iVA

m/ir
-^imnriMifiBiaitllniSH
*, .*
'-'>.
Gop>iightN!'.
CiiPW?IGHT DEPOSIT.
Agricultural Woodworking
A GROUP OF PROBLEMS FOR
Rural and Graded Schools, Agricultural High Schools
and the Farm Workshop
By
Louis M. Roehl
u
Director of Farm Mechanics,
Milwaukee County School of Agriculture
and Domestic Economy,
Wauwatosa, Wisconsin
The Bruce Publishing Company
MILWAUKEE, WIS.
Copyright 1916
The Bruce PubHshing Company
ft
AUG 31 1916
17-/^^^/
iCI.A4^H332
PREFACE
THE
manual training which is offered in the rural schools,
graded schools and agricultural high schools should
be principally of an agricultural nature. Work of this
kind has a tendency to keep the boys in school for a longer
period of time. It creates a desire to use tools in making
farm necessities and improving farm buildings and equipment.
It develops a closer relationship between the school and the
home. It trains the eye and hand and develops patience,
perseverance, judgment and accuracy. It creates a desire
to equip and use a shop at home. It has a bearing on mak-
ing the boys want to stay on the farm.
It is with these thoughts in mind that this book on
agricultural woodworking has been prepared. It is intended
that it be used by the boys both at school and at home in
the farm workshop as an aid to efficient farming.
CONTENTS
Page
Preface
3
Woodworking Equipment for Country
Schools 5
Directions for Reducing Stock to
Dimensions
6-7
Bread Board
8-9
Bench Hook
10-11
Feeding Trough for Clucks
12-13
Fly Trap
14-15
Folding Bench
16-17
Nail and Staple Box
18-19
Bird House
20-21
Window Screen
22-23
Tool Sharpening 24
Saw Filing 25
Milking Stool
26-27
Ironing Board
28-29
Wagon Jack 30-31
Conuuunity liird House 32-33
Chicken Feonl Hopper 34-35
Chicken Brooder Coop and Bun 36-37
Eveners and Singletree
38-39
Fence and Gate
40-41
Bench
42-43
Rabbit Trap
44-45
Seed Corn Ciu'ing Frame 46-47
Seed Corn Tree. . . ;
46-48
Chicken Brooder Coop and Run
49-50-51
Clothes Line Reel and Kitchen Stool. . .52-53
Step Ladder 54-55
Swinging Farm Gate 56-57
Trap Nest
58-59
Hive Seat and Tool Box 60-61
Ladders 62-63
Carpenter's Tool Box 64-65
Two-Man Weight Carrier 66-67
Saw Horse 68-69
Page
Lawn or Porch Seat. . 70-71
Daily Milk Record Sheet Case 72-73-74
Oats Sprouter 75-76-77
Fruit Ladder 78-79
Wagon Box 80-81
Flat Hay Rack 82-83
Carpenter's Work Bench 84-85-86
A Farm Work Shop 87-91
Ensilage Rack 92-93
Roughage Feed Rack for Swine 94-95
Roughage Feed Rack for Cattle 96-97
Hay Rack 98-99
King Road Drag 100-101
Grain Bed 102-103
Garden Wheelbarrow 104
Land Leveler 105
Blanker 106
Wagon Bed 107
Wagon Box 108
Toi)
Wagon Box 109
Stock Rack 110
Silo Form 111-112
Farm Buildings 113
Portable Hog House 114
Colony Poultry House 115-116
Poultry House 117
Pigeon House 118
Hog House 119
Implement Shed 120
(^orn C'ril) 121
Combination Dairy and Horse Barn. 122-125
(combination Horse and Cow Barn 126
Plan for a Farmstead 127
Knots and Sphces
128-133
Lacing a Belt with a Rawhide Thong .... 134
Lacing a Belt with Metallic Wire Belt
Lacing - 135
Tools
136-137
WOODWORKING EQUIPMENT FOR
COUNTRY SCHOOLS
-22-inch Hand Rip Saw 8 Point
$1 .50
-22-inch Hand Cross Cut Saw 8 Point 1 . 50
-Claw Hammer, 12 oz. Straight Claw, Plain Face . .55
-Jack Plane, 14-inch with 2-inch Cutter 2. 15
-Try Square, 8 inch
.35
-T bevel, 8 inch
30
-Marking Gauge No. 10
-Divider, 8 inch
.35
-Carpenter's Mallet,
2fx3f
inches .25
-2-foot Four Fold Rule, Brass Bound
35
-j-inch Socket Firmer Chisel .35
-|-inch Socket Firmer Chisel
.35
-f
-inch Socket Firmer Chisel
.40
-Bench Stops .10
-8-inch Bench Brush .35
-12-inch Handy Saw 1 . 25
-Steel Rafter Framing Square 1.75
-Bench Hook 35
-6-inch Screw Driver .30
-10-inch Screw Driver .50
-Ratchet Brace, 8-inch Sweep 1 . 10
-10-inch Flat Bastard Mill File, with Handle 25
-6-inch Slim Taper Triangular File, with Handle... . 10
-8-inch Drawing Knife .70
-Nail Set, 3-32 inch 10
-Rose Countersink .15
-Set Twist Drill Bits 1 . 25
-2x8-inch Combination Carborundum Stone 1 . 00
-Special Saw Set .40
-6-inch Combination Plier .30
-Putty Knife 15
-Set of Six Auger Bits,
I, f, ^, f, f
, 1 inch 1 .50
-Coping Saw, Nickel Plated, Wire Frame .25
$20.35
For illustrations of tools see pages 136-137.
AGRICULTURAL WOODWORKING
DIRECTIONS FOR REDUCING STOCK TO DIMENSIONS
1
Plane one side smooth and
mark "I." Call this side the
working face. Fig. 1.
Fig. 1. Holding Wood Between Beneli i'eg
Planing Surface.
-Plane one adjoining edge
at right angles to surface "I"
and mark "II." Call this
edge the working edge.
Fig. 2.
Fig. 2. Edge Planing.
3
Draw a line acro.ss surface
"I" near one end at right
angles to surface "II," and
remove the end stock to
line with saw or plane.
Mark end surface "III."
Call this end the working
end. Kig. 3,
Fig. 4.
Fig. 3. Squaring the End with Try Square
and Pencil.
AGRICULTURAL WOODWORKING
-Measure off the length of the
required piece on surface
"I" from the end surface
"III," and reduce stock to
length with saw or plane.
Fig. 4.
Fig. 4a. End Planing with a Block Plane.
5
Mea.sure off the width of the
required piece on surface "I"
from edge "II" and remove
stock to line with plane.
6
With marking gauge set at
the thickness of the required
piece, measure off the thick-
ness of the required stock
from surface "I" and remove
stock to line with plane.
Fig. 5.
Sawing Cross Grain on Bench Hook with
Back or Handy Saw.
4aThe end may be trimmed
with a block plane as shown.
Fig. 4a.
Fig. 5. The Marking Gauge in Use.
-
In reducing a piece of
wood to dimensions the try
square should be used con-
stantly, to obtain right angles
with the adjoining surfaces.
The stock should be removed
to the line but the line should
never be cut away. Fig. 6.
Fig. 6. Testing to See if End is Square
with the Edge.
AGRICULTURAL WOODWORKING
BREAD BOARD
Material Required
Lumber : 1 piece basswood, pop-
lar or white pine tlx5^xllK
inches.
Tools
Sharp lead pencil, rule, try
square, jack plane, handy
saw, brace,
^g
inch bit,
^
inch chisel, marking gauge,
dividers.
Stock Bill
Pieces. Finished Dimensions.
1. ^x53^x11 inches.
Fig. 7. Swinging an Arc with a Compass.
Directions
-Reduce stock to finished di-
mensions following the above
directions.
-To lay out round corners
locate points at each corner
on both sides 1 inch from
end and 1 inch from edge,
and with dividers set at a
1-
inch radius swing an arc
across the corner to edge
and end. Fig. 7.
Fig. 8. Chiseling with the Grain.
3
Draw a Hne across edge and
end at each corner 1 inch
from the corner so that the
proper amount of stock may
be removed.
4
Remove stock at corner with
%
inch chisel, cutting with
the grain. Fig. 8.
Fig. 9. Boring a Hole.
-Locate a point
%
inch from
one end on a center line
drawn lengthwise of the
stock and bore hole with
^8
inch bit. Bore from one
side until the point of the
bit comes through, then turn
the board and finish from the
other side. This prevents
sphtting of the wood around
the hole. Fig. 9, Fig. 10.
Fig. 10. Feeling for the Point of the Bit.
10
AGRICULTURAL
WOODWORKING 11
BENCH HOOK
Material Required
Lumber: 1 piece white or yellow pine,
^x5ysxl0y2 inches.
1 piece white or yellow pine
T^xlJ^xll inches.
(Cypress or Oregon pine may
be substituted for white or yel-
low pine.)
Hardware : 6 flat head bright wood screws
l^inch, No. 8.
Fig. 12. Setting a Plane.
Directions
1
Reduce all pieces to finished dimensions.
2
Draw a center line lengthwise of big piece.
3
Locate a point on line just drawn
214
inches from one end and bore % inch hole.
4
Locate points on each of the small pieces
for screws.
5
Bore holes for screws with ^ inch twist
bit and countersink the holes.
6
Clamp all pieces accurately in position in
vise and assemble with screws. If white
pine or other soft wood is used the screws
may be forced into the large piece without
drilling a hole, but if yellow pine or other
hardwood is used a hole should be made for
starting the screw with a smaller bit than
that used for the shank of the screw.
The screw driver should be held straight
and pressed firmly so as not to mar the slot
in the screw.
The hole for the-ljead of the screw should
be countersunk so that the head is slightly
below the surface of the wood.
Fig. 11. Position to Hold Sand Paper and 8aud
Paper Block.
Tools
Sharp lead pencil, rule, try square, jack plane,
handy saw, brace, ^
inch bit. No. A inch
twist drill, countersink, screw driver.
Stock Bill
Pieces. Finished Dimensions.
1. Mx53^xlO in.
1. Mxl^x
5M
in.
1. HxlHx 43^
in.
Fig. 13. Countersinking a Hole.
12
AGRICULTURAL WOODWORKING 13
FEEDING TROUGH FOR CHICKS
Material Required
Lumber: 1 piece cypress, white pine or
basswood, tlxdJ^^xQ
inches.
1 piece cypress, white pine or basswood,
T|xtix223^
inches.
1 piece cypress, white pine or basswood,
J^x9x30 inches.
(Poplar or redwood may be substituted
for cypress, white pine or basswood.)
Hardware: 2 flat head bright wood screws,
1>^
inch No. 10.
5 dozen
J^
inch brads.
16
1J4
inch brads.
12 4d finishing nails.
Tools
Sharp lead pencil, rule, try square, T bevel,
jack plane, hammer, brace, -^ inch twist
drill, countersink, nail set, screw driver.
Fig. 14. Proper Position to Hold Screw Driver
Pieces.
2.
1.
1.
2.
28.
Stock Bill
Finished Dimensions.
^x4 x4 inches.
%x %x22 inches.
3^x3 x22 inches.
Hx2^x22 inches.
Hx ^x 2'}4 inches.
Use.
Ends.
Ridge.
Bottom.
Sides.
Partitions.
Directions
1
Reduce all pieces to finished di-
mensions.
2
To make the end cuts of the par-
titions hold the saw at
45
to a
right angle.
3
Fasten ends to ridge with
13^ inch
No. 10 screw. Use
re
inch twist
drill for screw hole and counter-
sink hole.
4
Fasten ends to sides and bottom
with six 4d finishing nails at each
end.
5
Nail sides to bottom with
IJ^
inch brads. Use eight brads at
each side spaced evenly.
6
Fasten partitions by using one
]/s
inch brad at each end.
Fig. 15. Ripsawing on a Saw Horse.
14
AGklCULTURAL WOODWORKING 15
FLY TRAP
Material Required
Lumber: 1 piece white pine, cypress or basswoood t|x8x24 inches.
1 piece white pine or basswood J^xlKxSG inches.
Hardware: 16 fiat head bright wood screws IK
inch, No. 8.
4 dozen carpet tacks.
1 piece wire fly screen 14 inches square.
16 brads 1 34
inch, No. 18.
14 shingle nails.
Tools
Sharp lead pencil, rule, try square, jack
plane, handy saw, brace and ^ inch twist
drill, countersink, screw driver, hammer, nail
set, compass.
16
AGRICULTURAL WOODWORKING 17
FOLDING BENCH
Material Required
Lumber : 1 piece cypress or white pine
texS
inches x 9 ft. 6 inches.
1 piece cypress or white pine
HxlM
inches x 7 feet.
(Oregon pine or Southern pine may be substituted for cypress or white pine.)
Hardware: 30 flat head bright wood screws 1% inches, No. 10.
16 fiat head bright wood screws 1 inch, No. 7.
4 carriage bolts and washers
Hx2
inches.
Tools
Sharp lead pencil, rule, try square, jack plane, handy saw, brace,
%
inch bit,
rt
inch and
3^
inch twist drills, countersink,
%
inch chisel, rip saw, screw driver, pliers, dividers.
Pieces
2.
2.
2.
4.
2.
2.
4.
Stock Bill
Finished Dimensions.
Mx2Hx
4 feet
Mx2Hx
3 feet
Hx2}4xU}i
inches.
^x2 x21 inches.
^x2 xl6 inches,
^x ^xl43^ inches.
3^x1 x21 inches.
inches.
103^ inches.
Use.
Sides.
Platform.
Ends.
Legs.
End cross pieces.
Lower cross pieces.
End braces.
Directions
1Reduce all pieces to finished dimensions.
2
Fasten ends to four long pieces by using two 1% inch No. 10 screws at each joint. Bore
holes for screws with
re
inch twist bit and countersink holes.
3
Fasten end lower cross piece by placing five screws as shown in the drawing.
4
Locate points for bolts on side pieces 13/8 inches from top edge and 3^ inches from end
and bore hole with
^g
inch bit.
5
Round upper end of legs.
6
Bore
^-s
inch holes in legs at end for bolts.
7
Cut notch
3
inch deep and
%
inch wide in upper edge of legs 2 inches from end and fasten
cross piece in place with one 1% inch screw at each joint.
8
Lay out cross braces, making half lap joint at center and fasten with two 1 inch No. 7
screws at each joint, and one
^
inch screw at half lap joint.
9
Fasten legs to top with bolts.
18
AGRICULTURAL WOODWORKING 19
NAIL AND STAPLE BOX
Material Required
Lumber: 1 piece white pine or basswood i6x8KxllJ/2 inches.
1 piece white pine or basswood tix53^xll3^ inches.
1 piece white pine or basswood 3^x4 inches by 4 feet 2 inches.
(Redwood, poplar or cypress may be substituted for white pine or basswood.)
Hardware: 5 flat head bright wood screws l}i inches, No. 8.
3 dozen 4d finishing nails.
Tools
Sharp lead
pencil, rule, try square, jack plane, handy saw, brace and 5-32 inch twist drill,
countersink,
1 inch bit, screw driver, hammer,
%
inch chisel.
Fig. 17. Holdiug the Plane at au Angle tu Cut a Chamfer
Pieces.
1.
1.
2.
2.
2.
Stock Bill
Finished Dimensions.
^x8 xll inches.
^x53^x11 inches.
3/^x4 xl2 inches.
3^x4 X 8 inches.
3^x3
Mx
SYs
inches.
Use.
Bottom.
Partition and handle.
Sides.
Ends.
Cross partitions.
Directions
1 Reduce all pieces to finished dimensions.
2To lay out opening for hand draw a line lengthwise of stock 13^2
inches from upper edge,
also draw a center Hne crosswise of stock. Measurements should be made on hne running
lengthwise of stock from center line. Locate points on line 13^
inches from center hne
and bore 1 inch holes. Remove as much as possible of the remaining stock with 1
inch
bit and trim opening with
^
inch chisel.
3
In making partition and handle first reduce piece to %x534xll inches. To lay out the
slant draw two lines across upper edge
33^
inches from ends and a line across each end
2 inches from upper edge. Connect lines just drawn with hues on both sides.
4
Lay out
}i
inch chamfer on upper edge and both ends of opening with pencil and re-
move stock with chisel.
5
Remove stock for slant with saw and trim to line wath plane.
6
Lay out
3^
inch chamfer on corners of upper edge and remove stock with plane.
7
Assemble box by placing nails and screws as shown in drawing.
20
AGRICULTURAL WOODWORKING
21
BIRD HOUSE
Material Required
Lumber: 1 piece white pine or basswood %x5}4 inches x 3 feet 2 inches.
1 piece white pine or basswood Hx8Mx8H
inches.
1 piece white pine or basswood j^xl^xlQj^ inches.
(Poplar, cypress or redwood may be substituted for pine or basswood.)
Hardware: 1 flat head bright wood screw 2 inch No. 12.
4 flat head bright wood screws
J^
inch No. 7.
1 dozen IJ^
inch brads No. 18.
2 dozen 1 inch brads No. 18.
Tools
Sharp lead pencil, rule, try square, jack plane, handy saw, brace, coping saw, twist drills
7-32 inch and
3^
inch, countersink, screw driver, hammer, nail set, T bevel.
Pieces
1.
2.
2.
2.
1.
1.
Stock Bill
Finished Dimensions.
3^x6 3^x 8 inches.
^x5 X
5J4
inches.
Hx43/^x 4 inches.
^x4%x 8 inches.
3^x1 Hx
2 inches.
%xl xl6 inches.
Directions
Use.
Bottom.
Ends.
Sides.
Roof.
Brace.
Post.
circle.
1
Reduce all pieces to finished dimen.sions.
2
To make doorway draw a center line lengthwise of end piece and swing a circle with com-
pass using point on center line IJ^
inches from end as center.
3
Draw L'nes at right angle to end tangent to sides of circle.
4
Remove stock for doorway using handy saw to cut to circle and coping saw to make the
5
Set the T bevel at the same angle as
shown in the drawing and lay out the
slant for the gable of end pieces.
6
With T bevel in same position as for
gables lay out bevels on upper edge
of both sides and both edges of two
pieces for roof.
7

