8/7/2014 5:29:10 PM Parameters and Signals (ACS550/204c) Page: 1

Name Value Unit Min Max

99 START-UP DATA
01 LANGUAGE ENGLISH 0 16
02 APPLIC MACRO ABB STANDARD -3 8
04 MOTOR CTRL MODE VECTOR:SPEED 1 3
05 MOTOR NOM VOLT 380 V 200 600
06 MOTOR NOM CURR 57.6 A 8.8 88
07 MOTOR NOM FREQ 50 Hz 10 500
08 MOTOR NOM SPEED 1460 rpm 50 30000
09 MOTOR NOM POWER 30 kW 4.4 66
10 ID RUN OFF/IDMAGN 0 1

1 OPERATING DATA
02 SPEED 0 rpm 0 30000
03 OUTPUT FREQ 0 Hz 0 500
04 CURRENT 0 A 0 88
05 TORQUE 0 % -200 200
06 POWER 0 kW -44 44
07 DC BUS VOLTAGE 603 V 0 1000
09 OUTPUT VOLTAGE 0 V 0 800
10 DRIVE TEMP 26.9 C 0 150
11 EXTERNAL REF 1 2 rpm 0 30000
12 EXTERNAL REF 2 0.1 % 0 600
13 CTRL LOCATION EXT1 0 2
14 RUN TIME (R) 5132 h 0 10000
15 KWH COUNTER (R) 49650 kWh 0 9999
16 APPL BLK OUTPUT 0.1 % 0 600
18 DI 1-3 STATUS 0 0 7
19 DI 4-6 STATUS 0 0 7
20 AI 1 0.1 % 0 100
21 AI 2 0.1 % 0 100
22 RO 1-3 STATUS 0 0 7
23 RO 4-6 STATUS 0 0 7
24 AO 1 0 mA 0 20
25 AO 2 0 mA 0 20
26 PID 1 OUTPUT 0 % 0 100
27 PID 2 OUTPUT 0 % 0 100
28 PID 1 SETPNT 0 % 0 100
29 PID 2 SETPNT 0 % 0 100
30 PID 1 FBK 0 % 0 100
31 PID 2 FBK 0 % 0 100
32 PID 1 DEVIATION 0 % -100 100
33 PID 2 DEVIATION 0 % -100 100
34 COMM RO WORD 0 0 65535
35 COMM VALUE 1 0 -32768 32767
36 COMM VALUE 2 0 -32768 32767
37 PROCESS VAR 1 0 rpm 0 30000
38 PROCESS VAR 2 0 A 0 88
39 PROCESS VAR 3 0 Hz 0 500
40 RUN TIME 55.13 kh 0 500
41 MWH COUNTER 377 MWh 0 9999
42 REVOLUTION CNTR 4320 Mrev 0 65535
43 DRIVE ON TIME HI 2722 d 0 65535
44 DRIVE ON TIME LO 09:01:48 0 43200
45 MOTOR TEMP 0 0 0
46 MECH ANGLE 0 0 65535
47 MECH REVS 0 -32768 32767
48 Z PLS DETECTED NOT DETECTED 0 1

3 FB ACTUAL SIGNALS
Drie!ind"# $ig%t &ersi"n 2'7 A(( )*
C:+,sers+D-./ 0/).1 .AM+Des2t"3+ACS550 4 Sa* c5m 14 PM147814'd#3
8/7/2014 5:29:10 PM Parameters and Signals (ACS550/204c) Page: 2
01 FB CMD WORD 1 3041 0 65535
02 FB CMD WORD 2 C 0 65535
03 FB STS WORD 1 8010 0 65535
04 FB STS WORD 2 14 0 65535
05 FAULT WORD 1 2000 0 65535
06 FAULT WORD 2 0 0 65535
07 FAULT WORD 3 0 0 65535
08 ALARM WORD 1 0 0 65535
09 ALARM WORD 2 0 0 65535

