PPeettrroolleeuum

m && C
Cooaall
IISSN 1337-7027
Available online at www.vurup.sk/pc
Petroleum & Coal 48 (2), 15-23, 2006

MODELING AND SIMULATION OF AMMONIA SYNTHESIS

REACTOR
Ali Dashti, Kayvan Khorsand1, Mehdi Ahmadi Marvast, Madjid Kakavand
Research Institute of Petroleum Industry (RIPI), Pazhouheshgah Blvd.,
Khairabad, Qom Road, Tehran, Iran.
1
corresponding author, [email protected]
Received May 1, 2006; accepted June 24, 2006

Abstract
In this paper an industrial ammonia synthesis reactor has been modeled. The reactor under study is of horizontal
type. This reactor which is under the license of Kellogg Company is equipped with three axial flow catalyst beds
and an internal heat exchanger in accompany with a cooling flow. The achieved modeling is one dimensional and
non-homogenous. Considering the sever effect of internal heat exchanger on reactor operation, it has been
simulated by calculation of film heat transfer coefficients in its tube and shell and then, taking into account the
shell thermal resistance and fouling coefficient, obtaining the overall heat transfer coefficient. So in the developed
software, the heat transfer coefficient is first calculated using the conditions of the input flow to the exchanger and
then the input flows to the first and second beds are calculated. The differential equations have been solved
using Rung Kutta 4 method and the results have been compared with the available industrial data. Finally the
capability of the developed software for industrial application has been investigated by changing the reactor
operation conditions and studying their effects on reactor output.
Key words: ammonia, reactor, modeling, simulation

1. Introduction
Ammonia Synthesis is a very important process in chemical complexes. Ammonia is the initial
chemical material for a variety of industries. It is used in production of chemical fertilizers, explosive
materials, polymers, acids and even coolers. Simulation can play an important role to give an insight
of the industrial units and hence simulation of Ammonia unit is very important to help us investigate
the different operation modes of this unit and optimize that. Ammonia synthesis loop is the most
important part of this unit which better understanding of its bottleneck can led us to make the
operation yield higher than before.
2. Ammonia Synthesis Loop
In ammonia production unit, the synthesis loop is located after the syngas production and
purification units. Ammonia synthesis process takes place in high pressure and hence high power
multi cycle compressors are used to supply the required pressure. The Kellogg synthesis reactor
incorporated in this loop is of horizontal type with three beds. To control the temperature between first
and second beds, an internal heat exchanger has been used in which the input feed to the first bed
and the output gas from the same bed have thermal exchange. In addition to the mentioned heat
exchanger, the quench gas flow is also used for control of temperature. The input feed to the reactor,
is first divided into two parts, before entrance. One part is considered as feed and the other part as
quench gas. The feed, after entering the reactor, passes through the empty spaces of the beds as
well as the reactor walls and gets slightly heated. When reaching to the end of the reactor, it passes
through the shell of the internal heat exchanger and its temperature reaches 400 C. Tubes of the
heat exchanger contain the output gas from the first bed. Quench gas is used to control the inlet
temperature of the first bed. The required temperature for inlet of the first bed is 371 C. Output gas,

Ali Dashti et al./Petroleum & Coal 48(2) 15-23 (2006)

16

after warming up, is then entered to first catalytic bed. Figure 1 depicts the schematic diagram of a
Kellogg horizontal reactor.

Fig.1 Ammonia Synthesis Reactor - Kellogg method [1]

When the gas passes the first bed and the reaction is taken place, its temperature increases and
reaches 496 C. It then enters the tubes of the heat exchanger to cool down. Gas is then entered from
top of the second bed. Temperature rises again as the reaction takes place in the second bed. No
specific operation is carried out between beds two and three. In fact these two beds act as a single
bed whose length is twice the length of each bed. The catalyst of this reactor is magnetic ferro oxide.
3. Mathematical Model
By modeling of the synthesis reactor, temperature, concentrations and pressure profiles are
obtained. Of course testing of the model based on the above parameters is achieved at the end of
each bed as industrial data are not usually available along the length of the bed. The following
assumptions have been made for this modeling:
1. One-dimensional Cartesian coordinate has been considered along with the bulk flow.
2. Penetration of mass and heat is ignored, as the fluid velocity is very high in industrial scale.
3. Density is constant
4. Concentration and temperature on catalyst surface and bulk of gas are equal.
5. The effects of penetration resistance in catalyst, temperature gradient and catalyst inside
concentration have been incorporated in the equations by a coefficient.
[2,3]