^Fasten brace to post with 2 inch No.

12 screw. Holes for flat head screws
should always be bored and counter-
sunk.
8
Fasten brace and post to bottom with
four ]/8
inch No. 7 screws as shown
in drawing.
9
Nail ends to sides by using three 1
inch brads at each joint.
10
Draw lines on lower side of bottom
piece where brads are to be placed
so that when driven through bottom
they will enter sides and ends.
11Nail bottom, ends and sides by us-
ing three 1 inch brads at each side
and back and two at front.
12Fasten top in place by using seven
1 inch brads for each side.
13
Set brads with nail set.
l-itr. is. Setting Xail with Nail Set.
22
AGRICULTURAL WOODWORKING 23
WINDOW SCREEN
Material Required for Each Window
Lumber: 1 piece white pine or cypress IH^'Z}^ inches by width of window for bottom rail.
1 piece white pine 1)^8x2 inches by width of window plus twice the length of win-
dow for top rails and stiles.
1 piece white pine IJsxl inch by width of window for middle rail.
Enough screen moulding to cover edges of screen and middle rail.
Hardware: Twenty lOd casing nails,
if nailed joint is used; 1 package No.
16 brads if mortise and tenon joint
is used and for nailing moulding;
package of carpet tacks for screen;
wire fly screen; paint.
The finished dimensions are not given
here as they must be obtained by measur-
ing the window where the screen is to fit.
The mortise and tenon joint is the
stronger and better way of joining the
screen at the corners, yet a nailed joint
holds the members firmly in place if the
Fig. 19. Position of Chisel and Mallet for Mortising.
nails are well placed at an angle as shown
in the drawing. The screen need lap
only far enough on the sides and ends to
be securely nailed. It should not project
outside of the moulding which is placed
on the inside edge of the sides and ends
and across the middle rail.
The painting should be done carefully
so as to prevent moisture from getting
into the joints.
Fig. 20. Method for Holding Chisel in Mortising.
24
AGRICULTURAL WOODWORKING
TOOL SHARPENING
There are three distinct operations in sharpening a plane bit or chisel; first, grinding,
Fig. 21; second, whetting the beveled side, Fig. 22; third, removing the wire edge from the
plain side, Fig. 23.
In grinding a plane iron loosen the cap screw with a screw driver and set the lever cap
back on the plane iron so that it will be out of the way when removing the wire edge from
the plain side.
The plane iron or cutter should
be held on the grinder so that the
edge will be a perfect right angle
with the side. It should be held
firmly in one position so that only
one bevel will be formed. In
grinding, the tool should be moved
from side to side on the grinder
so as to prevent wearing the stone
unevenly.
Fig. 21. Grinding a Chisel.
In whetting the beveled side of the
chisel or plane iron it should be held
firmly in both hands as indicated in
Fig. 22 and given three or four for-
ward strokes, pressing the iron firmly
on to the stone. Do not move the
wrists for this motion. The movement
should occur at the elbow and by the
swaying of the body forward and back.
Fig. 22. Whetting the Beveled Side of a Chisel.
licnidviiii; thr Wire Edge from the I hi
Side of a Chisel.
To remove the wire edge, lay the
flat side of chisel or plane iron, flat
on the oil stone as shown in Fig. 23
and move it back and forth three or
four strokes. Under no circumstances
should the end of the iron be raised
or lowered so that it won't lie flat
on the stone.
Until one becomes thoroughly famil-
iar with tool sharpening the whett ing of
both
beveled and plain sides may
need to be done more than once to
instu-e a good cutting tool.
AGRICULTURAL WOODWORKING 25
SAW FILING
The first operation in sharpening a saw is that of jointing the saw, Fig. 24. The purpose
of this is to bring'all teeth to an even length. This is done by drawing a flat file across the
teeth of the saw\ One or two strokes is usually sufficient. The file must be held perfectly
square; this may be facilitated by use of a block called a saw jointer, as shown in Fig. 24.
The second opera-
tion in saw sharpening
is that of setting the
saw. This consists of
bending the teeth out-
ward, one on one side,
the next on the other
and so on till all the
teeth are bent. The
set should not extend
more than half the
length of the tooth.
For ordinary work the
teeth should be set
about one-third the
thickness of the blade.
For dry lumber the
saw will require less
set than for green or
wet lumber.
The third operation is that of filing the saw. In fifing a cross-cut saw the point of the
file should point toward the point of the saw at an angle of about 45 degrees. In filing a
rip saw the file is held straight across the saw. File every tooth to a point, one-half of
the fiUng being done from each
side, being careful to stop filing
a tooth when it has been brought
to a point. File the entire
length of the saw from one side,
then reverse the saw and file
from the^other^side. The front
edge of each tooth projecting
away from the filer and the back
edge of the tooth next ahead,
should be filed with the same
stroke. Only forward strokes
i)f the file should be used.
The fourth operation con-
sists of placing the saw flat on
a smooth surface, as the top of
a bench, and running a whet-
stone over the teeth so as to re-
move the burr from the teeth
Fig. 25. Filing a Saw.
caused by filing.
Fig. 24. Jointing a Saw.
26
AGRICULTURAL WOODWORKING 27
MILKING STOOL
Material Required
Lumber: 1 piece white pine i^"xl0"x5'
3".
(Cypress or redwood may be substituted for white pine.)
Hardware: 15 flat head bright wood screws,
If"
No. 10. 16 flat head
bright wood screws,
If"
No. 8 for braces.
28
AGRICULTURAL WOODWORKING
29
IRONING BOARD
Material Required
Lumber: 1 piece white pine, poplar or basswood,
I|"xl2"x5'
0".
1 piece white pine, poplar or basswood, il"x4"x3'
6".
1 piece birch or oak tixl|"x8'
4".
Hardware: 2 carriage bolts \"x2^" with 2 washers each.
4 flat head bright wood screws 1\", No. 8.
2 flat head bright wood screws |", No. 7.
2 steel butt hinges, riveted, with 1\" screws.
Stock Bill
Pieces. Finished Dimensions Use.
1.
Ii"xl2"x5'
0"
Board.
2. ir'xU"x3'
2"
Clamps.
1. fr'xl"xl2"
Parting Strip.
1. |"xl"x9i"
Cross bar.
1. il"x4"x2'
7"
Post.
1. il"x4"xl0"
Post and Hinge
Support.
Directions
1. Reduce all pieces to finished dimensions.
2. To shape the board draw a center line lengthwise of stock and swing
an arc with
5"
radius on center line
5"
from end.
3. Draw lines across both edges
2' 3"
from the same end as the arc.
4. Remove stock to line with saw, draw knife and plane.
5. Locate points for bolts
4"
from end and
2"
from edge and bore a
11-16"
hole
Y'
deep on the upper edge of board.
6. Bore
\"
holes thru the board in center of
11-16"
holes, and thru the
parting strips and clamps.
7. Bolt these three members in place and plug the
11-16" holes.
8. Fasten the post to the post and hinge support with four l\" No. 8
screws.
9. Cut a small groove in the lower side of the board and also in the
edge of the post and hinge support for the joint of the hinges and fasten the
hinges.
10. Place the board on the bench and the post standing up at right
angle to the board and fasten the cross bar to the clamps so that it touches
the post.
11. Bore the
f"
hole in the lower end of post for hanging the board.
30
AGRICULTURAL WOODWORKING 31
WAGON JACK
Material Required
Lumber : 1 piece oak, birch, maple or other hardwood I"x6"x6'
6".
Hardware: 6 machine bolts |"x3|" with washers.
2 flat head, bright wood screws 1|", No. 10.
2 pieces of iron
i"xl"x4".
3 iron rivets V'xll".
^^-LV_"
I
b-II-
T7>e
-J I
-H
i
I
I I
173-5
32
AGRICULTURAL WOODWORKING 33
COMMUNITY BIRD HOUSE
Material Required
Lumber: 1 piece white pine or basswood ^"x6|"x9'
4".
1 piece white pine or basswood Ti"x4"x4".
1 piece white pine or basswood l|"xl^"xl6".
(Poplar, cypress or redwood may be substituted for white pine or
basswood.)
Hardware: 1 flat head bright wood screw 2^', No. 12.
4 flat head bright wood screws \\", No. 8.
2| doz. brads 1\", No. 18, for bottom and sides.
1| doz. 6d finishing nails for roof.
-><?-
I
^t
34
36
AGRICULTURAL WOODWORKING 37
Lumber
:
Hardware
:
CHICKEN BROODER COOP AND RUN
Material Required
1 piece t|"x9"x10'
0"
white pine, Oregon pine, cypress or redwood.
1 piece ii"x23^"xlO'
0"
white pine, Oregon pine, cypress or redwood.
1 piece t|"x2"x7'
6"
white pine, Oregon pme, cypress or redwood.
1 piece -i|"xl3^"x2'
0"
white pine, Oregon pine, cypress or redwood.
1 piece j^"xl"x2'
0"
white pine, Oregon pine, cypress or redwood.
^
lb. 4d common nails.
1 lb. 6d common nails.
21 hneal ft. 18",
1"
mesh chicken wire.
34
lb. ^"poultry netting staples.
38
AGRICULTURAL WOODWORKING 39
THREE-HORSE EVENER
Lumber: 1 piece select hickory I|"x5"x4'
4".
(If hickory is not avail-
able, white ash may be used.)
Hardware: 1 iron rivet j"x3|" with 2 washers.
1 iron rivet
l"x5l"
with 2 washers.
Directions
1. Reduce stock to If"x5"x4'
4".
2. Lay out the taper for the one-horse end by drawing a line from a
point on the back edge of the stock
21"
from the two-horse end to a point on
the one-horse end 3^" from the front edge.
3. Remove the stock to line with saw and plane.
4. Lay out and cut a
I"
chamfer on the edges of the stock as indicated
in the drawing.
5. Bore
I"
holes for the rivets 1|" from ends and fasten rivets by
securely riveting them.
6. Locate points
2"
from ends and 1|" from back edge of stock and bore
f
" holes for clevises.
7. Locate a point
18"
from the two-horse end and
1|"
from the front
edge, and bore a
f
" hole for main clevis pin.
TWO-HORSE EVENER
Lumber: 1 piece select hickory or ash If"x4^"x4'
0".
Hardware: 2 iron rivets
j"x3f".
Directions
1. Reduce stock to If"x4|"x4'
0".
2. Lay out the taper by drawing lines across the back edge of the stock
21"
from each end and lines across both ends 3^" from the front edge and con-
necting the lines by lines drawn on the sides of the stock.
3. Remove the stock to line with the saw and plane.
4. Lay out and cut a
j"
chamfer on the edges of the stock as indicated
in the drawing.
5. Bore
|"
holes for the rivets Ij" from ends and place rivets.
6. Locate points
2"
from ends and 1|" from back edge of stock and
bore
9-16"
holes for clevises.
7. Locate a point
24"
from either end and
1|"
from the front edge and
bore a
f
" hole for the main clevis pin.
SINGLETREE
Lumber: 1 piece of hickory or ash 2i"x2f"x2'
10".
Directions
1. Square up the stock to finished dimensions.
2. Find the center at each end by drawing lines diagonally as shown
in the detail drawing.
3. Draw a circle at center of each end
1|"
in diameter.
4. Cut a templet of pasteboard as shown in the detail drawing and
use in getting the singletree a perfect oval at the center.
5. In removing the stock, bring it to a square at the end, then an octagon
and then a circle. Remove the bulk of the stock with the saw and finish with
the plane. The singletree may be sanded to produce a smooth finish.
40
AGRICULTURAL WOODWORKING 41
FENCE AND GATE
Material Required
Lumber: 5 pieces white or yellow pine |"x6"xl6'
0".
2 pieces white or yellow pine |"x6"xl4'
0".
1 piece white or yellow pine |"x4"x6'
0".
1 piece round hardwood
f
"x6".
(Oregon pine or cypress may be substituted for white or yellow pine.)
Hardware : 2 pair screw hook and strap hinges.
26 carriage bolts
f
"x3".
16 carriage bolts
f"x2".
23 6d common nails.
42
AGRICULTURAL WOODWORKING 43
BENCH.
Material Required.
Lumber1 piece white pine 13/16"xl2"x3'
0"
1 piece white pine 13/16"x4"xl2'
0"
1 piece white pine 13/16"x7"xl0'
0"
Hardware12 flat head bright wood screws Ij" No. 8
16 flat head bright wood screws
If"
No. 10
Stock Bill.
Pieces Finished Dimensions Use
2 13/16"xl2"xl7" Legs
2 13/16"x4''xl0f
"
Cross braces
2 13/16"x4"x4'
8"
Aprons
2 13/16"x7"x5'
0"
Top
Directions.
1. Reduce all pieces to finished d'mensions.
2. Lay out the opening at the lower end of the legs and remove the
stock with the rip saw and coping saw.
3. Cut the openings for the aprons on each edge at the upper end of
the legs.
4. Bore holes with No. 5 wood twist drill and fasten the cross braces
with five flat head bright wood screws Ij" No. 8.
5. Bore holes with 3/16" wood twist drill; countersink the holes and
fasten the aprons with two flat head bright wood screws
If"
No. 10.
6. Bore holes in the top with 3/16" wood twist drill, countersink the
holes and fasten top with
If"
No. 10 flat head bright wood screws.
AGRICULTURAL WOODWORKING 45
RABBIT TRAP.
Material Required.
LumberOne piece of any kind of wood (preferably old weathered),
I"x6"x8'
0"
Hardware2 doz. 8d common nails
4 staples (poultry netting)
1 piece of heavy wire
18"
long for trigger
1 piece of heavy tin or galvanized iron 4"x5|" for door
2 3d shingle nails
Stock Bill.
Pieces Dimensions Use
4 I"x6"x21" Sides, top and bottom
1 I"x4"x6" End
Directions.
As little planing as possible should be done so as to retain the weathered
surface of the wood.
1. Reduce all pieces to finished dimensions.
2. Bend the wire for the trigger as indicated in the drawing.
3. Nail the staples for holding the trigger to the bottom side of the top.
4. Nail the top and bottom to the sides, using four nails for each joint.
5. Place the trigger in position through the staples.
6. Nail the end in place using two nails for each joint.
7. Punch or drill holes
I"
from the upper edge and
|"
from each side
of the tin door and fasten door in position with staples.
8. Place the two 3d nails at places shown in the drawing for door stops
A heavy wire door made as shown in the detail drawing may be used
instead of the tin door.
Old weathered lumber is preferable to new as it more closely resembles
a hollow log.
'to
I
I
I
Upgwiar
^-
3JL
n
>/
M
TT