4 FAULT HISTORY
01 LAST FAULT EXT FAULT 1 0 65535
02 FAULT TIME 1 2722 d 0 65535
03 FAULT TIME 2 08:59:44 0 65535
04 SPEED AT FLT 0 rpm -32768 32767
05 FREQ AT FLT 0 Hz -3276.8 3276.7
06 VOLTAGE AT FLT 0 V 0 6553.5
07 CURRENT AT FLT 0 A 0 6553.5
08 TORQUE AT FLT 0 % -3276.8 3276.7
09 STATUS AT FLT 0 0 65535
10 DI 1-3 AT FLT 0 0 65535
11 DI 4-6 AT FLT 0 0 65535
12 PREVIOUS FAULT 1 EXT FAULT 1 0 65535
13 PREVIOUS FAULT 2 EXT FAULT 1 0 65535

10 START/STOP/DIR
01 EXT1 COMMANDS DI1 0 14
02 EXT2 COMMANDS NOT SEL 0 14
03 DIRECTION FORWARD 1 3

11 REFERENCE SELECT
01 KEYPAD REF SEL REF1(Hz/rpm) 1 2
02 EXT1/EXT2 SEL EXT1 -6 12
03 REF1 SELECT AI1 0 17
04 REF1 MIN 0 rpm 0 30000
05 REF1 MAX 1650 rpm 0 30000
06 REF2 SELECT AI2 0 19
07 REF2 MIN 0 % 0 100
08 REF2 MAX 100 % 0 100

12 CONSTANT SPEEDS
01 CONST SPEED SEL NOT SEL -14 19
02 CONST SPEED 1 300 rpm 0 30000
03 CONST SPEED 2 600 rpm 0 30000
04 CONST SPEED 3 900 rpm 0 30000
05 CONST SPEED 4 1200 rpm 0 30000
06 CONST SPEED 5 1500 rpm 0 30000
07 CONST SPEED 6 2400 rpm 0 30000
08 CONST SPEED 7 3000 rpm 0 30000
09 TIMED MODE SEL CS1/2/3/4 1 2

13 ANALOGUE INPUTS
01 MINIMUM AI1 0 % 0 100
02 MAXIMUM AI1 100 % 0 100
03 FILTER AI1 0.1 s 0 10
04 MINIMUM AI2 0 % 0 100
05 MAXIMUM AI2 100 % 0 100
06 FILTER AI2 0.1 s 0 10

14 RELAY OUTPUTS
01 RELAY OUTPUT 1 RUN 0 45
02 RELAY OUTPUT 2 RUN 0 45
Drie!ind"# $ig%t &ersi"n 2'7 A(( )*
C:+,sers+D-./ 0/).1 .AM+Des2t"3+ACS550 4 Sa* c5m 14 PM147814'd#3
8/7/2014 5:29:10 PM Parameters and Signals (ACS550/204c) Page: 6
03 RELAY OUTPUT 3 FAULT(-1) 0 45
04 RO 1 ON DELAY 0 s 0 3600
05 RO 1 OFF DELAY 0 s 0 3600
06 RO 2 ON DELAY 0 s 0 3600
07 RO 2 OFF DELAY 0 s 0 3600
08 RO 3 ON DELAY 0 s 0 3600
09 RO 3 OFF DELAY 0 s 0 3600
10 RELAY OUTPUT 4 NOT SEL 0 45
11 RELAY OUTPUT 5 NOT SEL 0 45
12 RELAY OUTPUT 6 NOT SEL 0 45
13 RO 4 ON DELAY 0 s 0 3600
14 RO 4 OFF DELAY 0 s 0 3600
15 RO 5 ON DELAY 0 s 0 3600
16 RO 5 OFF DELAY 0 s 0 3600
17 RO 6 ON DELAY 0 s 0 3600
18 RO 6 OFF DELAY 0 s 0 3600

15 ANALOGUE OUTPUTS
01 AO1 CONTENT SEL EXT REF 1 99 199
02 AO1 CONTENT MIN 0 Hz 0 6553.5
03 AO1 CONTENT MAX 150 Hz 0 6553.5
04 MINIMUM AO1 0 mA 0 20
05 MAXIMUM AO1 20 mA 0 20
06 FILTER AO1 0.1 s 0 10
07 AO2 CONTENT SEL TORQUE 99 199
08 AO2 CONTENT MIN 0 % -3276.8 3276.7
09 AO2 CONTENT MAX 100 % -3276.8 3276.7
10 MINIMUM AO2 0 mA 0 20
11 MAXIMUM AO2 20 mA 0 20
12 FILTER AO2 0.1 s 0 10

