Bucket Selection Guide*

Additional equipment

210G / 210G LC

BUCKET SIZE m3 (cu. yd.)

2.7
(3.5)

Key: Standard Optional or special

2.3
(3.0)
1.9
(2.5)

Deere 2.42-m (7 ft. 11 in.) Arm

1.5
(2.0)
Deere 2.91-m (9 ft. 7 in.) Arm

1.0
(1.5)
0.8
(1.0)

1800

1900

3,400
2000

3,600
2100

Wet Sand, Gravel

Moist Sand

1700
Wet Clay, Granite

1600

3,200

3,000

Wet Sand

2,800

Wet Earth

1500

Limestone

1400

Dry Clay

Shale

1300

2,600

2,400

Dry Sand

2,200

Caliche

Coal

Topsoil

Wet Peat

lb./cu. yd. 1,200 1,400 1,600 1,800 2,000

kg/m3 700 800 900 1000 1100 1200

* Contact your John Deere dealer for optimum bucket and attachment selections. These recommendations are for general conditions and average use. Does not include
optional equipment such as thumbs or couplers. Larger buckets may be possible when using light materials, for flat and level operations, less compacted materials, and
volume loading applications such as mass-excavation applications in ideal conditions. Smaller buckets are recommended for adverse conditions such as off-level applications, rocks, and uneven surfaces. Bucket capacity indicated is SAE heaped.

210G /
210G LC

Engine
Auto-idle system
Automatic belt-tension device
Batteries (2 12 volt)
Coolant recovery tank
Dual-element dry-type air lter
Electronic engine control
Enclosed fan guard (conforms to SAE J1308)
Engine coolant to 37 deg. C (34 deg. F)
Fuel lter with water separator
Full-ow oil lter
Turbocharger with charge air cooler
Cool-on-demand hydraulic-driven fan
500-hour engine-oil-change interval
70% (35 deg.) off-level capability
Engine-oil-sampling valve
Programmable auto shutdown
Chrome exhaust stack
Severe-duty fuel lter
Hydraulic fan reverser
Engine coolant heater
Hydraulic System
Reduced-drift valve for boom down, arm in
Auxiliary hydraulic valve section
Spring-applied, hydraulically released
automatic swing brake
Auxiliary hydraulic-ow adjustments
through monitor
Auto power lift
5,000-hour hydraulic-oil-change interval
Hydraulic-oil-sampling valve
Auxiliary hydraulic lines
Auxiliary pilot and electric controls
Hydraulic lter restriction indicator kit
Load-lowering control device
Single-pedal propel control
Control pattern-change valve
Undercarriage
Planetary drive with axial piston motors
Propel motor shields
Spring-applied, hydraulically released
automatic propel brake
Track guides, front idler and center
2-speed propel with automatic shift
Upper carrier rollers (2)
Sealed and lubricated track chain
Triple semi-grouser shoes, 600 mm (24 in.)
Triple semi-grouser shoes, 700 mm (28 in.)
Triple semi-grouser shoes, 800 mm (32 in.)

210G /
210G LC Upperstructure
Right-hand, left-hand, and counterweight

mirrors
Vandal locks with ignition key: Cab door /

Service doors / Toolbox

Debris screen in side panel

Remote-mounted engine oil and fuel lters

Front Attachments
Centralized lubrication system

Dirt seals on all bucket pins

Less boom and arm

Oil-impregnated bushings

Reinforced resin thrust plates

Tungsten carbide thermal coating on arm

to-bucket joint
Arm, 2.42 m (7 ft. 11 in.)

Arm, 2.91 m (9 ft. 7 in.)

Attachment quick-couplers

Boom cylinder with plumbing to mainframe

for less boom and arm

Buckets: Ditching / Heavy duty / Heavy
duty high capacity / Side cutters and teeth
Material clamps

Super-long fronts

Operators Station
Meets ISO 12117-2 for ROPS

Adjustable independent-control positions

(levers-to-seat, seat-to-pedals)
AM/FM radio

Auto climate control/air conditioner/

heater/pressurizer
Built-in Operators Manual storage com
partment and manual
Cell-phone power outlet, 12 volt, 60 watt,

5 amp
Coat hook

Deluxe suspension cloth seat with 100-mm

(4 in.) adjustable armrests

Floor mat

Front windshield wiper with intermittent

speeds
Gauges (illuminated): Engine coolant / Fuel

Horn, electric

Hour meter, electric

Hydraulic shutoff lever, all controls

Hydraulic warm-up control

Interior light

Large cup holder

Machine Information Center (MIC)

See your John Deere dealer for further information.

210G /
210G LC Operators Station (continued)
Mode selectors (illuminated): Power modes

(3) / Travel modes (2 with automatic shift) /

Work mode (1)
Multifunction, color LCD monitor with:

Diagnostic capability / Multiple-language

capabilities / Maintenance tracking / Clock /
System monitoring with alarm features:
Auto-idle indicator, engine air cleaner
restriction indicator light, engine check,
engine coolant temperature indicator light
with audible alarm, engine oil pressure
indicator light with audible alarm, lowalternator-charge indicator light, low-fuel
indicator light, fault code alert indicator,
fuel-rate display, wiper-mode indicator,
work-lights-on indicator, and work-mode
indicator
Motion alarm with cancel switch (conforms

to SAE J994)
Power-boost switch on right console lever

Auxiliary hydraulic control switches in right

console lever
SAE 2-lever control pattern

Seat belt, 51 mm (2 in.), retractable

Tinted glass

Transparent tinted overhead hatch

Hot/cold beverage compartment

Air-suspension heated seat

24- to 12-volt D.C. radio convertors, 10 amp

Hydraulic oil lter restriction indicator light

Protection screens for cab front, rear,

and side
Seat belt, 76 mm (3 in.), non-retractable

Window vandal-protection covers

Electrical
100-amp alternator

Blade-type multi-fused circuits

Positive-terminal battery covers

JDLink wireless communication system

(available in specic countries; see your

dealer for details)
Rearview camera

Cab extension wiring harness

Lights
Work lights: Halogen / One mounted on

boom / One mounted on frame

2 lights mounted on cab / One mounted

on right side of boom

Net engine power is with standard equipment including air cleaner, exhaust system, alternator, and cooling fan, at test conditions specied per ISO 9249.
No derating is required up to 3050-m (10,000 ft.) altitude. Specications and design subject to change without notice. Wherever applicable, specications
are in accordance with SAE standards. Except where otherwise noted, these specications are based on units with 1065-mm (42 in.), 0.91-m3 (1.19 cu. yd.),
886-kg (1,951 lb.) general-purpose buckets; 2.91-m (9 ft. 7 in.) arms; 4250-kg (9,370 lb.) counterweights; 800-mm (32 in.) triple semi-grouser shoes; full fuel
tanks; and 79-kg (175 lb.) operators.
DKAX210G Litho in U.S.A. (13-01)

www.JohnDeere.com

210G/210G LC
21 metric ton

210G / 210G LC
Engine

Manufacturer and Model

Non-Road Emissions Standard
Net Rated Power (ISO 9249)
Cylinders
Displacement
Off-Level Capacity
Aspiration