-Ti
J.
-r
^
f
\ \ \ \ \ \ \ \ \ \ ^ \ \ \ \ \ \ \
:^
f7
/ / / i-rrr-rr
^
.Q/-
.X
n I I I I -rj
<^-,5
^i
I
S
-^
46
AGRICULTURAL WOODWORKING 47
SEED CORN CURING FRAME
Material Required.
Lumber1 piece I"x4"x8'
0"
any soft wood
Hardware8 flat head bright wood screws Ij" No. 7
8 flat head bright wood screws
If"
No. 10
30 ft. of No. 18 annealed wire
48 3d fine shingle nails
48
AGRICULTURAL WOODWORKING
SEED CORN TREE
Material Required.
Lumber1 piece 4"x4"x6'
0"
of any kind of soft wood
1 piece 2"x6"x3'
0"
of any kind of soft wood
1 piece I"x2"x2'
6"
of any kind of soft wood
Hardware16 flat head bright wood screws
IJ"
No. 8
1| lb. lOd finishing nails
1 piece tin 12"xl2"
Stock Bill.
Pieces
Finished Dimensions
1 4"x4"x6'
0"
2 If"x6"xl8"
4
13/16"x2"x7"
Use
Tree
Foot
Braces
Directions.
1. Reduce all pieces to finished dimensions.
2. Lay out an octagon on the upper end of the
tree as shown in the detail drawing and then lay
out a chamfer on each corner of the tree to within
16"
of the lower end of the tree. Remove stock
for chamfer with plane and chisel.
3. Shape top of tree as shown in drawing,
removing the stock with the plane.
4. Lay out a half lap joint for the two pieces
for the foot; remove the stock with saw and chisel.
5. With saw and chisel, shape the lower end
of post as shown in detail of "post at bottom."
6. Place the two pieces for the foot together
and bore a
2"
hole through the center for bottom
of post.
7. Brace the post as shown in the drawing, us-
ing two screws at each end of each piece.
8. Cut a square hole in the center of the tin
mouse guard as large as the tree and strip on the
tree to bottom of chamfer.
9. Place nails
3"
apart in a staggered position
at about such slant as shown in drawing.
Fig. 29. Seed Corn Tree
AGRICULTURAL WOODWORKING
49
CHICKEN BROODER, COOP AND RUN
Material Required
Lumber1 piece soft pine, cypress, fir or basswood l"xl"xl2'
0"
2 pieces soft pine, cypress, fir or basswood I"xl0"xl2'
0'
Hardware

j lb. 6d common nails

J
lb 8d common nails
30 8d finishing nails
16 3d fine shingle nails
16 flat head bright wood screws
IJ" No. 9
27 flat head bright wood screws |"
No. 6
1 piece of fine screen 6"xll"
1 piece of fine screen 10^"xl2"
1 piece of
1"
mesh chicken wire 13"x3'
9"
1 piece of
1"
mesh chicken wire 13"x5'
0"
1 piece of
2"
mesh chicken wire 27"x5'
0"
2 gate hooks and eyes
1 piece heavy tin ll"xl4^"
1 piece heavy tin or galvanized iron ll"xl6j"
1 piece heavy wire
16"
J
lb.
I"
galvanized poultiy netting staples
50
AGRICULTURAL WOODWORKING 51
4. Nail the battens over the joints on top of the coop with 3d fine shingle nails.
' 5. Nail the sides to the ends of the box by using four 8d common nails at each side of
the back end and five 8d common nails at each side of the front end.
6. Fasten the two main front pieces by naihng to them the |"x2"x24" cleat on the in-
side at the top. Cut gains l"wide and
J"
deep,
6"
from the top on the inside edges of the main
front pieces.
7. Fasten the two pieces in position indicated in the drawing by toenailing them to the
two main front pieces and fasten the 6"xll" fine screen with poultry netting staples.
8. Assemble the side door by using two 8d finishing nails to hold the butt joint at each
corner.
9. Fasten the 105"xl2" piece of fine screen to the side door with poultry netting staples.
10. Cut the head from an 8d finishing nail and cut it into two equal pieces for pivots
for the side door. Drill holes for the pivots in the door and sides of run as indicated in the
drawing and place pivots in the door.
11. Cut gains
j"
deep in one edge of two pieces for sides of run
18"
from one end for
cross brace and fasten in place with two 8d finishing nails at each end.
12. Cut gains at both ends of corner posts
^"
deep x
2"
wide as shown in detail of cor-
ner and fasten corners of coop by placing four 8d finishing nails as shown in detail.
13. Fasten run to coop by driving four 1|" No. 9 fiat head bright wood screws through
each side of run into the coop.
14 Bore hole through the center of the door button and fasten in place with one
f"
No. 6 screw.
15. Cut the ll"xl45" piece of heavy tin to the pattern shown in front of coop, drill a
hole for screw in each flange, bend flange and place door in position with two
f
" No. 6 screws.
16. Bore
|"
holes in ll"xl6^" piece of sheet metal for ventilation, fold one end over the
heavy wire as shown in detail drawing and fasten over front of main door with one staple
at each end.
17. Fasten the straps to the pieces for the end gates by using two
|" No. 6 screws at each
joint.
18. Cut grooves
f"
deep and
If"
wide in the straps for doors at end of run to receive
the end gates.
19. Place gates in position and nail straps to end of run with two nails at each joint.
20. Fasten the chicken wire to sides and top of coop.
21. Fasten the rain shield in position shown in drawing by driving two 6d common
nails into each main piece at front of coop.
22. Paint the coop and run if desired.
Fig. 30. Chicken Brooder, Coop and Run.
52
AGRICULTURAL WOODWORKING
53
KITCHEN STOOL
Material Required.
Lumber1 piece of oak, maple, basswood or white pine I"x9"x9"
1 piece of oak, maple, basswood or white pine l"x6J"x24"
Hardware12 flat head bright wood screws 2j"
No. 12
Stock BiU.
Pieces Finished Dimensions
Use
1 13/16"x9"x9" Top
4 13/16"xl3/16"x23|"
Legs
2 13/16"xl3/16"xlO" Braces
2 13/16"xl3/16"x8|" Braces
Directions.
1. Reduce stock to finished dimensions.
2. Lay out and cut a
|"
chamfer on upper edges of top.
3. Set the T-bevel by using the figures 12 and
2i
on the steel square and lay out
and cut the beveled ends of both legs and braces.
4. Find the centers of ends of braces and upper ends of legs by drawing lines diagonally
across the ends and bore a hole about
f"
deep with No. 5/32 twist drill.
5. Locate points on top board at each corner 1^"
from each edge.
6. At points just located bore holes with No. 7 twist drill. Use the T-bevel as set
for the bevel cuts of legs to guide the bit at the same angle that the legs are to assume.
7. Bore holes with No. 7 twist drill for all braces; two braces to be placed
9"
and two
13"
from the bottom of the stool.
8. Countersink all screw holes and place screws.
9. The stool may be finished with two coats of shellac or interior paint.
CLOTHES LINE REEL
Material Required.
Lumber1 piece basswood, white pine, gumwood, redwood, oak or maple I"x6"xl4"
Hardware2 carriage bolts 5"x4j" with three washers each.
Stock Bill.
Pieces Finished Dimensions Use
1 f"x6"xl4" Reel
2
f
" round x
2f
" long Handles
Directions.
1. Reduce reel to finished dimensions.
2. Draw a centerline lengthwise of stock on both sides.
3. On centerline at each end of stock swing an arc with a
1|"
radius so that edge of
arc is 3|" from end of stock.
4. Draw lines across ends |"
from edge and from these points draw lines tangent
to the arcs.
5. Remove the stock at ends with rip saw and turning saw or coping saw.
6. Round the corners as shown in the di-awing with the chisel.
7. From the stock taken from ends square up two pieces
f"xf"x2f"
for handle.
8. Bore a {"
hole through center of both pieces lengthwise.
9. Round the handle by laying out an octagon at each end, cutting the stock octagonal
in shape with the plane and then removing the edges until stock is round.
10. On a hne drawn across the stock
6"
from one end lay out a
f"
square
1"
from one
edge and remove the stock with a
f"
bit and chisel.
11. Bore a
I"
hole in edge of stock to meet the center of the square hole.
12. Bore a
I"
hole in opposite edge
1"
from the
8"
end.
13. Placekandles in position, using one washer at the head of the bolt, one between
handle and reel and one next to the nut.
14. Mar the thread on the bolt slightly to prevent the nut from coming off.
15. Bore a 5/16" hole through the reel 1|"
from one edge and
4"
from one end and
cut an opening to hold the end of the clotheshne.
54
AGRICULTURAL WOODWORKING 55
STEP LADDER
Material Required.
Lumber1 piece of white or Norway pine I"x8"xl0'
0"
Hardware18 flat head bright wood screws
2"
No. 10
4 flat head bright wood screws 2^" No. 10
4 round head bkied wood screws
|"
No. 6
2, 2"x2" steel box hinges
1 piece leather or canvas strap
21"
long
(0 $
56
AGRICULTURAL WOODWORKING 57
SWINGING FARM GATE
Material Required.
Lumber1 piece white or yellow pine, fir or cj^press I"x6"xl8'
0"
5 pieces white or yellow pine, fir or cypress I"x6"xl6'
0"
2 pieces white or yellow pine, fir or cypress I"x6"xl2'
0"
1 piece white or yellow pine, fir or cypress I"x4"x7'
4"
1 piece hardwood
f
" round x
6"
long
Hardware25 carriage bolts |"x3"
4 carriage bolts |"x2|"
2 pair screw hook and strap hinges
25 6d nails
Stock Bill.
Pieces
I
I
58
AGRICULTURAL WOODWORKING 59
TRAP NEST
Material Required.
Lumber2 pieces white pine, cypress, fir or redwood I"xl0"xl4'
0"
1 piece white pine, cypress, fir or redwood f"xll"x24"
Hardware1 piece iron 5"x5"x6"
1 iron rod j"x30"
5
lb. 6d common nails
lb. 8d common nails
4 round head blued wood screws
f
" No. 7 for angle irons
2 round head blued wood screws Ij" No. 10 for triggers
Pieces
2
2
1
1
6
2
2
1
4
2
2
Directions.
1. Reduce all pieces to finished dimensions.
2. Fasten the ends and partition to the floor by driving three 8d common nails through
the floor into each board.
3. Nail the front in place using two 6d common nails at each joint.
4. Fasten the sills to the bottom with four 8d nails for each sill. The nails should be
driven through the floor and into the ends.
5. Use two 6d nails to fasten the step. The nails may be placed at a slant so as not to
come through and require clinching.
6. Nail the back boards in the same manner as the floor.
7. Nail the top boards in place using two 8d nails at each joint.
8. Fasten the side straps by driving one 6d nail through each top board at the end and
two 6d nails into each end board. Place nails which go into the end boards at a slant.
9. Locate points on end boards and partition
|"
from top and
1"
from front and bore
I"
hole for rod.
10. Drill holes in angle iron and bend as shown in detail drawing and fasten to top of
doors with two round head blued wood screws
f"
No. 7.
11. Make triggers to dimensions shown in detail drawing and place in position shown
in side view using Ij" No. 10 round head blued wood screws.
12. Place nails to prevent door from swinging forward.
Stock Bill.
60
AGRICULTURAL WOODWORKING 61
Lumber-
HIVE SEAT AND TOOL BOX
Material Required.

