Scribd
Upload
19 views11 pages

Unconventional Machining

This document introduces and summarizes several non-traditional machining processes including ultrasonic machining, abrasive water jet machining, chemical machining, electro-chemical machining, electro-chemical grinding, electrodischarge machining, and laser beam machining. It provides brief descriptions of how each process works by removing material using techniques such as abrasive slurry, high pressure water jets, controlled chemical or electrochemical dissolution, electric sparking, or high intensity laser beams. Standard grinding and its wheel designations are also briefly covered.

Uploaded by

Saravanan Mathi
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
19 views11 pages

Unconventional Machining

This document introduces and summarizes several non-traditional machining processes including ultrasonic machining, abrasive water jet machining, chemical machining, electro-chemical machining, electro-chemical grinding, electrodischarge machining, and laser beam machining. It provides brief descriptions of how each process works by removing material using techniques such as abrasive slurry, high pressure water jets, controlled chemical or electrochemical dissolution, electric sparking, or high intensity laser beams. Standard grinding and its wheel designations are also briefly covered.

Uploaded by

Saravanan Mathi
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 11

INTRODUCTION

Abrasive Grinding

Non-traditional Machining Processes


Ultrasonic Machining Abrasive Water Jet Machining Chemical Machining Electro-chemical Machining

Electro-chemical Grinding
Electrodischarge Machining Laser Beam Machining Case Studies Overall Process comparisons .

Abrasive Grinding

Can be viewed as multiple very small cutting edges Results in a very fine finish Can leave residual stresses Slow, small material removal rates Sparking out

Standard Grinding Wheel Designation While this is specific to grinding, realize that there are similar standard designations in most industries Take the time to learn the standard designations early so that you can speak intelligibly with those within the industry.

INTRODUCTION

Ultrasonic vibration (20,000 Hz) of very small amplitudes (0.04-0.08 mm) drive the form tool (sonotrode) of ductile material (usually soft steel) An abrasive slurry is flowed through the work area The workpiece is brittle in nature (i.e. glass) The workpiece is gradually eroded away.

Abrasive Water jet (AWJ) Cutting

Abrasive Water jet (AWJ) Cutting

INTRODUCTION

High pressure water (20,000-60,000 psi)

Educt abrasive into stream


Can cut extremely thick parts (5-10

inches possible)
Thickness achievable is a function of speed Twice as thick will take more than twice as long

Tight tolerances achievable

Current machines 0.002 (older machines much less capable ~ 0.010

Jet will lag machine position, so controls must plan for it


.

Chemical Machining Applications:


Aerospace industry Engraving Circuit boards

A maskant is applied over areas you dont want to machine


Photochemical methods Apply maskant to entire surface and use laser to cut

Place the entire part in a chemical bath (acid or alkali depending upon the metal) Control temperature and time of exposure to control material removal
.

Electro-Chemical Machining (ECM)

Works on the principle of electrolysis accelerated chemilling

Die is progressively lowered into workpiece as workpiece is dissociated into ions by electrolysis
Electrolytic fluid flows around workpiece to remove ions and maintain electrical current path Low DC voltage, very High current (700 amps)

Electrode Discharge Machining (EDM)

Direct Competitor of ECM much more common than ECM The tool acts as a cathode (typically graphite) is immersed in a Dielectric fluid with conductive workpiece DC voltage (~300V) is applied. As voltage builds up over gap between workpiece and tool, eventually you get dielectric breakdown (sparking at around 12,000 deg F) The sparking erodes the workpiece in the shape of the tool The tool is progressively lowered by CNC as the workpiece erodes Cycle is repeated at 200,000-500,000 Hz Dielectric:
Cools tool and workpiece Flushes out debris from work area

Laser Beam Machining

Lasers are high intensity focused light sources


CO2
Most widely used Generally more powerful that YAG lasers Cutting operations commonly Less powerful Etching/marking type operations more commonly

Nd : YAG (Neodymium ions in an Yttrium Aluminum Garnet)


Limited in depth of cut (focus of light) Would limit work piece to less than 1 inch (< typically)

You might also like