaft carefully.

Note
- The muff of the measuring mechanism must engage the front camshaft journal. - Check that the bores (1) in the camshaft and the crankcase match up.

39253 0
11/2004

3/6

0312 1586 - 0138

Engine control W 04-05-05

Fit startup disc (1) and tighten screw.

2011

Note
The lubricating groove (2) of the startup disc must face the crankcase.

1 2

39254 0

Screw setting bolts (1) into the crankcase to the stop. Tighten screw.
04002

39255 0

Mount camshaft toothed belt wheel (3) and tighten new center screw (1) with washer (2).

Note
- There is no washer (2) on the camshaft toothed belt wheel with torsional vibration damper. - All connections must be clean and oil free. Install toothed belt and clamping roller, fix camshaft toothed belt wheel Job card W 04-04-12 (old version) Job card W 04-04-12 (new version)

2 1

39243 0
11/2004

4/6

0312 1586 - 0138

2011
Install toggle lever and toggle lever blocks Job card W 01-02-02. Install injection pumps. Job card W 07-04-01 (Motorpal) Job card W 07-04-01 (Bosch) Install fuel pump Job card W 07-11-01. Install rear cover (flywheel side) Job card W 03-09-01.

Engine control W 04-05-05

39256 0

11/2004

5/6

0312 1586 - 0138

Engine control W 04-05-05

Notes

2011

11/2004

6/6

0312 1586 - 0138

2011
W 04-05-06

Engine control W 04-05-06

Check camshaft
Tools
- Commercial tools

References
- W 04-05-05

Check camshaft Remove camshaft Job card W 04-05-05. Visually inspect cam and bearing pin for wear, renew camshaft if necessary. Install camshaft Job card W 04-05-05.

39058 0

11/2004

1/2

0312 1587 - 0138

Engine control W 04-05-06

Notes

2011

11/2004

2/2

0312 1587 - 0138

2011
W 05-07-01

Speed governing W 05-07-01

Remove and install speed governor

Tools
- Commercial tools

Remove speed governor Pull cable plug (1) out of speed governor (2). Unscrew screw (3) and remove speed governor.

1 3

36789 1

Install speed governor Fit new round sealing ring (arrow) onto speed governor.

36790 1
11/2004

1/2

0312 1588 - 0138

Speed governing W 05-07-01

Insert speed governor (2) and tighten screw (3).
05011

2011

Plug cable plug (1) to speed governor.

1 3

36789 1

11/2004

2/2

0312 1588 - 0138

2011
W 06-01-05

Exhaust system / Charging W 06-01-05

Remove and install exhaust manifold

Tools
- Commercial tools 8189 - Torx tool kit

References
- W 06-06-04

Auxiliary material
- DEUTZ S1

In BF engines Remove turbocharger (1). Job card W 06-06-04.

39071 0

Remove exhaust manifold Unscrew screws (arrows), remove exhaust manifold (1) and gaskets. Check components for visible signs of damage.

39222 0
11/2004

1/2

0312 1589 - 0138

Exhaust system / Charging W 06-01-05

Install exhaust manifold Clean the sealing surface on the exhaust manifold and cylinder head.

2011

Note
Note installation position of the gaskets (1).

1
39223 0

Mount exhaust manifold with new gaskets and tighten screws.

Note
Coat screws with assembly aid DEUTZ S1. Tighten screws alternately from the center outwards.
06001

39224 0

In BF engines Install turbocharger (1). Job card W 06-06-04.

39071 0
11/2004

2/2

0312 1589 - 0138

2011
W 06-06-04

Exhaust system / Charging W 06-06-04

Remove and install turbocharger

Tools
- Commercial tools 9090 - Clamping pliers

Note
Collect drained operating materials in suitable vessels and dispose of according to regulations.

Auxiliary material
- DEUTZ S1

Remove turbocharger If available, remove the bleed pipe (1) and reducer (2). Unscrew screws (3). Loosen pipe clip (4), remove reducer with bleed pipe.

3 1 3

4
39394 0

Unscrew screw (1) and remove holder.

39395 0
11/2004

1/6

0312 1590 - 0138

Exhaust system / Charging W 06-06-04

Pull oil return line (1) out of the crankcase and pull off from oil return pipe flange support (2).

2011

2 1

39396 0

Unscrew hollow screws (1), remove oil pressure line (2) and sealing rings.

1
39397 0

Unscrew screws (1), remove oil return pipe flange support (2) and gasket.

39398 0
11/2004

2/6

0312 1590 - 0138

2011
Loosen pipe clip (1) with clamping pliers.

Exhaust system / Charging W 06-06-04

39376 0

Unscrew nuts (1), remove turbocharger (2) and gasket. Check components for visible signs of damage.

6
1

39377 0

Install turbocharger Clean the sealing surface of the turbocharger and exhaust manifold. Mount turbocharger (2) with new gasket and tighten nuts (1).

Note
Coat pin bolts with assembly aid DEUTZ S1.
06020

39377 0
11/2004

3/6

0312 1590 - 0138

Exhaust system / Charging W 06-06-04

Position pipe clip (1) with clamping pliers.

2011

39376 0

Clean the sealing surface of the turbocharger and oil return pipe flange support. Mount oil return pipe flange support (1) with new gasket and tighten screws (2).
08044

39627 0

Pull new round sealing ring (arrow) onto oil return pipe flange support.

39399 0
11/2004

4/6

0312 1590 - 0138

2011
Mount oil pressure line (2), tighten hollow screws (1) with new CU sealing rings.

Exhaust system / Charging W 06-06-04

2
08042

1
39397 0

Fit new round sealing ring (arrow) onto oil return pipe.

39378 0

Push oil return pipe (1) onto oil return pipe flange support (2) and insert in crankcase.

Note
Oil round sealing rings lightly.

2 1

39396 0
11/2004

5/6

0312 1590 - 0138

Exhaust system / Charging W 06-06-04

Mount holder and tighten screw (1).
08044

2011

39395 0

Clean sealing surface on bleed pipe and cylinder head. If available, install the bleed pipe (1) and reducer (2). Mount reducer with bleed pipe and new gasket, tighten screws (3).
03060

3 1 3

Fix pipe clip (1).

2
03060

4
39394 0

11/2004

6/6

0312 1590 - 0138

2011
W 06-07-03

Exhaust system / Charging W 06-07-03

Remove and install air intake pipe

Tools
- Commercial tools 8189 - Torx tool kit

References
- W 06-01-05

Remove air intake pipe Remove exhaust manifold Job card W 06-01-05. Unscrew screws (arrows), remove air intake pipe and gaskets.

39059 0

Install air intake pipe Clean sealing surfaces on air intake pipe and cylinder head.

Note
Note installation position of the gaskets (1).

39064 0
11/2004

1/2

0312 1591 - 0138

Exhaust system / Charging W 06-07-03

Mount air intake pipe with new gaskets and tighten screws. Tighten screws from the center outwards.
06030

2011

Install exhaust manifold Job card W 06-01-05.

39066 0

11/2004

2/2

0312 1591 - 0138

2011
W 07-02-06

Crankcase W 07-02-06

Remove and install control linkage and guide bushes

Tools
- Commercial tools - Special tools 110 140 - Assembly tool 150 140 - Extraction tool 150 150 - Assembly pin

References
- W 03-08-01 - W 03-09-04 - W 07-04-01 (Motorpal) - W 07-04-01 (Bosch) - W 07-08-02 - W 08-11-12 - W 09-11-01 - W 13-02-03

Auxiliary material
- DEUTZ DW 72

Remove control linkage Remove front cover Job card W 03-08-01. Remove injection pumps Job card W 07-04-01 (Motorpal) Job card W 07-04-01 (Bosch) Remove connection housing Job card W 03-09-04.

39069 0

In FL, BFL engines Remove cooling blower Job card W 09-11-01. In FM, BFM engines Remove generator Job card W 13-02-03. In BFL, BFM engines Remove charging pressure dependent full load stop Job card W 07-08-02.

39069 0
11/2004

1/12

0312 1592 - 0138

Crankcase W 07-02-06
Knock out cylindrical pin (1).

2011

39072 0

Remove control linkage (1) with spring.

39073 0

Remove guide bush (opposite side to flywheel) Insert assembly pin (1) in guide bush (2).

39074 0
11/2004

2/12

0312 1592 - 0138

2011
Knock out guide bush.

Crankcase W 07-02-06

39075 0

Install guide bush (opposite side to flywheel) Unscrew locking screw (1).

39076 0

Push spacer bush (1) onto assembly pin (2). Insert assembly pin in the centering (3).

Note
The guide pin (arrow) must engage in the groove (4).

2 1

39077 0
11/2004

3/12

0312 1592 - 0138

Crankcase W 07-02-06
Push guide bush (1) onto assembly pin.

2011

Note
The chamfer (arrow) must face the crankcase in assembly.

39078 0

Mount centering on crankcase.

Note
- The crankcase contact surface must be clean. - The fixing bolt (1) must engage the bore (2).

2 1

39079 0

Tighten screw (1). Knock in the guide sleeve until the assembly pin touches the spacer bush (arrow).

1
Remove centering with assembly pin.

39082 0
11/2004

4/12

0312 1592 - 0138

2011
Tighten new locking screw.

Crankcase W 07-02-06

Note
The threaded bore for the locking screw must be free from oil, corrosion and dirt and be dry.
03007

39084 0

Remove oil rise pipe Unscrew locking screw (1). Remove oil thermostat Job card W 08-11-12.

39087 0

Remove cap (1).

39088 0
11/2004

5/12

0312 1592 - 0138

Crankcase W 07-02-06
Drill oil rise pipe (1) with a 5.5 mm drill on one side.

2011

Note
- Coat the drill with grease so that no drill chips fall into the crankcase. - Remove all drill chips.

39089 0

Insert extraction tool (1) in the oil rise pipe until the bolt (2) snaps into the bore (arrow).

39093 0

Mount spacer bush (1) and disc, tighten nut.

39095 0
11/2004

6/12

0312 1592 - 0138

2011
Pull the oil rise pipe out of the lower press fit (arrow).

Crankcase W 07-02-06

Note
Do not pull out the oil rise pipe completely.

39097 0

Press in bolt (arrow) and remove oil rise pipe.

39098 0

Remove guide bush (flywheel side) Insert assembly pin (1) in guide bush (2).

2 1

39099 0
11/2004

7/12

0312 1592 - 0138

Crankcase W 07-02-06
Knock out guide bush.

2011

39204 0

Install guide bush (flywheel side) Insert assembly pin (1) in centering (2).

Note
The guide pin (arrow) must engage in the groove (3).

2 1

3
39205 0

Push guide bush (1) onto assembly pin.

Note
The chamfer (arrow) must face the crankcase in assembly.

39226 0
11/2004

8/12

0312 1592 - 0138

2011
Insert assembly pin with guide bush.

Crankcase W 07-02-06

Note
The crankcase contact surface must be clean.

39227 0

Mount centering on crankcase and tighten screw (1). Knock in the guide sleeve until the assembly pin touches the centering (arrow). Remove centering with assembly pin.

6
1

39228 0

Install oil rise pipe Insert new oil rise pipe (1).

Note
The chamfer (arrow) must face the crankcase in assembly.

39231 0
11/2004

9/12

0312 1592 - 0138

Crankcase W 07-02-06
Knock in the oil rise pipe until the assembly pin (1) touches the crankcase (arrow).

2011

39232 0

Coat new cap with DEUTZ DW 72 locking agent.

33816 1

Knock in cap flush with crankcase. Install oil thermostat Job card W 08-11-12.

39233 0
11/2004

10/12

0312 1592 - 0138

2011
Tighten new locking screw.

Crankcase W 07-02-06

Note
The threaded bore for the locking screw must be free from oil, corrosion and dirt and be dry.
03007

39235 0

Install control linkage Insert control linkage with spring in the guide bushes.

Note
- Note installation position, the latch (1) must face the oil filling nozzle (2). - Pay attention to easy action of the control linkage.

39236 0

Press together spring and insert cylindrical pin (1) in the bore (2).

Note
- The cylindrical pin must engage in the recess (arrow) for the control path limit. - Make sure that the spring touches the cylindrical pin (3).

3 1

39237 0
11/2004

11/12

0312 1592 - 0138

Crankcase W 07-02-06
Drive in the cylindrical pin flush with the crankcase. Install connection housing Job card W 03-09-04. Install front cover Job card W 03-08-01. Install injection pumps. Job card W 07-04-01 (Motorpal) Job card W 07-04-01 (Bosch) In BFL, BFM engines Install charging pressure dependent full load stop Job card W 07-08-02.

2011

39238 0

In FM, BFM engines Install generator Job card W 13-02-03. In FL, BFL engines Install cooling blower Job card W 09-11-01.

11/2004

12/12

0312 1592 - 0138

2011
W 07-02-07

Fuel system W 07-02-07

Remove and install lifting magnet for start volume release

Tools
- Commercial tools 8027 - Pliers insert

Remove lifting magnet for start volume release Pull cable plug (1) out of lifting magnet (2).

2 1

39662 0

Unscrew lifting magnet (1) with pliers insert and remove sealing ring.

Note
Note clamping direction of the pliers insert. Check components for visible signs of damage.