1 piece white pine 13/16"xl2"x3'

4"
1 piece white pine |"xll"x22"
1 piece white pine i"x6"x6'
0"
[ardware-
-^
62
AGRICULTURAL WOODWORKING
63
LADDER
Material Required.
Lumber2 pieces ash or yellow pine 2"x4"xl6'
0"
2 pieces ash or yellow pine |"x2j"xl4'
0"
Hardware64 flat head bright wood screws
2"
No. 12
Stock Bill.
Pieces Finished Dimensions
Use
2 lf"x3|" at foot and 2^" at top x
16'
0"
Stringers
16 |"x2j" X length of various rungs Rungs
Directions.
1. Taper the stringers to
2^"
at the upper ends, using one stringer as a straight edge
for laying out the taper on the other.
2. Place stringers on the floor or bench in the position which they are to assume when
assembled, place lower rung in position and set the T-bevel for laying out the gains for the
rungs.
3. Lay out and cut gains
f"
deep and as wide as the rungs 11"
apart. Several saw
kerfs at each joint makes it easier to remove the stock than if only two were used, one at each
edge of the gain.
4. Cut rungs to length.
5. Bore and countersink holes for two
2"
No. 12 screws at each joint and fasten rungs
in place. The holes should be countersunk deep enough so that the heads of the screws will
be slightly below the surface of the wood.
FRUIT LADDER
Material Required.
Lumber2 pieces ash or yellow pine 2"x4"xl4'
0"
1 piece ash or yellow pine 2"x25"x2'
4"
1 piece ash or yellow pine |"x2|"x3'
4"
2 pieces ash or yellow pine |"x2j"x8'
0"
1 piece ash or yellow pine |"x2"x3'
0"
Hardware44 flat head bright wood screws
2"
No. 12
3,
i"
carriage bolts, 1
5i",
1
5f",
1
6J"
Stock Bill.
Pieces Finished Dimensions Use
2 l|"x3f" at foot and
2
J"
at top x
14'
0"
Stringers
1 If"x2i"x2'
4"
Top
1 i"x2i"x3'
4"
Bottom Rung
7
|"x2J"
X length of various middle rungs Middle Rungs
3 |"x2" X length of 3 top rungs Top rungs
Directions.
1. Taper the stringers to
2^"
at the upper ends.
2. Draw a line around top piece
12"
from bottom end and from this line lay out a taper
so that upper end of stock will be
1"
thick x
2"
wide.
3. Place the stringers on the floor or bench in the position which they are to assume
when finished and lay out the bevel at the inside of the upper ends so as to fit snugly against
the top. Remove the stock with a rip saw.
4. Place the bottom rung in position and set the T-bevel for laying out the gains in
top of stringers.
5. Mark positions for gains in top of stringers and cut gains
f
" deep and as wide as the
rungs.
6. Place top in position and bore three
J"
holes in position shown in drawing and bolt
top in place.
7. Cut bottom rung to length and fasten with two
2"
No. 12 screws at each end.
8. Cut all other rungs to length and fasten same as bottom rung.
64
Stock Bill.
66
AGRICULTURAL WOODWORKING 67
TWO-MAN WEIGHT CARRIER
Material Required.
Lumber1 piece of oak, maple, birch or other hard wood, 2"x8"x8'
0'
1 piece of
^"
maple doweling
34"
long
Pieces
2
4
Stock Bill.
Finished Dimensions
If
"x4"x4'
0"
If"x2i"x24"
Use
Arms
Cross pieces
Fig. 33. Two-Man Weight Carrier.
Directions.
1. Reduce all pieces to finished dimensions.
2. To lay out handle draw a line across edge of arm
12"
from end and
from this line draw a
45
line on both sides of stock to meet line drawn length-
wise of stock
If"
from the upper edge. Remove the stock to line with a rip saw.
3. Lay out an octagon on end of arm using the method shown in detail
drawing and remove the stock for chamfers with chisel, mallet and drawknife.
The handles may be rounded by removing edges with plane and chisel if so
desired.
4. Lay out mortises on both sides of arms for tenons at ends of cross
pieces, mortises to be l"x2|" with top of mortise 1|" from upper edge of arms,
mortises to be spaced as shown in top view.
5. Draw a centerline lengthwise of mortises and remove stock with a
1"
bit, chisel and mallet.
6. Lay out and cut tenons at ends of cross pieces to measurements shown
in detail drawing and cut a
|"
chamfer at end of tenon.
7. Assemble the carrier, draw joints up tight and bore
^"
holes for dowels
through arms and center of tenons.
8. Place dowels in position.
68
AGRICULTURAL WOODWORKING 69
SAW HORSE
Material Required.
Lumber1 piece white or yellow pine If"x6"x3'
0"
1 piece white or yellow pine 13/16"x4"x8'
0"
1 piece white or yellow pine 13/16"x6"x20"
Hardware24 flat head bright wood screws
If"
No. 10
Stock Bill.
Pieces
Finished Dimensions
1 If'xSr'xB'
0"
4 13/16"x3f"x25i"
2
13/16"x5|"xl0"
Use
Top
Legs
Braces
Fig. 34. Saw Horse in Use.
Directions.
1. Reduce all pieces to finished dimensions.
2. Lay out the bevels at the ends of the legs with the T-bevel and re-
move stock to line with saw.
3. Bevel the edges of the legs at the angle shown in the detail drawing.
4. Lay out and cut openings in the top for the legs
^" deep at the top
with the T-bevel set at the same angle as for the ends of the legs.
5. Lay out and cut the bevels at the ends of the braces.
6. Bevel the edges of the braces so that they fit tightly against the top.
7. Assemble the parts by placing the screws as indicated in the drawing.
70
AGRICULTURAL WOODWORKING 71
LAWN OR PORCH SEAT
Material Required.
Lumber1 piece basswood or white pine 13/16"x8"x8'
0'
1 piece basswood or white pine |"xl0"xl4'
0"
Hardware30 round head blued screws 1|" No. 9
46 flat head bright wood screws Ij" No. 8
72
AGRICULTURAL WOODWORKING 73
DAILY MILK RECORD SHEET CASE
The ordinary way of keeping a milk record sheet is that of tacking it to a wall in the
barn and making the record at milking time. The result is a soiled sheet which must be
recopied before it can be put on file.
The purpose of the daily milk record sheet case is to provide a place for keeping the
record sheet clean as the record is made and hence dispensing with recopying for a permanent
record and also to reduce the possibiUty of error to a minimum.
Material Required.
Lumber1 piece of any soft wood I"x8"xl8"
1 piece of any soft wood |"x6"x4'
0"
1 piece of any soft wood |"x7"x3'
0"
Hardware1 piece tin, IC,
17i"xl6i"
1
J"
rod
20"
long
6
i"
washers
2 i"nuts
1
I"
thumb nut
3 8d finishing nails
42 4d finishing nails
24
I"
No. 17 lining nails
9 thumb tacks
Stock Bill.
Pieces Finished Dimensions Use
3 f"x5|"
diameter Cyhnder
1 i"x7"xl7f"
Bottom
2 |"x5|"x6" Ends
2 ^"x5r'xl7f"
Sides
2 |"x3 3/16"xl7f"
Top
1 f"xl"xl6|"
Brace
Directions.
1. With band saw, turning saw or coping saw, saw out the
Sf"
cyhnders.
2. Reduce all other pieces to dimensions.
3. Bore
j"
holes through center of cylinders.
4. Lay out opening for brace in cyhnders
|"
deep and
1"
wide and remove stock with
handy saw and coping saw.
5. Thread
2f"
of one end of the rod and bend
1"
of opposite end at a right angle.
6. Place ends of box, washers, nuts and cyhnders on rods as indicated in the drawing.
7. Bend
J"
of one of the
16i"
edges of the tin as shown in the detail drawing, clamp
tin at X with the brace and fasten brace in position with one 8d finishing nail in each cyhnder.
8. Fasten tin to cylinders with lining nails spaced about
3"
apart and nail end of tin to
brace.
9. Nail sides of box to ends, using three 4d finishing nails at each joint.
10. Nail bottom of box to sides and ends.
11. Lay out a
2"
bevel on top pieces as indicated in end view of drawing and remove
stock with plane.
12. Nail top pieces in place.
13.- Fasten one end of daily record sheet to brace with three thumb tacks, loosen the
thumb nut and with other end of rod as a crank turn cyhnder one revolution and fasten other
end of sheet with two thumb tacks, lock cyhnder in place with thumb nut.
14. Write the names of cows on a sheet of paper similar to the headings on the record
sheet and fasten in position indicated in the drawing with two thumb tacks. A piece of
scrap paper should be fastened to the top at front with two thumb tacks so as to keep the
top of box clean.
74 AGRICULTURAL WOODWORKING
T
n
^rU-
-^
76 AGRICULTURAL WOODWORKING
OATS SPROUTER
Material Required.
Lumber1 piece 2"x4"xl0'
0"
white pine, cypress, fir
1 piece 2"x4"xl2'
0"
white pine, cypress, fir
2 pieces I'''x8"xl2'
0"
white pine, cypress, fir
2 pieces ^"x8"xl2'
0"
white pine, cypress, fir
Hardware16 flat head bright wood screws
3"
No. 14
16 flat head bright wood screws 1|" No. 9
30 flat head bright wood screws
1^"
No. 7
1 lb. 6d common nails
AGRICULTURAL WOODWORKING
77
5. Fasten the rests for flats by using two 6d common nails at each end
of each piece.
6. Fasten the guides to the rests by placing three
IJ" No. 7 screws in
each piece as indicated in the drawing.
7. Assemble the flats by driving three 6d common nails through each
end of each side piece, four nails through the end piece into the bottom,
and five nails through each side into the bottom; spaced as in detail of flat.
8. A space of
I"
should be left between the two pieces for the bottom and
I"
holes bored as shown in the drawing, to permit proper drainage.
^^'
Fig. 36. Oats Sprouter.
78
AGRICULTURAL WOODWORKING
79
FRUIT LADDER
Material Required.
Lumber2 pieces white or Norway pine 13/16"x4"x8'
0"
1 piece white or Norway pine 13/16"x8|"xl2'
0"
Hardware
3|
doz. flat head bright wood screws 1^" No. 9
1 |"x26|" rod with washers
^y- ^
80
AGRICULTURAL WOODWORKING 81
WAGON BOX
Material Required.
Lumber2 pieces poplar or basswood 2"x4"xl0'
0"
2 pieces poplar or basswood I"xl2"xl2'
0"
4 pieces poplar or basswood I"x9"xl2'
0"
1 piece poplar or basswood l"xll"x6'
0"
1 piece poplar or basswood I"xl0"xl0'
0"
Hardware8 wagon box strap bolts
8 wagon box side braces
2 wagon box rods
2 dash braces
2 rub irons
36 carriage bolts
f
"x3|" for floor and running boards.