Material balance (Molar)

Considering an element with height of x and cross section area equal to that of the bed well have:

uCA x

uCA x+x
Accumulation = Consumption Production + Output Input
There shall be no accumulation as the system has been considered to be in steady state.

uCA x uCA x + x + Ax rNH 3 = 0

Dividing both sides of the equation by Ax and x 0, well have:

Ali Dashti et al./Petroleum & Coal 48(2) 15-23 (2006)

dc
+ rNH3 = 0
dx

17

This equation can be re-written as below based on the Nitrogen Conversion Percentage shown by Z:

dZ rNH 3
=
FN
dx
2 2
A

in which the term

FN2

is the initial molar flow of N2.

Reaction Rate [3,4,5,6,7,8]

To calculate the rate of reaction, modified Temkin equation offered by Dyson & Simon in 1968 has
been used [4]

RNH 3

a H3 2
2

= 2k K a a N 2 2
a NH

2
a NH
3

a H3
2

in which
: Constant which takes a value from 0.5 to 0.75 in literature [8].
k : Rate constant for reverse reaction in: N 2 + 3H 2 2 NH 3

K a : equilibrium constant
ai : Activity
Activation can be written in terms of activation coefficient as below:

ai =

fi
f i

f i 0 : Reference fugacity. If the reference fugacity is considered to be 1 atm, then:

ai =

fi
= f i = yii P
1

In this equation

is the fugacity coefficient and P is the total pressure.

Below equations are the experimental ones for fugacity coefficient of hydrogen, nitrogen and
ammonia [4].

P
(3.8402T 0.125 +0.541)

(
( 0.011901T 5.941)
0.1263T 0.5 15.98 ) 2
300
e

Pe
P + 300 e
= expe

N = 0.93431737 + 0.2028538 10 3 T + 0.295896 10 3 P

2

0.270727 10 6 T 2 + 0.4775207 10 6 P 2
NH3 = 0.1438996 + 0.2028538 10 2 T 0.4487672 10 3 P
5

0.1142945 10 T + 0.2761216 10 P
2

Ali Dashti et al./Petroleum & Coal 48(2) 15-23 (2006)

18

In above equations T is in terms of Kelvin and P in terms of atmosphere.

The equation of reverse ammonia synthesis reaction has been considered in base of Arrhenius
format.

E
k = k exp

RT
k : Arrhenius coefficient equal to 8.849 1014

10

E : Activation energy, which varies with temperature. Its mean value is 40765

kcal
kmol

R : Gas constant
In 1930, Gillespie and Beattie have developed the following equation to calculate the equilibrium
constant [9].

log K a = 2.691122 log T 5051925 10 5 T + 1.848863 10 7 T 2

+

11

2001.6
+ 2.689
T

Effect Factor[3,4,10]
To investigate the effects of temperature and density of the catalyst interior and the difference
between these parameters with those of the catalyst surface, an effect factor called has been
defined. The general form of the equation defining this effect factor has been given below [10].

= b + b1T + b2 Z + b3T 2 + b4 Z 2 + b5T 3 + b6 Z 3

12

The above equation is in terms of T and conversion percentage. The coefficients of this equation for
three different pressures have been depicted in table 3 [4].

Table 3. Coefficients of the correction factor polynomial in terms of pressure

Pressure
(bar)

150
225
300

-17.539096
-8.2125534
-4.6757259

b2

b3

b4

b5

b6

6.900548
6.190112
4.687353

-1.08279e-4
-5.354571e-5
-3.463308e-5

-26.42469
-20.86963
-11.28031

4.927648e-8
2.379142e-8
1.540881e-8

38.937
27.88
10.46

b1
0.07697849
0.03774149
0.02354872

Energy balance
Energy balance is investigated on the same element on which mass balance has been considered.
Accumulation = Consumed Energy Produced Energy + Output Energy Input Energy
In steady state, the accumulation is zero.