16 SYSTEM CONTROLS
01 RUN ENABLE DI3 -6 7
02 PARAMETER LOCK OPEN 0 2
03 PASS CODE 0 0 65535
04 FAULT RESET SEL KEYPAD -6 8
05 USER PAR SET CHG NOT SEL -6 6
06 LOCAL LOCK NOT SEL -6 8
07 PARAM SAVE DONE 0 1
08 START ENABLE 1 NOT SEL -6 7
09 START ENABLE 2 NOT SEL -6 7
10 DISPLAY ALARMS NO 0 1

20 LIMITS
01 MINIMUM SPEED 0 rpm -30000 30000
02 MAXIMUM SPEED 1640 rpm 0 30000
03 MAX CURRENT 79.2 A 0 79.2
05 OVERVOLT CTRL ENABLE 0 1
06 UNDERVOLT CTRL ENABLE(TIME) 0 2
07 MINIMUM FREQ 0 Hz -500 500
08 MAXIMUM FREQ 55 Hz 0 500
13 MIN TORQUE SEL MIN TORQUE 1 -6 7
14 MAX TORQUE SEL MAX TORQUE 1 -6 7
15 MIN TORQUE 1 -5 % -600 0
16 MIN TORQUE 2 -300 % -600 0
17 MAX TORQUE 1 100 % 0 600
18 MAX TORQUE 2 300 % 0 600

21 START/STOP
01 START FUNCTION DC MAGN 1 2
02 STOP FUNCTION RAMP 1 2
03 DC MAGN TIME 0.3 s 0 10
Drie!ind"# $ig%t &ersi"n 2'7 A(( )*
C:+,sers+D-./ 0/).1 .AM+Des2t"3+ACS550 4 Sa* c5m 14 PM147814'd#3
8/7/2014 5:29:10 PM Parameters and Signals (ACS550/204c) Page: 4
04 DC HOLD CTL NOT SEL 0 2
05 DC HOLD SPEED 5 rpm 0 360
06 DC CURR REF 30 % 0 100
07 DC BRAKE TIME 0 s 0 250
08 START INHIBIT OFF 0 1
09 EMERG STOP SEL NOT SEL -6 6
10 TORQ BOOST CURR 100 % 15 300

22 ACCEL/DECEL
01 ACC/DEC 1/2 SEL DI5 -6 7
02 ACCELER TIME 1 50 s 0 1800
03 DECELER TIME 1 50 s 0 1800
04 RAMP SHAPE 1 LINEAR s 0 1000
05 ACCELER TIME 2 60 s 0 1800
06 DECELER TIME 2 60 s 0 1800
07 RAMP SHAPE 2 LINEAR s 0 1000
08 EMERG DEC TIME 1 s 0 1800
09 RAMP INPUT 0 NOT SEL -6 7

23 SPEED CONTROL
01 PROP GAIN 10 0 200
02 INTEGRATION TIME 2.5 s 0 600
03 DERIVATION TIME 0 ms 0 10000
04 ACC COMPENSATION 0 s 0 600
05 AUTOTUNE RUN OFF 0 1

24 TORQUE CONTROL
01 TORQ RAMP UP 0 s 0 120
02 TORQ RAMP DOWN 0 s 0 120

25 CRITICAL SPEEDS
01 CRIT SPEED SEL OFF 0 1
02 CRIT SPEED 1 LO 0 rpm 0 30000
03 CRIT SPEED 1 HI 0 rpm 0 30000
04 CRIT SPEED 2 LO 0 rpm 0 30000
05 CRIT SPEED 2 HI 0 rpm 0 30000
06 CRIT SPEED 3 LO 0 rpm 0 30000
07 CRIT SPEED 3 HI 0 rpm 0 30000

26 MOTOR CONTROL
01 FLUX OPT ENABLE OFF 0 1
02 FLUX BRAKING OFF 0 1
03 IR COMP VOLT 4.9 V 0 100
04 IR COMP FREQ 80 % 0 100
05 U/F RATIO LINEAR 1 2
06 SWITCHING FREQ 4 kHz 0 0
07 SWITCH FREQ CTRL ON 0 1
08 SLIP COMP RATIO 0 % 0 200
09 NOISE SMOOTHING DISABLE 0 1