12
13

210G / 210G LC
Base engine for use in the U.S., U.S.
Territories, and Canada
John Deere PowerTech PVX
EPA Interim Tier 4/EU Stage IIIB
119 kW (159 hp) at 1,900 rpm
6
6.8 L (415 cu. in.)
70% (35 deg.)
Turbocharged, air-to-air charge-air
cooler

Optional engine for use outside the

U.S., U.S. Territories, and Canada
John Deere PowerTech Plus
EPA Tier 3/EU Stage IIIA
119 kW (159 hp) at 1,900 rpm
6
6.8 L (415 cu. in.)
70% (35 deg.)
Turbocharged, air-to-air charge-air
cooler

Optional engine for use outside the

U.S., U.S. Territories, and Canada
John Deere PowerTech
EPA Tier 2/EU Stage II
119 kW (159 hp) at 1,900 rpm
6
6.8 L (415 cu. in.)
70% (35 deg.)
Turbocharged, air-to-air charge-air
cooler

Cooling
Cool-on-demand hydraulic-driven, suction-type fan with remote-mounted drive
Powertrain
2-speed propel with automatic shift
Maximum Travel Speed
Low
3.5 km/h (2.2 mph)
High
5.5 km/h (3.4 mph)
Drawbar Pull
20 693 kg (45,620 lb.)
Hydraulics
Open center, load sensing
Main Pumps
2 variable-displacement axial-piston pumps
Maximum Rated Flow
212 L/m (56 gpm) x 2
Pilot Pump
One gear
Maximum Rated Flow
30.0 L/m (7.9 gpm)
Pressure Setting
3999 kPa (580 psi)
System Operating Pressure
Circuits
Implement
34 336 kPa (4,980 psi)
Travel
34 336 kPa (4,980 psi)
Swing
34 336 kPa (4,980 psi)
Power Boost
38 000 kPa (5,511 psi)
Controls
Pilot levers, short stroke, low-effort hydraulic pilot controls with shutoff lever
Cylinders
Bore
Rod Diameter
Stroke
Boom (2)
120 mm (4.72 in.)
85 mm (3.35 in.)
1260 mm (49.61 in.)
Arm (1)
135 mm (5.31 in.)
95 mm (3.74 in.)
1475 mm (58.07 in.)
Bucket (1)
115 mm (4.53 in.)
80 mm (3.15 in.)
1060 mm (41.73 in.)
Electrical
Number of Batteries (12 volt)
2
Battery Capacity
1,400 CCA
Alternator Rating
100 amp
Work Lights
2 halogen (one mounted on boom, one on frame)
Undercarriage
210G
210G LC
Rollers (each side)
Carrier
2
2
Track
7
8
Shoes, Triple Semi-Grousers (each side) 46
49
Track
Adjustment
Hydraulic
Hydraulic
Guides
Center
Center
Chain
Sealed and lubricated
Sealed and lubricated
Ground Pressure
Triple Semi-Grouser Shoes
600 mm (24 in.)
45.0 kPa (6.53 psi)
47.9 kPa (6.95 psi)
700 mm (28 in.)
39.0 kPa (5.66 psi)
41.7 kPa (6.05 psi)
800 mm (32 in.)
34.0 kPa (4.93 psi)
36.9 kPa (5.35 psi)
Swing Mechanism
Speed
13.3 rpm
Torque
68 900 Nm (50,662 lb.-ft.)

CENTERLINE OF SWING

Serviceability
210G / 210G LC
Rell Capacities
Fuel Tank
403 L (106.5 gal.)
Cooling System
30.5 L (32.2 qt.)
Engine Oil with Filter
20.8 L (22 qt.)
Hydraulic Tank
135 L (35.7 gal.)
Hydraulic System
240 L (63.4 gal.)
Gearbox
Swing
6.2 L (6.6 qt.)
Propel (each)
7.8 L (8.2 qt.)
Pump Drive
1.0 L (1.1 qt.)
Operating Weights
210G
210G LC
With full fuel tank; 79-kg (175 lb.) operator; 1065-mm (42 in.), 0.91-m3 (1.19 cu. yd.), 886-kg (1,951 lb.) general-purpose bucket; 2.91-m (9 ft. 7 in.) arm; 4250-kg (9,370 lb.)
counterweight; and 800-mm (32 in.) triple semi-grouser shoes
Operating Weight
22 309 kg (49,139 lb.)
22 910 kg (50,463 lb.)
Component Weights
E
Undercarriage with Triple SemiGrouser Shoes
600 mm (24 in.)
6752 kg (14,873 lb.)
7353 kg (16,196 lb.)
700 mm (28 in.)
7143 kg (15,733 lb.)
7743 kg (17,055 lb.)
800 mm (32 in.)
7437 kg (16,381 lb.)
8038 kg (17,705 lb.)
C D
One-Piece Boom (with arm cylinder)
1732 kg (3,815 lb.)
1732 kg (3,815 lb.)
Arm with Bucket Cylinder and Linkage
2.22 m (7 ft. 3 in.)
928 kg (2,044 lb.)
928 kg (2,044 lb.)
2.91 m (9 ft. 7 in.)
990 kg (2,181 lb.)
990 kg (2,181 lb.)
Boom-Lift Cylinders (2), Total Weight 341 kg (751 lb.)
341 kg (751 lb.)
1065-mm (42 in.), 0.91-m3 (1.19 cu.
886 kg (1,952 lb.)
886 kg (1,952 lb.)
GROUND LINE
yd.), Heavy-Duty Bucket
A
G
Counterweight, Standard
4250 kg (9,370 lb.)
4250 kg (9,370 lb.)
B B

Operating Dimensions
Arm Length
Arm Digging Force
SAE
ISO
Bucket Digging Force
SAE
ISO
A Maximum Reach
A| Maximum Reach at Ground Level
B Maximum Digging Depth
B| Maximum Digging Depth at 2.44-m
(8 ft. 0 in.) Flat Bottom
C Maximum Cutting Height
D Maximum Dumping Height
E Minimum Swing Radius
F Maximum Vertical Wall
G Tail-Swing Radius

210G
2.42 m (7 ft. 11 in.)