A uC pT x uC pT

x + x

}+ Ax( H )R
r

=0

NH 3

13

Dividing the above equation by Ax and x 0, well have:

uC p

dT
+ ( H r )RNH 3 = 0
dx

Heat Capacitance
The following equation is used to determine the Heat capacitance:

14

Ali Dashti et al./Petroleum & Coal 48(2) 15-23 (2006)

C pi = 4.184(ai = biT + ciT 2 + d iT 3 )

19

kj

kmol

15

Table 4. Coefficients of Cp polynomial for some component.

Component

b 10 2

c 10 5

H2
N2
CH4
Argon

6.952
6.903
4.75
4.9675

-0.04567
-0.03753
1.2
----

0.09563
0.193
0.303
----

d 10 5
-0.2079
-0.6861
-2.63
----

In 1967, Shah has developed an equation for determination of ammonia heat capacity which has
been used in our modeling [11,12].

C PNH 3

6.5846 0.61251 10 2 T + 0.23663 10 5 T 2

9 3
1.5981 10 T + 96.1678 0.067571P +
kj
= 4.184

4
0.2225 + 1.6847 10 P T +
kmol.k
1.289 10 4 1.0095 10 7 P T 2

(
(

16

Reaction Heat
Elnashaie has developed a relation in 1981 for calculation of reaction heat which has been used in
our modeling [13].

846.609 459.734 10 6
P
5
.
34685
T

+
kj
0.54526 +

T
T3
H r = 4.184

kmol

3 2
6 3

0.2525 10 T + 1069197 10 T 9157.09

17

Pressure Drop[14,15,16]
To calculate the pressure drop inside beds, Ergun equation has been applied. This relation for a onedimensional flow is as below [15,16].

P = 2 u =

150(1 )

u
d p2

1.75

u 2
dp

18

As most of the industrial data along the beds are not available, the model is tested based on the
above values at the end of each bed. Applying mass, energy and momentum balance on an element,
derives the mathematical model. Considering all the points and discussions raised in the previous
sections, the below set of three differential equations are derived.

rNH 3
dz
=

dx 2 FN 2 A

dT
+ ( H r )rNH 3 = 0
uC p
dx

z
dP
150(1 ) u
1 u 2
2
1
.
75
= u =

dp
d p2
3
3
dx

19

Ali Dashti et al./Petroleum & Coal 48(2) 15-23 (2006)

20

The 4th order Runge Kutta approach is used to solve the above set of equations. As this set of
equations is stiff, pressure drop equation is first taken out of the set and the new set with two
equations is solved using Runge Kutta numerical method. At each stage of the numerical solution,
pressure drop is calculated by means of the temperature and concentration derived from that stage
and in this case the three parameters i.e. temperature, pressure and conversion rate are determined.
4. Modeling Results
Results taken from simulation are compared with industrial data. Input conditions are as below [17]:
Reactor input temperature: 266 C
Reactor input pressure: 136.5 bar
Desired temperature for input gas flow to the first bed: 371 C
Input flow rate to reactor: 183600 kg
hr

Input composition:
y0, N 2 = 0.2363680

y0,H 2 = 06567006
y0, NH 3 = 0.026930
y0,CH 4 = 0.059714
y0, Ar = 0.0202874
The above has been calculated after mixing with quench flow and the total flow of the reactor is
derived as 220200

kg
.
hr

Fig 2. Changes of N 2 conversion rate along the beds

Fig 2 illustrates the changes of N 2 conversion rate along the three beds. It is observed that changes
along the first bed are more sever than those of the second and third ones because of the lower
reaction product ( N 2 ) content in feed of this bed. The deflection in the curve between first and
second bed is because of change in the reaction speed, which is in turn resulted from gas cooling. As
no specific operation is carried out between second and third beds, the curve remains uniform along
them.

Ali Dashti et al./Petroleum & Coal 48(2) 15-23 (2006)

21

Fig 3. Molar fraction of the components along the beds

Molar fraction of the components along the bed can be deducted from the conversion rate and initial
mole fraction values. Fig 3 depicts the molar fraction of the three main components of the reaction.

Fig 4. Pressure Changes along the beds

Fig 4 illustrates pressure profile along the beds. In practice, pressure drop is more than that shown by
modeling as in the related simulation the catalyst particles are assumed to be spherical. Ferrite
catalyst doesnt have a regular shape which increases the pressure drop. The deflection in the curve
between first and second bed is resulted from the internal heat exchanger pressure drop.