8 carriage bolts |"x2^" for floor
24 carriage bolts
f
"x2|" for side and end cleats.
38 carriage bolts J"xl^" for strap bolts, side braces and rub irons
4 carriage bolts \"x2\" for dash braces
2 carriage bolts
J"x2"
for dash braces
Stock Bill.
Pieces Finished Dimensions Use
4 2"x 4"x
4'
2"
Cross sills
2 l"x 3"x
3'
2"
Cross sills
2 I"xl2"xl2'
0"
Sides
2 l"xll"x
3'
0"
End gates
4 l"x 9"xl2'
0"
Floor
2 l"x 3"x
3' 0"
Running boards
1 l"x 8"x
3' 2"
Dash board
12 l"x 2"xll" End and sideboard cleats
Directions.
1. Reduce all pieces to finished dimensions.
2. Fasten floor to cross sills by using eight
f
"x3|" carriage bolts for each
board, two through each sill. All nuts should be locked by slightly marring
the thread with a cold chisel.
3. Fasten wagon box trap bolts in place on side boards and bolt in place
through cross sills.
4. Bolt running boards in place, using one
f
"x3|" carriage bolt at each
end of each board, through the cross sills.
5. Fasten wagon box side braces in positions indicated in the drawing.
6. Fasten rub irons in place at edges of box.
7. Fasten cleats to side boards and rear end gate by using two
f"x2^"
carriage bolts for each cleat.
8. Bevel the lower edge of the dash board and fasten to front end gate
by bolting dash braces in place. The two bolts which hold the lower ends
of the dash braces should pass through the end gate cleats.
9. Fasten the rear axle cross rests in place, using one
f"x2^"
carriage
bolt for each board through each rest.
I
I
i
j //'s
^^''^A \
I
AGRICULTURAL WOODWORKING 83
FLAT HAY RACK
Material Required.
Lumber2 pieces yellow pine 2"x8"xl6'
0"
3 pieces yellow pine 2"x4"xl4'
0"
3 pieces yeUow pine 2"x4"xl2'
0"
2 pieces yellow pine 2"x4"xl6'
0"
1 piece yellow pine 2"x4"x8'
0"
2 pieces yeUov/ pine 2"x6"xl4'
0"
1 piece yellow pine 2"x2"x3'
0"
1 piece yellow pine I"x6"xl4'
0"
13 pieces yellow pine flooring 13/16"x6"xl6'
0"
Hardware8 hayrack clamps
16J"
long
14 carriage bolts
|"x6i"
1 lb. lOd common nails
4 pieces strap iron |"xl"x7"
1 quart of outside paint
84
AGRICULTURAL WOODWORKING 85
CARPENTER'S WORK BENCH
Lumber1 piece 2"xl0"xl0'
0"
maple
1 piece 2"x8"x2'
8"
maple
2 pieces 2"xlO"xlO'
0"
select white pine
1 piece 2"x4"xl6'
0"
select white pine
1 piece 2"x4"x3'
0"
maple
1 piece 2"x6"xl0'
0"
No. 1 white pine
3 pieces I"xl0"xl0'
0"
No. 1 white pine
1 piece i"x8"xl2'
0"
No. 1 white pine
1 piece I"xl0"x2'
0"
maple
Material Required
Hardware-
Pieces
1 maple
2
1 maple
5
3
2
1
2
3
2
2
1
2
1
2
1
2
1
1
1
1
Stock Bill
Finished Dimensions
I|"xl0"xl0'
0"
If"xl0"xl0'
0"
Ij"x3r'x2'
8i"
Ii"x3f"x2' Si"
I|"x5|"x2' 2|"
i"x9f'xlO'
0"
I"x8"x2'
2f"
|"xli"x8"
5"x3|"x2'
2J"
i"x3|"x4'
5J"
|"x2"xl' 9|"
i"x7"x2'
0"
i"x7"x23|"
i"x6"x23"
Vx8"x23f"
J"x7"x23|"
I"x3"x2'
2f"
If"x7f"x2'
7"
j"x5J"xl6"
i"x2f"xl6"
I"x3i"x6"
-18 carriage bolts |"x7" with washers
12 carriage bolts j"x4i" with washers
1 carriage bolt i"x4j" with washers
42 flat head, bright screws
2"
No. 12
15 flat head, bright screws IJ" No. 10
1
16"
Ij" bench screw
1 iron pin i"x44"
Use
Top
Top
Leg
Legs
Cross rests
Side aprons
Shelf
Shelf rests
Leg braces
Braces
Cross shelf rests
Drawer front
Drawer sides
Drawer back
Drawer bottom
Drawer bottom
Drawer rests
Vise
Vise
Vise lock
Bench stop
Directions
1. Reduce all pieces to finished dimensions.
2. Lay out and cut notches l"x5f" on one edge at one end of each leg to receive the cross rests.
3. Lay out and cut out the dadoes i"x3|" on the legs for the leg braces,
6"
from the lower end of each leg.
4. Lay out the vise to a 3
1"
taper at the lower end and
6"
at the upper end and remove the stock to
line with saw and plane.
5. Lay out and cut a
\" chamfer on one side of the vise at both ends and both edges.
6. Taper the front piece for the vise to
3f"
at each end.
7. Chamfer the front piece the same as main piece for vise.
8. Bore |" holes for j" iron peg in the vise lock at points shown in section drawing.
9. Lay out and cut an opening at center of lower end of vise j"x2J" to receive the vise lock and fasten
vise lock in place with a |"x4i" carriage bolt.
10. Lay out and cut a mortise in the maple leg; the mortise to be 15/16"x2 13/16" on a centerline, drawn
lengthwise of the stock; the upper end of the mortise to be
6"
from the lower end of the leg.
11. Fasten the front support of the vise to the main piece by using four IJ" No. 10, flat-head, bright
wood screws; heads of screws to be neatly countersunk.
12. Locate a point on a centerline, drawn lengthwise of the vise
10"
from the upper end of the stock,
and bore a
1"
hole for the bench screw.
13. Fasten bench screw in place on the vise.
14. Fasten the cross rests to the legs by using two i"x4|" carriage bolts at each joint.
15. Place the leg braces in position and fasten with two
2"
No. 12 wood screws at each joint.
16. Fasten braces in position using two screws at each leg.
86 AGRICULTURAL WOODWORKING
17. Fasten cross shelf rests using two
2"
No. 12 screws thru the braces into each end of each brace. The
upper edge of rests and braces to be flush.
18. Place the aprons and fasten with three
2"
No. 12 wood screws into each leg.
19. Cut two openings in the front apron; one to be l"x2'
0"
for a board support and the other to be
7"
x2'
0"
for the drawer. These openings to be cut at places indicated in the drawing.
20. At the end of bench opposite from the vise fasten the shelf rests at position shown in end elevation.
Two H" No. 10, flat-head, wood screws should be driven through each rest and into the apron.
21. Lay the shelf on the shelf rest and fasten with two screws at each end.
22. Shape two pieces of stock
2'
2f"
long for drawer to slide on as shown in the front elevation and
fasten in place by driving two
2"
No. 12 wood screws through the aprons into each end.
23. Build a drawer to given dimensions. Stops should be placed so that the front edge of the drawer
will close flush with the front apron.
24. Bore a
1"
hole in the maple leg and through the apron for the bench screw; the hole to be on a cen-
terline, drawn lengthwise of the stock
8i"
from the upper end of the leg. Cut keyway for the key on the nut
of the bench screw and fasten nut in place with sTrews.
25. Bore a |" hole through the maple leg for the iron pin.
26. Bore |" holes in the front apron for maple peg at points shown in front elevation.
27. Place top planks in position. Locate points for bolts as indicated in top plan. Bore holes in planks
I"
deep large enough to drop the heads of bolts. Finish the holes with |" bit through the planks and cross
rest.''. Bolt top firmly in place.
28. Plug the bolt holes.
29. Make a maple bench stop to given dimensions and fasten with five 1 j" No. 8, flat-head bright
wood screws; heads of screws to be countersunk below the surface of the stop.
Fig. 37. The Work Bench and Tools in Shop.
AGRICULTURAL WOODWORKING 87
Fig. 3S. Corner in Workshop. Note Forge and Tools.
A FARM WORKSHOP
A farm shop, suitable for the average farm, is illustrated on page 88. It was de-
signed to meet ordinarj' needs without an unnecessary outlay of either material or equipment.
The tools which make up the equipment, are those necessary for the ordinary farm and for
keeping the equipment of such a farm in order. The individual must use good judgment in
selecting standard tools, the size and weight of which suit his particular needs and the con-
ditions which his particular farm presents.
The building is 16 feet by 20 feet with 12-foot posts. The joists for the attic are placed
for a 9-foot ceiling. The roof is half pitch, providing a large attic for storage purposes. The
door is 8 feet by 8 feet which is a convenient size for admitting all kinds of farm machinery
and equipment. Two large windows have been placed at each side of the shop and one small
one in each gable for the attic. A door 2 feet 6 inches by 3 feet has been built above the main
door, to admit lumber into the attic. A stock of lumber should always be kept on hand on
the attic shelves.
On one side, between the windows, a work bench 2 feet 6 inches wide, 10 feet long and 2
feet 10 inches high is built. The front end of the bench is equipped with a homemade wooden
vise which has an iron bench screw. At the other end is fastened a metal vise. The top of
the bench is made of three 2-inch by 10-inch planks, the front one of which is maple, the
others pine. The woodworking tools are arranged on the wall over the work bench, within
easy reach of the workman at the bench.
On the other side, at the rear corner, stand the forge and anvil. The forging tools hang
on either the anvil block, or on the rack on the wall near the forge. On the same side, in the
other corner, stands the stove. The smoke pipes from the stove and forge lead to the chim-
ney, which is constructed of sewer tile and stands on a bracket. The chimney extends higher
than the ridge of the building and is braced by rods. The drill press is fastened to the wall
near the forge, and next to this is the grinder.
88
^
^ A ,v: j; fV^ ^
iO v
BD
89
90 AGRICULTURAL WOODWORKING
The remaining wall space is sufficient for conveniently hanging all the farm tools. A
silhouette of each is painted on the wall in its proper place so that when a tool is missing one
can easily detect what it is. In a corner is a waste box over which hangs a broom.
At the rear of the room is a stairway leading into the attic over which is a trap door.
This door is manipulated by a rope hung over a pulley. This permits closing off the attic
from the rest of the building in cold weather.
Lumber for Farm Shop.
9 pc. 2"x
4"