2.91m (9 ft. 7 in.)

210G LC
2.42 m (7 ft. 11 in.)

2.91m (9 ft. 7 in.)

133 kN (29,959 lb.)

139 kN (31,355 lb.)

110 kN (24,773 lb.)

114 kN (25,543 lb.)

133 kN (29,959 lb.)

139 kN (31,355 lb.)

110 kN (24,773 lb.)

114 kN (25,543 lb.)

142 kN (31,865 lb.)

156 kN (35,138 lb.)
9.43 m (30 ft. 11 in.)
9.25 m (30 ft. 4 in.)
6.18 m (20 ft. 3 in.)
5.95 m (19 ft. 6 in.)

142 kN (31,865 lb.)

156 kN (35,138 lb.)
9.92 m (32 ft. 7 in.)
9.75 m (32 ft. 0 in.)
6.68 m (21 ft. 11 in.)
6.50 m (21 ft. 4 in.)

142 kN (31,865 lb.)

156 kN (35,138 lb.)
9.43 m (30 ft. 11 in.)
9.25 m (30 ft. 4 in.)
6.18 m (20 ft. 3 in.)
5.95 m (19 ft. 6 in.)

142 kN (31,865 lb.)

156 kN (35,138 lb.)
9.92 m (32 ft. 7 in.)
9.75 m (32 ft. 0 in.)
6.68 m (21 ft. 11 in.)
6.50 m (21 ft. 4 in.)

9.67 m (31 ft. 9 in.)

6.83 m (22 ft. 5 in.)
3.28 m (10 ft. 9 in.)
5.30 m (17 ft. 5 in.)
2.89 m (9 ft. 6 in.)

10.04 m (32 ft. 11 in.)

7.18 m (23 ft. 7 in.)
3.18 m (10 ft. 5 in.)
5.99 m (19 ft. 8 in)
2.89 m (9 ft. 6 in.)

9.67 m (31 ft. 9 in.)

6.83 m (22 ft. 5 in.)
3.28 m (10 ft. 9 in.)
5.30 m (17 ft. 5 in.)
2.89 m (9 ft. 6 in.)

10.04 m (32 ft. 11 in.)

7.18 m (23 ft. 7 in.)
3.18 m (10 ft. 5 in.)
5.99 m (19 ft. 8 in)
2.89 m (9 ft. 6 in.)

Machine Dimensions
A Overall Length with Arm
2.42 m (7 ft. 11 in.)
2.91 m (9 ft. 7 in.)
B Overall Height with Arm
2.42 m (7 ft. 11 in.)
2.91 m (9 ft. 7 in.)
C Rear-End Length/Swing Radius
D Distance Between Idler/Sprocket Centerline
E Undercarriage Length
F Counterweight Clearance
G Upperstructure Width
H Cab Height
I Track Width
J Gauge Width
K Ground Clearance
L Overall Width with Triple Semi-Grouser Shoes
600 mm (24 in.)
700 mm (28 in.)
800 mm (32 in.)

210G

210G LC

9.75 m (32 ft. 0 in.)

9.53 m (31 ft. 3 in.)

9.75 m (32 ft. 0 in.)

9.53 m (31 ft. 3 in.)

3.18 m (10 ft. 5 in.)

3.01 m (9 ft. 11 in.)
2.89 m (9 ft. 6 in.)
3.35 m (11 ft. 0 in.)
4.17 m (13 ft. 8 in.)
1030 mm (3 ft. 5 in.)
2.71 m (8 ft. 11 in.)
2.95 m (9 ft. 8 in.)
600 mm (24 in.) / 700 mm (28 in.) / 800 mm (32 in.)
2.22 m (7 ft. 3 in.)
450 mm (17.72 in.)

3.18 m (10 ft. 5 in.)

3.01 m (9 ft. 11 in.)
2.89 m (9 ft. 6 in.)
3.67 m (12 ft. 0 in.)
4.46 m (14 ft. 8 in.)
1030 mm (3 ft. 5 in.)
2.71 m (8 ft. 11 in.)
2.95 m (9 ft. 8 in.)
600 mm (24 in.) / 700 mm (28 in.) / 800 mm (32 in.)
2.39 m (7 ft. 10 in.)
450 mm (17.72 in.)

2.82 m (9 ft. 3 in.)

2.92 m (9 ft. 7 in.)
3.02 m (9 ft. 11 in.)

2.99 m (9 ft. 10 in.)

3.09 m (10 ft. 2 in.)
3.19 m (10 ft. 6 in.)

F
B

D
E

I
J
L

210G Lift Capacities

Boldface type indicates hydraulically limited capacity; lightface type indicates stability-limited capacities, in kg (lb.). Ratings at bucket lift hook; machine equipped with 666-kg (1,468 lb.)
bucket, standard counterweight, and standard gauge; and situated on rm, level, uniform supporting surface. Total load includes weight of cables, hook, etc. Figures do not exceed 87 percent
of hydraulic capacities or 75 percent of weight needed to tip machine. All lift capacities are based on ISO 10567 (with power boost).
Load Point Height
1.5 m (5 ft.)
3.0 m (10 ft.)
4.5 m (15 ft.)
6.0 m (20 ft.)
7.5 m (25 ft.)
Horizontal Distance from
Centerline of Rotation
Over Front
Over Side
Over Front
Over Side
Over Front
Over Side
Over Front
Over Side
Over Front
Over Side
With 2.91-m (9 ft. 7 in.) arm and 700-mm (28 in.) triple semi-grouser shoes
6.0 m (20 ft.)
4700
4450
(10,300)
(9,500)
4.5 m (15 ft.)
6150
6150
5250
4300
4500
2850
(13,250)
(13,250)
(11,450)
(9,250)
(9,600)
(6,150)
3.0 m (10 ft.)
8050
6400
6150
4050
4400
2800
(17,350)
(13,800)
(13,350)
(8,750)
(9,450)
(5,950)
1.5 m (5 ft.)
9800
5950
6150
3850
4300
2700
(21,100)
(12,800)
(13,200)
(8,250)
(9,200)
(5,750)
Ground Line
4150
4150
9500
5650
5950
3700
4200
2600
(9,650)
(9,650)
(20,400)
(12,200)
(12,800)
(7,900)
(9,000)
(5,600)
1.5 m (5 ft.)
4800
4800
8400
8400
9400
5600
5850
3600
4150
2550
(10,750)
(10,750)
(19,100)
(19,100)
(20,200)
(12,050)
(12,650)
(7,750)
(8,950)
(5,550)
3.0 m (10 ft.)
9250
9250
13 950
11 150
9500
5650
5900
3650
(20,850)
(20,850)
(30,250)
(23,950)
(20,350)
(12,150)
(12,750)
(7,850)
4.5 m (15 ft.)
10 850
10 850
7650
5850
(23,150)
(23,150)
(16,250)
(12,650)

14
15

Bucket Selection Guide*

Additional equipment

210G / 210G LC

BUCKET SIZE m3 (cu. yd.)