39663 0
11/2004

1/2

0312 1593 - 0138

Fuel system W 07-02-07

Install lifting magnet for start volume release Mount lifting magnet (1) with new CU sealing ring and tighten with pliers insert.

2011

1
05065

39664 0

Pull cable plug (1) out of lifting magnet (2).

2 1

39662 0

11/2004

2/2

0312 1593 - 0138

2011
W 07-03-01

Fuel system W 07-03-01

Renew injection lines

Tools
- Commercial tools 8018 - Claw wrench 8189 - Torx tool kit

Note
- Cleanliness is extremely important when working on the injection equipment. - Bending the injection lines is not permissible. Small tears may occur which lead to a reduction in the fatigue strength. - Collect drained operating materials in suitable vessels and dispose of according to regulations.

References
- W 08-08-02

Caution!
!

Observe the safety regulations and and national specifications for handling fuels.

Remove injection lines In FL, BFL engines Remove oil cooler Job card W 08-08-02. Unscrew screw (1).

1
39481 0

Unscrew screws (1) and remove air feed (2).

39468 0
11/2004

1/4

0312 1594 - 0138

Fuel system W 07-03-01

Unscrew union nuts (1) from injection valve and injection pump with claw wrench. Remove injection line.

2011

Note
- Put down the components in the order of installation, note order of cylinders. - Seal openings on the injection valve and the injection pump.

39482 0

Install injection lines Mount injection line on injection pump and injection valves and tighten union nuts (1).

Note
Mount the injection lines without tension. Tighten the union nuts of the injection line on the injection pump and injection valve.
07003

39482 0

In FL, BFL engines Mount air feed (2) and tighten screws (1).

39468 0
11/2004

2/4

0312 1594 - 0138

2011
Tighten screw (1).

Fuel system W 07-03-01

1
39481 1

Pre-tighten screw (1) on cylinder head.

09098

Tighten screws (arrows).

09089

Tighten screw (1) on cylinder head.

09098

Install oil cooler Job card W 08-08-02.

34215 1

11/2004

3/4

0312 1594 - 0138

Fuel system W 07-03-01

Notes

2011

11/2004

4/4

0312 1594 - 0138

2011
W 07-04-01

Fuel system W 07-04-01

Remove and install injection pumps (Bosch)

Tools
- Commercial tools Depth-measuring appliance - Special tools 100.710 - Setting bolt 100 880 - Marking pin 103 030 - Test template

References
- W 07-03-01 - W 07-06-04 - W 07-10-06

Note
Distinguishing features for the Bosch injection pump: - Short pump housing.

39300 0

Remove injection pump Remove injection lines Job card W 07-03-01. Remove fuel supply line Job card W 07-10-06. Unscrew nuts (1), remove injection pump (arrows) and compensation gaskets.

1 1

Note
- Loosen nuts evenly to avoid jamming the injection pump. - Put down the components in the order of installation, note order of cylinders.

34043 2
11/2004

1/8

0312 1595 - 0138

Fuel system W 07-04-01

Pull out roller tappet (arrow) using a suitable tool, e.g. outside locking pliers.

2011

Note
- Put down the components in the order of installation, note order of cylinders. - Do not damage the roller tappet.

34044 1

Install the injection pump Unscrew cap (arrow) and remove sealing ring.

34173 1

Move control linkage to mid position.

Note
Ignition off / stop magnet free. Turn in setting bolt (1) to stop.

34174 1
11/2004

2/8

0312 1595 - 0138

2011
Turn crankshaft until the cam for the respective injection pump is standing on the cam basic circuit (1).

Fuel system W 07-04-01

39116 0

Oil lightly and insert the roller tappet.

Note
- Note the assignment of the roller tappet. - The guide pin (1) on the roller tappet must engage in the groove (2).

1
39117 0

Determination of the compensation gasket

Note
Schematic representation for determining the depth "A".

34177 1
11/2004

3/8

0312 1595 - 0138

Fuel system W 07-04-01

Determine depth dimension Measure depth dimension "A" from the crankcase rest to the spring head rest of the roller tappet.

2011

Note
The crankcase rest must be clean. Read and note measured value.

34178 1

Read and note installation dimension "X" from the rating plate of the respective injection pump.

Note
The installation dimension "X" serves exclusively to calculate the compensation gasket. Do not measure on the disassembled injection pump.

34179 1

Determine difference between installation dimension "X" and depth dimension "A".

Example: Installation dimension "X" Depth dimension A Difference 60.00 mm 59.35 mm 0.65 mm

11/2004

4/8

0312 1595 - 0138

2011
Select compensation gasket according to table.
07 21

Fuel system W 07-04-01

12

15

18

21

24

27

34180 1

Note
Since the part number and the gasket thickness are not specified on the compensation gasket, the gasket thickness can be checked with the test template.

39526 0

Mount the appropriate compensation gasket.

Note
Note installation position, the recess (arrow) must face the flywheel.

39119 0
11/2004

5/8

0312 1595 - 0138

Fuel system W 07-04-01

Pull out locking pin (1).

2011

Note
Remove the gasket (2) together with the locking pin.

1 2

34183 1

Insert the marking pin (1) in the bore of the injection pump and snap into the deflection lever (arrow). Clamp the bracket of the marking pin.

34184 1

Insert the injection pump centrally to the long holes. Press in injection pump to stop and tighten nuts. Tighten nuts.
07012

34185 1
11/2004

6/8

0312 1595 - 0138

2011
Loosen clamping bracket and pull out marking pin (1).

Fuel system W 07-04-01

34186 1

Press in locking pin (1) with gasket to stop.

34187 1

Unscrew setting bolt (arrow).

34188 1
11/2004

7/8

0312 1595 - 0138

Fuel system W 07-04-01

Tighten cap with new CU sealing ring.
03004

2011

Check beginning of pumping if necessary Job card W 07-06-04. Install fuel supply line Job card W 07-10-06. Install injection lines Job card W 07-03-01.

34189 1

11/2004

8/8

0312 1595 - 0138

2011
W 07-04-01

Fuel system W 07-04-01

Remove and install injection pumps (Motorpal)

Tools
- Commercial tools - Special tools 100 710 - Setting bolt 103 030 - Test template 101 100 - Marking pin

References
- W 07-03-01 - W 07-06-03 - W 07-06-04 - W 07-10-06

Note
Distinguishing features for the Motorpal injection pump: - Long injection pump housing. - Overflow line on the injection pump.

39484 0

Remove injection pump Remove injection lines Job card W 07-03-01. Remove fuel lines Job card W 07-10-06. Loosen locking screw (1).

Note
The locking screw must be unscrewed for later locking of the injection pump.

39110 0
11/2004

1/8

0312 1596 - 0138

Fuel system W 07-04-01

Unscrew nuts (1), remove injection pump (2) and compensation gaskets.

2011

Note
- Loosen nuts evenly to avoid jamming the injection pump. - Put down the components in the order of installation, note order of cylinders.

39111 0

Pull out roller tappet (arrow) using a suitable tool, e.g. outside locking pliers.

Note
- Put down the components in the order of installation, note order of cylinders. - Do not damage the roller tappet.

39112 0

Unscrew cap (1) and remove sealing ring.

1
39114 0
11/2004

2/8

0312 1596 - 0138

2011
Move control linkage to mid position.

Fuel system W 07-04-01

Note
Ignition off / stop magnet free. Turn in setting bolt (1) to stop.

1
39115 0

Turn crankshaft until the cam for the respective injection pump is standing on the cam basic circuit (1).

39116 0

Oil lightly and insert the roller tappet.

Note
- Note the assignment of the roller tappet. - The guide pin (1) on the roller tappet must engage in the groove (2).

Note
When replacing the roller tapper, the assignment of the injection pump to the roller tappet must be observed.
07 16 07 17

1
39117 0
11/2004

3/8

0312 1596 - 0138

Fuel system W 07-04-01

Determine the thickness of the shim gasket Job card W 07-06-03. Select compensation gasket according to table.
07 21

2011

12

15

18

21

24

27

34180 1

Note
Since the part number and the gasket thickness are not specified on the compensation gasket, the gasket thickness can be checked with the test template.

39526 0

Mount the appropriate compensation gasket.

Note
Note installation position, the recess (arrow) must face the flywheel.

39119 0
11/2004

4/8

0312 1596 - 0138

2011
Install the injection pump

Fuel system W 07-04-01

Note
When replacing the injection pump the assignment of the injection pump to the roller tappet must be observed.
07 16 07 17

39113 0

Pull out locking pin (1).

6
1 2

Note
Remove the gasket (2) together with the locking pin. Unscrew cap (3) and remove sealing ring.

39120 0

Insert marking pin (1) in the bore (2) of the injection pump.

Note
Do not press in the marking pin completely.

39121 0
11/2004

5/8

0312 1596 - 0138

Fuel system W 07-04-01

Position the center punch point (1) on the regulating sleeve (2) (arrow) so that it is underneath the tip of the marking pin.

2011

Note
The center punch point is visible through the bore for the locking screw.

39122 0

Position the tip of the marking pin (1) in the center punch point. Clamp the clamping bracket (2) of the marking pin.

39123 0

Insert the injection pump centrally to the long holes. Press in injection pump to stop and tighten nuts. Tighten nuts.
07012

39124 0
11/2004

6/8

0312 1596 - 0138

2011
Loosen clamping bracket and pull out marking pin (1).

Fuel system W 07-04-01

39125 0

Press in locking pin (1) with gasket to stop. Tighten cap (2) with new CU sealing ring.
07071

6
1

39126 0

Unscrew setting bolt. Tighten locking screw (1) with new CU sealing ring.
03004

Check beginning of pumping if necessary Job card W 07-06-04. Install fuel lines Job card W 07-10-06. Install injection lines Job card W 07-03-01.

39127 0
11/2004

7/8

0312 1596 - 0138

Fuel system W 07-04-01

Notes

2011

11/2004

8/8

0312 1596 - 0138

2011
W 07-06-03

Fuel system W 07-06-03

Determine the thickness of the shim gasket

Tools
- Commercial tools 8170 - Depth measuring appliance

References
- W 07-04-01 (Motorpal)

Note
- All contact and measuring surfaces must be absolutely clean to rule out measuring errors! - The following work procedure must be performed for every injection pump if necessary.

Remove injection pump and compensation gasket. Removal and installation of roller tappet, visual inspection. Job card W 07-04-01(Motorpal)

39892 1

Mount probe for measuring range 50 to 75 mm on depth measuring screw.

Note
Presetting of the measuring range approx. 52 mm.

39183 0
11/2004

1/4

0312 1638 - 0138

Fuel system W 07-06-03

Place the depth measuring screw on the contact surface of the crankcase and keep it pressed against the stop. Turn the depth measuring screw until the probe is touching the roller tappet.

2011

39184 3

In hydro-roller tappets, the working piston in the roller tappet (1) must be pressed down (approx. 1 mm) to determine the total depth dimension by turning on the depth measuring screw to the stop (arrow).

39128 0

Measure, read and note the depth dimension "A" from the crankcase rest to the plate spring rest of the roller tappet.

Note
- The crankcase rest must be clean. - Example: 60.25 mm

39184 0
11/2004

2/4

0312 1638 - 0138

2011
Read and note installation dimension "X" of the rating plate of the respective injection pump.

Fuel system W 07-06-03

Note
- The installation dimension "X" serves to calculate the compensation gasket. - Do not measure on the disassembled injection pump. - The exact installation dimension "X" is specified on the rating plate of the injection pump. - Example: 6088 Installation dimension "X" = 60.88 mm

X
39118 0

Read and note value of the pre-stroke correction from the company rating plate.

Note
The value of the pre-stroke correction is specified with a minus () or plus sign. - Example: 16

39877 2

Calculate compensation gasket thickness "Ss".

Calculation example: Searching for: - Compensation gasket thickness Ss - Compensation gasket thickness without pre-stroke correction So Given: Measured: Calculation: - installation dimension of the injection pump X - Pre-stroke correction Vk - depth dimension A So = X A = 60.88 mm 60.25 mm = 0.63 mm Ss = So + Vk = 0.63 mm + (- 0.16 mm) = 0.47 mm

Select compensation gasket.

11/2004

3/4

0312 1638 - 0138

Fuel system W 07-06-03

Notes

2011

11/2004

4/4

0312 1638 - 0138

2011
W 07-06-04

Fuel system W 07-06-04

Check start of pumping

Tools
- Commercial tools - Special tools 100 120 - Connecting piece 101 300 - Pointer for degree scales 101 500 - Hand pump 101 510 - Tank 100 910 - Scale dial

References
- W 07-03-01 - W 07-10-06 (Bosch) - W 07-10-06 (Motorpal) - W 11-00-03

Note
- The description refers to the cylinder at the front cover. The respective ignition UT must be determined by the scale dial when testing on other cylinders.

Check start of pumping Remove injection lines Job card W 07-03-01. Remove fuel lines Job card W 07-10-06 (Bosch) Job card W 07-10-06 (Motorpal) Remove lifting magnet (shutdown magnet) Job card W 11-00-03. Lock camshaft Unscrew cap (1) and remove sealing ring.

39185 0

Insert setting bolt (1) in the bore (2) to lock the camshaft.