29 MAINTENANCE TRIG
01 COOLING FAN TRIG 0 kh 0 6553.5
02 COOLING FAN ACT 0 kh 0 6553.5
03 REVOLUTION TRIG 0 Mrev 0 65535
04 REVOLUTION ACT 0 Mrev 0 65535
05 RUN TIME TRIG 0 kh 0 6553.5
06 RUN TIME ACT 0 kh 0 6553.5
07 USER MWh TRIG 0 MWh 0 6553.5
08 USER MWh ACT 0 MWh 0 6553.5

30 FAULT FUNCTIONS
01 AI<MIN FUNCTION NOT SEL 0 3
Drie!ind"# $ig%t &ersi"n 2'7 A(( )*
C:+,sers+D-./ 0/).1 .AM+Des2t"3+ACS550 4 Sa* c5m 14 PM147814'd#3
8/7/2014 5:29:10 PM Parameters and Signals (ACS550/204c) Page: 5
02 PANEL COMM ERR FAULT 1 3
03 EXTERNAL FAULT 1 DI2(INV) -6 6
04 EXTERNAL FAULT 2 NOT SEL -6 6
05 MOT THERM PROT FAULT 0 2
06 MOT THERM TIME 500 s 256 9999
07 MOT LOAD CURVE 100 % 50 150
08 ZERO SPEED LOAD 70 % 25 150
09 BREAK POINT FREQ 35 Hz 1 250
10 STALL FUNCTION NOT SEL 0 2
11 STALL FREQUENCY 20 Hz 0.5 50
12 STALL TIME 20 s 10 400
13 UNDERLOAD FUNC NOT SEL 0 2
14 UNDERLOAD TIME 20 s 10 400
15 UNDERLOAD CURVE 1 1 5
17 EARTH FAULT DISABLE 0 1
18 COMM FAULT FUNC NOT SEL 0 3
19 COMM FAULT TIME 3 s 0 60
21 AI1 FAULT LIMIT 0 % 0 100
22 AI2 FAULT LIMIT 0 % 0 100
23 WIRING FAULT ENABLE 0 1

31 AUTOMATIC RESET
01 NUMBER OF TRIALS 0 0 5
02 TRIAL TIME 30 s 1 600
03 DELAY TIME 0 s 0 120
04 AR OVERCURRENT DISABLE 0 1
05 AR OVERVOLTAGE DISABLE 0 1
06 AR UNDERVOLTAGE DISABLE 0 1
07 AR AI<MIN DISABLE 0 1
08 AR EXTERNAL FLT DISABLE 0 1

32 SUPERVISION
01 SUPERV 1 PARAM OUTPUT FREQ 101 199
02 SUPERV 1 LIM LO 50 Hz 0 6553.5
03 SUPERV 1 LIM HI 50 Hz 0 6553.5
04 SUPERV 2 PARAM CURRENT 101 199
05 SUPERV 2 LIM LO 44 A 0 352
06 SUPERV 2 LIM HI 44 A 0 352
07 SUPERV 3 PARAM TORQUE 101 199
08 SUPERV 3 LIM LO 100 % -3276.8 3276.7
09 SUPERV 3 LIM HI 100 % -3276.8 3276.7

33 INFORMATION
01 FIRMWARE 204C 8268 8268
02 LOADING PACKAGE 1005 4101 4101
03 TEST DATE 5.21 0 655.35
04 DRIVE RATING 594 0 65535