16'
Hemlock or Y Pine
5 pc. 2"x
4"

20'
Hemlock or Y Pine
3 pc. 2"x
4"18'
Hemlock or Y Pine
26 pc. 2"x
4"14'
Hemlock or Y Pine
38 pc. 2"x
4"12'
Hemlock or Y Pine
11 pc. 2"x
6"16'
No. 1 White Pine
3 pc. 2"x
8"14'
No. 1 White Pine
4 pc. I"xl2"
10'
No. 1 White Pine
4 pc. I"xl2"
14'
No. 1 White Pine
10 pc. l"x
6"12'
No. 1 White Pine
10 pc. l"x
6"14'
No. 1 White Pine
5 pc. l"x
6"10'
No. 1 White Pine
7 pc. l"x
4"12'
No. 1 White Pine
14 pc. l"x
4"10'
No. 1 White Pine
22 pc. I"xl0"
10'
No. 1 White Pine
3 pc. l"x
8"14'
No. 1 White Pine
1160 ft. No. 1 White pine drop siding.
1585 ft. No. 1 White pine matched fencing
6"
500 ft. Hemlock roof boards
6000 *A* Shingles
Hardware for Farm Shop.
12 lbs. 20d Nails
5 lbs. lOd Nails
60 lbs. 8d Nails
20 lbs. 3d Shingle Nails
6
12"
Extra Heavy "T" Hinges
2
8"
Heavy "T" Hinges
2
6"
Strap Hinges
12 Window Spring Bolts
1
6"
Hook with Staple
1 Barn Door Latch
7"
long with Padlock
Hasps
1 Padlock
18 ^"x6" Carriage Bolts with Washers
Lumber for Work Bench for
Farm Shop.
1 pc. 2"xl0"
10'
Maple
2 pc. 2"xl0"
10'
Select white pine
1 pc. 2"x4"
16'
White Pine
3 pc. I"xl0"
10'
White Pine No. 1
1 pc. 2"x6"
10'
White Pine No. 1
1 pc. I"x6"
16'
White Pine No. 1
1 pc. 2"x8"
2'
8"
Maple
1 pc. 2"x4"
3'
Maple
1 pc. ^"x8"
12'
White Pine
1 pc. I"xl0"
2'
Maple
Carpentry Tools for Farm Shop.
1
26"
Cross Cutsaw $ 1.10
1
26"
Rip Saw 1 . 10
1 Jack plane
14"
with
2"
cutter 1 . 80
1 Carpenters' draw knife 55
1 Marking gauge 15
1
8"
Try Square 25
1 Mallet 22
1 Saw Set 80
1 Set of Auger Bits, 4/16" to 16/16"
inclusive 4 . 70
1 Ratchet Brace 1 . 50
2 Screwdrivers, 1 largo, 1 small 72
1 Countersink 20
1 Steel rafter framing .square 1 .00
1 Pair Pliers 70
1
10"
Flat file 15
1
8"
Triangular file
3
1
6"
Slim tapered triangular file
1
12"
Half-round wood file
1 Pair
8"
winged dividers
1
8"
Oblong carborundum oil stone. . .
1 16-oz. Straight claw hammer
1
24"
Carpenter's level
1 Nail set
1 Putty knife
'.
4 Socket firmer chisels