39671 0
11/2004

1/8

0312 1597 - 0138

Fuel system W 07-06-04

Hold the setting bolt lightly and turn the crankshaft in the direction of rotation of the engine (clockwise) until the setting bolt engages the bore of the camshaft.

2011

39672 0

Screw setting bolt (1) into the crankcase to the stop.

39186 0

Lock the crankshaft Unscrew cap (1) and remove sealing ring.

39187 0
11/2004

2/8

0312 1597 - 0138

2011
Insert setting bolt (1) in the bore (2) to lock the crankshaft.

Fuel system W 07-06-04

1
39516 0

Screw setting bolt (1) into the crankcase to the stop.

Note
The cylinder at the front cover is now in the ignition UT.

39188 0

Loosen screw (1) and mount pointer with stop device (2). Tighten screw.

39189 0
11/2004

3/8

0312 1597 - 0138

Fuel system W 07-06-04

Mount scale dial on V-belt pulley. Set pointer in line with "0".

2011

39190 0

Install overflow pipe (1) on pressure valve holder of the injection pump. Install hose (2) on overflow pipe and supply tank. Install high pressure hand pump (3) to injection pump (4) and supply tank.

Note
Make sure that there is enough fuel in the supply tank.

2 4
39191 0

Screw locking screw (1) into injection pump.

Note
Do not tighten locking screw.

39192 0
11/2004

4/8

0312 1597 - 0138

2011
Unscrew setting bolt for camshaft and crankshaft locking. Turn crankshaft approx. 90 against the engines direction of rotation (arrow).

Fuel system W 07-06-04

39193 0

Bleed the suction chamber of the injection pump. Actuate the high pressure hand pump until fuel emerges at the locking screw (1). Tighten the locking screw.
07071

6
1

39192 0

Actuate the high pressure hand pump constantly.

Note
The fuel must flow evenly out of the overflow pipe. Turn the crankshaft slowly and evenly in the direction of rotation of the engine (arrow) until the fuel flow becomes just a dripping.

Note
As soon as the fuel flow becomes a dripping, the beginning of pumping is reached.

39194 0
11/2004

5/8

0312 1597 - 0138

Fuel system W 07-06-04

Read beginning of pumping from the dial.
07 31

2011

39195 0

Note
- The beginning of pumping of other injection pumps must be checked by this method. - Determine the ignition UT of the respective cylinder with the dial. Observe the ignition distance. Ignition distance: 2 cylinder engine 3 cylinder engine 4 cylinder engine 180 120 180

Remove dial and pointer, tighten screw. Remove high pressure hand pump and overflow pipe. Unscrew cap (1) and remove sealing ring.

39192 0
11/2004

6/8

0312 1597 - 0138

2011
Tighten locking screw (1) with new CU sealing ring.
03003

Fuel system W 07-06-04

39185 0

Tighten locking screw (1) with new CU sealing ring.

03003

Install fuel lines Job card W 07-10-06 (Bosch) Job card W 07-10-06 (Motorpal) Install injection lines Job card W 07-03-01. Install lifting magnet (shutdown magnet) Job card W 11-00-03.

39187 0

11/2004

7/8

0312 1597 - 0138

Fuel system W 07-06-04

Notes

2011

11/2004

8/8

0312 1597 - 0138

2011
W 07-07-01

Fuel system W 07-07-01

Remove and install injection valves (in engines with leak fuel line)
Tools
- Commercial tools 8011 - Clamping pliers - Special tools 110 030 - Extractor 150 800 - Extraction tool

References
- W 07-03-01

Note
- Cleanliness is extremely important when working on the injection equipment. - Collect drained operating materials in suitable vessels and dispose of according to regulations. Remove injection valve Remove injection lines Job card W 07-03-01. In engines with leak fuel line Loosen pipe clips (1) and pull off return pipes (2). Unscrew screws and remove overflow pipe (3).

6
1

34031 1

Unscrew screw (1) and remove clamping claw (2).

39485 0
11/2004

1/6

0312 1598 - 0138

Fuel system W 07-07-01

Pull out injection valve (1) and sealing ring (arrow).

2011

Note
- Put down the components in the order of installation, note order of cylinders. - Pull off gaskets burned tight to the cylinder head with extractor and extraction device.

39486 0

Install injection valve Mount new sealing ring (arrow) on injection valve.

34191 1

Insert injection valve.

Note
The leak fuel connection (arrow) must face the Manifold side.
00 81

34192 1
11/2004

2/6

0312 1598 - 0138

2011
Mount the clamping claw and tighten the screw.

Fuel system W 07-07-01

Note
Note installation position of the clamping claw.

34193 1

Tighten screw.
07001

34194 1

Mount overflow pipe (1), attach hoses and tighten screws.

07062

1
Attach return hose (2) and fix hose clip with clamping pliers. Insert return hose in holder (arrows).

Note
The rubber hoses must always be renewed.

34202 1
11/2004

3/6

0312 1598 - 0138

Fuel system W 07-07-01

Attach return hose (1) and fix hose clip with clamping pliers.

2011

Note
Check return pipe, renew if necessary. Install injection lines Job card W 07-03-01.

34203 1

Install injection valve (leak fuel-less) Mount new sealing ring (1) on injection valve.

39487 0

Insert injection valve (1).

Note
The flattened side (arrow) must face the Operating side.

1
00 81

39301 0
11/2004

4/6

0312 1598 - 0138

2011
Mount the clamping claw and tighten the screw.

Fuel system W 07-07-01

Note
Note installation position of the clamping claw.

39488 0

Press the clamping claw to touch the gate (arrow) on the injection valve (arrow) and tighten screw (1).
07001

Install injection lines Job card W 07-03-01.

39489 0

11/2004

5/6

0312 1598 - 0138

Fuel system W 07-07-01

Notes

2011

11/2004

6/6

0312 1598 - 0138

2011
W 07-07-02

Fuel system W 07-07-02

Check and repair injection valve

Tools
- Commercial tools 8021 - Socket size 15 - Special tools 110 110 - Holder

References
- W 07-07-05 - W 07-07-01

Dismantle injection valve Remove injection valves Job card W 07-07-01. Insert injection valve in holder. Unscrew nozzle clamping nut with long socket.

36271 1

Order of individual disassembly - 1 shim disc - 2 pressure spring - 3 pressure bolt - 4 adapter - 5 Injection nozzle - 6 nozzle lock nut Clean parts in clean diesel fuel and blow dry with air.

6 2 3 4 5

36269 1
11/2004

1/4

0312 1599 - 0138

Fuel system W 07-07-02

Check injection nozzle The nozzle needle (1) must slide back to its seat slowly and jolt-free by its own weight when the nozzle body (2) is held vertically.

2011

Note
- Do not touch the nozzle needle with your fingers. - The nozzle needle and nozzle body are lapped together and may not be switched round or changed individually. - If the nozzle needle slides back with a jolt, clean the injection nozzle in diesel fuel again, renew if necessary. - Also clean the new injection nozzle in clean diesel fuel.

1 2

33904 1

Inspect the seat surfaces of the adapter for wear.

Note
Make sure the centering pins (arrows) are in place.

33905 1

Complete injection valve Insert shim disc.

Note
The opening pressure depends on the strength of the shim disc.

36274 1
11/2004

2/4

0312 1599 - 0138

2011
Insert compression spring.

Fuel system W 07-07-02

33907 1

Insert compression bolt.

Note
The center joint must face the compression spring.

33908 1

Insert adapter with the centering pins in the bores in the nozzle holder.

Note
The countersink must face the compression bolt.

33909 1
11/2004

3/4

0312 1599 - 0138

Fuel system W 07-07-02

Mount the injection nozzle with the centering bores on the centering pins of the adapter.

2011

Note
The nozzle needle may not fall out of the nozzle body.

33910 1

Screw on the nozzle clamping nut.

33911 1

Tighten the nozzle clamping nut.

07002

Remove the injection valve from the holder. Check and set injection valves Job card W 07-07-05 Install injection valves Job card W 07-07-01.

33912 1
11/2004

4/4

0312 1599 - 0138

2011
W 07-07-05

Fuel system W 07-07-05

Check and set injection valves (leak fuel-less)

Tools
- Commercial tools 8008 - Nozzle tester 8021 - Socket size 15 - Special tools 110 110 - Holder
!

Caution!
After about three or four actuations of the hand lever, the spring space above the nozzle needle in the injection valve fills up with diesel fuel/test oil. Then it is no longer possible to actuate the hand lever. The nozzle lock nut must be loosened carefully before every test procedure to release pressure from the spring space.

Note
- Cleanliness is extremely important when working on the injection equipment. - Only use pure test oil according to ISO 4113 or clean diesel fuel to test the injection valves.

References
- W 07-07-01

Check the injection valve. Remove injection valves Job card W 07-07-01. Insert injection valve in holder. Loosen the nozzle clamping nut with the long socket approx. 180 (relieve pressure) and re-tighten.
07002

36271 1

Caution!
!

Risk of injury! The fuel penetrates deep into the flesh through the nozzle jet. Risk of blood poisoning!

Install injection valve in the nozzle tester.

35889 1
11/2004

1/6

0312 1600 - 0138

Fuel system W 07-07-05

Testing the opening pressure Press down the lever of the nozzle tester slowly, with connected pressure gauge. The pressure at which the pointer stands still or suddenly drops is the opening pressure.
07 52

2011

36293 1

Note
- When the hand lever of the nozzle tester has been actuated three or four times, the pressure in the spring space has built back up. - The nozzle clamping nut must be loosened again and re-tightened. - The test must be repeated. - If the measured values of three tests are identical, these can be considered valid.
07002

Remove the injection valve from the nozzle tester.

36293 1

Setting the opening pressure on the injection valve Insert the injection valve in the holder, unscrew the nozzle clamping nut and remove all parts.

36270 1
11/2004

2/6

0312 1600 - 0138

2011
Order of single part assembly 123456Shim disc Compression spring Compression bolt Adapter Injection nozzle Nozzle clamping nut

Fuel system W 07-07-05

6 2 3 4 5

36269 1

Select shim disc, for correcting the opening pressure according to the spare parts list.

Note
A thicker disc gives a higher opening pressure. Assemble injection valve and tighten nozzle clamping nut.
07002

Check the injection valve on the nozzle tester again.

36274 1

Tightness test Blow the injection nozzle and nozzle holder dry with air. Press the hand lever of the tester down slowly until approx. 20 bar below the previously read opening pressure are reached.

36293 1
11/2004

3/6

0312 1600 - 0138

Fuel system W 07-07-05

Note
Injection nozzle is tight if it does not drip within 10 seconds.

2011

36294 1

Note
- If the injection nozzle drips, the injection valve must be dismantled and cleaned, the injection nozzle may have to be changed. - Repairs are not permitted.

36295 1

Buzz and jet test Switch off the testers pressure gauge.

Note
The easy action of the nozzle needle in the nozzle body is checked by the acoustic buzz test. Increasing wear in the needle seat of the injection valves changes their buzz behavior.

36296 1
11/2004

4/6

0312 1600 - 0138

2011
Note
After cleaning, a used injection valve must buzz audibly and atomize the fuel finely when the lever is actuated quickly. The injection nozzle must be changed if it does not buzz after cleaning. The jet profile may deviate considerably from that of a new injection valve.

Fuel system W 07-07-05

36296 1

Caution!
!

The pressure in the spring space must be relieved in any case before installing the injection valves.

Loosen the nozzle clamping nut with the long socket approx. 180 (relieve pressure) and re-tighten.
07002

Install injection valves Job card W 07-07-01.

39486 1

11/2004

5/6

0312 1600 - 0138

Fuel system W 07-07-05

Notes

2011

11/2004

6/6

0312 1600 - 0138

2011
W 07-08-01

Fuel system W 07-08-01

Remove and install solenoid valve (LDA)

Tools
- Commercial tools 8027 - Pliers insert

Remove solenoid valve In BFL engines Unscrew screws (1) and remove air duct cover (2).
2

1 1

39080 0

Pull off cable plug from solenoid valve (1) if available.

39665 0
11/2004

1/4

0312 1601 - 0138

Fuel system W 07-08-01

Unscrew solenoid valve (1) with pliers insert and remove sealing ring.

2011

Note
Note clamping direction of the pliers insert. Check components for visible signs of damage.

1
39666 0

Install solenoid valve Mount solenoid valve (1) with new CU sealing ring and tighten with pliers insert.
06094

39667 0

Plug cable plug to solenoid valve (1) if available.

39665 0
11/2004

2/4

0312 1601 - 0138

2011
In BFL engines Mount air duct cover (1).

Fuel system W 07-08-01

Note
The air duct cover must be under the stand plate and the profile rubber (arrows).

39490 0

Fix air duct cover (2). Tighten screws (1).

09087

1 1

39080 0

11/2004

3/4

0312 1601 - 0138

Fuel system W 07-08-01

Notes

2011

11/2004

4/4

0312 1601 - 0138

2011
W 07-08-02

Fuel system W 07-08-02

Remove and install charge pressure full load stop (LDA)

Tools
- Commercial tools 8011 - Clamping pliers 8027 - Pliers insert - Special tools 170 050 - Special wrench

Note
- Collect drained operating materials in suitable vessels and dispose of according to regulations. - A test stand run is necessary to set the charging pressure-dependent full load stop.

Caution!
!

