Scribd
Upload
210 views1 page

Idle Mode

Cell selection and reselection parameters in idle mode allow the UE to determine when to select or reselect cells. Parameters include thresholds for intra-frequency and inter-RAT reselection, hysteresis values, offsets, priorities, and timers. The UE measures the RX level of the serving and neighbor cells and performs reselection if the neighbor cell's level exceeds the serving cell's level by the specified thresholds and hysteresis after factoring in any priority or offset values. Certain parameters also control mobility states and discourage or encourage reselection.

Uploaded by

eduardo_pl8256
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
210 views1 page

Idle Mode

Cell selection and reselection parameters in idle mode allow the UE to determine when to select or reselect cells. Parameters include thresholds for intra-frequency and inter-RAT reselection, hysteresis values, offsets, priorities, and timers. The UE measures the RX level of the serving and neighbor cells and performs reselection if the neighbor cell's level exceeds the serving cell's level by the specified thresholds and hysteresis after factoring in any priority or offset values. Certain parameters also control mobility states and discourage or encourage reselection.

Uploaded by

eduardo_pl8256
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 1

IDLE MODE

Cell selection
There are QRXLEVMIN and QQUALMIN parameters (as in UMTS) to modify access criter
ia.
Pcompensation max(PEMAX PPowerClass, 0), pMaxServingCell, pMaxGeran I didn t undert
and this
- PMAX (max UE power)
- Criteria for camping of Less power UEs is hard, pMaxServingCell 1000
Reselection
Start Reselection:
SINTRASEARCH: threshold for intra freq cell reselection
SNONINTRASEARCH: threshold for IRAT reselection
TcrMaxConnMode (mobility calc) T_CRMAX_30S to T_CRMAX_60S will discourag
e reselection but increase precision, celResTiF, sIntrasearch, sNonIntrsearch I
didn t undertand this
QHYSTSFHIGH: additional hysteresis
QRXLEVMINOFFSET: additional QRXLEVMIN offset
TRESELECTIONRAT: reselection timer for IRAT (UTRAN or GERAN, depending o
n parameter, there should be one for each)
Reselection decision:
IDLEQHYST1S: Hysteresis for current cell as in UMTS
QOFFSETCELLEUTRAN: offset value for specific cell
CELLRESELPRIORITY: reselection priority for certain cell
NCELLRESELECTIONHIGH: to set the high mobility state (there are high, me
dium and low mobility states depending on UE speed)
threshXHigh, threshXLow, tReselectionEutraSfHigh, threshServingLow 62, s
PrioritySearch1 I didn t undertand this; I guess they are parameters related with
the above information, but not sure
interFrqThrH, tResEutSF, eutResTiFHM, celResTiFHM, cellReSelPrio 3 to 0
will discourage, mobStateParamNCelChgHgh, mobStateParamTEval, qRxLevMinOffset 0
to 2dB, q-RxLevMin, spStResPars, qHystSfHigh, tReselEutr, timeToTriggerSfMedium,
tResUtra, tResUtraSF, utrResTiFHM I didn t undertand this; I guess they are param
eters related with the above information, but not sure
QRX level measured: criteria (Rs reference level for current cell, Rn
re
ference level for neighbour cell):
Rs = Qmeas,s + QHYST
Rn = Qmeas,n + QOFFSET (or minus OFFSET, depending on vendor)
TEVALUATION: reselection evaluation time
T320: Time after RRCConnection Release in which cell reselection priorit
y info supplied in RRCConnectionRelease must be observed I didn t undertand this

HO

You might also like