j", ^",
1",
U"
1 2-lb. 2-oz. Bench hatchet
1 Myers P^amous Lock Stitch, Sewing
Awl with skein of thread and 1
doz. needles andl ball wax
1 2-ft. four-fold boxwood rule
0.12
.10
.32
.55
.85
.50
.90
.05
.15
1.40
.60
.75
.25
Total $21.48
AGRICULTURAL WOODWORKING 91
Blacksmithing Tools for Farm Shop.
Farmer's Anvil70-lb., cast iron body,
steel face $ 5.00
Farmer's Forge 6 . 00
Blacksmith's Hand Hammer1-lb.,
10-oz 44
Machinist's Hammer, 1-lb., 8-oz 37
1 Straight Lipped j" opening, 18"
length blacksmith's tongs 40
1 Bolt Tongs,
f
"
to ^",
20"
length 50
1 Pair Fluted Jaw Tongs for |" to
5/16" iron,
18"
50
1 Steel Square, 12"x8" 50
1 Hardie to fit Farmer's Anvil 35
1 Bonney's Farmer's Vise 3 . 10
1 No. 1 Silver's Blacksmith's DriU .... 5 . 60
1 Set Cleveland Twist Drill Bits, |"
to
1"
by sixteenths (Shank to fit
No. 1 Drill) 4.25
1 10-lb. Blacksmith's Cross Pein
Sledge 60
1 Top Fuller |"
to 9/16" with handle . . 35
1 Bottom Fuller
i"
to 9/16" with
handle
$ . 40
1 Square Flatter I5" face with handle. . 15
1 Set Hammer 1"
Sq. Face with
handle 30
1 Cold Cutter
If" face with handle. . .50
1 Hot Cutter
If"
face with handle. . . .40
1 No. 9 Star Hack Saw Frame with 1
doz. blades (12" frame and blades) 1 . 20
1 Agricultural Wrench 21" opening. . . .60
1 Always ready alligator wrench,
7"
length 80
1 5-lb. box cherry heat welding com-
pound 40
1 Spring Belt punch four tube 75
1 Scratch Awl 10
1 Grinder with one coarse and one
medium dimo grit wheel 8.50
1 Set of Stocks and Dies 4.00
1 Copperized Oiler 15
1
14"
Pipe Wrench 75
Total $46.96
Farm Tools to be Stored in Farm Shop.
Crowbav, 10-lb
$ 0.40
Corn Hook 25
Scythe 75
Snath 70
Ax, 4-lb. (handled) 80
Ironed Neckyoke 55
Singletree 45
Evener 65
1 lb. Frazer Axle Grease 10
Axle Oil 22
Handled Cast Post Maul, Speery's
Pattern, 16-lb 65
1 MiU and Warehouse Broom 43
Wire-stretcher, Benedict's Improved
Jumbo 65
Log Chain, 5/16" diam., 12 ft. length . 1 . 00
Post Hole Digger (Atlas) 1 . 00
Mattock 50
One Man Cross Cut Saw (Champion
Tooth), 4-ft 1.60
Hay fork, 4-ft. Handle
$ 0.45
D. Handle Spade 60
Garden Rake
55
Clover Rake
50
1 lb. High Grade Cup Grease 20
Cant Hook (4-ft. handle) 1 . 15
Heavy Bush Scythe 75
Bush Snath
75
Carborundum Scythe Stone 18
Buck Saw
50
Watering Pot, 16-quart
38
Hay Knife (Weymouth) 70
Spading Fork
65
Manure Fork, 4-ft. Handle
55
Harness Oil, 1 pint 25
Ensilage Fork 1 . 15
Sanderson Grain Scoop 90
Potato and Vegetable Scoop 1.10
1 Bolster Spring, 1,000-lb. xxx 1 . 85
1 Garden Hoe 55
"Total $24.41
^
92
AGRICULTURAL WOODWORKING
93
ENSILAGE RACK
Material Required
Lumber2 pieces of white or yellow pine 6"x6"xl6'
0"
2 pieces of white or yellow pine 2"x6"xl2'
0"
1 piece of white or yellow pine 2"x6"xl4'
0"
1 piece of white or yellow pine 2"x4"xl2'
0"
2 pieces of white or yellow pine I"x6"xl0'
0"
17 pieces of white or yellow pine I"xl0"x6'
0"
1 piece of ash or white oak 2"x4"x3'
6"
2 pieces of white or yellow pine 4"x4"xl2"
Hardware2 U bolts |" round stock
4f"
inside, 16"
long with plate washers and nuts to carry stringers to
rear axle.
, ^
.
*
,. , , ^ , ...
,
I* To carry stringers at front
1 triangular link j stock, 4 long
i
1 piece iron |"x2"xl0" for clevis at front end of reach
2 machine bolts |"x3" to hold clevis to reach at front
1 piece iron |"x2"xl6" to hold rear end of reach
4 machine bolts |"x2J" to fasten reach at rear
3 machine bolts, one ^"x6", one Y'x9", one 5"x.j" to hold stringers together at front.
4 carriage bolts i"x8i" to hold uprights to stringers at rear
2 carriage bolts 5"xl4" to hold uprights to stringers at front
2 lbs. 8d common nails
1616d nails
Stock Bill
Pieces Finished Dimensions Use
2 6"x6"xl6'
0"
Stringers
4 2"x6''x5'
3"
End uprights
2 2"x6"x6'
0"
End cross pieces
2 2"x4"x5'
8"
Front end diagonal braces
2 I"x6"x9'
6"
Lower side cleats
17 I"xl0"x6'
0"
Floor
1 2"x4"x3'
6"
Reach
2 4"x4"xl2" Blocks below rear axle
2 2"x6"xl0" Braces for front uprights
Directions
1. Cut all pieces to dimensions called for in stock bill.
2. Draw a line across one edge of each stringer
3' 4"
from the front end and a line across the front end
of each
2"
from the outside edge. Connect the line across the end with the line across the edge and remove
the stock with the rip saw.
3. Bolt the stringers together at front with the "x5", i"x6" and i"x9" machine bolts placed 2",
6"
and 1' 9"
from the front ends.
4. On a centerline on the upper edge at the back end of stringers bore two |"
holes 4j" apart,
3"
from
the end for the U bolts.
5. Place the 4"x4"xl2" blocks between the stringers and rear axle and fasten stringers with U bolts.
6. Bore a
I"
hole on a centerline at the front end of the stringers
3"
from the end.
7. Block the stringers up under the front axle.
8. Bore holes through stringers for end uprights with
i"
bit and fasten uprights in place.
9. Fasten the end cross pieces in place, using two 16d nails in each upright.
10. Cut the braces for front uprights triangular in shape and nail to the stringers so as to fit snugly against
the front uprights. Use four 16d nails for each brace.
11. Cut an opening in the upper edge of the front cross piece at the center for the rear end of the reach.
12. Fasten the rear end of the reach to the front cross piece by bolting the |"x2"xl6" piece of iron to the
top of the reach and back side of the cross piece. Use the |"x2J" machine bolts.
13. Bend the |"x2"xl0" iron for clevis as shown in the detail drawing. Place the link in position and
fasten the clevis to the front end of the reach with the two i"x3" machine bolts.
14. Place the eye bolt through the stringers at front.
15. Nail the floor to stringers and end uprights, using two 8d nails at each joint.
16. Fasten the front end diagonal braces and the lower side cleats to the floor by using two 8d nails at
each board.
I
:^:
.^
iz
=
^ pmr P77TI FTH Rml
,.^>-
-.0/-^
i^&'
^^m:
ff
v/,1 kvvj yyyj tJsM i^y-^i t
fc:^^^^
94
AGRICULTURAL WOODWORKING 95
ROUGHAGE FEED RACK FOR SWINE
Material Required.
Lumber1 piece 2"xl2"xl2'
0"
any kind of lumber
3 pieces 2"x4"xl2'
0"
any kind of lumber
1 piece 13/16"xl0"xl2'
0"
any kind of lumber
9 pieces 13/16"x3"xl2'
0"
any kind of lumber
Hardware-
,o .&
T)'
I
I
>5
5
ct
JbJ-
l>4
-.o.e-
M
^
s;]
I
96
AGRICULTURAL WOODWORKING 97
ROUGHAGE FEED RACK FOR CATTLE
^
I
-:P.^\

98
AGRICULTURAL
WOODWORKING
99
HAY RACK
Material
Required.
Lumber2 pieces 2"x8"xl6'^0"
yellow pine
2 pieces 2"x8"xl4'
0"
yellow pine
6 pieces 2"x4"xl2'
0"
yellow
pine
1 piece 2"x4"x6'
0"
yellow pine
1 piece 2"x6"x8'
0"
yellow pine
12 pieces I"x6"xl6'
0"
yellow pine
1 piece I"x6"x3'
0"
yellow pine
Hardware8
10"
hay rack clamps
16 carriage bolts |"x5" inside boards on arms
8 carriage bolts
f
"x4^" outside board on arms
12 carriage bolts |"x4" plates to stringers
8 carriage bolts
i"x4"
front and rear
standards
2 carriage bolts |"x3|" front standard at bottom
4 carriage bolts |"x6" standards at bottom
2 carriage bolts
f
"x4" cross brace front standard
48 lOd common nails for bottom
Stock Bill.
Pieces Finished Dimensions
Use
2
If
"x8"xl6'
0"
Stringers
4
If
"x8"x3'
6"
Cross rests
5 I"x6"xl6'
0"
Floor
1
I"x4i"xl6'
0"
Floor
4 If"x6"xl2"
Plates
4 If"x6"x9"
Plates
8 If"x3f
"x5'
8"
Arms
6 |"x6"xl6'
0"
Top boards
2
If"x3f
"x5'
2"
Rear standard
2 If"x3f
"x20" Bottom front standard
2
If"x3f
"x6'
0"
Front standard
1 |"x3"x2'
7"
Brace at front standard
1 |"x3"x23" Brace at front standard
1 |"x3"xl8" Brace at front standard
1 |"x3"xl5" Brace at front standard
1 If"x3f
"x2'
8"
Brace rear standard
-d^h-
I
I
I
100
AGRICULTURAL WOODWORKING 101
KING ROAD DRAG
Material Required.
Lumber1 piece white oak or ash 4"x9"x8'
0"
front
1 piece white oak or ash 2"xl0|"x8'
0"
back
2 pieces white oak or ash 2"x4"x8'
0"
platform rests
1 piece white oak or ash 2"x4"xl2'
0"
for cross bars
3 pieces pine I"xl0"x8'
0"
platform
Hardware5 machine bolts ^"xlO" for front
5 machine bolts |"x8" for rear
11 carriage bolts
f"x4|"
for iron plate
6 lag screws
f
"x3" for top iron straps
30 flat head bright wood screws
2"
No. 12 for platform
2 pieces iron j"xl^"x2'
0"
for rub irons
1 piece iron
f
"x2"x8'
0"
Fig. 40. King Road Drag in Use.
102
AGRICULTURAL WOODWORKING 103
GRAIN BED
Material Required.
amber(Poplar)
104
106
^
c^
^
V
is
"'0
\}.
Vj, "^
5: V)
^j)"5
if'
'^
.
5
IS
i.
>>o'
V
>
ID 'i-
1-
"u
ij.
-'.A*.0*'.
4
*.0**.^4^.