Observe the safety regulations and national specifications for handling fuels!

Remove charging pressure full load stop In FL, BFL engines Unscrew screws (1) and remove the air duct cover (2).
2

1 1

39080 0

Pull the cable plug out of the solenoid valve (1) if available. Pull out the underpressure line (2).

1 2

39381 0
11/2004

1/6

0312 1602 - 0138

Fuel system W 07-08-02

Loosen the hose clips (1) with clamping pliers.

2011

39382 0

Pull off the fuel pipes (1).

39383 0

Unscrew fuel filter (1) with special wrench. Unscrew screws (2) and remove fuel filter console (3) with LDA.

39384 0
11/2004

2/6

0312 1602 - 0138

2011
Unscrew screws (1), remove cover (2) with diaphragm.

Fuel system W 07-08-02

2 1

39385 0

Remove spring (1).

39386 0

Unscrew solenoid valve (1) with pliers insert and remove sealing ring.

Note
- Note clamping direction of the pliers insert. Check components for visible signs of damage.

39387 0
11/2004

3/6

0312 1602 - 0138

Fuel system W 07-08-02

Install charging pressure dependent full load stop Mount solenoid valve (1) with new CU sealing ring and tighten with pliers insert.
06094

2011
1

39388 0

Mount spring (1), diaphragms (2) and cover (3).

Note
Note the installation position of the cover, the underpressure connection must face upwards. Tighten screws.
07096

39389 0

Clean the sealing surface on the fuel filter console and crankcase. Renew the gasket (arrow).

39390 0
11/2004

4/6

0312 1602 - 0138

2011
Mount fuel filter console (1) with LDA and tighten screws (2).
07095

Fuel system W 07-08-02

Oil sealing ring on fuel filter lightly. Tighten fuel filter hand tight.
07099

39391 0

Plug fuel pipes and fix pipe clips (1) with clamping pliers.

Note
- Check fuel pipes and renew if necessary. - Observe assignment of the fuel pipes.

39393 0

Plug cable plug to solenoid valve (1) if available. Plug on the underpressure line (2).

1 2

39381 0
11/2004

5/6

0312 1602 - 0138

Fuel system W 07-08-02

In FL, BFL engines Mount air duct cover (1).

2011

Note
The air duct cover must be under the stand plate and the profile rubber (arrows).

39490 0

Fix air duct cover (2). Tighten screws (1).

09087

1 1

39080 0

11/2004

6/6

0312 1602 - 0138

2011
W 07-10-06

Fuel system W 07-10-06

Remove and install fuel lines (with Bosch injection pumps)

Tools
- Commercial tools 8011 - Clamping pliers

References
- W 08-08-02

Note
Collect drained operating materials in suitable vessels and dispose of according to regulations.
!

Caution!
Observe the safety regulations and and national specifications for handling fuels!

Remove fuel lines In FL, BFL engines Unscrew screws (1) and remove air duct cover (2).
2

1 1

39080 0

Remove fuel supply line Loosen pipe clip (1) and pull off fuel pipe (2).

39366 0
11/2004

1/4

0312 1604 - 0138

Fuel system W 07-10-06

Loosen hose clip and pull off return pipe (1). Unscrew hollow screws (2), remove fuel supply line (3) and sealing rings. Check components for visible signs of damage.

2011

1 3

2 2
39483 0

Install fuel supply line Push fuel supply line (1) through the profile rubber (arrow) and position. Tighten hollow screws (2) with new CU sealing rings.

1
07015

2 2

39367 0

Attach return hose (1) and fix hose clip with clamping pliers.

Note
Check return pipe, renew if necessary.

34204 1
11/2004

2/4

0312 1604 - 0138

2011
Attach fuel hose (1) and fix hose clip with clamping pliers.

Fuel system W 07-10-06

Note
Check fuel pipe and renew if necessary.

1
34205 1

In FL, BFL engines Mount air duct cover (1).

Note
The air supply cover must be under the stand plate and the profile rubber (arrows).

39490 0

Fix air duct cover (2). Tighten screws (1).

09087

1 1

39080 0
11/2004

3/4

0312 1604 - 0138

Fuel system W 07-10-06

Remove overflow pipe In FL, BFL engines Remove oil cooler Job card W 08-08-02. Loosen pipe clips (1) and pull off return pipes (2). Unscrew screws and remove overflow pipe (3). Check components for visible signs of damage.

2011
1

34031 1

Install overflow pipe Mount overflow pipe (1), attach hoses and tighten screws.
07062

Attach return hose (2) and fix hose clip with clamping pliers. Insert return hose in holder (arrows).

Note
The rubber hoses must always be renewed.

34202 1

Attach return hose (1) and fix hose clip with clamping pliers.

Note
Check return pipe, renew if necessary. In FL, BFL engines Install oil cooler Job card W 08-08-02.

34203 1
11/2004

4/4

0312 1604 - 0138

2011
W 07-10-06

Fuel system W 07-10-06

Remove and install fuel lines (with Motorpal injection pumps)

Tools
- Commercial tools 8011 - Clamping pliers
!

Caution!
Observe the safety regulations and and national specifications for handling fuels!

Note
Collect drained operating materials in suitable vessels and dispose of according to regulations.

Remove fuel lines In FL, BFL engines Unscrew screws (1) and remove air duct cover (2).
2

1 1

39080 0

Remove fuel supply line Loosen pipe clip (1) and pull off fuel pipe.

39494 0
11/2004

1/4

0312 1603 - 0138

Fuel system W 07-10-06

Unscrew hollow screws (1), remove fuel supply line (2) and sealing rings. Check components for visible signs of damage.

2011

39491 0

Install fuel supply line Push fuel supply line (1) through the profile rubber (arrow) and position. Tighten hollow screws (2) with new CU sealing rings.
07015

39438 0

Attach fuel hose (1) and fix hose clip with clamping pliers.

Note
Check fuel pipe and renew if necessary.

39439 0
11/2004

2/4

0312 1603 - 0138

2011
Remove overflow pipe In FL, BFL engines Unscrew screws (1) and remove standing plate (2).

Fuel system W 07-10-06

1
2

39081 0

Unscrew hollow screws (1), remove overflow pipe (2) and sealing rings.

6
1 1

Note
Remove overflow pipe to flywheel side. Check components for visible signs of damage.

39492 0

Install overflow pipe Mount overflow pipe (2), tighten hollow screws (1) with new CU sealing rings.

1
07061

39492 0
11/2004

3/4

0312 1603 - 0138

Fuel system W 07-10-06

In FL, BFL engines Mount the standing plate and tighten the screws.

2011
2

Note
- Note different screw length (1 and 2). - The oil cooler must be on the latch (arrow). Tighten screws (1 and 2).
09070

39493 0

Mount air duct cover (1).

Note
The air supply cover must be under the stand plate and the profile rubber (arrows).

39490 0

Fix air duct cover (2). Tighten screws (1).

09087

1 1

39080 0
11/2004

4/4

0312 1603 - 0138

2011
W 07-10-08

Fuel system W 07-10-08

Remove and install fuel filter console

Tools
- Commercial tools 8011 - Clamping pliers - Special tools 170 050 - Special wrench
!

Caution!
Observe the safety regulations and national specifications for handling fuels!

Note
Collect drained operating materials in suitable vessels and dispose of according to regulations.

Remove fuel filter console Remove fuel filter Unscrew fuel filter (1) with special wrench.

39070 0

Loosen pipe clips (1) with clamping pliers and pull off fuel pipes (2).

2
39067 0
11/2004

1/4

0312 1605 - 0138

Fuel system W 07-10-08

Unscrew screws (1) and remove fuel filter console (2). Check components for visible signs of damage.

2011
1

39068 0

Install fuel filter console Mount fuel filter console (2) and tighten screws (1).
07082

39068 0

Attach fuel pipes (2) and fix pipe clips (1) with clamping pliers.

Note
- Check fuel pipes and renew if necessary. - Observe assignment of the fuel pipes.

2
39067 0
11/2004

2/4

0312 1605 - 0138

2011
Install fuel filter Oil sealing ring on fuel filter lightly. Tighten new fuel filter hand tight.
07099

Fuel system W 07-10-08

39234 0

11/2004

3/4

0312 1605 - 0138

Fuel system W 07-10-08

Notes

2011

11/2004

4/4

0312 1605 - 0138

2011
W 07-11-01

Fuel system W 07-11-01

Remove and install fuel pump

Tools
- Commercial tools 8011 - Clamping pliers
!

Caution!
Observe the safety regulations and observe national specifications for handling fuels.

Note
Collect drained operating materials in suitable vessels and dispose of according to regulations.

Remove fuel pump Pull out oil dipstick (1). Loosen pipe clip (2) with clamping pliers and pull off fuel pipe (3).

6
1

39030 0

Unscrew screws (1). Remove fuel pump (2) and gasket. Check components for visible signs of damage.

39206 0
11/2004

1/2

0312 1606 - 0138

Fuel system W 07-11-01

Install fuel pump Clean the sealing surface on the fuel pump and crankcase. Pull new round sealing ring (arrow) onto fuel pump.

2011

39207 0

Mount fuel pump. Press in fuel pump to stop and tighten screws (1). Tighten screws.
07024

39225 0

Attach fuel hose (3) and fix hose clip (2) with clamping pliers.

Note
Check fuel pipe and renew if necessary. Insert oil dipstick (1).

39030 0
11/2004

2/2

0312 1606 - 0138

2011
W 08-04-05

Lube oil system W 08-04-05

Remove and install lube oil pump

Tools
- Commercial tools

References
- W 04-04-12 (old version) - W 04-04-12 (new version)

Note
Collect drained operating materials in suitable vessels and dispose of according to regulations.

Remove lube oil pump Remove toothed belt and clamping roller Job card W 04-04-12 (old version) Job card W 04-04-12 (new version) Pull out oil dipstick (1). Unscrew screws (2).

39621 0

Press lube oil pump (1) off the clamping sleeves (2) and remove. Check components for visible signs of damage.

39495 0
11/2004

1/4

0312 1607 - 0138

Lube oil system W 08-04-05

Install lube oil pump Clean the sealing surface on the lube oil pump and crankcase. Renew the gasket (1).

2011

1
39496 0

Check all clamping sleeves are in place (arrows).

39497 0

Insert lube oil pump (1) and attach to clamping sleeves (2).

39495 0
11/2004

2/4

0312 1607 - 0138

2011
Tighten screws (1).
08010

Lube oil system W 08-04-05

Insert oil dipstick (2). Install toothed belt and clamping roller Job card W 04-04-12 (old version) Job card W 04-04-12 (new version).

2
1

1
39498 0

11/2004

3/4

0312 1607 - 0138

Lube oil system W 08-04-05

Notes

2011

11/2004

4/4

0312 1607 - 0138

2011
W 08-04-06

Lube oil system W 08-04-06

Remove and install oil intake pipe

Tools
- Commercial tools

References
- W 08-04-07

Auxiliary material
- DEUTZ DW 74

Remove oil intake pipe Remove lube oil tray Job card W 08-04-07 Unscrew screws (1) and remove oil intake pipe (2).

39499 0

Install oil intake pipe Clean the sealing surface on the oil intake pipe and crankcase. Apply sealant DEUTZ DW 74 to the oil intake pipe (arrow).

39351 0
11/2004

1/2

0312 1608 - 0138

Lube oil system W 08-04-06

Mount oil intake pipe (1) and tighten screws (2).

2011

Note
Do not move the sealant when mounting the oil intake pipe.
08015

Install lube oil tray Job card W 08-04-07.

2
39550 0

11/2004

2/2

0312 1608 - 0138

2011
W 08-04-07

Lube oil system W 08-04-07

Remove and install lube oil tray

Tools
- Commercial tools 8189 - Torx tool kit

Auxiliary material
- DEUTZ DW 74

Note
Collect drained operating materials in suitable vessels and dispose of according to regulations.

Remove lube oil tray Unscrew locking screw (1) and drain engine oil. Tighten locking screw with new sealing ring.
03031

1
39551 0

In engines with connection housing Unscrew screws (arrows) and remove cover plate (1).

39552 0
11/2004

1/4

0312 1609 - 0138

Lube oil system W 08-04-07

Unscrew all screws (arrow) and remove lube oil tray.

2011

39628 0

Install lube oil tray Clean the sealing surface on the lube oil tray and crankcase. Apply sealant DEUTZ DW 74 (arrows).

Note
Make sure no sealant gets into the oil channel (1).

1
34253 1

Mount lube oil tray.

Note
Do not move the sealant when mounting the lube oil tray.

39553 0
11/2004

2/4

0312 1609 - 0138

2011
Pre-tighten screws at the corners (arrows).

Lube oil system W 08-04-07

Note
Pre-tighten the screws of the lube oil tray at the corners (arrows) first then tighten all the screws in order.
03030

34255 1

Tightening order 4-cylinder Tighten all bolts in the right order.

Note
Pay attention to different screw length for cast oil tray.
03030

34256 1

Tightening order 4-cylinder (cast oil tray with cylinder head screws) Tighten all screws in the right order.

Note
Note different screw length.

03030

34257 1
11/2004

3/4

0312 1609 - 0138

Lube oil system W 08-04-07

Tightening order 3-cylinder Tighten all screws in the right order.
03030

2011

34258 1

Tightening order 2-cylinder Tighten all screws in the right order.