Ali Dashti et al./Petroleum & Coal 48(2) 15-23 (2006)

22

Fig 5. Temperature Changes along the beds

Fig 5 illustrates the temperature changes along the beds. In first bed, as the ammonia concentration
is low, the reaction rate is very high and the temperature increases along the bed while approaching
equilibrium at its end (the slope of the curve is reduced along the bed). After first bed, gas is cooled
down in internal heat exchanger causing that to get far from equilibrium. As it is observed in the
figure, the gas approaches equilibrium at the end of third bed and the temperature change is low.
As previously mentioned, one of the capabilities of the developed software is investigation of changes
in the unit outputs. Analysis of these results, can lead us to find bottlenecks and high production
ways, etc. Fig. 6 and 7 illustrate some of the results.

Fig 6. Effect of changes in flow rate on different parameters

Ali Dashti et al./Petroleum & Coal 48(2) 15-23 (2006)

23

Fig 7. Effect of changes in input NH 3 concentration on different parameters

5. References
[1]
[2
[3]
[4]
[5]
[6]
[7]
[8]
[9]
[10]
[11]
[12]
[13]

[14]
[15]
[16]
[17]

R.W. Missen, C.A. Mims, B.A. Saville, Introduction to Chemical Reaction Engineering &
Kinetics , Wiley, 1999.
J. Morud, The dynamics of Chemical Reactors Whit Heat Integration, Ph.D thesis, 1995.
S. S. Elnashaie, M. E. Abashar And A. S. Al. Ubaid, Simulation and Optimization of an
Industrial Ammonia Reactor, Ind. Eng, chem.. Res, Vol. 27,pp. 2015, 1988.
D.C. Dyson and J.M. Sicon. A Kinetic Expression With Diffusion Correction for Ammonia
Synthesis on Industrial Catalyst, Ind. Eng. Chem. Fundamental, Vol. 7, No. 4, pp. 605, 1986.
P.P. Singh and N. Saraf Simulation of Ammonia Synthesis Reactor, Ind. Eng. Chem.
Process Des. Dev, Vol. 18, No.3, pp. 304, 1979.
P. Stoltze and J. K. Norshov, An Inter perdation of the High-pressure Kinetics of Ammonia
Synthesis Based on a Microscopic Model J. Catal, Vol. 110, pp. 1, 1988.
L. D. Gaines, Optimal Temperatures for Ammonia Synthesis Converters, Ind. Eng. Chem,
process Des. Dev, Vol. 16, No. 3, pp. 381, 1977.
rd
A. Nielsen, An investigation on Promoted Iron Catalysts for the Synthesis of Ammonia, 3
Ed, Jul. Gjellerups, Copenhagen, 1968
L. J. Gillespie, J. A. Beattie, Phys. Rev., Vol. 36, pp. 734, 1930
L. D. Gaines, Ammonia Synthesis Loop Variables Investigated By Steady-State Simulation,
Chem. Engng Sci, Vol. 34, pp. 37, 1970.
B. Elverse, S. Hawkins, W. Russey, G. Schulz, Ullman's Encyclopedia of Industrial
Chemistry, 5th Ed, Vol. A2, 1993.
M. J. Shah, Control Simulation in Ammonia Production, Ind. Eng. Chem., Vol 59, No 1, 72,
1967.
A.T. Mahfouz, S.S. Elshishini, and S.S.E.H. Elnashaie, Steady-State Modelling And
Simulation of an Industrial Ammonia Synthesis Reactor I. Reactor Modeling , Modeling
Simulation & control, B, ASME press, Vol. 10, No. 3, pp. 1, 1987.
S.S.E. H. Elnashaie and S.S. Elshishini, Modeling, Simulation, and Optimization of Industrial
Fixed Bed Catalytic Reactors, G&B Science, 1993.
S. Ergun, Fluid Flow Through Packed Columns, Chem. Engng. Prog., Vol 48, No 2, pp. 89,
1952.
F. Zardi, D.Bonvin, Modelling, Simulation and *Validation for an Axial- Radial Ammonia
Synthesis , Chem. Engng Sci., Vol. 47, No. 9-11 , pp. 2523, 1992.
Feasibility Study on Technology Transfer and Localization of Ammonia Synthesis Process in
Iran, Project report, Research Institute of Petroleum Industries, 2001.