2.7
(3.5)

Key: Standard Optional or special

2.3
(3.0)
1.9
(2.5)

Deere 2.42-m (7 ft. 11 in.) Arm

1.5
(2.0)
Deere 2.91-m (9 ft. 7 in.) Arm

1.0
(1.5)
0.8
(1.0)

1800

1900

3,400
2000

3,600
2100

Wet Sand, Gravel

Moist Sand

1700
Wet Clay, Granite

1600

3,200

3,000

Wet Sand

2,800

Wet Earth

1500

Limestone

1400

Dry Clay

Shale

1300

2,600

2,400

Dry Sand

2,200

Caliche

Coal

Topsoil

Wet Peat

lb./cu. yd. 1,200 1,400 1,600 1,800 2,000

kg/m3 700 800 900 1000 1100 1200

* Contact your John Deere dealer for optimum bucket and attachment selections. These recommendations are for general conditions and average use. Does not include
optional equipment such as thumbs or couplers. Larger buckets may be possible when using light materials, for flat and level operations, less compacted materials, and
volume loading applications such as mass-excavation applications in ideal conditions. Smaller buckets are recommended for adverse conditions such as off-level applications, rocks, and uneven surfaces. Bucket capacity indicated is SAE heaped.

210G /
210G LC

Engine
Auto-idle system
Automatic belt-tension device
Batteries (2 12 volt)
Coolant recovery tank
Dual-element dry-type air lter
Electronic engine control
Enclosed fan guard (conforms to SAE J1308)
Engine coolant to 37 deg. C (34 deg. F)
Fuel lter with water separator
Full-ow oil lter
Turbocharger with charge air cooler
Cool-on-demand hydraulic-driven fan
500-hour engine-oil-change interval
70% (35 deg.) off-level capability
Engine-oil-sampling valve
Programmable auto shutdown
Chrome exhaust stack
Severe-duty fuel lter
Hydraulic fan reverser
Engine coolant heater
Hydraulic System
Reduced-drift valve for boom down, arm in
Auxiliary hydraulic valve section
Spring-applied, hydraulically released
automatic swing brake
Auxiliary hydraulic-ow adjustments
through monitor
Auto power lift
5,000-hour hydraulic-oil-change interval
Hydraulic-oil-sampling valve
Auxiliary hydraulic lines
Auxiliary pilot and electric controls
Hydraulic lter restriction indicator kit
Load-lowering control device
Single-pedal propel control
Control pattern-change valve
Undercarriage
Planetary drive with axial piston motors
Propel motor shields
Spring-applied, hydraulically released
automatic propel brake
Track guides, front idler and center
2-speed propel with automatic shift
Upper carrier rollers (2)
Sealed and lubricated track chain
Triple semi-grouser shoes, 600 mm (24 in.)
Triple semi-grouser shoes, 700 mm (28 in.)
Triple semi-grouser shoes, 800 mm (32 in.)

210G /
210G LC Upperstructure
Right-hand, left-hand, and counterweight

mirrors
Vandal locks with ignition key: Cab door /

Service doors / Toolbox

Debris screen in side panel

Remote-mounted engine oil and fuel lters

Front Attachments
Centralized lubrication system

Dirt seals on all bucket pins

Less boom and arm

Oil-impregnated bushings

Reinforced resin thrust plates

Tungsten carbide thermal coating on arm

to-bucket joint
Arm, 2.42 m (7 ft. 11 in.)

Arm, 2.91 m (9 ft. 7 in.)

Attachment quick-couplers

Boom cylinder with plumbing to mainframe

for less boom and arm

Buckets: Ditching / Heavy duty / Heavy
duty high capacity / Side cutters and teeth
Material clamps

Super-long fronts

Operators Station
Meets ISO 12117-2 for ROPS

Adjustable independent-control positions

(levers-to-seat, seat-to-pedals)
AM/FM radio

Auto climate control/air conditioner/

heater/pressurizer
Built-in Operators Manual storage com
partment and manual
Cell-phone power outlet, 12 volt, 60 watt,

5 amp
Coat hook

Deluxe suspension cloth seat with 100-mm

(4 in.) adjustable armrests

Floor mat

Front windshield wiper with intermittent

speeds
Gauges (illuminated): Engine coolant / Fuel

Horn, electric

Hour meter, electric

Hydraulic shutoff lever, all controls

Hydraulic warm-up control

Interior light

Large cup holder

Machine Information Center (MIC)

See your John Deere dealer for further information.

210G /
210G LC Operators Station (continued)
Mode selectors (illuminated): Power modes

(3) / Travel modes (2 with automatic shift) /

Work mode (1)
Multifunction, color LCD monitor with:

Diagnostic capability / Multiple-language

capabilities / Maintenance tracking / Clock /
System monitoring with alarm features:
Auto-idle indicator, engine air cleaner
restriction indicator light, engine check,
engine coolant temperature indicator light
with audible alarm, engine oil pressure
indicator light with audible alarm, lowalternator-charge indicator light, low-fuel
indicator light, fault code alert indicator,
fuel-rate display, wiper-mode indicator,
work-lights-on indicator, and work-mode
indicator
Motion alarm with cancel switch (conforms