03030

34259 1

In engines with connection housing Fit cover plate (1) and tighten screws (arrows).
03085

Fill in prescribed engine oil.

39552 0
11/2004

4/4

0312 1609 - 0138

2011
W 08-08-02

Lube oil system W 08-08-02

Remove and install oil cooler

Tools
- Commercial tools 8189 - Torx tool kit

Note
Collect drained operating materials in suitable vessels and dispose of according to regulations.

Remove oil cooler Unscrew screws (1) and remove air duct cover.

1 1

39080 0

Unscrew screws (1) and remove standing plate (2).

1
2

39081 0
11/2004

1/6

0312 1610 - 0138

Lube oil system W 08-08-02

Unscrew screws (1) and pull oil cooler up.

2011

39554 0

Pull connections (1) out of crankcase.

1 1

39556 0

Install oil cooler Check connections for visible signs of damage.

39557 0
11/2004

2/6

0312 1610 - 0138

2011
Press connections (1) into the crankcase to the stop.

Lube oil system W 08-08-02

Note
The side with the long joint X must face upwards.

39281 0

Press the oil cooler onto the connections to the stop.

Note
Insert connections (1) in the bores (arrows).

39622 0

Turn on screws (1).

Note
Do not tighten screws.

39559 0
11/2004

3/6

0312 1610 - 0138

Lube oil system W 08-08-02

Mount the standing plate and turn on the screws.

2011
2

Note
- Note different screw length (1 and 2). - The oil cooler must be on the latch (arrow).

1
09070

39493 0

Tighten screws (1 and 3).

09070

3 2

Tighten screws (2).

08051

39623 0

Mount air duct cover (1).

Note
The air duct cover must be under the stand plate and the profile rubber (arrows).

39490 0
11/2004

4/6

0312 1610 - 0138

2011
Fix air duct cover (2). Tighten screws (1).
09087

Lube oil system W 08-08-02

1 1

39080 0

11/2004

5/6

0312 1610 - 0138

Lube oil system W 08-08-02

Notes

2011

11/2004

6/6

0312 1610 - 0138

2011
W 08-10-06

Lube oil system W 08-10-06

Remove and install oil filter cartridge

Tools
- Commercial tools - Special tools 170 050 - Special wrench

Note
Collect drained operating materials in suitable vessels and dispose of according to regulations.

Remove oil filter cartridge Unscrew oil filter cartridge (1) with special device (2).

39040 0

Install oil filter cartridge Oil the sealing ring of the new oil filter cartridge lightly and screw on hand tight.
08001

39229 0
11/2004

1/2

0312 1611 - 0138

Lube oil system W 08-10-06

Notes

2011

11/2004

2/2

0312 1611 - 0138

2011
W 08-11-02

Lube oil system W 08-11-02

Remove and install oil pressure regulating valve, check

Tools
- Commercial tools Caliper gauge

Note
Collect drained operating materials in suitable vessels and dispose of according to regulations.

Note
Overview of valve row assignment - An oil pressure regulating valve (1) is installed as standard in the upper oil channel. The lower oil channels are empty and sealed. - In engines with a heater connection, additional oil pressure regulating valves (2) are available in the lower two oil channels as well as a transfer nipple for supply (3) and return (4).

6
1 3

4 2

39520 0

Remove oil pressure regulating valve (without heater connection) Unscrew cap (1), remove compression spring and valve piston.

Note
When removing the cap the following parts may jump out under the pressure of the compression spring.

39060 0
11/2004

1/8

0312 1612 - 0138

Lube oil system W 08-11-02

Check components for visible signs of wear.

2011

39061 0

Measure length of the compression spring with caliper gauge.

Note
If the wear limit is reached, the compression spring has to be changed.
08 44

39062 0

Install oil pressure regulating valve (without heater connection) Insert valve piston (1) and compression spring (2).

Note
- Use compression spring with green mark (3 bar opening pressure). - Oil the valve piston lightly. - Note installation order.
08 41

34076 1
11/2004

2/8

0312 1612 - 0138

2011
Tighten cap (1) with new CU sealing ring.
08098

Lube oil system W 08-11-02

39060 0

Note
In engines without heater connection no oil pressure regulating valves are available in the valve row and the oil channels are fitted with a cap (1).
08098

39065 0

Remove oil pressure regulating valves (with heater connection) Unscrew caps (1) and remove sealing rings.

34081 1
11/2004

3/8

0312 1612 - 0138

Lube oil system W 08-11-02

Unscrew transfer nipple (1) for heater supply and remove sealing ring. Unscrew transfer nipple (2) for heater return and remove sealing ring.

2011

Note
When removing the transfer nipple (2) the following parts may jump out under the pressure of the compression spring.

34080 1

Unscrew caps (1) and remove sealing ring.

Note
When removing the cap the following parts may jump out under the pressure of the compression spring.

34079 1

Remove compression springs and valve piston (1).

Note
Set down the components in the order of installation.

34078 1
11/2004

4/8

0312 1612 - 0138

2011
Check components for visible signs of wear.

Lube oil system W 08-11-02

39061 0

Measure length of the compression springs with caliper gauge.

Note
If the wear limit is reached, the compression spring has to be changed.
08 44 08 45 08 46

39062 0

Install oil pressure regulating valves (with heater connection) Insert valve piston and compression springs (1, 2 and 3).

Note
- Note the assignment of the compression springs Item 1 2 3 Opening pressure 1.0 bar 1.7 bar 0.3 bar Color marking yellow red blue

39518 0
11/2004

5/8

0312 1612 - 0138

Lube oil system W 08-11-02

Note
- Note installation position of the valve pistons (arrows). - Oil the valve piston lightly.
08 41 08 42 08 43

2011

39518 0

Tighten caps (1) with new CU sealing rings.

08098

34079 1

Install new sealing rings (1) at the transfer nipple.

Note
The countersink on the sealing rings (arrow) must face the crankcase.

1
39519 0
11/2004

6/8

0312 1612 - 0138

2011
Tighten the transfer nipple (1) for the heater supply. Tighten transfer nipple (2), with valve seat, for heater return.

Lube oil system W 08-11-02

1
08061

34080 1

Tighten caps (1) with new CU sealing rings.

08062

34081 1

11/2004

7/8

0312 1612 - 0138

Lube oil system W 08-11-02

Notes

2011

11/2004

8/8

0312 1612 - 0138

2011
W 08-11-07

Lube oil system W 08-11-07

Remove and install oil filter console

Tools
- Commercial tools

References
- W 08-10-06

Note
Collect drained operating materials in suitable vessels and dispose of according to regulations.

Remove oil filter console Remove oil filter cartridge Job card W 08-10-06. Unscrew hollow screw (1) and remove sealing rings.

39042 0

Unscrew screws (1) and remove oil filter console (2).

1 1

39043 0
11/2004

1/2

0312 1613 - 0138

Lube oil system W 08-11-07

Remove gasket (1). Check components for visible signs of damage.

2011

39044 0

Install oil filter console Clean the sealing surface of the oil filter console and crankcase.

1
Mount oil filter console (2) with new gasket and tighten screws (1).
08003

39043 0

Tighten hollow screw (1) with new CU sealing rings.

08048

Install oil filter cartridge Job card W 08-10-06.

39042 0
11/2004

2/2

0312 1613 - 0138

2011
W 08-11-08

Lube oil system W 08-11-08

Remove and install oil pressure switch

Tools
- Commercial tools

Note
Collect drained operating materials in suitable vessels and dispose of according to regulations.

Remove oil pressure switch Pull cable plug (1) out of oil pressure switch (2).

39051 0

Unscrew oil pressure switch (1) with sealing ring. Check component for visible signs of damage.

39230 0
11/2004

1/2

0312 1614 - 0138

Lube oil system W 08-11-08

Install oil pressure switch Tighten oil pressure switch (2) with sealing ring.
08091

2011

Plug cable plug (1) to oil pressure switch.

39051 0

11/2004

2/2

0312 1614 - 0138

2011
W 08-11-09

Lube oil system W 08-11-09

Remove and install oil pressure sensor

Tools
- Commercial tools - Special tools 170 110 - Special wrench

Note
Collect drained operating materials in suitable vessels and dispose of according to regulations.

Remove oil pressure sensor Pull off cable plug from oil pressure sensor (1) if available.

39524 0

Unscrew oil pressure sensor (1) with special wrench and remove sealing ring. Check components for visible signs of damage.

39525 0
11/2004

1/2

0312 1615 - 0138

Lube oil system W 08-11-09

Install oil pressure sensor Mount oil pressure sensor (1) with new CU sealing ring and tighten with special wrench.
08093

2011

39525 0

Plug cable plug to oil pressure sensor (1) if available.

39524 0

11/2004

2/2

0312 1615 - 0138

2011
W 08-11-12

Lube oil system W 08-11-12

Remove and install oil thermostat (oil cooler)

Tools
- Commercial tools Caliper gauge

Auxiliary material
- Assembly sleeve

Note
Collect drained operating materials in suitable vessels and dispose of according to regulations.

Remove oil thermostat (oil cooler) In FL, BFL engines Unscrew screws (1) and remove air duct cover (2).
2

1 1

39080 0

Unscrew screws (1) and remove standing plate (1).

1
2

39081 0
11/2004

1/4

0312 1617 - 0138

Lube oil system W 08-11-12

Unscrew cap (1), remove oil thermostat with compression spring.

2011

Note
When removing, the following parts may jump out under the pressure of the compression spring.

39083 0

Check components for visible signs of wear.

39437 0

Measure length of the compression spring with caliper gauge.

Note
If the wear limit is reached, the compression spring has to be changed.
08 74

39085 0
11/2004

2/4

0312 1617 - 0138

2011
Install oil thermostat (oil cooler) Insert oil thermostat (1) with compression spring.

Lube oil system W 08-11-12

Note
- Oil the oil thermostat lightly. - Note installation order.

39086 0

Pull the new round sealing ring onto the cap.

Note
Use the assembly sleeve.

1
Tighten locking screw (1).
08072

39083 0

In FL, BFL engines Mount the standing plate and turn on the screws.

Note
- Note different screw length (1 and 2). - The oil cooler must be on the latch (arrow). Tighten screws (1 and 2).
09070

39493 0
11/2004

3/4

0312 1617 - 0138

Lube oil system W 08-11-12

Mount air duct cover (1).

2011

Note
The air duct cover must be under the stand plate and the profile rubber (arrows).

39490 0

Fix air duct cover (2). Tighten screws (1).

09087

1 1

39080 0

11/2004

4/4

0312 1617 - 0138

2011
W 08-15-01

Lube oil system W 08-15-01

Remove and install oil pressure line (turbocharger)

Tools
- Commercial tools

Note
Collect drained operating materials in suitable vessels and dispose of according to regulations.

Remove oil pressure l-ine Unscrew hollow screws (1), remove oil pressure line (2) and sealing rings. Check components for visible signs of damage.

6
2

1
39397 0

Install oil pressure line Mount oil pressure line (2), tighten hollow screws (1) with new CU sealing rings.
08042

1
39397 0
11/2004

1/2

0312 1618 - 0138

Lube oil system W 08-15-01

Notes

2011

11/2004

2/2

0312 1618 - 0138

2011
W 08-15-02

Lube oil system W 08-15-02

Remove and install oil return line (turbocharger)

Tools
- Commercial tools

Note
Collect drained operating materials in suitable vessels and dispose of according to regulations.

Remove oil return line Unscrew screw (1) and remove holder.

39395 0

Pull oil return line (1) out of the crankcase and pull off from oil return pipe flange support (2).

2 1

39396 0
11/2004

1/4

0312 1619 - 0138

Lube oil system W 08-15-02

Unscrew screws (1), remove oil return pipe flange support (2) and gasket. Check components for visible signs of damage.

2011

39398 0

Install oil return line Clean the sealing surface of the turbocharger and oil return pipe flange support. Mount oil return pipe flange support (1) with new gasket and tighten screws (2).
08044

39627 0

Pull new round sealing ring (arrow) onto oil return pipe flange support.

39399 0
11/2004

2/4

0312 1619 - 0138

2011
Pull new round sealing ring (arrow) onto oil return line.

Lube oil system W 08-15-02

39378 0

Push oil return line (1) onto oil return line flange support (2) and insert in crankcase.

Note
Oil round sealing rings lightly.

2 1

39396 0

Mount holder and tighten screw (1).

08046

39395 0
11/2004

3/4

0312 1619 - 0138

Lube oil system W 08-15-02

Notes

2011

11/2004

4/4

0312 1619 - 0138

2011
W 08-16-01

Lube oil system W 08-16-01

Remove and install oil line for injection adjuster supply

Tools
- Commercial tools

Note
Collect drained operating materials in suitable vessels and dispose of according to regulations.

Remove oil line Pull cable plug (1) out oil pressure switch. Unscrew screws (2), remove fuel filter console (3) and hang aside.

6
1
2

39200 0

Unscrew hollow screws (1), remove oil line (2) and sealing rings. Check components for visible signs of damage.

39202 0
11/2004

1/2

0312 1620 - 0138

Lube oil system W 08-16-01

Install oil line Mount oil line (2), tighten hollow screws (1) with new CU sealing rings.
08048

2011
2

39202 0

Fit fuel filter console (3) and tighten screws (2).

