ENGINEERS
STANDARD No.
SIGHT GLASSES FOR
601NDIA LIMITED
Oturqr
7-12-0017 Rev. 5
PRESSURE VESSELS
(A Govt. of Indio Undortoking)
I NO.-3mm NPT
TELLTALE HOLE
Page 1 of 2
GLASS
tfl
15
CLAD SHELL HEAD
SS OR CS SHELL HEAD
SIZE I
(NB)
50
100
50
100
P No.-14 HOLES
C
h STUD SIZE
DESIGN PRESSURE < 10 Kg / cm2g
152
50 92 38 24 91 10 20 120.5 4 19
230 100 157 38 29 156 16 28 190.5 8 19
DESIGN PRESSURE < 20 Kg / cm2g
165
50 92 38 27 91 14 20 127 8 19
255 100 157 40 37 156 22 28 200 8 22
1 N0.-3mm NPT
TELLTALE HOLE
SI
M 16
M 16
75
85
23
23
25
25
M 16
M 20
82
105
23
25
25
29
GLASS
SEE VESSEL DRG.
SIZE
(NB)
50
100
50
100
FLG. X
I.D.
P
T
G D t W
C
DESIGN PRESSURE < 10 Kg / cm2g
152 62 78 92 24 30 50 91 10
230 116 135 157 29 38 100 156 16
DESIGN PRESSURE .
165 62 84 92 27 38 50 91 14
255 116 146 157 37 53 100 156 22
h STUD SIZEI L
20 120.5 4 19
28 190.5 8 19
20 Kg / cm2g
20 127 8 19
28 200 8 22
M 16
M 16
100
115
28
28
M 16
M 20
110
145
28
32
THE ABOVE ARRANGEMENT IS APPLICABLE FOR THE FOLLOWING CONDITIONS.
DESIGN PRESSURE
20 Kg/cm2g
DESIGN TEMPERATURE < 200C
III) MAXIMUM TEMPERATURE DIFFERENTIAL
( AMBIENT TO FLUID )
140*C
30.07.2011
REAFFIRMED AND REISSUED AS STANDARD
POREL
RKT
AKM I SC
DM
11.09.2006
REAFFIRMED AND REISSUED AS STANDARD
POREL
DNN
AKM
VC
Rev.
No.
Date
Format No. 8-00-0001-F4 Rev.0
Purpose
Prepared
by
Checked
by
Stds. Bureau
Stds. Committee
Chairman
Convenor
Approved by
Copyright EIL - All rights reserved
ENGNEERS
INDIA LIMTED
fit
(A Govt. of Indio Undortoldng)
STANDARD No.
SIGHT GLASSES FOR
7-12-0017 Rev. 5
PRESSURE VESSELS
Page 2 of 2
16NOS.M12
TAPPED HOLES
16NOS.-15 0 HOLES
16
39R
1110.-3mm NPT
TELL-TAIL
HOLE
COVER FLANGE
GLASS
GASKET
(NOTE-9)
PAD FLANGE
THE ABOVE ARRANGEMENT IS APPLICABLE FOR THE FOLLOWING CONDITIONS.
DESIGN PRESSURE . 5.0 Kg/cm2g
DESIGN TEMPERATURE
200'C
III) MAXIMUM TEMPERATURE DIFFERENTIAL . 140*C
( AMBIENT TO FLUID )
NOTES
ALL DIMENSIONS ARE IN mm UNLESS OTHERWISE STATED.
IN CASE OF CONFLICT ENGINEERING DRAWING SHALL GOVERN.
TYPE OF SIGHT GLASS SHALL BE TOUGHENED BOROSILICATE AND SHALL BE TESTED
AS PER IS : 5428 / BS 3463.
FOR APPLICATION OUTSIDE THE LIMITS SPECIFIED ON THE STANDARDS, MANUFACTURER'S
PROVEN DESIGN FOR THE COMPLETE SIGHT GLASS ASSEMBLY SHALL BE USED.
UNLESS OTHERWISE SPECIFIED, GASKET MATERIAL SHALL BE COMPRESSED ARAMIDE GASKET OR
COMPRESSED FIBRE ASBESTOSFREE GASKET.
THE INDICATED SIGHT GLASS THICKNESSES ARE MINIMUM. NEGATIVE TOLERANCE IS NOT PERMITTED.
REFER ENGINEERING DRAWING FOR TYPE AND MATERIAL OF NOZZLE COMPONENTS.
GLASS AND SEAT FACE SHALL BE POLISHED PERFECTLY.
9. PROVIDE GASKET ON EITHER SIDE OF SIGHT GLASS.
30.07.2011
REAFFIRMED AND REISSUED AS STANDARD
POREL
KT
11.09.2006
REAFFIRMED AND REISSUED AS STANDARD
POREL
DNN
Rev.
No.
Date
Format No. 8-00-0001-F4 Rev.0
Purpose
Prepared
by
Checked
by
A M / SC
DM
AKM
VC
Stds. Committee
Stds. Bureau
Convenor
Chairman
Approved by
Copyright EIL - All rights reserved