to SAE J994)
Power-boost switch on right console lever

Auxiliary hydraulic control switches in right

console lever
SAE 2-lever control pattern

Seat belt, 51 mm (2 in.), retractable

Tinted glass

Transparent tinted overhead hatch

Hot/cold beverage compartment

Air-suspension heated seat

24- to 12-volt D.C. radio convertors, 10 amp

Hydraulic oil lter restriction indicator light

Protection screens for cab front, rear,

and side
Seat belt, 76 mm (3 in.), non-retractable

Window vandal-protection covers

Electrical
100-amp alternator

Blade-type multi-fused circuits

Positive-terminal battery covers

JDLink wireless communication system

(available in specic countries; see your

dealer for details)
Rearview camera

Cab extension wiring harness

Lights
Work lights: Halogen / One mounted on

boom / One mounted on frame

2 lights mounted on cab / One mounted

on right side of boom

Net engine power is with standard equipment including air cleaner, exhaust system, alternator, and cooling fan, at test conditions specied per ISO 9249.
No derating is required up to 3050-m (10,000 ft.) altitude. Specications and design subject to change without notice. Wherever applicable, specications
are in accordance with SAE standards. Except where otherwise noted, these specications are based on units with 1065-mm (42 in.), 0.91-m3 (1.19 cu. yd.),
886-kg (1,951 lb.) general-purpose buckets; 2.91-m (9 ft. 7 in.) arms; 4250-kg (9,370 lb.) counterweights; 800-mm (32 in.) triple semi-grouser shoes; full fuel
tanks; and 79-kg (175 lb.) operators.
DKAX210G Litho in U.S.A. (13-01)

www.JohnDeere.com

210G/210G LC
21 metric ton

210G Lift Capacities (continued)

210G LC Lift Capacities (continued)

Boldface type indicates hydraulically limited capacity; lightface type indicates stability-limited capacities, in kg (lb.). Ratings at bucket lift hook; machine equipped with 666-kg (1,468 lb.)
bucket, standard counterweight, and standard gauge; and situated on rm, level, uniform supporting surface. Total load includes weight of cables, hook, etc. Figures do not exceed 87 percent
of hydraulic capacities or 75 percent of weight needed to tip machine. All lift capacities are based on ISO 10567 (with power boost).
Load Point Height
1.5 m (5 ft.)
3.0 m (10 ft.)
4.5 m (15 ft.)
6.0 m (20 ft.)
7.5 m (25 ft.)
Horizontal Distance from
Centerline of Rotation
Over Front
Over Side
Over Front
Over Side
Over Front
Over Side
Over Front
Over Side
Over Front
Over Side
With 2.91-m (9 ft. 7 in.) arm and 800-mm (32 in.) triple semi-grouser shoes
6.0 m (20 ft.)
4700
4500
(10,300)
(9,650)
4.5 m (15 ft.)
6150
6150
5250
4350
4600
2950
(13,250)
(13,250)
(11,450)
(9,400)
(9,800)
(6,250)
3.0 m (10 ft.)
8050
6500
6150
4150
4500
2850
(17,350)
(14,050)
(13,350)
(8,950)
(9,650)
(6,100)
1.5 m (5 ft.)
9800
6050
6250
3900
4350
2750
(21,100)
(13,000)
(13,450)
(8,450)
(9,400)
(5,850)
Ground Line
4150
4150
9700
5750
6050
3750
4300
2650
(9,650)
(9,650)
(20,800)
(12,450)
(13,050)
(8,050)
(9,200)
(5,700)
1.5 m (5 ft.)
4800
4800
8400
8400
9600
5700
6000
3700
4250
2650
(10,750)
(10,750)
(19,100)
(19,100)
(20,600)
(12,250)
(12,900)
(7,900)
(9,150)
(5,650)
3.0 m (10 ft.)
9250
9250
13 950
11 350
9650
5750
6050
3700
(20,850)
(20,850)
(30,250)
(24,350)
(20,750)
(12,400)
(13,000)
(8,000)
4.5 m (15 ft.)
10 850
10 850
7650
5950
(23,150)
(23,150)
(16,250)
(12,850)

Boldface type indicates hydraulically limited capacity; lightface type indicates stability-limited capacities, in kg (lb.). Ratings at bucket lift hook; machine equipped with 666-kg (1,468 lb.)
bucket, standard counterweight, and standard gauge; and situated on rm, level, uniform supporting surface. Total load includes weight of cables, hook, etc. Figures do not exceed 87 percent
of hydraulic capacities or 75 percent of weight needed to tip machine. All lift capacities are based on ISO 10567 (with power boost).
Load Point Height
1.5 m (5 ft.)
3.0 m (10 ft.)
4.5 m (15 ft.)
6.0 m (20 ft.)
7.5 m (25 ft.)
Horizontal Distance from
Centerline of Rotation
Over Front
Over Side
Over Front
Over Side
Over Front
Over Side
Over Front
Over Side
Over Front
Over Side
With 2.91-m (9 ft. 7 in.) arm and 700-mm (28 in.) triple semi-grouser shoes
6.0 m (20 ft.)
4700
4700
(10,300)
(10,300)
4.5 m (15 ft.)
6150
6150
5250
4800
4850
3250
(13,250)
(13,250)
(11,450)
(10,350)
(10,650)
(6,950)
3.0 m (10 ft.)
8050
7250
6150
4600
5050
3150
(17,350)
(15,600)
(13,350)
(9,850)
(10,850)
(6,750)
1.5 m (5 ft.)
9800
6750
7050
4350
4950
3050
(21,100)
(14,500)
(15,200)
(9,350)
(10,600)
(6,550)
Ground Line
4150
4150
10 650
6450
6900
4200
4850
2950
(9,650)
(9,650)
(23,050)
(13,900)
(14,850)
(9,000)
(10,400)
(6,350)
1.5 m (5 ft.)
4800
4800
8400
8400
10 600
6400
6800
4100
4800
2950
(10,750)
(10,750)
(19,100)
(19,100)
(23,000)
(13,750)
(14,650)
(8,850)
(10,350)
(6,350)
3.0 m (10 ft.)
9250
9250
13 950
12 950
9750
6450
6850
4150
(20,850)
(20,850)
(30,250)
(27,750)
(21,050)
(13,900)
(14,750)
(8,950)
4.5 m (15 ft.)
10 850
10 850
7650
6650
(23,150)
(23,150)
(16,250)
(14,350)
With 2.91-m (9 ft. 7 in.) arm and 800-mm (32 in.) triple semi-grouser shoes
6.0 m (20 ft.)
4700
4700
(10,300)
(10,300)
4.5 m (15 ft.)
6150
6150
5250
4900
4850
3300
(13,250)
(13,250)
(11,450)
(10,500)
(10,650)
(7,050)
3.0 m (10 ft.)
8050
7350
6150
4650
5150
3200
(17,350)
(15,850)
(13,350)
(10,050)
(11,050)
(6,900)
1.5 m (5 ft.)
9800
6850
7050
4450
5050
3100
(21,100)
(14,750)
(15,200)
(9,550)
(10,800)
(6,700)
Ground Line
4150
4150
10 650
6600
7050
4250
4950
3000
(9,650)
(9,650)
(23,050)
(14,150)
(15,100)
(9,150)
(10,650)
(6,500)
1.5 m (5 ft.)
4800
4800
8400
8400
10 600
6500
6950
4200
4900
3000
(10,750)
(10,750)
(19,100)
(19,100)
(23,000)
(14,000)
(14,950)
(9,000)
(10,600)
(6,450)
3.0 m (10 ft.)
9250
9250
13 950
13 200
9750
6550
7000
4200
(20,850)
(20,850)
(30,250)
(28,200)
(21,050)
(14,150)
(15,050)
(9,100)
4.5 m (15 ft.)
10 850
10 850
7650
6800
(23,150)
(23,150)
(16,250)
(14,600)