07082

1
2

Plug cable plug (1) to oil pressure switch.

39200 0

11/2004

2/2

0312 1620 - 0138

2011
W 08-16-02

Lube oil system W 08-16-02

Remove and install oil temperature sensor (in engines with injection adjustment)
Tools
- Commercial tools Caliper gauge

Note
Collect drained operating materials in suitable vessels and dispose of according to regulations.

Remove oil temperature sensor (injection adjustment) Unscrew cap (1), remove oil temperature sensor with compression spring and remove slide regulator.

Note
When removing, the following parts may jump out under the pressure of the compression spring.

39045 0

Check components for visible signs of wear. - 1 temperature sensor - 2 pressure spring - 3 slide regulator

39047 0
11/2004

1/2

0312 1637 - 0138

Lube oil system W 08-16-02

Measure length of the compression spring with caliper gauge.

2011

Note
If the wear limit is reached, the compression spring has to be changed.
08 74

39062 0

Install oil temperature sensor (injection adjustment) Insert temperature sensor, compression spring and slide regulator.

Note
- Oil temperature sensor lightly. - Note installation order. Tighten locking screw (1) with new CU sealing ring.
08053

39045 0

11/2004

2/2

0312 1637 - 0138

2011
W 08-11-11

Lube oil system W 08-11-11

Remove and install oil temperature sensor

Tools
- Commercial tools

References
- W 08-08-02

Note
Collect drained operating materials in suitable vessels and dispose of according to regulations.

Remove oil temperature sensor In FL, BFL engines Remove oil cooler Job card W 08-08-02. Unscrew screw (1).

1
39481 0

Unscrew screws (1) and remove air duct (2).

39468 0
11/2004

1/4

0312 1616 - 0138

Lube oil system W 08-11-11

Pull cable plugs (1and 2) from the oil temperature sensor.

2011

Note
Note the assignment of the cable plugs.

1 2

39266 0

Unscrew oil temperature sensor (1) and remove sealing ring.

39265 0

Check components for visible signs of damage.

39096 0
11/2004

2/4

0312 1616 - 0138

2011
Install oil temperature sensor Tighten oil temperature sensor (1) with new sealing ring.
08095

Lube oil system W 08-11-11

39265 0

Plug cable plugs (1 and 2) into oil temperature sensor (2).

Note
Note the assignment of the cable plugs.

1 2

39266 0

In FL, BFL engines Mount air duct (2) and tighten screws (1).

39468 0
11/2004

3/4

0312 1616 - 0138

Lube oil system W 08-11-11

Tighten screw (1).

2011

1
39481 1

Pre-tighten screw (1) on cylinder head and tighten screws (arrows).

09089

Tighten screw (1) on cylinder head.

09089

Install oil cooler Job card W 08-08-02.

34215 1

11/2004

4/4

0312 1616 - 0138

2011
W 09-11-01

Cooling system W 09-11-01

Remove and install cooling blower

Tools
- Commercial tools 8189 - Torx tool kit

References
- W 12-02-01 (FL, BFL engines)

Remove cooling blower Remove V-belt Job card W 12-02-01. Unscrew screws (1) and remove air duct cover (2).
2

1 1

39080 0

Remove cable from generator. Unscrew nut (1) and remove cable G1.W (2). Unscrew nut (3) and remove cable G1.D+ (4).

3 4

39560 0
11/2004

1/4

0312 1621 - 0138

Cooling system W 09-11-01

Unclip cable plug (1).

2011

1
39561 0

Unscrew screws (1) and remove cable holders (arrows).

39611 0

Unscrew screws (1) and remove cooler blower with generator. Check components for visible signs of damage.

1
39562 0
11/2004

2/4

0312 1621 - 0138

2011
Install cooling blower Mount cooler blower with generator and tighten screws.
09066

Cooling system W 09-11-01

39564 0

Position cable holders (arrows) and tighten screws.

Note
Note different screw length: Screw M6 x 12 mm (1) Screw M8 x 20 mm (2) Tighten screw (1 and 2).
13092

39271 0

Clip in cable plug (1).

1
39561 0
11/2004

3/4

0312 1621 - 0138

Cooling system W 09-11-01

Plug cable to generator. Attach cable "G1.D+" (4) and tighten nut (3).
13082

2011

Attach cable "G1.W" (2) and tighten nut (1).

13083

3 4

39560 0

Mount air duct cover (1).

Note
The air duct cover must be under the stand plate and the profile rubber (arrows).

39490 0

Fix air duct cover (2). Tighten screws (1).

09087

Install V-belt. Job card W 12-02-01.

1 1

39080 0
11/2004

4/4

0312 1621 - 0138

2011
W 09-11-02

Cooling system W 09-11-02

Dismantle and complete cooling blower, check

Tools
- Commercial tools 8189 - Torx tool kit

References
- W 09-11-01

Dismantle cooling blower Remove cooling blower Job card W 09-11-01. Unscrew screws (arrows) and remove blower jacket inlet (1).

39565 0

Unscrew nut (1).

Note
Hold shaft.

39566 0
11/2004

1/8

0312 1622 - 0138

Cooling system W 09-11-02

Remove disc (1), V-belt pulley (2) and running wheel (3).

2011
1

39567 0

Remove spacer disc (1).

39568 0

Remove guide disc (1).

39569 0
11/2004

2/8

0312 1622 - 0138

2011
Unscrew nut (1) and press out rubber muff (1).

Cooling system W 09-11-02

39570 0

Unscrew nuts (1) and press out generator. Visually inspect components and renew if necessary.

39571 0

Complete cooler blower Insert generator and press in to stop.

Note
Note installation position of the generator.

39572 0
11/2004

3/8

0312 1622 - 0138

Cooling system W 09-11-02

Mount washers and tighten nuts (1) alternately.

2011

Note
Check the installation position again.

1
09065

39571 0

Mount guide disc (1).

Note
The stepped side (arrow) must face the generator.

39573 0

Mount spacer disc (1).

39574 0
11/2004

4/8

0312 1622 - 0138

2011
Mount running wheel (3), V-belt pulley (2) and disc.

Cooling system W 09-11-02

1

Note
Note installation position.

39567 0

Tighten nut.
13021

39575 0

Check gap dimension Press out the protective grille (1) carefully from the blower jacket inlet at the fastening points (arrows).

Note
Do not damage the protective grille.

39576 0
11/2004

5/8

0312 1622 - 0138

Cooling system W 09-11-02

Mount blower jacket inlet (1) and tighten screws (2).

2011

Note
Note the installation position, the gates (arrows) must be in line.

1
09067

2 2

39577 0

Measure the gap dimension with a feeler gauge between the running wheel and the blower jacket inlet.
09 91

39578 0

Compensate gap dimension with the appropriate spacer disc (1).

Note
Spacer discs of 5 to 7 mm are available.

39574 0
11/2004

6/8

0312 1622 - 0138

2011
Press the protective grille (1) carefully into the blower jacket inlet.

Cooling system W 09-11-02

Note
Observe the fastening points.

39579 0

Insert rubber muff (1) and tighten nut (2).

13081

6
1

Install cooler blower Job card W 09-11-01.

39580 0

11/2004

7/8

0312 1622 - 0138

Cooling system W 09-11-02

Notes

2011

11/2004

8/8

0312 1622 - 0138

2011
W 09-13-01

Cooling system W 09-13-01

Dismantle and complete fan drive

Tools
- Commercial tools

Dismantle fan drive If available, unscrew screws (arrows) and remove fan.

34014 1

Unscrew screws (arrows) and remove V-belt pulley.

34005 1
11/2004

1/4

0312 1623 - 0138

Cooling system W 09-13-01

Remove locking ring (arrow).

2011

34006 0

Press out ball bearing with shaft (arrow).

34007 1

Pull the inner (1) and outer (2) ball bearing from the shaft.

2
Check components for visible signs of damage.

Note
The ball bearings must always be renewed.

39008 1
11/2004

2/4

0312 1623 - 0138

2011
Complete fan drive Press the inner ball bearing (1) over the outer ring up to the stop.

Cooling system W 09-13-01

34009 1

Press in the shaft (1) to the stop in the inner ball bearing.

6
1

Note
- Note installation position of the shaft. - Support the inner ring of the ball bearing when pressing in.

34010 1

Press in the outer ball bearing (1) over the outer and inner ring up to the stop.

34011 1
11/2004

3/4

0312 1623 - 0138

Cooling system W 09-13-01

Insert locking ring (arrow).

2011

Note
Pay attention to correct fit of the locking ring in the groove.

34006 0

Mount V-belt pulley and tighten screws (arrows).

12046

34005 1

Mount fan if available and tighten screws (arrows).

Note
Note different strength classes of the screws.

09041

34014 1
11/2004

4/4

0312 1623 - 0138

2011
W 11-00-03

Monitoring system W 11-00-03

Remove and install lifting magnet (shutoff magnet)

Tools
- Commercial tools

References
- W 12-02-06 - W 13-02-03 (FM, BFM engines)

Remove lifting magnet (shutdown magnet) In FM, BFM engines Remove generator Job card W 13-02-03. In FL, BFL engines Remove V-belt clamping roller Job card W 12-02-06. Unscrew screw (arrow) and pull off cable plug (1).

39038 0

Unscrew screws (1) and remove lifting magnet (2). Check components for visible signs of damage.

1
39039 0
11/2004

1/2

0312 1624 - 0138

Monitoring system W 11-00-03

Pull new round sealing ring (1) onto lfiting magnet.

2011

39036 0

Install lifting magnet Insert lifting magnet (2) and tighten screws (1).

1
05041

1
39039 0

Plug cable plug (1) and tighten screw (arrow). In FL, BFL engines Install V-belt clamping roller Job card W 12-02-06. In FM, BFM engines Install generator Job card W 13-02-03.

39038 0
11/2004

2/2

0312 1624 - 0138

2011
W 12-02-01

Other components W 12-02-01

Check V-belt, renew (in FL and BFL engines)

Tools
- Commercial tools 8115 - V-belt pulley tension measuring appliance
!

Caution!
Only test / tighten / renew V-belts with the engine at a standstill.

Note
The V-belt tension of new V-belts must be checked after they have been running for 15 minutes.

Test V-belt Inspect the V-belt visually for wear all round.

39626 0

Renew V-belt Loosen screws (1). Swing V-belt clamping roller (2) to the side (arrow). Remove V-belt.

39276 0
11/2004

1/4

0312 1625 - 0138

Other components W 12-02-01

Fit V-belt. Tighten V-belt. Press the V-belt clamping roller (1) in the direction of the arrow with a suitable tool and tighten the screw (2).
12041

2011

39581 0

Check the V-belt tension with the V-belt tension measuring appliance. Lower indicator arm (1) into V-belt tension measuring appliance (2).

39582 0

Mount V-belt tension measuring appliance on the V-belt.

Note
The V-belt must be between the guides (arrow).

39583 0
11/2004

2/4

0312 1625 - 0138

2011
Press the V-belt measuring appliance against the V-belt with the button (1) until you hear it click. Read the measured value at the point of intersection of the indicator arm and the scale (arrow).

Other components W 12-02-01

Note
Note different unit on the scale.

12 11

12 21

If the setpoint is not reached, the clamping procedure must be repeated.

39584 0

Tighten screw (1).

12041

6
1

39585 0

11/2004

3/4

0312 1625 - 0138

Other components W 12-02-01

Notes

2011

11/2004

4/4

0312 1625 - 0138

2011
W 12-02-01

Other components W 12-02-01

Check, renew V-belt (in FM, BFM engines)

Tools
- Commercial tools 8115 - V-belt pulley tension measuring appliance
!

Caution!
Only test / tighten / renew V-belts with the engine at a standstill.

Note
- The V-belt tension of new V-belts must be checked after they have been running for 15 minutes. - One variant has been described. The procedure is the same accordingly for other variants.

Test V-belt Inspect the V-belt visually for wear all round.

39370 0

Renew V-belt Loosen screws (1). Loosen screw (2).

Note
Hold nuts (arrow).

3
39371 0
11/2004

1/4

0312 1626 - 0138

Other components W 12-02-01

Swing generator aside (arrow). Remove V-belt.

2011

39372 0

Fit V-belt. Tighten V-belt. Push back generator with suitable tool (arrow) and tighten screw (1).

Note
Hold nuts.

13015

1
39373 0

Check the V-belt tension with the V-belt tension measuring appliance. Lower indicator arm (1) into V-belt tension measuring appliance (2).

39582 0
11/2004

2/4

0312 1626 - 0138

2011
Mount V-belt tension measuring appliance on the V-belt.

Other components W 12-02-01

Note
The V-belt must be between the guides (arrow).

39522 0

Press the V-belt measuring appliance against the Vbelt with the button (1) until you hear it click. Read the measured value at the point of intersection of the indicator arm and the scale (arrow).

Note
Note different unit on the scale.

12 11

12 21

If the setpoint is not reached, the clamping procedure must be repeated.

39523 0

Tighten screw (1).

13012

Tighten screws (2).

13017

Tighten screw (3).

Note
Hold nuts (arrow).