34 PANEL DISPLAY
01 SIGNAL1 PARAM SPEED 100 199
02 SIGNAL1 MIN 0 rpm 0 65535
03 SIGNAL1 MAX 30000 rpm 0 65535
04 OUTPUT1 DSP FORM DIRECT 0 9
05 OUTPUT1 UNIT rpm 0 127
06 OUTPUT1 MIN 0 rpm 0 65535
07 OUTPUT1 MAX 30000 rpm 0 65535
08 SIGNAL2 PARAM CURRENT 100 199
09 SIGNAL2 MIN 0 A 0 352
10 SIGNAL2 MAX 88 A 0 352
11 OUTPUT2 DSP FORM DIRECT 0 9
12 OUTPUT2 UNIT A 0 127
13 OUTPUT2 MIN 0 A 0 6553.5
Drie!ind"# $ig%t &ersi"n 2'7 A(( )*
C:+,sers+D-./ 0/).1 .AM+Des2t"3+ACS550 4 Sa* c5m 14 PM147814'd#3
8/7/2014 5:29:10 PM Parameters and Signals (ACS550/204c) Page: 7
14 OUTPUT2 MAX 88 A 0 6553.5
15 SIGNAL3 PARAM OUTPUT FREQ 100 199
16 SIGNAL3 MIN 0 Hz 0 6553.5
17 SIGNAL3 MAX 500 Hz 0 6553.5
18 OUTPUT3 DSP FORM DIRECT 0 9
19 OUTPUT3 UNIT Hz 0 127
20 OUTPUT3 MIN 0 Hz 0 6553.5
21 OUTPUT3 MAX 500 Hz 0 6553.5

35 MOTOR TEMP MEAS
01 SENSOR TYPE NONE 0 6
02 INPUT SELECTION AI1 1 8
03 ALARM LIMIT 0 0 0
04 FAULT LIMIT 0 0 0

36 TIMED FUNCTIONS
01 TIMERS ENABLE NOT SEL -6 7
02 START TIME 1 00:00:00 0 43199
03 STOP TIME 1 00:00:00 0 43199
04 START DAY 1 MONDAY 1 7
05 STOP DAY 1 MONDAY 1 7
06 START TIME 2 00:00:00 0 43199
07 STOP TIME 2 00:00:00 0 43199
08 START DAY 2 MONDAY 1 7
09 STOP DAY 2 MONDAY 1 7
10 START TIME 3 00:00:00 0 43199
11 STOP TIME 3 00:00:00 0 43199
12 START DAY 3 MONDAY 1 7
13 STOP DAY 3 MONDAY 1 7
14 START TIME 4 00:00:00 0 43199
15 STOP TIME 4 00:00:00 0 43199
16 START DAY 4 MONDAY 1 7
17 STOP DAY 4 MONDAY 1 7
22 BOOSTER SEL NOT SEL -6 6
23 BOOSTER TIME 00:00:00 0 43199
26 TIMED FUNC 1 SRC NOT SEL 0 31
27 TIMED FUNC 2 SRC NOT SEL 0 31
28 TIMED FUNC 3 SRC NOT SEL 0 31
29 TIMED FUNC 4 SRC NOT SEL 0 31

40 PROCESS PID SET 1
01 GAIN 1 0.1 100
02 INTEGRATION TIME 60 s 0 3600
03 DERIVATION TIME 0 s 0 10
04 PID DERIV FILTER 1 s 0 10
05 ERROR VALUE INV NO 0 1
06 UNITS % 0 255
07 UNIT SCALE 1 0 4
08 0% VALUE 0 % -3276.8 3276.7
09 100% VALUE 100 % -3276.8 3276.7
10 SET POINT SEL AI1 0 19
11 INTERNAL SETPNT 40 % -3276.8 3276.7
12 SETPOINT MIN 0 % -500 500
13 SETPOINT MAX 100 % -500 500
14 FBK SEL ACT1 1 10
15 FBK MULTIPLIER 0 -33 33
16 ACT1 INPUT AI2 1 5
17 ACT2 INPUT AI2 1 5
18 ACT1 MINIMUM 0 % -1000 1000
19 ACT1 MAXIMUM 100 % -1000 1000
20 ACT2 MINIMUM 0 % -1000 1000
21 ACT2 MAXIMUM 100 % -1000 1000
Drie!ind"# $ig%t &ersi"n 2'7 A(( )*
C:+,sers+D-./ 0/).1 .AM+Des2t"3+ACS550 4 Sa* c5m 14 PM147814'd#3
8/7/2014 5:29:10 PM Parameters and Signals (ACS550/204c) Page: 7
22 SLEEP SELECTION NOT SEL -6 7
23 PID SLEEP LEVEL 0 rpm 0 30000
24 PID SLEEP DELAY 60 s 0 3600
25 WAKE-UP DEV 0 % 0 3276.7
26 WAKE-UP DELAY 0.5 s 0 60
27 PID 1 PARAM SET SET 1 -6 11