210G LC Lift Capacities

Boldface type indicates hydraulically limited capacity; lightface type indicates stability-limited capacities, in kg (lb.). Ratings at bucket lift hook; machine equipped with 666-kg (1,468 lb.)
bucket, standard counterweight, and standard gauge; and situated on rm, level, uniform supporting surface. Total load includes weight of cables, hook, etc. Figures do not exceed 87 percent
of hydraulic capacities or 75 percent of weight needed to tip machine. All lift capacities are based on ISO 10567 (with power boost).
Load Point Height
1.5 m (5 ft.)
3.0 m (10 ft.)
4.5 m (15 ft.)
6.0 m (20 ft.)
7.5 m (25 ft.)
Horizontal Distance from
Centerline of Rotation
Over Front
Over Side
Over Front
Over Side
Over Front
Over Side
Over Front
Over Side
Over Front
Over Side
With 2.42-m (7 ft. 11 in.) arm and 800-mm (32 in.) triple semi-grouser shoes
6.0 m (20 ft.)
5200
4950
(11,450)
(10,600)
4.5 m (15 ft.)
6850
6850
5750
4850
(20,650)
(20,650)
(14,800)
(14,800)
(12,450)
(10,400)
3.0 m (10 ft.)
8750
7200
6550
4600
5150
3200
(18,800)
(15,550)
(14,150)
(9,950)
(11,000)
(6,850)
1.5 m (5 ft.)
10 250
6750
7200
4400
5050
3100
(22,100)
(14,550)
(15,450)
(9,500)
(10,800)
(6,700)
Ground Line
10 750
6550
7050
4250
4950
3050
(23,300)
(14,150)
(15,100)
(9,200)
(10,650)
(6,550)
1.5 m (5 ft.)
9150
9150
10 450
6550
7000
4250
(21,050)
(21,050)
(22,600)
(14,100)
(15,050)
(9,100)
3.0 m (10 ft.)
12 800
12 800
9250
6650
6650
4300
(27,750)
(27,750)
(20,000)
(14,300)
(14,200)
(9,300)
4.5 m (15 ft.)
6400
6400
(13,250)
(13,250)
With 2.91-m (9 ft. 7 in.) arm and 600-mm (24 in.) triple semi-grouser shoes
6.0 m (20 ft.)
4700
4700
(10,300)
(10,300)
4.5 m (15 ft.)
6150
6150
5250
4700
4850
3150
(13,250)
(13,250)
(11,450)
(10,150)
(10,650)
(6,750)
3.0 m (10 ft.)
8050
7100
6150
4500
4950
3100
(17,350)
(15,250)
(13,350)
(9,650)
(10,600)
(6,600)
1.5 m (5 ft.)
9800
6600
6900
4250
4800
2950
(21,100)
(14,200)
(14,900)
(9,150)
(10,350)
(6,400)
Ground Line
4150
4150
10 650
6300
6750
4100
4700
2900
(9,650)
(9,650)
(23,050)
(13,600)
(14,500)
(8,800)
(10,150)
(6,200)
1.5 m (5 ft.)
4800
4800
8400
8400
10 600
6250
6650
4000
4700
2850
(10,750)
(10,750)
(19,100)
(19,100)
(23,000)
(13,400)
(14,300)
(8,600)
(10,100)
(6,150)
3.0 m (10 ft.)
9250
9250
13 950
12 700
9750
6300
6700
4050
(20,850)
(20,850)
(30,250)
(27,150)
(21,050)
(13,550)
(14,400)
(8,700)
4.5 m (15 ft.)
10 850
10 850
7650
6500
(23,150)
(23,150)
(16,250)
(14,050)

Cover all the angles.

2
3

Heavier and stronger than their popular predecessors, the 210G and 210G LC are also more
productive. So, whether you use them to excavate footings, load trucks, set stone, place pipe,
or whatever, youll get more done per gallon of fuel. Their rugged EPA Interim Tier 4 (IT4)/
EU Stage IIIB PowerTech diesel engines meet rigid emission regulations, enabling you to work,
wherever you work, even in nonattainment areas. Whats more, theyre loaded with customerinspired renements such as more comfortable and spacious cabs. Enhanced LCD monitors
with simplied navigation that lets an operator easily dial-in a wealth of machine info and
functionality. Exceptional power, smoothness, operating ease, and IT4 compliance the highly
versatile 210G and 210G LC cover all the angles so you can, too.

16
17

Buckets

210G / 210G LC

A full line of buckets is offered to meet a wide variety of applications. Digging forces are with power boost. Buckets are equipped with John Deere Fanggs or ESCO teeth standard.
Replaceable cutting edges and a variety of teeth are available through John Deere Parts. Optional side cutters add 150 mm (6 in.) to bucket widths. Capacities are SAE heaped ratings.
Arm Dig Force
Arm Dig Force
Number
Type Bucket
Bucket Width
Bucket Capacity
Bucket Weight
Bucket Dig Force
2.42 m (7 ft. 11 in.)
2.91 m (9 ft. 7 in.)
Bucket Tip Radius of Teeth
cu. yd.
kg
lb.
kN
lb.
kN
lb.
kN
lb.
mm
in.
mm
in.
m3
Heavy Duty
915
36
0.69
0.90
708
1,559
135.9
30,554
130.2
29,271
107.1
24,071
1463
57.61
5
1065
42
0.83
1.09
786
1,731
135.9
30,554
130.2
29,271
107.1
24,071
1463
57.61
5
1220
48
0.99
1.29
872
1,921
135.9
30,554
130.2
29,271
107.1
24,071
1463
57.61
6
Heavy Duty
High Capacity
610
24
0.43
0.56
646
1,424
135.0
30,349
129.9
29,197
106.8
24,016
1473
58.00
4
760
30
0.58
0.76
723
1,593
135.0
30,349
129.9
29,197
106.8
24,016
1473
58.00
4
915
36
0.74
0.97
809
1,782
135.0
30,349
129.9
29,197
106.8
24,016
1473
58.00
5
1065
42
0.91
1.19
886
1,951
135.0
30,349
129.9
29,197
106.8
24,016
1473
58.00
5