2
13015

3
39371 0

11/2004

3/4

0312 1626 - 0138

Other components W 12-02-01

Generator fastening with built-up fan drive (unit design) Tighten screw (1).
13016

2011

1 2

Tighten screw (2).

13015

Tighten screw (3).

3
13012

34289 1

Generator fastening with built-up fan drive (building machine design)

1
Tighten screw (1).
13012

Tighten screw (2).

13016

Tighten screw (3).

2
13015

34292 1

11/2004

4/4

0312 1626 - 0138

2011
W 12-02-06

Other components W 12-02-06

Remove and install V-belt clamping roller

Tools
- Commercial tools

References
- W 12-02-01 FL and BFL engines - W 12-02-01 FM and BFM engines

Note
- Only the old version of the clamping roller has been described. - The procedure is the same accordingly for other versions.

Remove V-belt clamping roller Unscrew screws (1) and remove V-belt clamping roller (2).

6
1

Check component for visible signs of damage.

39630 0

Install V-belt clamping roller Fit V-belt clamping roller (2) and tighten screws (1). Tighten V-belt. Job card W 12-02-01 (FL and BFL engines) Job card W 12-02-01 (FM and BFM engines).

39630 0
11/2004

1/2

0312 1627 - 0138

Other components W 12-02-06

Notes

2011

11/2004

2/2

0312 1627 - 0138

2011
W 12-06-01

Other components W 12-06-01

Remove and install flywheel

Tools
- Commercial tools - Special tools Guide pin (self made) 143 100 - Pressing device

Remove flywheel Unscrew all screws (arrow).

Note
Block flywheel with suitable tool. Remove flywheel.

34065 1

Remove stuck flywheel Turn in self-made guide pin (arrow). Apply pressing tool (1) and tighten screws (2).

2 2

34066 2
11/2004

1/2

0312 1628 - 0138

Other components W 12-06-01

Press down flywheel by turning in the center screw (1). Remove pressing tool. Unscrew self-made guide pin (arrow). Visually inspect the flywheel and toothed starter ring for damage.

2011

34066 1

Install flywheel Mount flywheel using a self-made guide pin (arrow).

34224 1

Tighten all screw with angled wrench alternately.

Note
- Use new screws. - Block flywheel with suitable tool.
12001

34225 1
11/2004

2/2

0312 1628 - 0138

2011
W 12-06-03

Other components W 12-06-03

Renew toothed starter at flywheel ring

Tools
- Commercial tools
!

Caution!
Risk of injury! From hot parts.

References
- W 12-06-01

Remove toothed starter ring Remove flywheel Job card W 12-06-01. Drill toothed starter ring.

Note
Do not damage the flywheel.

33837 1

Remove toothed starter ring with suitable tool.

33838 1
11/2004

1/2

0312 1629 - 0138

Other components W 12-06-03

Clean the flywheel and inspect visually at the joint (arrow).

2011

33839 1

Install toothed starter ring Heat up toothed starter ring to max. 220 C. Mount toothed starter ring and contact at collar. Install flywheel. Job card W 12-06-01.

33840 0

11/2004

2/2

0312 1629 - 0138

2011
W 12-08-02

Other components W 12-08-02

Remove and install hydraulic pump

Tools
- Commercial tools

Auxiliary material
- Graphite grease G 500, 20g tube

Remove hydraulic pump Unscrew hexagon bolts (1), remove hydraulic pump (2) and coupling sleeve.

39090 0

Visually inspect hydraulic pump (1), coupling sleeve (2) and jackets (3) for damage, change if necessary.

1 2

39091 0
11/2004

1/4

0312 1630 - 0138

Other components W 12-08-02

Install hydraulic pump Pull jackets (1 and 2) onto coupling sleeve (3).

2011

Note
The punch-out of the jackets must be aligned to the teeth of the coupling sleeve. Grease the inside teeth of the coupling sleeve with graphite grease G 500.

39092 0

Grease the toothed shaft with graphite grease G 500. Plug the coupling sleeve (2) to the toothed shaft.

Note
- Note installation position. - The teeth of the coupling sleeve must engage the toothed shaft.

34243 1

Insert hexagon bolts in the hydraulic pump. Check the protrusion of the bolts.

Note
The maximum protrusion X may not be greater than 18 mm, renew bolts if necessary or place additional washers under the bolt head.

34244 1
11/2004

2/4

0312 1630 - 0138

2011
Grease the toothed shaft of the hydraulic pump drive with graphite grease G 500. Insert hydraulic pump (2) with coupling sleeve and tighten hexagon bolts (1).

Other components W 12-08-02

Note
The teeth of the coupling sleeve must engage the hydraulic pump drive.

12051

39090 0

11/2004

3/4

0312 1630 - 0138

Other components W 12-08-02

Notes

2011

11/2004

4/4

0312 1630 - 0138

2011
W 12-08-03

Other components W 12-08-03

Remove and install toothed belt and clamping roller of the hydraulic pump
Tools
- Commercial tools
!

Caution!
The toothed belt and the clamping roller must be renewed after every disassembly regardless of their time in operation.

References
- W 12-02-01 (FL, BFL engines) - W 12-02-01 (FM, BFM engines)

Remove toothed belt and clamping roller Remove V-belt Job card W 12-02-01 (FL, BFL engines) Job card W 12-02-01 (FM, BFM engines) In FM, BFM engines If available, unscrew screws (1) and remove fan.

39625 0

Unscrew screws (1), flange hub (2) and remove V-belt pulley.

2 1
39461 0
11/2004

1/8

0312 1631 - 0138

Other components W 12-08-03

Unscrew screws (1) and remove V-belt pulley (2).

2011

Note
Hold at the center screw.

1
39354 0

Remove centrifugal disc (1).

39355 0

Unscrew screws (1) and remove protective cover (2).

1
39275 0
11/2004

2/8

0312 1631 - 0138

2011
Remove adapter (1).

Other components W 12-08-03

39601 0

Unscrew screw (1) and remove clamping roller (2). Remove toothed belt (3). Check components for visible signs of damage.

6
1 2

3
39590 0

Install toothed belt and clamping roller Insert new clamping roller with the guide fork (1) of the base plate in the guide pin (2) of the hydraulic pump console.

1 2
39591 0
11/2004

3/8

0312 1631 - 0138

Other components W 12-08-03

Screw in screw (1) and position setting eccenter (arrow) at 12.00 h position. Pre-tighten screw.
12052

2011

39592 0

Mount new toothed belt.

Note
Note running direction of the toothed belt. The labeling (arrow) on the toothed belt must be legible from the front.

39593 0

Align the toothed belt so that it is touching the crankshaft gear wheel at the guide joint (1) and the hydraulic pump gear about 4 mm behind the front edge (arrow).

39594 0
11/2004

4/8

0312 1631 - 0138

2011
Remove locking pin (1).

Other components W 12-08-03

34235 1

Turn the setting eccenter in the direction of the arrow (counterclockwise) until the pointer of the clamping roller is in line with the notch (1).

Note
Turn the setting eccenter at the hexagon socket. Tighten screw (2).
12052

1
39595 0

Turn the crankshaft 2 turns in the engines direction of rotation (arrow). Check the toothed belt tension.

Note
- The pointer of the clamping roller must be in line with the notch (1). - If the marks are not in line, the toothed belt tension must be corrected.

39596 0
11/2004

5/8

0312 1631 - 0138

Other components W 12-08-03

Correct the toothed belt tension Loosen screw (2) and pre-tighten again.
12052

2011

Turn the setting eccenter in the direction of the arrow (counterclockwise) until the pointer of the clamping roller is in line with the notch (1). Tighten screw (2).
12052

1
39595 0

Mount adapter (1).

Note
The flattened side (arrow) must face the toothed belt.

1
39597 0

Mount protective cover (2) and tighten screws (1).

Note
Pay attention to the correct fitting of the protective cover.

12056

1
39275 0
11/2004

6/8

0312 1631 - 0138

2011
Mount centrifugal disc (1).

Other components W 12-08-03

Note
The hollow gorge must face the adapter.

1
39598 0

Fit V-belt pulley (1) and tighten screws (2) alternately.

6
1 2

Note
Hold at the center screw.

12031

39599 0

In FM, BFM engines If available, mount V-belt pulley and flange hub (1). Tighten (2) screws alternately.
12031

2 1

2
39462 0
11/2004

7/8

0312 1631 - 0138

Other components W 12-08-03

Mount fan and disc, tighten screws (1).
09042

2011

Install V-belt. Job card W 12-02-01 (FL, BFL engines) Job card W 12-02-01 (FM, BFM engines)

39624 0

11/2004

8/8

0312 1631 - 0138

2011
W 13-01-02

Electrical system W 13-01-02

Remove and install cable harness

Tools
- Commercial tools

Note
The repair procedure refers to FL, BFL engines. In FM, BFM engines the repair procedure must be performed accordingly.

Unscrew screws (1) and remove air duct cover (2).

1 1

39080 0

Remove cable harness Remove cable from generator. Unscrew nut (1) and remove cable G1.W (2). Unscrew nut (3) and remove cable G1.D+ (4).

3 4

39560 0
11/2004

1/8

0312 1632 - 0138

Electrical system W 13-01-02

Unclip cable plug (1).

2011

1
39561 0

Pull out cable plug (1), with black housing, with cable "B3.WK" from the oil temperature sensor. Pull out the cable plug (2), without housing, with cable B3.G from the oil temperature sensor.

39444 0

Pull out the cable plug (1) with cable "F1/B6.WK" from the oil pressure switch.

Note
If available, pull out the cable plug with cable F1/B6.WK and cable plug with cable B6.G from the oil pressure sensor. Pull out the cable plug (2) from the release magnet.

39443 0
11/2004

2/8

0312 1632 - 0138

2011
Pull off cable plug from solenoid valve (1) if available.

Electrical system W 13-01-02

39665 0

Unscrew screw (1) and remove cable plug (2) from engine shutdown.

394410

Pull off profile rubber (1) from the clamping pins and remove the cable harness.

39442 0
11/2004

3/8

0312 1632 - 0138

Electrical system W 13-01-02

Visually inspect the cable harness.

2011

Note
The connections to the cable harness depend on the engine requirements.

39440 0

Install cable harness Insert the cable harness in the profile rubber (1) and plug the profile rubber to the clamping pins.

39442 0

Plug the cable plug (2) to the engine shutdown and tighten the screw (1).

394410
11/2004

4/8

0312 1632 - 0138

2011
Plug cable plug to solenoid valve (1) if available.

Electrical system W 13-01-02

39665 0

Plug the cable plug (1) with cable "F1/B6.WK" to the oil pressure switch.

Note
If available, plug the cable plug with cable F1/ B6.WK and cable plug with cable B6.G to the oil pressure sensor. Plug the cable plug (2) with cable to the release magnet.

39443 0

Plug cable plug (1), with black housing, with cable "B3.WK" to the oil temperature sensor. Plug the cable plug (2), without housing, with cable B3.G to the oil temperature sensor.

39444 0
11/2004

5/8

0312 1632 - 0138

Electrical system W 13-01-02

Clip in cable plug (1).

2011

1
39561 0

Connect cable to generator. Attach cable "G1.W" (4) and tighten nut (3) .
13083

Attach cable "G1.D+" (2) and tighten nut (1).

13082

3 4

39560 0

Mount air duct cover (1).

Note
The air duct cover must be under the stand plate and the profile rubber (arrows).

39490 0
11/2004

6/8

0312 1632 - 0138

2011
Fix air duct cover (2). Tighten screws (1).
09087

Electrical system W 13-01-02

1 1

39080 0

11/2004

7/8

0312 1632 - 0138

Electrical system W 13-01-02

Notes

2011

11/2004

8/8

0312 1632 - 0138

2011
W 13-02-03

Electrical system W 13-02-03

Remove and install generator (in FL and BFL engines)

Tools
- Commercial tools 8189 - Torx tool kit

References
- W 12-02-01

Remove generator Remove V-belt Job card W 12-02-01. Unscrew screws (1) and remove air duct cover (2).
2

1 1

39080 0

Remove cable from generator. Unscrew nut (1) and remove cable G1.W (2). Unscrew nut (3) and remove cable G1.D+ (4).

3 4

39560 0
11/2004

1/12

0312 1633 - 0138

Electrical system W 13-02-03

Unclip cable plug (1).

2011

1
39561 0

Unscrew screws (1) and remove cable holders (arrows).

39611 0

Unscrew screws (1) and remove cooler blower with generator.

1
39562 0
11/2004

2/12

0312 1633 - 0138

2011
Remove generator from cooling blower Unscrew screws (arrows) and remove blower jacket inlet (1).

Electrical system W 13-02-03

39565 0

Unscrew nut (1).

6
1

Note
Hold shaft.

39566 0

Remove disc (1), V-belt pulley (2) and running wheel (3).

39567 0
11/2004

3/12

0312 1633 - 0138

Electrical system W 13-02-03

Remove spacer disc (1).

2011

39568 0

Remove guide disc (1).

39569 0

Unscrew nut (2) and press out rubber muff (1).

39570 0
11/2004

4/12

0312 1633 - 0138

2011
Unscrew nuts (1) and press out generator. Visually inspect components and renew if necessary.

Electrical system W 13-02-03

39571 0

Install generator in cooling blower Insert generator and press in to stop.

Note
Note installation position of the generator.

