INTERNATIONAL Iso STANDARD 1234 Second edition 1997-11-01 ee Split pins Goupilles fendues Reference number ISO 1234:1997(6)ISO 1234:1997(E) Foreword 180 (the international Organization for Standardization) is a worldwide {federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Intemational organizations, governmental and non- governmental, in liaison with ISO, also take part in the work, ISO collaborates closely with the Intemational Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Drait International Standards adopted by the technical committees are Circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard ISO 1234 was prepared by Technical Committee ISOITC 2, Fasteners. This second edition cancels and replaces the first edition (ISO 1234:1976), which has been technically revised, © 1801997 All rights reserved. Uniess otherwise epecified, no part of his publication may be reproduced ‘oF ullized in any form or by any means, electronic or mechanical, including pnatocopying and Iicrofim, without permission in wring ftom the publisher Intemational Organization for Standardization (Case postale 56» CH-1217 Geneve 20 « Switzeriand Intomst [email protected] % 400 c=ch; 2640000; prise; o-isoes; secentral Printed in SwitzeriangINTERNATIONAL STANDARD ©1so 1SO 1234:1997(E) _— Split pins 1 Scope This International Standard specifies the characteristics of split pins. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this international Standard are encouraged to investigate the Possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO ‘maintain registers of currently valid International Standards 1S0 3269:1988, Fasteners ~ Acceptance inspection. 1S0 4042:—", Fasteners ~ Electroplated coatings. 180 9717:1880, Phosphate conversion coatings for metals ~ Method of specifying requirements. 3 Dimensions See figure 1, table 1 and table 2 Shape of fends optional b, L a, 7 T qd Sy > Figure 1 1) To be published. (Revision of ISO 4042:1989),1SO 1234:1997(E) Table 1 — Dimensions (Lengths !: see table 2) Dimensions in miliimetres ‘Nominal size” os{ os] 1] a2] 16 2] 2s] a2 ¢ max, os] eo7/ o9[ 10} 4[ se] 2a] 20 win os] os? osf os] ssf az] arf 29 @ max w| re] se] 2s0f 280] 250] 2s0| a2 in, os] os] os] 1s] 125] 125/ 125| 16 ° = z{ ze] a 3] a2 a | os ¢ max vo] [ss] 20/ 2af ae] ae] sa in oo] 12] ss] [28] a2] a0] sa ‘Conesponaing Boks over -[| 25[ ss[ 4s] 5s 7 ef on diameters” to 2s| ss] 45] 55 7 e[ nf Clevis pins over -[ 2[ 3 + 5 6 8 9 0 2{ sf « 5 8 8 e{ 2 ‘Nominal size" a] s[ 6a 2] wl as] wl 2 @ max a7] ss] ssf zs[ 9s| wel wa] tea vin, as[ ssf s7] 7s] es] wal sal is0 a max. sf «te «| e30] sao] 620] cao rn at 2] 2 z{ sm| 3a5[ aa; ar ° + 8] wf wef wl ml om] 2] « « max. 74} 92] na] 150| 180 aos| S65 rin 6s| ao] wa] war] wel a7! aol ssa Conesponding Bolts over ul ml a] =! ssf a] 1] ciameters” to aol oa] a] s6{ e0| 0! 0 - Clevis pins over n{ ow] al wl ales] nol 160 to w{ wf af af es| 1] a0 = Ht9 for nominal size 1,2 H1¢ for nominal site > 1.2 1) Nominal size = dlameter ofthe split pin holes forthe pin hole ameter the following tolerance clagses are recommended. 2) For railway applications and in cases where split pins in clevis pins are subjected to alternating transverse forces, i is Fecommencied to use the next larger split pin sie t that specifiad in this table, esoIso ISO 1234:1997(E) Table 2 — Nominal lengths / and commercial lengths Dimensions in millimetres Tength ‘Nominal size rom | mm [mm |o6fos| 1 [12] 16| 2] 25/32] 4] 5 |e3| 8 | 0] 13] 16| 20 35] 65 75] 88 TT 0 [85] 0s epee wee ca Renae of wpa pe =e pa elapse = [ee ea 32 | 305) 335 commercial r | 36 | 345| a78 40 | 385/415 4% | 435| 466 rd lengths 50 | 485] 515 56 | 585] 575 63 | 615) 645 7 | 695] 725 Tr] iH 20 | 785] 815 (Ea) 90 | 88 | 9% yoo | 98 | i02 viz [a0 | ia | 125 | 123 | 127 — 140 | 138 | 142 160 | 158 | 162 ie0 [178 | 182 200 | 198 | 202 224 | 222 | 226 250 | 248 | 252 280 | 278 | 262ISO 1234:1997(E) eso 4 Requirements and reference International Standards See table 3. Table 3 — Requirements and reference international Standards Material Stool (St) Copper-zine alloy (Cu Zn) Copper (Cu) Aluminium alloy (Al) Austenitic stainless steet (A) Other materials as agreed between customer and supplier. Ductilty Each lag of the split pin shall be capable of withstanding being bent back upon itself once, with no visible indication of fracture occuring at the point of bend. Surface finish Piain i. parts to be supplied in natural finish, treated with a protective lubricant, oF with other coatings as agreed between customer and supplier. For electroplated coatings, see ISO 4042. For phosphate coating see ISO 9717, Workmanship Pins shall be free of burrs, irregularities and detrimental detects ‘The eye shall be as circular as possible. The cross-section of the two straight legs together shall be circular. ‘Acceptability For acceptance procedure, see ISO 3268. 5 Designation A split pin of nominal size § mm, nominal length 30 mm, made of steel (Sth is de: Split pin ISO 1234-5 x 50- StISO 1234:1997(E) e180 ICS 21.060.50 Descriptors: fasteners, steel products, pins (mechanics), spitpins. specications, characteristics, eimensions, designation, Price based on 4 pages oe