210G Lift Capacities (continued)

210G LC Lift Capacities (continued)

Boldface type indicates hydraulically limited capacity; lightface type indicates stability-limited capacities, in kg (lb.). Ratings at bucket lift hook; machine equipped with 666-kg (1,468 lb.)
bucket, standard counterweight, and standard gauge; and situated on rm, level, uniform supporting surface. Total load includes weight of cables, hook, etc. Figures do not exceed 87 percent
of hydraulic capacities or 75 percent of weight needed to tip machine. All lift capacities are based on ISO 10567 (with power boost).
Load Point Height
1.5 m (5 ft.)
3.0 m (10 ft.)
4.5 m (15 ft.)
6.0 m (20 ft.)
7.5 m (25 ft.)
Horizontal Distance from
Centerline of Rotation
Over Front
Over Side
Over Front
Over Side
Over Front
Over Side
Over Front
Over Side
Over Front
Over Side
With 2.91-m (9 ft. 7 in.) arm and 800-mm (32 in.) triple semi-grouser shoes
6.0 m (20 ft.)
4700
4500
(10,300)
(9,650)
4.5 m (15 ft.)
6150
6150
5250
4350
4600
2950
(13,250)
(13,250)
(11,450)
(9,400)
(9,800)
(6,250)
3.0 m (10 ft.)
8050
6500
6150
4150
4500
2850
(17,350)
(14,050)
(13,350)
(8,950)
(9,650)
(6,100)
1.5 m (5 ft.)
9800
6050
6250
3900
4350
2750
(21,100)
(13,000)
(13,450)
(8,450)
(9,400)
(5,850)
Ground Line
4150
4150
9700
5750
6050
3750
4300
2650
(9,650)
(9,650)
(20,800)
(12,450)
(13,050)
(8,050)
(9,200)
(5,700)
1.5 m (5 ft.)
4800
4800
8400
8400
9600
5700
6000
3700
4250
2650
(10,750)
(10,750)
(19,100)
(19,100)
(20,600)
(12,250)
(12,900)
(7,900)
(9,150)
(5,650)
3.0 m (10 ft.)
9250
9250
13 950
11 350
9650
5750
6050
3700
(20,850)
(20,850)
(30,250)
(24,350)
(20,750)
(12,400)
(13,000)
(8,000)
4.5 m (15 ft.)
10 850
10 850
7650
5950
(23,150)
(23,150)
(16,250)
(12,850)

Boldface type indicates hydraulically limited capacity; lightface type indicates stability-limited capacities, in kg (lb.). Ratings at bucket lift hook; machine equipped with 666-kg (1,468 lb.)
bucket, standard counterweight, and standard gauge; and situated on rm, level, uniform supporting surface. Total load includes weight of cables, hook, etc. Figures do not exceed 87 percent
of hydraulic capacities or 75 percent of weight needed to tip machine. All lift capacities are based on ISO 10567 (with power boost).
Load Point Height
1.5 m (5 ft.)
3.0 m (10 ft.)
4.5 m (15 ft.)
6.0 m (20 ft.)
7.5 m (25 ft.)
Horizontal Distance from
Centerline of Rotation
Over Front
Over Side
Over Front
Over Side
Over Front
Over Side
Over Front
Over Side
Over Front
Over Side
With 2.91-m (9 ft. 7 in.) arm and 700-mm (28 in.) triple semi-grouser shoes
6.0 m (20 ft.)
4700
4700
(10,300)
(10,300)
4.5 m (15 ft.)
6150
6150
5250
4800
4850
3250
(13,250)
(13,250)
(11,450)
(10,350)
(10,650)
(6,950)
3.0 m (10 ft.)
8050
7250
6150
4600
5050
3150
(17,350)
(15,600)
(13,350)
(9,850)
(10,850)
(6,750)
1.5 m (5 ft.)
9800
6750
7050
4350
4950
3050
(21,100)
(14,500)
(15,200)
(9,350)
(10,600)
(6,550)
Ground Line
4150
4150
10 650
6450
6900
4200
4850
2950
(9,650)
(9,650)
(23,050)
(13,900)
(14,850)
(9,000)
(10,400)
(6,350)
1.5 m (5 ft.)
4800
4800
8400
8400
10 600
6400
6800
4100
4800
2950
(10,750)
(10,750)
(19,100)
(19,100)
(23,000)
(13,750)
(14,650)
(8,850)
(10,350)
(6,350)
3.0 m (10 ft.)
9250
9250
13 950
12 950
9750
6450
6850
4150
(20,850)
(20,850)
(30,250)
(27,750)
(21,050)
(13,900)
(14,750)
(8,950)
4.5 m (15 ft.)
10 850
10 850
7650
6650
(23,150)
(23,150)
(16,250)
(14,350)
With 2.91-m (9 ft. 7 in.) arm and 800-mm (32 in.) triple semi-grouser shoes
6.0 m (20 ft.)
4700
4700
(10,300)
(10,300)
4.5 m (15 ft.)
6150
6150
5250
4900
4850
3300
(13,250)
(13,250)
(11,450)
(10,500)
(10,650)
(7,050)
3.0 m (10 ft.)
8050
7350
6150
4650
5150
3200
(17,350)
(15,850)
(13,350)
(10,050)
(11,050)
(6,900)
1.5 m (5 ft.)
9800
6850
7050
4450
5050
3100
(21,100)
(14,750)
(15,200)
(9,550)
(10,800)
(6,700)
Ground Line
4150
4150
10 650
6600
7050
4250
4950
3000
(9,650)
(9,650)
(23,050)
(14,150)
(15,100)
(9,150)
(10,650)
(6,500)
1.5 m (5 ft.)
4800
4800
8400
8400
10 600
6500
6950
4200
4900
3000
(10,750)
(10,750)
(19,100)
(19,100)
(23,000)
(14,000)
(14,950)
(9,000)
(10,600)
(6,450)
3.0 m (10 ft.)
9250
9250
13 950
13 200
9750
6550
7000
4200
(20,850)
(20,850)
(30,250)
(28,200)
(21,050)
(14,150)
(15,050)
(9,100)
4.5 m (15 ft.)
10 850
10 850
7650
6800
(23,150)
(23,150)
(16,250)
(14,600)