39572 0

Mount washers and tighten nuts (1) alternately.

Note
Check the installation position again.

1
09065

39571 0
11/2004

5/12

0312 1633 - 0138

Electrical system W 13-02-03

Mount guide disc (1).

2011
1

Note
The stepped side (arrow) must face the generator.

39573 0

Mount spacer disc (1).

39574 0

Mount running wheel (3), V-belt pulley (2) and disc.

Note
Note installation position.

39567 0
11/2004

6/12

0312 1633 - 0138

2011
Tighten nut.
13021

Electrical system W 13-02-03

39575 0

Check gap dimension Press out the protective grille (1) carefully from the blower jacket inlet at the fastening points (arrows).

Note
Do not damage the protective grille!

39576 0

Mount blower jacket inlet (1) and tighten screws (2).

Note
Note the installation position, the gates (arrows) must be in line.

1
09067

2 2

39577 0
11/2004

7/12

0312 1633 - 0138

Electrical system W 13-02-03

Measure the gap dimension with a feeler gauge between the running wheel and the blower jacket inlet.
09 91

2011

39578 0

Compensate gap dimension with the appropriate spacer disc (1).

Note
Spacer discs of 5 to 7 mm are available.

39574 0

Press the protective grille (1) carefully into the blower jacket inlet.

Note
Observe the fastening points.

39579 0
11/2004

8/12

0312 1633 - 0138

2011
Insert rubber muff (1) and tighten nut (2).
13081

Electrical system W 13-02-03

39580 0

Install generator Mount cooler blower with generator and tighten screws.
09066

39564 0

Position cable holders (arrows) and tighten screws.

Note
Note different screw length: Screw M6 x 12 mm (1) Screw M8 x 20 mm (2) Tighten screw (1).
13092

Tighten screw (2).

13092

39271 0
11/2004

9/12

0312 1633 - 0138

Electrical system W 13-02-03

Clip in cable plug (1).

2011

1
39561 0

Plug cable to generator. Attach cable "G1.D+" (4) and tighten nut (3).
13082

Attach cable "G1.W" (2) and tighten nut (1).

13083

3 4

39560 0

Mount air duct cover (1).

Note
The air duct cover must be under the stand plate and the profile rubber (arrows).

39490 0
11/2004

10/12

0312 1633 - 0138

2011
Fix air duct cover (2). Tighten screws (1).
09087

Electrical system W 13-02-03

Install V-belt. Job card W 12-02-01.

1 1

39080 0

11/2004

11/12

0312 1633 - 0138

Electrical system W 13-02-03

Notes

2011

11/2004

12/12

0312 1633 - 0138

2011
W 13-02-03

Electrical system W 13-02-03

Remove and install generator and holder (in FM, BFM engines)
Tools
- Commercial tools 8189 - Torx tool kit

References
- W 12-02-01

Note
One variant has been described. The procedure is the same accordingly for other variants.

Remove generator Remove cable from generator if available. Item Item Item (1) (2) (3) D+ B+ W

Remove V-belt Job card W 12-02-01.

39445 0

Unscrew nut (arrow), remove screw (1) and washers.

1
39447 0
11/2004

1/6

0312 1634 - 0138

Electrical system W 13-02-03

Unscrew screw (1) and remove generator.

2011

39448 0

Unscrew screws (1) and remove console (2).

39449 0

Unscrew screw (1) and remove clamping bracket (2). Check components for visible signs of damage.

39446 0
11/2004

2/6

0312 1634 - 0138

2011
Install generator Mount clamping bracket (2) and tighten screw (1).

Electrical system W 13-02-03

Note
Note installation position of the clamping bracket.

39446 0

Mount console (2) and tighten screws (1).

13010

39449 0

Insert generator and tighten screw (1).

39448 0
11/2004

3/6

0312 1634 - 0138

Electrical system W 13-02-03

Insert screw (1) and washers, tighten nut (arrow). Install V-belt. Job card W 12-02-01.

2011

1
39447 0

Plug cable into generator if available. Item Item Item (1) (2) (3) D+ B+ W

39445 0

Console fastening with built-up fan drive (unit design) Tighten screws (1 and 2).
13010

Tighten screw (3).

13022

3 2

34288 1
11/2004

4/6

0312 1634 - 0138

2011
Console fastening with built-up fan drive (building machine design) Tighten screws (1).

Electrical system W 13-02-03

1
13010

Tighten screw (2).

13022

2 1

34291 1

11/2004

5/6

0312 1634 - 0138

Electrical system W 13-02-03

Notes

2011

11/2004

6/6

0312 1634 - 0138

2011
W 13-03-02

Electrical system W 13-03-02

Remove and install starter

Tools
- Commercial tools

Remove starter If available, remove the heat shield (1). Unscrew screws (2).

6
2

39380 0

Unscrew screw (1) and remove cable holder (2). Unscrew nut (3) and remove charging current cable (4).

2 4 3

39540 0
11/2004

1/4

0312 1635 - 0138

Electrical system W 13-03-02

Unscrew screws (1) and remove starter.

2011
1

39541 0

Insert starter and tighten screws (1).

13001

39542 0

Connect charging current cable (4) and tighten nut (3).

13071

Position cable holder (2) and tighten screw (1).

13092

2 4 3

39540 0
11/2004

2/4

0312 1635 - 0138

2011
If available, install the heat shield (1). Tighten screws (2).

Electrical system W 13-03-02

2
13009

39380 0

11/2004

3/4

0312 1635 - 0138

Electrical system W 13-03-02

Notes

2011

11/2004

4/4

0312 1635 - 0138

2011
W 13-06-01

Electrical system W 13-06-01

Remove and install helical heater plug

Tools
- Commercial tools

Remove helical heater plugs Unscrew helical heater plugs (1) and remove sealing rings. Check components for visible signs of damage.

39033 0

Install helical heater plugs Tighten helical heater plug (1) with new CU sealing ring.
13031

39035 0
11/2004

1/2

0312 1636 - 0138

Electrical system W 13-06-01

Notes

2011

11/2004

2/2

0312 1636 - 0138

2011

Commercial tools
7

Please send all tool orders directly to: WILBR Wilhelm Bcker GmbH & Co. KG Postfach 14 05 80 D -42826 Remscheid Fax: ++49 (0) 02191 - 8 10 92 Tel.: ++49 (0) 21191 - 9882-860 E-mail address for orders from Germany: [email protected] (Ms. Zarrath) other countries: a. [email protected] (Ms. Karsten)

11/2004

1/8

0312 1640 - 0138

7 Commercial tools 2011

Notes

11/2004

2/8

0312 1640 - 0138

7 Commercial tools 2011

8005 Compression tester for diesel engines 10-40 bar Set

8005

35410 2

8008

Nozzle tester with spray mist collector

7
2

8008

35411 2

8011

Clamping pliers for leak fuel lines

8011
11/2004

39426 0
0312 1640 - 0138

3/8

7 Commercial tools 2011

8018 Claw wrench Size 17 for union nuts of the injection lines, reinforced

8018

37506 1

8021

Socket size 15 long, hexagonal , for union nut injection valve

8021

39427 0

8024

Assembly pliers for valve shaft sealing, for removing the valve shaft seal

8024
11/2004

37509 1
0312 1640 - 0138

4/8

7 Commercial tools 2011

8027 Pliers insert for solenoid valve

8027

39531 0

8036

Socket size 32, set with 8049

7
2

8036

39429 0

8049

Force multiplier for center screw on the crankshaft, set with 8036

8049
11/2004

39430 0
0312 1640 - 0138

5/8

7 Commercial tools 2011

8112 Insert for screwdriver, 1/2" size 17

8112

39431 0

8115

V-belt pulley tension measuring appliance 150 to 600 N, test the V-belt pulley tension

8115

35416 2

8170

Depth measuring appliance

8170
11/2004

39532 0
0312 1640 - 0138

6/8

7 Commercial tools 2011

8189 Torx tool kit

8189

39432 0

9017

Assembly lever for valve spring

7
2

9017

37511 1

9088

Clamping pliers for hose clips, 220 mm, spring clamps

9088
11/2004

39433 0
0312 1640 - 0138

7/8

7 Commercial tools 2011

9090 Clamping pliers for hose clips, 320 mm, clamping spring clamps

9090

35420 2

9120

Special bit, 70 mm long IPR 30, 70 mm long, for secure screwing on regulator

9120

39434 0

9122

Special bit, 25 mm long IPR 30, 25mm long, for secure screwing on regulator

9122
11/2004

39435 0
0312 1640 - 0138

8/8

2011

Special tools
8

Please send all tool orders directly to: WILBR Wilhelm Bcker GmbH & Co. KG Postfach 14 05 80 D -42826 Remscheid Fax: ++49 (0) 02191 - 8 10 92 Tel.: ++49 (0) 21191 - 9882-860 E-mail address for orders from Germany: [email protected] (Ms. Zarrath) other countries: a. [email protected] (Ms. Karsten)

11/2004

1/16

0312 1641 - 0138

8 Special tools 2011

Notes

11/2004

2/16

0312 1641 - 0138

8 Special tools 2011

100 120 Connecting piece for compression tester

100 120

39400 0

100 400

Meter in connection with 100 750

8
4

100 400

37605 1

100 690

Marking pin for Bosch injection pump

100 690
11/2004

39368 0
0312 1641 - 0138

3/16

8 Special tools 2011

100 700 Setting bolt for toothed belt assembly Crankshaft and camshaft

100 700

39101 0

100.710

Setting bolt for control linkage

100 710

39401 0

100 750

Measuring device with shim discs for piston overhang and front cover in connection with 100 400

100 750
11/2004

39402 0
0312 1641 - 0138

4/16

8 Special tools 2011

100 880 Marking pin for Bosch injection pumps Wire length 64mm

Note
No longer available. Replaced by marking pin 100 690.

100 880

39403 0

101 100

Marking pin for Motorpal

8
2

101 100

39404 0

101 300

Pointer for degree scales

101 300
11/2004

39406 0
0312 1641 - 0138

5/16

8 Special tools 2011

101 500 Hand pump High pressure hand pump for testing and setting the static beginning of pumping

101 500

36443 1

101 510

Tank Supply tank for high pressure hand pump

101 510

36444 1

101 910

Device for reading the angle degrees

101 910
11/2004

36449 1
0312 1641 - 0138

6/16

8 Special tools 2011

103 030 Test template for compensation gasket of the injection pump

103 030

39533 0

110 030

Extractor for injection valve in connection with 150 800

8
2

35433 2

110 110

Holder for injection valve SW11 to accommodate the injection valve in the vice

110 110
11/2004

35431 2
0312 1641 - 0138

7/16

8 Special tools 2011

110 140 Assembly tool for control linkage bushes

110 140

39407 0

120 900

Clamping block for cylinder head, swivelling

120 900

35438 2

120 910

Clamping plate for clamping plate 120 900 if this is not screwed tight

120 910
11/2004

35439 2
0312 1641 - 0138

8/16

8 Special tools 2011

121 410 Assembly tool for valve shaft seals

121 410

37614 1

130 300

Universal piston ring pliers Disassemble and assemble piston rings

8
2

130 300

35441 2

130 420

Trapezoidal wear gauge

130 420
11/2004

36461 1
0312 1641 - 0138

9/16

8 Special tools 2011

130 630 Piston ring tensioning band

130 630

39408 0

131 100

Disassembly tool for piston bolt lock

131 100

39409 0

131 340

Assembly tool for FL/M engines for piston bolt bush of FL/M engines

131 340
11/2004

39410 0
0312 1641 - 0138

10/16

8 Special tools 2011

131 350 Assembly tool for BF/M engines for piston bolt bush of BF/M engines

131 350

39411 0

142 050

Press-in device for camshaft sealing ring

8
2

142 050

39412 0

142 850

Assembly tool for camshaft sealing ring without running ring, opposite side to flywheel

142 850
11/2004

39414 0
0312 1641 - 0138

11/16

8 Special tools 2011

142 860 Assembly tool for camshaft sealing ring without running ring, flywheel side

142 860

39415 0

143 100

Pressing device for flywheel

143 100

39416 0

143 420

Holder for force multiplier

143 420
11/2004

39417 0
0312 1641 - 0138

12/16

8 Special tools 2011

143 430 Intermediate disc for holder 143 420

143 430

39418 0

143 820

Assembly tool for camshaft bearing

8
2

143 820

39419 0

144 130

Holder for camshaft wheel

144 130
11/2004

39420 0
0312 1641 - 0138

13/16

8 Special tools 2011

150 140 Extraction tool for oil pipe in crankcase

150 140

39421 0

150 150

Assembly pin for oil pipe in crankcase

150 150

39422 0

150 800

Extraction tool e.g. for injection valves

35449 2
11/2004

14/16

0312 1641 - 0138

8 Special tools 2011

170 050 Special wrench for filter cartridge, for unscrewing the filter cartridge

170 050

37629 1

170 110

Special wrench for oil pressure sensor

8
2

170 110

39423 0

6067

Engine assembly stand

6067
11/2004

39424 0
0312 1641 - 0138

15/16

8 Special tools 2011

6067/114 Support arm

6067/114

39369 0

6067/115

Clamping holder

6067/115

39425 0

11/2004

16/16

0312 1641 - 0138