41 PROCESS PID SET 2
01 GAIN 1 0.1 100
02 INTEGRATION TIME 60 s 0 3600
03 DERIVATION TIME 0 s 0 10
04 PID DERIV FILTER 1 s 0 10
05 ERROR VALUE INV NO 0 1
06 UNITS % 0 255
07 UNIT SCALE 1 0 4
08 0% VALUE 0 % -3276.8 3276.7
09 100% VALUE 100 % -3276.8 3276.7
10 SET POINT SEL AI1 0 19
11 INTERNAL SETPNT 40 % -3276.8 3276.7
12 SETPOINT MIN 0 % -500 500
13 SETPOINT MAX 100 % -500 500
14 FBK SEL ACT1 1 10
15 FBK MULTIPLIER 0 -33 33
16 ACT1 INPUT AI2 1 5
17 ACT2 INPUT AI2 1 5
18 ACT1 MINIMUM 0 % -1000 1000
19 ACT1 MAXIMUM 100 % -1000 1000
20 ACT2 MINIMUM 0 % -1000 1000
21 ACT2 MAXIMUM 100 % -1000 1000
22 SLEEP SELECTION NOT SEL -6 7
23 PID SLEEP LEVEL 0 rpm 0 30000
24 PID SLEEP DELAY 60 s 0 3600
25 WAKE-UP DEV 0 % 0 3276.7
26 WAKE-UP DELAY 0.5 s 0 60

42 EXT / TRIM PID
01 GAIN 1 0.1 100
02 INTEGRATION TIME 60 s 0 3600
03 DERIVATION TIME 0 s 0 10
04 PID DERIV FILTER 1 s 0 10
05 ERROR VALUE INV NO 0 1
06 UNITS % 0 255
07 UNIT SCALE 1 0 4
08 0% VALUE 0 % -3276.8 3276.7
09 100% VALUE 100 % -3276.8 3276.7
10 SET POINT SEL AI1 0 19
11 INTERNAL SETPNT 40 % -3276.8 3276.7
12 SETPOINT MIN 0 % -500 500
13 SETPOINT MAX 100 % -500 500
14 FBK SEL ACT1 1 10
15 FBK MULTIPLIER 0 -33 33
16 ACT1 INPUT AI2 1 5
17 ACT2 INPUT AI2 1 5
18 ACT1 MINIMUM 0 % -1000 1000
19 ACT1 MAXIMUM 100 % -1000 1000
20 ACT2 MINIMUM 0 % -1000 1000
21 ACT2 MAXIMUM 100 % -1000 1000
28 ACTIVATE NOT SEL -6 12
29 OFFSET 0 % 0 100
30 TRIM MODE NOT SEL 0 2
31 TRIM SCALE 0 % -100 100
32 CORRECTION SRC PID2REF 1 2
Drie!ind"# $ig%t &ersi"n 2'7 A(( )*
C:+,sers+D-./ 0/).1 .AM+Des2t"3+ACS550 4 Sa* c5m 14 PM147814'd#3
8/7/2014 5:29:10 PM Parameters and Signals (ACS550/204c) Page: 8

50 ENCODER
01 PULSE NR 1024 50 16384
02 ENCODER ENABLE DISABLE 0 1
03 ENCODER FAULT FAULT 1 2
10 Z PLS ENABLE DISABLE 0 1
11 POSITION RESET DISABLE 0 1