210G LC Lift Capacities

Boldface type indicates hydraulically limited capacity; lightface type indicates stability-limited capacities, in kg (lb.). Ratings at bucket lift hook; machine equipped with 666-kg (1,468 lb.)
bucket, standard counterweight, and standard gauge; and situated on rm, level, uniform supporting surface. Total load includes weight of cables, hook, etc. Figures do not exceed 87 percent
of hydraulic capacities or 75 percent of weight needed to tip machine. All lift capacities are based on ISO 10567 (with power boost).
Load Point Height
1.5 m (5 ft.)
3.0 m (10 ft.)
4.5 m (15 ft.)
6.0 m (20 ft.)
7.5 m (25 ft.)
Horizontal Distance from
Centerline of Rotation
Over Front
Over Side
Over Front
Over Side
Over Front
Over Side
Over Front
Over Side
Over Front
Over Side
With 2.42-m (7 ft. 11 in.) arm and 800-mm (32 in.) triple semi-grouser shoes
6.0 m (20 ft.)
5200
4950
(11,450)
(10,600)
4.5 m (15 ft.)
6850
6850
5750
4850
(20,650)
(20,650)
(14,800)
(14,800)
(12,450)
(10,400)
3.0 m (10 ft.)
8750
7200
6550
4600
5150
3200
(18,800)
(15,550)
(14,150)
(9,950)
(11,000)
(6,850)
1.5 m (5 ft.)
10 250
6750
7200
4400
5050
3100
(22,100)
(14,550)
(15,450)
(9,500)
(10,800)
(6,700)
Ground Line
10 750
6550
7050
4250
4950
3050
(23,300)
(14,150)
(15,100)
(9,200)
(10,650)
(6,550)
1.5 m (5 ft.)
9150
9150
10 450
6550
7000
4250
(21,050)
(21,050)
(22,600)
(14,100)
(15,050)
(9,100)
3.0 m (10 ft.)
12 800
12 800
9250
6650
6650
4300
(27,750)
(27,750)
(20,000)
(14,300)
(14,200)
(9,300)
4.5 m (15 ft.)
6400
6400
(13,250)
(13,250)
With 2.91-m (9 ft. 7 in.) arm and 600-mm (24 in.) triple semi-grouser shoes
6.0 m (20 ft.)
4700
4700
(10,300)
(10,300)
4.5 m (15 ft.)
6150
6150
5250
4700
4850
3150
(13,250)
(13,250)
(11,450)
(10,150)
(10,650)
(6,750)
3.0 m (10 ft.)
8050
7100
6150
4500
4950
3100
(17,350)
(15,250)
(13,350)
(9,650)
(10,600)
(6,600)
1.5 m (5 ft.)
9800
6600
6900
4250
4800
2950
(21,100)
(14,200)
(14,900)
(9,150)
(10,350)
(6,400)
Ground Line
4150
4150
10 650
6300
6750
4100
4700
2900
(9,650)
(9,650)
(23,050)
(13,600)
(14,500)
(8,800)
(10,150)
(6,200)
1.5 m (5 ft.)
4800
4800
8400
8400
10 600
6250
6650
4000
4700
2850
(10,750)
(10,750)
(19,100)
(19,100)
(23,000)
(13,400)
(14,300)
(8,600)
(10,100)
(6,150)
3.0 m (10 ft.)
9250
9250
13 950
12 700
9750
6300
6700
4050
(20,850)
(20,850)
(30,250)
(27,150)
(21,050)
(13,550)
(14,400)
(8,700)
4.5 m (15 ft.)
10 850
10 850
7650
6500
(23,150)
(23,150)
(16,250)
(14,050)

Cover all the angles.

2
3

Heavier and stronger than their popular predecessors, the 210G and 210G LC are also more
productive. So, whether you use them to excavate footings, load trucks, set stone, place pipe,
or whatever, youll get more done per gallon of fuel. Their rugged EPA Interim Tier 4 (IT4)/
EU Stage IIIB PowerTech diesel engines meet rigid emission regulations, enabling you to work,
wherever you work, even in nonattainment areas. Whats more, theyre loaded with customerinspired renements such as more comfortable and spacious cabs. Enhanced LCD monitors
with simplied navigation that lets an operator easily dial-in a wealth of machine info and
functionality. Exceptional power, smoothness, operating ease, and IT4 compliance the highly
versatile 210G and 210G LC cover all the angles so you can, too.

16
17

Buckets

210G / 210G LC

A full line of buckets is offered to meet a wide variety of applications. Digging forces are with power boost. Buckets are equipped with John Deere Fanggs or ESCO teeth standard.
Replaceable cutting edges and a variety of teeth are available through John Deere Parts. Optional side cutters add 150 mm (6 in.) to bucket widths. Capacities are SAE heaped ratings.
Arm Dig Force
Arm Dig Force
Number
Type Bucket
Bucket Width
Bucket Capacity
Bucket Weight
Bucket Dig Force
2.42 m (7 ft. 11 in.)
2.91 m (9 ft. 7 in.)
Bucket Tip Radius of Teeth
cu. yd.
kg
lb.
kN
lb.
kN
lb.
kN
lb.
mm
in.
mm
in.
m3
Heavy Duty
915
36
0.69
0.90
708
1,559
135.9
30,554
130.2
29,271
107.1
24,071
1463
57.61
5
1065
42
0.83
1.09
786
1,731
135.9
30,554
130.2
29,271
107.1
24,071
1463
57.61
5
1220
48
0.99
1.29
872
1,921
135.9
30,554
130.2
29,271
107.1
24,071
1463
57.61
6
Heavy Duty
High Capacity
610
24
0.43
0.56
646
1,424
135.0
30,349
129.9
29,197
106.8
24,016
1473
58.00
4
760
30
0.58
0.76
723
1,593
135.0
30,349
129.9
29,197
106.8
24,016
1473
58.00
4
915
36
0.74
0.97
809
1,782
135.0
30,349
129.9
29,197
106.8
24,016
1473
58.00
5
1065
42
0.91
1.19
886
1,951
135.0
30,349
129.9
29,197
106.8
24,016
1473
58.00
5