.0
-^-
I
.-^:
107
I
i^v
^-ff-
n-E
4EE-
-10=^
I I I
^
108
I
>3
3! >u
^.
o
Vi vj U ^ ij" V.
5 ^ o 1^ .S
1). ^
<\1 o

m
T
^
--.?/-*
"XS
^
AGRICULTURAL WOODWORKING 111
SILO FORM
Material Required for a 12-ft. Form.
Lumber8 pieces soft wood 2"xl0"xl0'
0"
for ribs
1 piece soft wood 2"xl0"x8'
0"
for splices at joints
3 pieces soft wood 2"x6"xl0'
0"
for splices at joints and uprights
for door
3 pieces soft wood 2"x4"xl4'
0"
for studs
1 piece soft wood 2"x2"xl0'
0"
for door
1 piece soft wood 3"x4"x7'
0"
for wedges
8 pieces soft wood 2"x4"xl8'
0"
for posts for elevating the form
150 ft. 4"xl2'
0"
soft pine matched and dressed flooring for outside
of inside form, and spacing blocks
Hardware2 sheets No. 20 galvanized iron 36"x2r
5"
for outside form
12 pieces soft steel j"xlj"x6" for lugs
24 iron rivets
i"x|"
for fastening lugs
6 machine bolts ^"xlO" threaded to the head for drawing outside
form together
64 machine bolts ^"x4^" with two washers each for splices at
joints
64 20d spikes for fastening studs to ribs.
2 heavy T hinges for door
5 lbs. 8d common nails for nailing flooring to ribs
Fig. 41. Silo Form Completed.
112
AGRICULTURAL WOODWORKING 113
FARM BUILDINGS
The drawings of farm buildings on the following pages are only suggestive and it is ex-
pected that local conditions such as size of farm, type of farming and topography of the land
at the farmstead will warrant changes. If however, any one who is building, will glean
a suggestion from them on how to make the buildings handy and as a result the farming
easier, it is thought that the plans will have served a useful purpose.
It may be stated that the plans in their arrangement and type of construction are such
as are advocated by the better agriculturists.
The open front poultry house appears to be gaining in favor as it conserves the vitality
of the fowl and consequently produces more vigorous chicks the following spring.
The hog house has these particularly commendable features: it is handy in arrange-
ment; it has a ventilating system and admits sunlight in each individual pen.
Brood sows do so much better in rearing a litter of pigs in a portable house than in a
big house where there are other hogs, even though they are in a pen by theinselves, that the
portable house is being used extensively. The A type of house is most generally used be-
cause of its simplicity and ease of construction.
The corn crib built as called for in the drawing serves a double purpose: a storage place
for corn and a place between the two cribs for storing wagons, buggies or implements.
The implement shed should have a floor. The type of shed shown appears to be the
most satisfactory. The entire front is a set of doors which roll by one another as shown
in the detail drawing, making it handy to get machines in and out of any part of the shed.
It has the advantage over the open front shed in that it keeps the fowl out and prevents
the rain and snow from blowing in.
The floor plan of the small combination horse and dairy barn is only suggestive of an
arrangement of the floor of a barn for a small dairy farm.
The average farmer wishes his horses and cows in the same building so as to save time
and steps in doing the chores. With the horse and cow barn separated by a partition and
the milk house outside of the barn there is little danger of the milk becoming contaminated.
Modern barn construction calls for plenty of light. Thirty-two windows
2'
6"x3' 6", out-
side dimensions, furnishes approximately one square foot of window to twelve square feet
of floor space. The Kind system of ventilation is advocated. Twelve fresh air inlets and
four foul air flues are provided which should keep the air in the barn dry and pure. The
engine room is separated from the milk house by a wall which keeps the oily odor of the engine
from the milk. The alley between the barn and milk house is housed in so that one need not
go outside in going from the barn to the milk house. On the second floor two driveways are
provided which makes it easier for unloading hay and grain and provides a place for two
loads in case of rain or at the end of a day. The granary should be housed in with a ceiUng
not less than nine feet high. Windows should be provided in the side and end of the barn
for hghting the granary and alley. Double-hinged swinging doors are placed at each drive-
way. If sixteen instead of twelve foot posts are used, the roof will be high enough to permit
the use of rolling doors which are usually preferred. Rolling doors may be used on the
barn built to the dimensions called for in the drawing if they are hung so as to roll past each
other. In this arrangement only one driveway can be open at a time. A retaining wall
should be built not less than tv/elve feet from the barn and the span from the wall to the
driveway bridged. By use of the bridge the light is not shut off from the stable as it would
be if the approach were filled in against the barn.
I
114
115
116 AGRICULTURAL WOODWORKING
COLONY POULTRY HOUSE
Material Required.
Lumber2 pieces 4"x4"xl4'
0"
Skids
2 pieces 4"x4"x8'
0"
Cross ties
7 pieces 2"x4"x8'
0"
Joists
1 piece 2"x4"xl2'
0"
Studding
4 pieces 2"x4"xl4'
0"
Studding
2 pieces 2"x4"xl0'
0"
Studding
1 piece 2"x4"xl2'
0"
Girts
7 pieces 2"x4"xl0'
0"
Rafters
4 pieces 2"x4"xr2'
0"
Plates and sole pieces
2 pieces 2"x4"x8'
0"
Sole pieces
27 pieces I"x3i"xl2'
0"
Floor
25 pieces 6"xl2'
0"
Drop siding front and back
32 p'eces 6"x8'
0"
Drop siding ends and back
13 pieces I"x8"xl4'
0"
Roof boards
2 pieces I"x6"xl4'
0"
Fascia
2 pieces I"x6"xl0'
0"
Fascia
2 pieces I"xl0"xl4'
0"
Plancher
2 pieces I"xl0"xl0'
0"
Plancher
1 piece 2"x6"x8'
0"
Window sills
2 pieces r'x4"xl0'
0"
AVindow frames
2 pieces I"x4"xl0'
0"
Window casing
2 pieces I"x4"xl0'
0"
Door casing
4 pieces I"x4"x8'
0"
Corner boards
2 pieces I"x4"xl2'
0"
Corner boards
1 piece I"x4"xl0'
0"
Door
5 pieces 3j"xl4'
0"
flooringDoor
2 windows 10"xl2"6 light
Ij rolls of prepared roofing or 6 bundles shingles.
Hardware1 cjuart priming paint
1 quart finishing paint
4 carriage bolts
^"xGl"
with washers
2-6"
heavy strap hinges
4 butt hinges 2|"x2|" for windows at top
3 screen door hooks with screw eyes
1-6"
hasp and staple
1 padlock
10 lbs. 8d common nails
2 lbs. 20(1 common nails
117
I
ym
I I I I II I I
XT
I I I 1 I I
lA
-?-f/
J'!i|!||!|| J-
119
>5
i
120
I
121
I
t
i
5
122
II

I
123
I
a
o
s
to
E
I
^
^
^
124
I
I
125
PQ
3
o
O
O
d
o
-O
S
o
O
126
128 AGRICULTURAL WOODWORKING
BELT LACING, KNOTS, HITCHES AND SPLICES
Of the many good ways of lacing a belt, only two standard methods are here illustrated.
It is believed that if one can lace a belt well, using either of these methods he will be able to
do such lacing as is usually necessary for transmitting power in farm machinery.
Scarcely a day passes on the farm that there is not a call for a knowledge of the more
common knots, hitches and splices. The life and use of a rope is greatly enhanced by a know-
ledge of how to use, care for and repair it. Frequently a hay rope breaks and if the farmer
knows how to make the long splice, it may save a trip to town, considerable time and per-
haps a few loads of hay.
Only the more useful knots, hitches and splices are shown. It is believed that if a country
boy can make the long and short splice, properly crown the end of a rope and make the knots
and hitches illustrated, he will be equipped for manipulating rope for all practical farm
purposes.
A^/>Ars o/^ P^ffTs o/^ /Po/^e
ni^.
5/MPL OR Ot/e/?H/)A/D ^fl/or.
F/6U/? E/6/iTH/^OT Srei^EOORe Ka/ot.
Plato 1.
3QUARe Knot. 5nET Bend.
Carrich Bend- B^ANNr H/vor.
Plate 2
Sl/p/Ovot. A/A/vae/f Knot.
Bowl/NeKnot, Te/^MsTE/?3 /C/vo T.
Plate 3
129
DouBLeFifM/sH Loop. DouBteBo/^/C/voT.
5/ii:PS/f/>NK. Cats Paw-
Plate 4
HaltHitch
TiMge/?H/TcM.
Clo^e Hitch.
CoMBMeO 7l/^3/r'/^W /iAi/'H/TC/f.
Plate :
130
/?OLUN6 H/TCH- Bi/tc/fyy/iii H/Tt/i.
/?OUND Tb/fN /i/^O /i/)l/=NiTC/i.
FiSHe/?MA/^j Bs/iO.
Plate 6
RuNNiNSHircH. ^/^/?6fA/Cr/(/VOT
BoiYUNf O/V TN B/6MT. 3lippe/^rRee^K/fOT.
Plate 7
131
Ci/cKOLO'5 /Ksr,f
:
3c//r&OAiJs K/vor.
SHeerSE/vD tv/TH 7bi>oif. Wmipping.
Plate 8
W/)uf<mr.
n^^
WallK/vorCmw/if.
ffed.
M/iTrtew l4^L/f/<:
M/ir/yfyt' yy/ii/rf/?.
F/^S F/e'^.
132
3HO/n-^/'uc; Commenced. Sf/o/frSfuce,
^- Pai/f/on.
5mo/?tJpi/c. J-'^Poj///o/7. 5/fo/?rSfuce, Comp/efe(^.
Plate 10
Lor^G Splice, Commenced. Long Splice,
2
-"^ Position
Lo/ve Splice
, J -Position Long Splice, Completed.
', stflp ends and
strand around its mate.
Plate 11
133
134
135
Combination I'lic r.
136
Ratchet Brace.
Coping Saw.
Drawing Knife.
Ro.se Countersink Set Twist Drill Bits.
Combination Carborundum Stone.
Saw Set
Flat Bastard Mill Vi\r
Slim Taper Triangular File.
^i$^^0=
Auger Bit.
Putty Knife.
137