51 EXT COMM MODULE
01 FBA TYPE NOT DEFINED 0 65535
02 FBA PAR 2 0 0 65535
03 FBA PAR 3 0 0 65535
04 FBA PAR 4 0 0 65535
05 FBA PAR 5 0 0 65535
06 FBA PAR 6 0 0 65535
07 FBA PAR 7 0 0 65535
08 FBA PAR 8 0 0 65535
09 FBA PAR 9 0 0 65535
10 FBA PAR 10 0 0 65535
11 FBA PAR 11 0 0 65535
12 FBA PAR 12 0 0 65535
13 FBA PAR 13 0 0 65535
14 FBA PAR 14 0 0 65535
15 FBA PAR 15 0 0 65535
16 FBA PAR 16 0 0 65535
17 FBA PAR 17 0 0 65535
18 FBA PAR 18 0 0 65535
19 FBA PAR 19 0 0 65535
20 FBA PAR 20 0 0 65535
21 FBA PAR 21 0 0 65535
22 FBA PAR 22 0 0 65535
23 FBA PAR 23 0 0 65535
24 FBA PAR 24 0 0 65535
25 FBA PAR 25 0 0 65535
26 FBA PAR 26 0 0 65535
27 FBA PAR REFRESH DONE 0 1
28 FILE CPI FW REV 0 0 65535
29 FILE CONFIG ID 0 0 65535
30 FILE CONFIG REV 0 0 65535
31 FBA STATUS IDLE 0 6
32 FBA CPI FW REV 0 0 65535
33 FBA APPL FW REV 0 0 65535

52 PANEL COMM
01 STATION ID 1 1 247
02 BAUD RATE 96 0 0
03 PARITY 8 NONE 1 0 3
04 OK MESSAGES 43923 0 65535
05 PARITY ERRORS 702 0 65535
06 FRAME ERRORS 0 0 65535
07 BUFFER OVERRUNS 0 0 65535
08 CRC ERRORS 90 0 65535

53 EFB PROTOCOL
01 EFB PROTOCOL ID 112 0 65535
02 EFB STATION ID 1 0 65535
03 EFB BAUD RATE 96 0 0
04 EFB PARITY 8 NONE 2 0 3
05 EFB CTRL PROFILE ABB DRV LIM 0 2
06 EFB OK MESSAGES 0 0 65535
07 EFB CRC ERRORS 0 0 65535
08 EFB UART ERRORS 33702 0 65535
Drie!ind"# $ig%t &ersi"n 2'7 A(( )*
C:+,sers+D-./ 0/).1 .AM+Des2t"3+ACS550 4 Sa* c5m 14 PM147814'd#3
8/7/2014 5:29:10 PM Parameters and Signals (ACS550/204c) Page: 9
09 EFB STATUS IDLE 0 7
10 EFB PAR 10 103 0 65535
11 EFB PAR 11 104 0 65535
12 EFB PAR 12 0 0 65535
13 EFB PAR 13 0 0 65535
14 EFB PAR 14 0 0 65535
15 EFB PAR 15 0 0 65535
16 EFB PAR 16 0 0 65535
17 EFB PAR 17 0 0 65535
18 EFB PAR 18 0 0 65535
19 EFB PAR 19 0 0 65535
20 EFB PAR 20 208 0 65535

81 PFC CONTROL
03 REFERENCE STEP 1 0 % 0 100
04 REFERENCE STEP 2 0 % 0 100
05 REFERENCE STEP 3 0 % 0 100
09 START FREQ 1 50 Hz 0 500
10 START FREQ 2 50 Hz 0 500
11 START FREQ 3 50 Hz 0 500
12 LOW FREQ 1 25 Hz 0 500
13 LOW FREQ 2 25 Hz 0 500
14 LOW FREQ 3 25 Hz 0 500
15 AUX MOT START D 5 s 0 3600
16 AUX MOT STOP D 3 s 0 3600
17 NR OF AUX MOT 1 0 4
18 AUTOCHNG INTERV NOT SEL h 0 336
19 AUTOCHNG LEVEL 50 % 0 100
20 INTERLOCKS DI4 0 6
21 REG BYPASS CTRL NO 0 1
22 PFC START DELAY 0.5 s 0 10
23 PFC ENABLE NOT SEL 0 1
24 ACC IN AUX STOP NOT SEL s 0 1800
25 DEC IN AUX START NOT SEL s 0 1800
26 TIMED AUTOCHNG NOT SEL 0 4
27 MOTORS 2 1 7

98 OPTIONS
02 COMM PROT SEL STD MODBUS 0 4
Drie!ind"# $ig%t &ersi"n 2'7 A(( )*
C:+,sers+D-./ 0/).1 .AM+Des2t"3+ACS550 4 Sa* c5m 14 PM147814'd#3